ECE513 RF Design for Wireless
|
|
- Claribel Moody
- 5 years ago
- Views:
Transcription
1 1 ECE513 RF Design for Wireless MODULE 1 RF Systems LECTURE 1 Modulation Techniques Chapter 1, Sections Professor Michael Steer
2 2 Module 1: RF Systems Amplifiers, Mixers & Oscillators Antennas and RF Link Radio Frequency Systems Aim is to develop a full appreciation of an RF communication, focus is on a cellular radio system. System requirements drive component and subsystem development. Also capabilities of components and subsystems drive systems.
3 3 Module 1: Lecture 1 Amplifiers, Mixers & Oscillators RF Front Ends RF signals Analog Modulation Digital Modulation
4 4 Lecture Goal Develop an understanding of modulation techniques used in analog and digital cellular radio. Lecture Outline Analog Modulation: AM, FM, PM Introduction to Digital Modulation: ASK, FSK, PSK Advanced Modulation Concepts Occupied Bandwidth Performance of Modulation Types used in Cellular Radio Analog FM, DQPSK, FSK, GMSK
5 5 A Modulator I K WAVEFORM SHAPING I i(t) a(t) SERIAL BIT STREAM SERIAL TO PARALLEL VCO 90 s(t) Q K WAVEFORM SHAPING q(t) Q b(t)
6 6 Performance of Different Modulation Types Each type of modulation has advantages and drawbacks: Necessary bandwidth How wide is the signal? How much spectrum is needed? How big a "guard band" is needed between channels? Relative vulnerability to interference What C/I ratio is required for good system performance? Relative difficulty of implementation Is complex equipment required? Implementation cost? Maintainability
7 7 Analog Modulation Modulation is the process of varying some characteristic of a radio signal in order to convey information Time This analog waveform modulates a sinewave. The basic, unchanging, steady radio signal without modulation is called a carrier. Characteristics that can be modulated: Amplitude e.g. AM radio broadcasting Frequency e.g. FM broadcasting, Voice transmission in AMPS cellular Phase Note that frequency and phase modulation look very similar with this kind of input.
8 8 Amplitude Modulation (AM) [ ] xt ( ) = A 1+ mcosω t cosω t c m c The First Radio System to Transmit Voice were based on amplitude modulation.
9 9 Peak-to-Average Ratio CW Envelope AM (100%) ENVELOPE v peak v average = ½ v peak PAR = 4.26 db RF Power FM PAR = 0 db With FM amplitude distortion does not matter as there is no information in the amplitude of the signal.
10 10 PAR Peak-to-Average Ratio of AM [ ] xt ( ) = A 1+ mcosω t cosω t c m c PAR is an important metric for modulation formats Determines how amplifier must be designed for specified distortion. [ ] xpeak ( t ) = Ac 1 + m cos ω t c
11 11 PAR 1/4 [ ] x ( ) 1 cos PEAK t = Ac + m ωct
12 12 PAR 2/4 τ 1 2 avg lim τ 2τ ( ) τ P = Gv t. dt.
13 13 PAR 3/4 [ ω ] xt ( ) = A 1+ mcos t cosω t c m c
14 14 PAR 4/4 [ ω ] xt ( ) = A 1+ mcos t cosω t c m c
15 15 Analog FM How Much Bandwidth is Required? Time Carrier -3f i Input Signal -2f i -f i c +f i f i = input signal frequency frequency deviation Frequency Sidebands +2f i +3f i Frequency As time passes, the carrier moves back and forth in frequency in exact step with the input signal frequency deviation is proportional to the input signal voltage a group of many sidebands is created, spaced from carrier by amounts N x f i relative strength of each sideband N depends on Bessel function N of (input signal freq./freq. deviation) strength of individual sidebands far away from the carrier is proportional to (freq. deviation x input frequency) Carson s Rule Bandwidth Required = 2 x (highest input frequency + frequency deviation)
16 16 Analog Modulation and Bandwidth Time-Domain (as viewed on an Oscilloscope) Time Frequency-Domain (as viewed on a Spectrum Analyzer) 0 Lower Sideband Frequency Upper Sideband The bandwidth occupied by a signal depends on: input information bandwidth modulation method Information to be transmitted, called input or baseband bandwidth usually is small, much lower than frequency oarrier Unmodulated carrier the carrier itself has Zero bandwidth!! AM-modulated carrier Notice the upper & lower sidebands total bandwidth = 2 x baseband FM-modulated carrier Many sidebands! bandwidth is a complex mathematical function PM-modulated carrier Many sidebands! bandwidth is a complex mathematical function
17 17 Analog Modulation and PAR Time 0 Frequency CARRIER 100% AM Lower Sideband Upper Sideband FM PM
18 18 Narrow Band Communication The majority of modulation formats result in narrow band communication systems AM These were the easiest modulation schemes for most of the 20 th century and dictated the assignment of radio into narrow band channels. FDMA AMPLITUDE FREQUENCY 1912: Regulation began with the sinking of the Titanic.
