HUSH MINI by David Trubridge Ltd.
|
|
- Dwain Francis
- 5 years ago
- Views:
Transcription
1 Overall Dimensions - Model: 1034-B (240V) 1000 mm 1000 mm 400 mm 1
2 Contents (not to scale) Please double check all components are present and quantities are correct before beginning assembly x1 Top Panel Assembly Mini size: 280 mm (Power cable not shown) x20 Tapered Felt Panels Mini size: 650mm long x1 2.1m cable x40 (+5) Small Ratchet Rivets (13mm) x40 (+5) Large Ratchet Rivets (9mm) x1 Cone Gripper with Base x1 LED Driver (PCD B) x2 Folded Cardboard Pillars 1
3 Step 1 - Top Panel Ratchet Rivet Assembly Screw on x1 Cone Grippers (without bases) onto base already attached to top panel assembly Power Cord Suspension Wire Large Ratchet Rivet (19mm) Bend back gently Insert Large Ratchet Rivets (19mm) in all holes around edge. (power cord and suspension wires not shown) 2
4 Step 2 - Pop out side panel plugs x20 Push out the 4 plugs per panel to make way for the plastic clips. 3
5 Step 3 - Top Panel to Side Panel Assembly Assemble on a large clean surface or on floor. NOTE Ratchet Rivets must be pushed together fully for maximum strength Large Ratchet Rivet (19mm) x 20 Click Click Click NOTE: Do not put ratchet rivet on first panel until all panels have been clipped on. Proceed Anti Clockwise 4
6 Step 4 - Top Panel to Side Panel Assembly Continued First Last Tuck last panel under first panel and clip together with Large Ratchet Rivet Cross Section Detail View of Top Panels overlapping. 5
7 Step 5 - Lifting into shape Use suspension cable to lift the Hush Mini approximately 400mm from the floor/surface. The panels will begin to fall into their natural shape. Use the folded cardboard pillar that was in the box (or similar-sized table) to prop it up. Box Clean Floor / Table 6
8 Step 6A - Weaving of Panels - Exploded Detail Bold Lines indicate the Ear that sits on the outside of the Hush Mini. This weaving pattern is essential to lock the shape together Click Click Click Once two panels are woven together, use two of the shorter Ratchet Rivets (13 mm) to lock them together. 7
9 Step 6A - Weaving of Panels - Finished Detail Bold Lines indicate the Ear that sits on the outside of the Hush Mini. This weaving pattern is essential to lock the shape together 8
10 Step 7 - Height Adjustment and Levelling Ceiling Mounting Point. If installing into wood use a countersunk timber screw (not supplied) to affix cone grip to ceiling. If installing into concrete use countersunk anchor bolt (not supplied) to affix cone grip to ceiling. push To shorten wire: Pull cable through hole in side of gripper point To lengthen wire: Depress cylinder at top of gripper point and pull wire out 9
11 Step 8 - Electrics, Suggested LED driver placement with hanging ceiling Concrete To Mains Power LED Driver Hung Ceiling IMPORTANT: ENSURE LED DRIVER AND MAINS CONNECTION IS WIRED BY A CERTIFIED ELECTRICIAN SEE APPENDIX 1 FOR DRIVER INFORMATION 10
12 Appendix 1: LED Driver Diagram MEANWELL 16W Single Output C Dimmable LED Power Supply (PCD B) V+ (Red) AC/N (Blue) V- (Black) AC/L (Brown) IMPORTANT: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED 11
13 Appendix 2: Access to LED Lights for maintenance To gain access to the LEDs, remove the 3 small screws. 12
14 Appendix 3: Top Panel Sub Assembly Aluminium Disk (LEDs on underside) Plastic Spacer Disk Felt Panel 3 x 12mm Screws Exploded View Assembled View 13
HUSH MINI by David Trubridge Ltd.