19 19 Frequency Modulation & Bandwidth Time-Domain (as viewed on an Oscilloscope) Time Frequency-Domain (as viewed on a Spectrum Analyzer) 0 Frequency The bandwidth occupied by a signal depends on: input information bandwidth modulation method Information to be transmitted, called input or baseband bandwidth usually is small, much lower than frequency oarrier FM-modulated carrier Many sidebands! bandwidth is a complex mathematical function The bandwidth requirement for a frequency modulated signal is difficult to determine for arbitrary modulating signals as the frequency spectrum of this signal extends indefinitely but the amplitude of the spectrum falls off rapidly.
20 20 Analog FM How Much Bandwidth is Required? Time Carrier -3f i Input Signal -2f i -f i c +f i f i = input signal frequency frequency deviation Frequency Sidebands +2f i +3f i Frequency As time passes, the carrier moves back and forth in frequency in exact step with the input signal frequency deviation is proportional to the input signal voltage a group of many sidebands is created, spaced from carrier by amounts N x f i relative strength of each sideband N depends on Bessel function N of (input signal freq./freq. deviation) strength of individual sidebands far away from the carrier is proportional to (freq. deviation x input frequency) Carson s Rule Bandwidth Required = 2 x (highest input frequency + frequency deviation)
21 21 Narrowband and Wideband FM The difference is between what are called Narrowband FM and Wideband FM. The best rule of thumb formula is Carson s Rule: Bandwidth Required = B R = 2 x (highest input frequency + frequency deviation) Let's replace this by B R = Bandwidth Required F = frequency deviation f m = highest input frequency (bandwidth of modulating signal) So B R = 2 * ( F + f m ) Narrowband FM is when F << f m and then it can be shown that the bandwidth required is 2 * f m but only for Frequency Shift Keying (FSK) which is a two state form of FM. Wideband FM is when F >> f m and then it can be shown that the bandwidth required is 2 * F.
Modulation, Transmitters and Receivers
CHAPTER 1 Modulation, Transmitters and Receivers 1.1 Introduction........................................................... 1 1.2 RF Signals............................................................
More informationModulation is the process of impressing a low-frequency information signal (baseband signal) onto a higher frequency carrier signal
Modulation is the process of impressing a low-frequency information signal (baseband signal) onto a higher frequency carrier signal Modulation is a process of mixing a signal with a sinusoid to produce
More informationOutline. Communications Engineering 1
Outline Introduction Signal, random variable, random process and spectra Analog modulation Analog to digital conversion Digital transmission through baseband channels Signal space representation Optimal
More informationAngle Modulated Systems
Angle Modulated Systems Angle of carrier signal is changed in accordance with instantaneous amplitude of modulating signal. Two types Frequency Modulation (FM) Phase Modulation (PM) Use Commercial radio
More informationAnalog Communication.
Analog Communication Vishnu N V Tele is Greek for at a distance, and Communicare is latin for to make common. Telecommunication is the process of long distance communications. Early telecommunications
More informationChapter 3 Communication Concepts
Chapter 3 Communication Concepts 1 Sections to be covered 3.1 General Considerations 3.2 Analog Modulation 3.3 Digital Modulation 3.4 Spectral Regrowth 3.7 Wireless Standards 2 Chapter Outline Modulation
More informationUNIT-2 Angle Modulation System
UNIT-2 Angle Modulation System Introduction There are three parameters of a carrier that may carry information: Amplitude Frequency Phase Frequency Modulation Power in an FM signal does not vary with modulation
More informationEE470 Electronic Communication Theory Exam II
EE470 Electronic Communication Theory Exam II Open text, closed notes. For partial credit, you must show all formulas in symbolic form and you must work neatly!!! Date: November 6, 2013 Name: 1. [16%]
More informationELEC3242 Communications Engineering Laboratory Frequency Shift Keying (FSK)
ELEC3242 Communications Engineering Laboratory 1 ---- Frequency Shift Keying (FSK) 1) Frequency Shift Keying Objectives To appreciate the principle of frequency shift keying and its relationship to analogue
More informationMaster Degree in Electronic Engineering
Master Degree in Electronic Engineering Analog and telecommunication electronic course (ATLCE-01NWM) Miniproject: Baseband signal transmission techniques Name: LI. XINRUI E-mail: s219989@studenti.polito.it
More informationLecture 6. Angle Modulation and Demodulation
Lecture 6 and Demodulation Agenda Introduction to and Demodulation Frequency and Phase Modulation Angle Demodulation FM Applications Introduction The other two parameters (frequency and phase) of the carrier
More informationChapter 7 Multiple Division Techniques for Traffic Channels
Introduction to Wireless & Mobile Systems Chapter 7 Multiple Division Techniques for Traffic Channels Outline Introduction Concepts and Models for Multiple Divisions Frequency Division Multiple Access
More informationTSEK02: Radio Electronics Lecture 2: Modulation (I) Ted Johansson, EKS, ISY
TSEK02: Radio Electronics Lecture 2: Modulation (I) Ted Johansson, EKS, ISY 2 Basic Definitions Time and Frequency db conversion Power and dbm Filter Basics 3 Filter Filter is a component with frequency
More informationTwelve voice signals, each band-limited to 3 khz, are frequency -multiplexed using 1 khz guard bands between channels and between the main carrier
Twelve voice signals, each band-limited to 3 khz, are frequency -multiplexed using 1 khz guard bands between channels and between the main carrier and the first channel. The modulation of the main carrier
More informationModulation in Telemetry Chapter 3
TEMPEST Engineering and Hardware Design Dr. Bruce C. Gabrielson, NCE 1998 Modulation in Telemetry Chapter 3 Introduction Relative to low power signal transmission, not only must an engineer be able to
More informationUNIT 1 QUESTIONS WITH ANSWERS
UNIT 1 QUESTIONS WITH ANSWERS 1. Define modulation? Modulation is a process by which some characteristics of high frequency carrier signal is varied in accordance with the instantaneous value of the modulating
More informationCSCD 433 Network Programming Fall Lecture 5 Physical Layer Continued
CSCD 433 Network Programming Fall 2016 Lecture 5 Physical Layer Continued 1 Topics Definitions Analog Transmission of Digital Data Digital Transmission of Analog Data Multiplexing 2 Different Types of
More informationChapter 3. Amplitude Modulation Fundamentals
Chapter 3 Amplitude Modulation Fundamentals Topics Covered 3-1: AM Concepts 3-2: Modulation Index and Percentage of Modulation 3-3: Sidebands and the Frequency Domain 3-4: AM Power 3-5: Single-Sideband
More informationTechnician License Course Chapter 2. Lesson Plan Module 3 Modulation and Bandwidth
Technician License Course Chapter 2 Lesson Plan Module 3 Modulation and Bandwidth The Basic Radio Station What Happens During Radio Communication? Transmitting (sending a signal): Information (voice, data,
More informationTSEK02: Radio Electronics Lecture 2: Modulation (I) Ted Johansson, EKS, ISY
TSEK02: Radio Electronics Lecture 2: Modulation (I) Ted Johansson, EKS, ISY An Overview of Modulation Techniques: chapter 3.1 3.3.1 2 Introduction (3.1) Analog Modulation Amplitude Modulation Phase and
More informationWireless Communication Fading Modulation