Overall Dimensions - Model: 1034-A 1000mm 1000mm 400mm www.iqcommercial.co.nz Contents (not to scale) Please double check all components are present and quantities are correct before beginning assembly
More informationOverall Dimensions - Model: 1018-A. 575mm. 1400mm. 600mm. 2000mm
Overall Dimensions - Model: 1018-A 1400mm 575mm 600mm 2000mm Contents (Not to scale) Please double check all components are present and quantities are correct before beginning assembly x8 Straight Felt
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationPRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)
More informationWOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
More informationInstallation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:
Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free
More informationMini Cooper Lock Actuator
2001-2006 Mini Cooper Lock Actuator Replacement This guide is on how to remove the lock actuator from the cars door. Written By: Jem ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION In order
More informationOriginal Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationCROWN IMPERIAL ASSEMBLY INSTRUCTIONS
CROWN IMPERIAL ASSEMBLY INSTRUCTIONS Standard Drawer Box Page 1 of 14 Standard Drawer Box Parts Parts Supplied B C D A E F G Page 2 of 14 Part Letter Part Name Quantity 300-600 Deep Pan A Base Panel 1
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationArt and Picture Hanging Rail Systems SYSTEMS. Display with Elegance
Art and Picture Hanging Rail Systems SYSTEMS Display with Elegance Table of Contents Classic Rail +..... 1 Click Rail...... 4 Top Rail...... 8 Info Rail...... 10 Deco Rail...... 12 Wires and Hooks...................
More informationx2 1/4 (6mm) Floor Anchor
Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x 90mm) Wall Screw x2
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationPLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE
HONEYCOMB AND PLEATED SHADE ARCH GETTING STARTED INSIDE MOUNT A few simple tools are required: HALF ARCH INSTALLATION Your half arch has been shipped in the closed osition. When fanned, the rails will
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More informationHawko Zhaga Systems Installation Instructions
Hawko Zhaga Systems Installation Instructions Contents Wire Suspension Installation 4 Recessed Brackets 6 Fixed Suspension Rods 8 Swivel Suspension Rods 10 Surface Mount Ceiling 12 Surface Mount Wall
More informationREPLACEMENT TARP for SRT-2 SPOOL ROLL TARP
REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components
More informationRotary Fixture M/V/X CLASS LASER SYSTEMS. Installation and Operation Instructions
Rotary Fixture M/V/X CLASS LASER SYSTEMS Installation and Operation Instructions 02/01/2000 Introduction The Rotary Fixture controls in the Printer Driver are used along with the optional Rotary Fixture
More informationOhbot. Eyes turn. servo. Eyelids open. servo. Head tilt. servo Eyes tilt. servo. Mouth open servo. Head turn servo
Making Instructions Ohbot Ohbot has six servo motors. The servos allow each part of the face to be positioned precisely. Eyelids open servo Eyes tilt servo Eyes turn servo Head tilt servo Mouth open servo
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationBARN DOOR HARDWARE KIT
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationLCD LIFT Flat Panel Display System Installation Manual. Table of Contents
LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate
More informationPlease read through all instructions carefully before you begin. Unpack all materials, making sure all parts are included:
Somfy Motorized Track Installation Instructions Materials Please read through all instructions carefully before you begin. Unpack all materials, making sure all parts are included: Mounting Brackets Track
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More informationSM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL
SM-RAZOR-F-M/L/XL Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationInstallation Guide. VONN Lighting Model: VMC Parts List. Circuit Box. Tools You May Need
VONN Lighting Model: VMC32420 Installation Guide LED INFO & WRNINGS Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. Make sure that you have
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationVinyl Cutter Instruction Manual
Vinyl Cutter Instruction Manual 1 Product Inventory Inventory Here is a list of items you will receive with your vinyl cutter: Product components (Fig.1-4): 1x Cutter head unit complete with motor, plastic
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationCordless Operable Sidelights
Installation Instructions Parasol Cellular Shades Cordless Operable Sidelights CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationInstruction Manual. Manual Furniture Mover. Note: Owner/Operator must read and understand this instruction manual before using the furniture mover.
Instruction Manual Manual Furniture Mover Note: Owner/Operator must read and understand this instruction manual before using the furniture mover. I - Contents 1. Application 2 Specifications 3.Assembly
More informationFACTORY STRETCH INSTALLATION INSTRUCTIONS
!! Important!! Make sure all power is disconnected prior to installation. Wiring to be done according to Local and National Electric Codes by a qualified electrician. Make sure the building and/or structure
More informationLuxe Linen Honeycomb Shades
Step by Step Installation Instructions Luxe Linen Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Table of Contents Getting Started...3 THANK YOU for purchasing from
More informationWHISPER Cellular EasyRise Shades. Installation Operation Care
WHISPER Cellular EasyRise Shades Installation Operation Care 05/2013 CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mounting Types
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.
More informationInterra Installation Manual
Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationInstallation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
More informationConstable Oak Extension Dining Table
Constable Oak Extension Dining Table Assembly Instructions - Please keep for future reference 176/0325 Dimensions Width - 160/ 200cm Depth - 90cm Height - 75cm Important - Please read these instructions
More informationOperating & Maintenance Instructions 280 Hot Wire Sculptor
Operating & Maintenance Instructions 280 Hot Wire Sculptor Table of Contents Assembly & Operation... 2 Electrical Supply and Connection... 8 Technical Specification... 8 Fault Finding... 8 Connection Diagram...