EC744 Wireless Communication Fall 2008 Mohamed Essam Khedr Department of Electronics and Communications Wireless Communication Fading Modulation Syllabus Tentatively Week 1 Week 2 Week 3 Week 4 Week 5
More informationCOMM 601: Modulation I
Prof. Ahmed El-Mahdy, Communications Department The German University in Cairo Text Books [1] Couch, Digital and Analog Communication Systems, 7 th edition, Prentice Hall, 2007. [2] Simon Haykin, Communication
More informationTechnician License Course Chapter 2. Lesson Plan Module 2 Radio Signals and Waves
Technician License Course Chapter 2 Lesson Plan Module 2 Radio Signals and Waves The Basic Radio Station What Happens During Radio Communication? Transmitting (sending a signal): Information (voice, data,
More informationAmplitude Modulated Systems
Amplitude Modulated Systems Communication is process of establishing connection between two points for information exchange. Channel refers to medium through which message travels e.g. wires, links, or
More informationIntroduction to Amplitude Modulation
1 Introduction to Amplitude Modulation Introduction to project management. Problem definition. Design principles and practices. Implementation techniques including circuit design, software design, solid
More informationINTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA
COMM.ENG INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA 9/9/2017 LECTURES 1 Objectives To give a background on Communication system components and channels (media) A distinction between analogue
More informationCollege of information Technology Department of Information Networks Telecommunication & Networking I Chapter 5. Analog Transmission
Analog Transmission 5.1 DIGITAL-TO-ANALOG CONVERSION Digital-to-analog conversion is the process of changing one of the characteristics of an analog signal based on the information in digital data. The
More informationElements of Communication System Channel Fig: 1: Block Diagram of Communication System Terminology in Communication System
Content:- Fundamentals of Communication Engineering : Elements of a Communication System, Need of modulation, electromagnetic spectrum and typical applications, Unit V (Communication terminologies in communication
More informationCHAPTER 2! AMPLITUDE MODULATION (AM)
CHAPTER 2 AMPLITUDE MODULATION (AM) Topics 2-1 : AM Concepts 2-2 : Modulation Index and Percentage of Modulation 2-3 : Sidebands and the Frequency Domain 2-4 : Single-Sideband Modulation 2-5 : AM Power
More informationExperiment One: Generating Frequency Modulation (FM) Using Voltage Controlled Oscillator (VCO)
Experiment One: Generating Frequency Modulation (FM) Using Voltage Controlled Oscillator (VCO) Modified from original TIMS Manual experiment by Mr. Faisel Tubbal. Objectives 1) Learn about VCO and how
More informationISHIK UNIVERSITY Faculty of Science Department of Information Technology Fall Course Name: Wireless Networks
ISHIK UNIVERSITY Faculty of Science Department of Information Technology 2017-2018 Fall Course Name: Wireless Networks Agenda Lecture 4 Multiple Access Techniques: FDMA, TDMA, SDMA and CDMA 1. Frequency
More informationECE 4600 Communication Systems
ECE 4600 Communication Systems Dr. Bradley J. Bazuin Associate Professor Department of Electrical and Computer Engineering College of Engineering and Applied Sciences Course Topics Course Introduction
More informationLab Assignment #3 Analog Modulation (An Introduction to RF Signal, Noise and Distortion Measurements in the Frequency Domain)
Lab Assignment #3 Analog Modulation (An Introduction to RF Signal, Noise and Distortion Measurements in the Frequency Domain) By: Timothy X Brown, Olivera Notaros, Nishant Jadhav TLEN 5320 Wireless Systems
More informationLecture Topics. Doppler CW Radar System, FM-CW Radar System, Moving Target Indication Radar System, and Pulsed Doppler Radar System
Lecture Topics Doppler CW Radar System, FM-CW Radar System, Moving Target Indication Radar System, and Pulsed Doppler Radar System 1 Remember that: An EM wave is a function of both space and time e.g.
More informationIntroduction. In the frequency domain, complex signals are separated into their frequency components, and the level at each frequency is displayed
SPECTRUM ANALYZER Introduction A spectrum analyzer measures the amplitude of an input signal versus frequency within the full frequency range of the instrument The spectrum analyzer is to the frequency
More informationAnnouncements : Wireless Networks Lecture 3: Physical Layer. Bird s Eye View. Outline. Page 1
Announcements 18-759: Wireless Networks Lecture 3: Physical Layer Please start to form project teams» Updated project handout is available on the web site Also start to form teams for surveys» Send mail
More informationCSCD 433 Network Programming Fall Lecture 5 Physical Layer Continued
CSCD 433 Network Programming Fall 2016 Lecture 5 Physical Layer Continued 1 Topics Definitions Analog Transmission of Digital Data Digital Transmission of Analog Data Multiplexing 2 Different Types of
More information(b) What are the differences between FM and PM? (c) What are the differences between NBFM and WBFM? [9+4+3]
Code No: RR220401 Set No. 1 1. (a) The antenna current of an AM Broadcast transmitter is 10A, if modulated to a depth of 50% by an audio sine wave. It increases to 12A as a result of simultaneous modulation
More informationDigital Communication System
Digital Communication System Purpose: communicate information at required rate between geographically separated locations reliably (quality) Important point: rate, quality spectral bandwidth, power requirements
More informationRadio Technology and Architectures. 1 ENGN4521/ENGN6521: Embedded Wireless L#1
Radio Technology and Architectures 1 ENGN4521/ENGN6521: Embedded Wireless L#1 Radio (Architectures) Spectrum plan and legal issues Radio Architectures and components 2 ENGN4521/ENGN6521: Embedded Wireless
More informationAmplitude Modulation. Ahmad Bilal
Amplitude Modulation Ahmad Bilal 5-2 ANALOG AND DIGITAL Analog-to-analog conversion is the representation of analog information by an analog signal. Topics discussed in this section: Amplitude Modulation
More informationAngle Modulation, II. Lecture topics. FM bandwidth and Carson s rule. Spectral analysis of FM. Narrowband FM Modulation. Wideband FM Modulation
Angle Modulation, II Lecture topics FM bandwidth and Carson s rule Spectral analysis of FM Narrowband FM Modulation Wideband FM Modulation Bandwidth of Angle-Modulated Waves Angle modulation is nonlinear
More informationUNIT-I AMPLITUDE MODULATION (2 Marks Questions and Answers)
UNIT-I AMPLITUDE MODULATION (2 Marks Questions and Answers) 1. Define modulation? Modulation is a process by which some characteristics of high frequency carrier Signal is varied in accordance with the
More information15.Calculate the local oscillator frequency if incoming frequency is F1 and translated carrier frequency
DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING SUBJECT NAME:COMMUNICATION THEORY YEAR/SEM: II/IV SUBJECT CODE: EC 6402 UNIT I:l (AMPLITUDE MODULATION) PART A 1. Compute the bandwidth of the AMP
More informationEXPERIMENT WISE VIVA QUESTIONS
EXPERIMENT WISE VIVA QUESTIONS Pulse Code Modulation: 1. Draw the block diagram of basic digital communication system. How it is different from analog communication system. 2. What are the advantages of
More informationAM, PM and FM mo m dula l ti t o i n
AM, PM and FM modulation What is amplitude modulation In order that a radio signal can carry audio or other information for broadcasting or for two way radio communication, it must be modulated or changed
More informationLecture 2: Links and Signaling. CSE 123: Computer Networks Stefan Savage
Lecture 2: Links and Signaling CSE 123: Computer Networks Stefan Savage Lecture 2 Overview Signaling Channel characteristics Types of physical media Modulation Narrowband vs. Broadband Encoding schemes
More informationLecture 13. Introduction to OFDM
Lecture 13 Introduction to OFDM Ref: About-OFDM.pdf Orthogonal frequency division multiplexing (OFDM) is well-known to be effective against multipath distortion. It is a multicarrier communication scheme,
More informationEE12: Laboratory Project (Part-2) AM Transmitter
EE12: Laboratory Project (Part-2) AM Transmitter ECE Department, Tufts University Spring 2008 1 Objective This laboratory exercise is the second part of the EE12 project of building an AM transmitter in
More informationMultiplexing Module W.tra.2
Multiplexing Module W.tra.2 Dr.M.Y.Wu@CSE Shanghai Jiaotong University Shanghai, China Dr.W.Shu@ECE University of New Mexico Albuquerque, NM, USA 1 Multiplexing W.tra.2-2 Multiplexing shared medium at
More informationECE5713 : Advanced Digital Communications
ECE5713 : Advanced Digital Communications Bandpass Modulation MPSK MASK, OOK MFSK 04-May-15 Advanced Digital Communications, Spring-2015, Week-8 1 In-phase and Quadrature (I&Q) Representation Any bandpass
More information28. What is meant by repetition rate of the AM envelope? (ADC,AU-2010) 29. Describe the upper and lower sidebands. (ADC, AU-2010) 30.