More informationThor Audi A4/S4 Skid Plate Installation Instructions
Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts
More informationAudi Q7 Running board Fitting Instructions
Audi Q7 Running board Fitting Instructions Parts list Item Designation 1 2 3 4 5 6 7 Running board Support bracket Covers Screw M8x40 Screw M8x20 Blind rivet Screw for plating 4.8x16 Quantity 2 6 4 14
More informationInstructions & Safety Information
Sept 2018 Design by Thomas Housden TERR ACOT TA MEDIUM Material & Style Terracotta & White Glaze Top or Inside Only Glaze Styles Dimensions & Weight Ø270mm H200mm 2.5Kg Lamp Type & Wattage E27 lamp Max
More information1 Removing The Screen Track, Screen and Screen Rollers Note: The screen remains in the track while the track is removed and/or installed.
Sliding Door Screen and Screen Track Replacement Service Instruction These instructions apply to: Architect Series 12/2004-Current Designer Series 3/2005-Current Tools Required: #2 Phillips head screwdriver
More informationP/N LED LIGHTS 6509/9012/12012 MACHINES
P/N 090517 LED LIGHTS 6509/9012/12012 MACHINES 4 1 8 12 5 9 13 2 6 10 3 7 11 14 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 18 IN. 660461 18/2 SVO CORD 2 1 090508 LED LIGHT TRANSFORMER 3
More informationSCHACHT STANDARD FLOOR LOOMTM
SCHACHT STANDARD FLOOR LOOMTM FL3109 FL3111 FL3113 FL3115 FL3121 FL3123 FL3125 FL3127 FL3310 FL3312 FL3314 FL3316 FL3322 FL3324 FL3326 FL3328 Assembly instructions LOW CASTLE LOOM IN MAPLE Find out more
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationHighway Care Ltd. Xtension 110 P4 Terminal & Xtension 110 Double Sided P4 Terminal DESIGN, INSTALLATION & MAINTENANCE MANUAL REVISION 1E
Xtension 110 P4 Terminal & Xtension 110 Double Sided P4 Terminal DESIGN, INSTALLATION & MAINTENANCE MANUAL REVISION 1E Highway Care Limited Page 1 Revision 1E Contents Page Introduction 3 Before Installation
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationL182 - Installation Sheet Modular Wine Rack ( Wall Mount )
Modular Wine Rack ( Wall Mount ) 1A 1B 2B 2A Cross Bar Options: 1A 2A 1B 2B Modular Wine Rack ( Wall Mount ) Parts Rail LED arm modules Wine bottle cross bars Rail cover Setscrew cover 1) Drill holes and
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationINSTALLATION. Preparation:
INSTALLATION Preparation: Average Time Required: 2 to 3 hours Place a blanket down in the area which you will be working in. This will prevent scratches on the rear fascia / valance. Remove your License
More informationProduct must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.
General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service
More informationCorded Honeycomb Shades
Corded Honeycomb Shades Remove shade from package. Save packaging until shade is installed and working to your satisfaction. Level Tape Measure Pencil Power drill Screwdriver s for different mounting surface:
More informationWallboard or plastic Pre-drill holes and use hollow wall anchors or toggle bolts to install your shade in wallboard or plastic.
Woven Wood Shades Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing Woven Wood Shades from Blindster. This window
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationInstallers guide Deadbolt 02.
Installers guide Deadbolt 02. version 0.7.1 Specifications Model igloohome Smart Deadbolt 02 Material Zinc Alloy Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationAngled Side Flush with Panel Face
Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.