Institute of Road and Transport Technology, Erode Department of Electronics and Communication Engineering Class/Sem: 2 nd Year Information Technology-3rd Semester Subject: Principles of Communication (IT)
More informationMobile & Wireless Networking. Lecture 2: Wireless Transmission (2/2)
192620010 Mobile & Wireless Networking Lecture 2: Wireless Transmission (2/2) [Schiller, Section 2.6 & 2.7] [Reader Part 1: OFDM: An architecture for the fourth generation] Geert Heijenk Outline of Lecture
More informationOverview of Digital Mobile Communications
Overview of Digital Mobile Communications Dong In Kim (dikim@ece.skku.ac.kr) Wireless Communications Lab 1 Outline Digital Communications Multiple Access Techniques Power Control for CDMA IMT-2000 System
More informationDescription of the AM Superheterodyne Radio Receiver
Superheterodyne AM Radio Receiver Since the inception of the AM radio, it spread widely due to its ease of use and more importantly, it low cost. The low cost of most AM radios sold in the market is due
More informationSPREAD SPECTRUM COMMUNICATIONS. historical and technical overview. Bryan Bergeron, NUlN 27 Stearns Road, Suite 8 Brookline. Massachusetts
Bryan Bergeron, NUlN 27 Stearns Road, Suite 8 Brookline. Massachusetts 02 146 SPREAD SPECTRUM COMMUNICATIONS historical and technical overview A s we all know, the RF spectrum is a finite and exceedingly
More informationAM and FM MODULATION Lecture 5&6
AM and FM MODULATION Lecture 5&6 Ir. Muhamad Asvial, MEng., PhD Center for Information and Communication Engineering Research Electrical Engineering Department University of Indonesia Kampus UI Depok,
More informationAngle Modulation. Frequency Modulation
Angle Modulation Contrast to AM Generalized sinusoid: v(t)=v max sin(ωt+φ) Instead of Varying V max, Vary (ωt+φ) Angle and Pulse Modulation - 1 Frequency Modulation Instantaneous Carrier Frequency f i
More informationANALOG AND DIGITAL COMMUNICATION DATA AND PULSE COMMUNICATION HISTORY OF DATA COMMUNICATION, STANDARDS ORGANIZATIONS FOR DATA COMMUNICATION.
UNIT III DATA AND PULSE COMMUNICATION 3.1 DATA COMMUNICATION: HISTORY OF DATA COMMUNICATION, STANDARDS ORGANIZATIONS FOR DATA COMMUNICATION. Data communication can be defined as two personal computers
More informationTechnician License Course Chapter 3 Types of Radios and Radio Circuits. Module 7
Technician License Course Chapter 3 Types of Radios and Radio Circuits Module 7 Radio Block Diagrams Radio Circuits can be shown as functional blocks connected together. Knowing the description of common
More informationPearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world
Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world Visit us on the World Wide Web at: www.pearsoned.co.uk Pearson Education Limited 2014
More informationMobile Communication An overview Lesson 03 Introduction to Modulation Methods
Mobile Communication An overview Lesson 03 Introduction to Modulation Methods Oxford University Press 2007. All rights reserved. 1 Modulation The process of varying one signal, called carrier, according
More information6. Modulation and Multiplexing Techniques
6. Modulation and Multiplexing Techniques The quality of analog transmission is S/N (signal to noise ratio). signal power S/N = ---------------------------- baseband noise power S/N can be greater than
More informationPart-I. Experiment 6:-Angle Modulation
Part-I Experiment 6:-Angle Modulation 1. Introduction 1.1 Objective This experiment deals with the basic performance of Angle Modulation - Phase Modulation (PM) and Frequency Modulation (FM). The student
More informationLecture 15: Introduction to Mixers
EECS 142 Lecture 15: Introduction to Mixers Prof. Ali M. Niknejad University of California, Berkeley Copyright c 2005 by Ali M. Niknejad A. M. Niknejad University of California, Berkeley EECS 142 Lecture
More informationCHETTINAD COLLEGE OF ENGINEERING & TECHNOLOGY NH-67, TRICHY MAIN ROAD, PULIYUR, C.F , KARUR DT.
CHETTINAD COLLEGE OF ENGINEERING & TECHNOLOGY NH-67, TRICHY MAIN ROAD, PULIYUR, C.F. 639 114, KARUR DT. DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING COURSE MATERIAL Subject Name: Analog & Digital
More informationEE390 Final Exam Fall Term 2002 Friday, December 13, 2002
Name Page 1 of 11 EE390 Final Exam Fall Term 2002 Friday, December 13, 2002 Notes 1. This is a 2 hour exam, starting at 9:00 am and ending at 11:00 am. The exam is worth a total of 50 marks, broken down
More informationDEPARTMENT OF COMPUTER GCE@Bodi_ SCIENCE GCE@Bodi_ AND ENIGNEERING GCE@Bodi_ GCE@Bodi_ GCE@Bodi_ Analog and Digital Communication GCE@Bodi_ DEPARTMENT OF CsE Subject Name: Analog and Digital Communication
More informationChapter 1. Overview. 1.1 Introduction
1 Chapter 1 Overview 1.1 Introduction The modulation of the intensity of optical waves has been extensively studied over the past few decades and forms the basis of almost all of the information applications
More informationCode No: R Set No. 1
Code No: R05220405 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2007 ANALOG COMMUNICATIONS ( Common to Electronics & Communication Engineering and Electronics & Telematics) Time: 3 hours
More informationFrequency Modulation KEEE343 Communication Theory Lecture #15, April 28, Prof. Young-Chai Ko
Frequency Modulation KEEE343 Communication Theory Lecture #15, April 28, 2011 Prof. Young-Chai Ko koyc@korea.ac.kr Summary Angle Modulation Properties of Angle Modulation Narrowband Frequency Modulation
More informationCS311: Data Communication. Transmission of Analog Signal - I
CS311: Data Communication Transmission of Analog Signal - I by Dr. Manas Khatua Assistant Professor Dept. of CSE IIT Jodhpur E-mail: manaskhatua@iitj.ac.in Web: http://home.iitj.ac.in/~manaskhatua http://manaskhatua.github.io/
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK 17 Product Application Notes Introduction
More informationANALOGUE TRANSMISSION OVER FADING CHANNELS
J.P. Linnartz EECS 290i handouts Spring 1993 ANALOGUE TRANSMISSION OVER FADING CHANNELS Amplitude modulation Various methods exist to transmit a baseband message m(t) using an RF carrier signal c(t) =
More information4.1 REPRESENTATION OF FM AND PM SIGNALS An angle-modulated signal generally can be written as
1 In frequency-modulation (FM) systems, the frequency of the carrier f c is changed by the message signal; in phase modulation (PM) systems, the phase of the carrier is changed according to the variations
More informationCommunication Channels
Communication Channels wires (PCB trace or conductor on IC) optical fiber (attenuation 4dB/km) broadcast TV (50 kw transmit) voice telephone line (under -9 dbm or 110 µw) walkie-talkie: 500 mw, 467 MHz
More informationOBJECTIVES EQUIPMENT LIST
1 Reception of Amplitude Modulated Signals AM Demodulation OBJECTIVES The purpose of this experiment is to show how the amplitude-modulated signals are demodulated to obtain the original signal. Also,
More informationObjectives. Presentation Outline. Digital Modulation Revision
Digital Modulation Revision Professor Richard Harris Objectives To identify the key points from the lecture material presented in the Digital Modulation section of this paper. What is in the examination
More informationI-Q transmission. Lecture 17
I-Q Transmission Lecture 7 I-Q transmission i Sending Digital Data Binary Phase Shift Keying (BPSK): sending binary data over a single frequency band Quadrature Phase Shift Keying (QPSK): sending twice
More informationDT Filters 2/19. Atousa Hajshirmohammadi, SFU
1/19 ENSC380 Lecture 23 Objectives: Signals and Systems Fourier Analysis: Discrete Time Filters Analog Communication Systems Double Sideband, Sub-pressed Carrier Modulation (DSBSC) Amplitude Modulation
More information4/29/2012. General Class Element 3 Course Presentation. Signals and Emissions. SignalSignals and Emissionsissions. Subelement G8
General Class Element 3 Course Presentation ti ELEMENT 3 SUB ELEMENTS General Licensing Class Subelement G8 Signals and Emissions 2 Exam Questions, 2 Groups G1 Commission s Rules G2 Operating Procedures
More informationPrepared for the Engineers of Samsung Electronics RF transmitter & power amplifier
Prepared for the Engineers of Samsung Electronics RF transmitter & power amplifier Changsik Yoo Dept. Electrical and Computer Engineering Hanyang University, Seoul, Korea 1 Wireless system market trends
More informationData Conversion Circuits & Modulation Techniques. Subhasish Chandra Assistant Professor Department of Physics Institute of Forensic Science, Nagpur
Data Conversion Circuits & Modulation Techniques Subhasish Chandra Assistant Professor Department of Physics Institute of Forensic Science, Nagpur Data Conversion Circuits 2 Digital systems are being used
More informationInternal Examination I Answer Key DEPARTMENT OF CSE & IT. Semester: III Max.Marks: 100
NH 67, Karur Trichy Highways, Puliyur C.F, 639 114 Karur District Internal Examination I Answer Key DEPARTMENT OF CSE & IT Branch & Section: II CSE & IT Date & Time: 06.08.15 & 3 Hours Semester: III Max.Marks:
More informationDHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY CS6304- ANALOG AND DIGITAL COMMUNICATION BE-CSE/IT SEMESTER III REGULATION 2013 Faculty
DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY CS6304- ANALOG AND DIGITAL COMMUNICATION BE-CSE/IT SEMESTER III REGULATION 2013 Faculty Name: S.Kalpana, AP/ECE QUESTION BANK UNIT I ANALOG
More informationAmplitude Modulation Fundamentals
3 chapter Amplitude Modulation Fundamentals In the modulation process, the baseband voice, video, or digital signal modifies another, higher-frequency signal called the carrier, which is usually a sine
More informationEE-4022 Experiment 2 Amplitude Modulation (AM)
EE-4022 MILWAUKEE SCHOOL OF ENGINEERING 2015 Page 2-1 Student objectives: EE-4022 Experiment 2 Amplitude Modulation (AM) In this experiment the student will use laboratory modules to implement operations
More informationCommunication Engineering Prof. Surendra Prasad Department of Electrical Engineering Indian Institute of Technology, Delhi
Communication Engineering Prof. Surendra Prasad Department of Electrical Engineering Indian Institute of Technology, Delhi Lecture - 16 Angle Modulation (Contd.) We will continue our discussion on Angle
More informationUNIVERSITY OF BAHRAIN COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONIC ENGINEERING
UNIVERSITY OF BAHRAIN COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONIC ENGINEERING EENG 373: DIGITAL COMMUNICATIONS EXPERIMENT NO. 5 BASEBAND MODULATION TECHIQUES Objective The main objectives
More informationA Modular Approach to Teaching Wireless Communications and Systems for ECET Students
A Modular Approach to Teaching Wireless Communications and Systems for ECET Students James Z. Zhang, Robert Adams, Kenneth Burbank Department of Engineering and Technology Western Carolina University,
More informationSignals and Systems Lecture 9 Communication Systems Frequency-Division Multiplexing and Frequency Modulation (FM)
Signals and Systems Lecture 9 Communication Systems Frequency-Division Multiplexing and Frequency Modulation (FM) April 11, 2008 Today s Topics 1. Frequency-division multiplexing 2. Frequency modulation
More informationUNIT 2 DIGITAL COMMUNICATION DIGITAL COMMUNICATION-Introduction The techniques used to modulate digital information so that it can be transmitted via microwave, satellite or down a cable pair is different
More informationThe Challenges of Precision Analog Modulation Measurement
The Challenges of Precision Analog Modulation Measurement Paul Roberts Fluke Precision Measurement Ltd Norwich, UK. +44 (0)1603 256781 paul.roberts@fluke.com Abstract - In today s digital world, many established
More informationOutline / Wireless Networks and Applications Lecture 3: Physical Layer Signals, Modulation, Multiplexing. Cartoon View 1 A Wave of Energy
Outline 18-452/18-750 Wireless Networks and Applications Lecture 3: Physical Layer Signals, Modulation, Multiplexing Peter Steenkiste Carnegie Mellon University Spring Semester 2017 http://www.cs.cmu.edu/~prs/wirelesss17/
More informationAMPLITUDE MODULATION
AMPLITUDE MODULATION PREPARATION...2 theory...3 depth of modulation...4 measurement of m... 5 spectrum... 5 other message shapes.... 5 other generation methods...6 EXPERIMENT...7 aligning the model...7
More informationRESEARCH ON METHODS FOR ANALYZING AND PROCESSING SIGNALS USED BY INTERCEPTION SYSTEMS WITH SPECIAL APPLICATIONS
Abstract of Doctorate Thesis RESEARCH ON METHODS FOR ANALYZING AND PROCESSING SIGNALS USED BY INTERCEPTION SYSTEMS WITH SPECIAL APPLICATIONS PhD Coordinator: Prof. Dr. Eng. Radu MUNTEANU Author: Radu MITRAN
More informationHam Radio Training. Level 1 Technician Level. Presented by Richard Bosch KJ4WBB
Ham Radio Training Level 1 Technician Level Presented by Richard Bosch KJ4WBB In this chapter, you ll learn about: What is a radio signal The characteristics of radio signals How modulation adds information
More informationModulation Methods Frequency Modulation
Modulation Methods Frequency Modulation William Sheets K2MQJ Rudolf F. Graf KA2CWL The use of frequency modulation (called FM) is another method of adding intelligence to a carrier signal. While simple
More informationDigital Communication System
Digital Communication System Purpose: communicate information at certain rate between geographically separated locations reliably (quality) Important point: rate, quality spectral bandwidth requirement
More informationLocal Oscillator Phase Noise and its effect on Receiver Performance C. John Grebenkemper
Watkins-Johnson Company Tech-notes Copyright 1981 Watkins-Johnson Company Vol. 8 No. 6 November/December 1981 Local Oscillator Phase Noise and its effect on Receiver Performance C. John Grebenkemper All
More information