More informationRB12 AERO - SINGLE INSTALLATION MANUAL. April 2017
RB12 AERO - SINGLE INSTALLATION MANUAL April 2017 CONTENTS April 2017 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION
More informationTM12 ASSEMBLY INSTRUCTIONS
TM12 ASSEMBLY INSTRUCTIONS Congratulations on purchasing the finest purple martin house available. Nature House Brand houses are the proven leader in aluminum martin housing for over half a century. After
More informationInstalling Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image
UX60-RFK-685 Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image Follow these instructions to install brackets on your SMART Board 685ix
More informationPRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR & Assembly Installation Instructions 4884 HSD Standard Sliding Door Components Some Considerations When Choosing Your Stall System - 1
More informationInstalling the 3 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing the 3 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Route Cable into Box...5
More informationSport-Thieme Safety Aluminium Mini Training Goal
Assembly instructions Art.-Nr.: 116 3881 Sport-Thieme Safety Aluminium Mini Training Goal 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com Phone: +49 53
More informationPERSONAL RECORD KEEPING
2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain
More informationRolling Curtain door Manual
Rolling Curtain door Manual Installation Maintenance parts Model 944 PHONE 800 448 8979 FAX 800 236 8722 website www.tracrite.com EMAIL tr@tracrite.com ADDRESS 216 Wilburn Road Sun Prairie, WI 53590 This
More informationTools Needed Hardware Provided (per shade) Hardware Needed
Baby Grande or Grande Motorized (XQ5 Premium) Shade with Cables and Housing Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit Measuring Tape
More informationCeiling mount for BW1 THEATRE Concept (R ) INSTALLATION MANUAL. Part. No.: R Date: Rev: 01
Ceiling mount for BW1 THEATRE Concept (R9852065) INSTALLATION MANUAL www.cineversum.com Date: 10112008 Rev: 01 Part. No.: R599769 Assembly Instructions: This product is designed to be used in private homes.
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)
ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly
More informationSTORAGE & SHELVING SYSTEM - INSTALLATION GUIDE
STORAGE & SHELVING SYSTEM - INSTALLATION GUIDE If you have ordered storage drawers, shelving, hanging rails or shoe racks this guide will help you install your storage and shelving system, together with
More informationYES 12 Charging Wall Cabinet for Mini-laptops
Built with Anthro-DNA Owner's Manual for YES 12 Charging Wall Cabinet for Mini-laptops Part # YESMLCGMPW Components at a Glance 7 1 9 8 2 4 5 11 6 10 3 Front of Cabinet (closed) 1. Locking front door to
More informationInstallation Instructions 8115F 8115SF
TM Installation Instructions 85F 85SF Single Control Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature
More information*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices
*D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationINSTALLATION INSTRUCTIONS FOR A&L PRODUCTS
INSTALLATION INSTRUCTIONS FOR A&L PRODUCTS AUGUST 2017 1 RECOMMENDED BUILDING IN-DETAIL Should you require further information, please contact A&L Windows on 1800 441 414 2 IMPORTANT IMPORTANT Allow Vinyl
More informationInstructions and Parts List MSS-12W MARTIN SAFETY SYSTEM
HOUSE PARTS PACKED IN HOUSE BOX Code # Item Qty Description 950 9776 77 85036 500 868 635 9635 5075 860 3578 8507 60 6 95065 6 98000 7800 7806 3 5 6 7 7A 8 9 0 3 5 6 6A 6B 8 Instructions and Parts List
More informationConnect each sections electricity cables with a connections block or splices and heatshrink. Proceed to Myla installation manual.
MYLA L & XL ASSEMBLY 1. 2. PARTS 3-5 SECTIONS Prepare a soft clean workspace to assemble the light fixture. Carefully unpack the light fixture and other contents. Myla L consists of 3 separate sections
More information6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationInstallation Instructions Window Opening Control Device. Single-Hung & Sliding Windows with No Vent Latches
Single-Hung & Sliding Windows with No Vent Latches These s (WOCDs) work with single-hung windows and sliding windows with one operational and one stationary sash in the confi gurations of either XO or
More informationDoor window. Front door window, assembly overview
64-50 Door window Front door window, assembly overview 1 - Window channel Pushed onto flange 2 - Door window Removing Page 64-52 Adjusting Page 64-53 3 - Door 4 - Outer window channel Pushed onto flange
More informationINSTALLATION MANUAL H A
INSTALLATION MANUAL CABINET RACK CR-43-6 (4-UNIT SIZE) Be sure to read this installation manual thoroughly before installing this Cabinet Rack. For the mounting procedures of the components and the relevant
More informationInstallation Instructions
Installation Instructions Transitional Shades Standard Transitional Shades (Small and Large Cassette) Board Mounted Transitional Shades Accu-Rise Transitional Shades Sure-Lift Transitional Shades Sundown
More informationInstallation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness
Installation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness Step 1. Fold template where indicated. Position template on door edge at desired lock / latch
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationinstallation instructions WC Frame 1180mm with Dual Flush Cistern
installation instructions WC Frame 1180mm with Dual Flush Cistern (C,D,E) K F/G N L M 12 13 14 16 1 2 11 A 5 6 Q O Y 3 C 10 E D B P,Z,AA R T V S 4 U 2 No. Part no. Description Quantity A WC Frame with
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 Front of Cabinet (closed) 1. Locking front door to User area. 2.
More information