installation guide ICON classic benching
|
|
- Gervais Gilmore
- 6 years ago
- Views:
Transcription
1 installation guide ICON classic benching
2 Index ICON Installation Guide Single Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame...6 Installing optional accessories...7 Installing Screens...8 Jumpers...9 Power Pole...0 Double Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame... Installing optional accessories... Installing Screens and Remaining Worksurfaces...6 Jumpers...7 Power Pole...8 Modesty Panel...9 P
3 ICON installation guide SINGLE RUN P
4 Phase Frame Assembly ICON Single Run Installation Guide Screw the outer-to-inner horizontal beams (H-bar) to the top of each outside leg (O-Leg) using the M8* screws. Then screw the outer-to-inner H-bars to the bottom of each O-Leg using the M6*0 screws. Adjust the glides to level the frame as needed. We suggest using a leveling glide for best accuracy. Rest the outer-to-inner H-bars on the top of the inner legs (U-Leg). Then rest the inner-to-inner H-bars on top the U-legs. Screw the horizontal beam connectors and H-bars to the frame using the M6*0 screws. Bottom screws should be installed first on all frame bars. NOTE: For 60 or 7 ICON frame bars the bars should be aligned so that the large oval hole is located on the inside of the bench to accommodate future returns. P
5 Phase Assembling Worksurfaces and Electrical ICON Single Run Installation Guide Lay the worksurfaces face down in a row. Screw the troughs onto all the worksurfaces using lath screws. It is recommended that troughs be placed in the center inches from the back edge of the worksurface. Snap duplexes into each of the junction blocks. Clip H-brackets to each of the junction blocks. Then snap the junction blocks into each of the trough cut outs. Screw the H-brackets directly into the troughs and worksurfaces using self-tappers. Place in center, from the back edge of the worksurface. P
6 Phase Attaching Worksurfaces to Frame ICON Single Run Installation Guide Rest the completed worksurfaces on top of the frame, starting from the outer worksurfaces working towards the center. Use a clamp to temporarily hold the worksurfaces together until they are ready to be permanently screwed to the frame. If needed, adjust the frame width to open or close the gap between the worksurfaces using a rubber mallet. 6 Screw all worksurfaces to the H-bars along the center of the frame using counter-sunk screws. Screw the worksurfaces together using a mending plate using counter-sunk screws. 6 Once everything is properly aligned, screw the outer worksurfaces to the frame using the counter-sunk screws. Make sure worksurfaces are evenly flush to the frame. P6
7 Phase Installing Optional Accessories ICON Single Run Installation Guide Power Box: Take the Power Box and place it on the desired location on the back edge of the worksurface. Secure to worksurface using tightening bolt. Monitor Arm Installation: We recommend to install a monitor arm equipped with clamp mount along the back edge of the worksurface. Please follow the recommended manufacturer instructions provided with your monitor arm. P7
8 Phase Installing Screens ICON Single Run Installation Guide STOP If you are installing a glass screen skip Step and continue on to Step. Take the fabric screens and measure the desired location of the screen clips and tighten using tightening screws. Be sure to use leveling guide to make sure the clips are leveled on each side. Make adjustments as needed. Skip Step and continue on to Step. * Clip kit includes fit-sleeve for glass screen. Insert glass fit-sleeve into the screen clips. Attach the clips to the glass screen with the tightening screws. Slide the screen clips onto the worksurface. Tighten to the worksurface using the hand-knob screw. To tighten screens, tighten the inside screw using an allen wrench. Fabric Screen Glass Screen P8
9 Phase 6 Installing Jumpers ICON Single Run Installation Guide Connect junction blocks to jumpers. Screw conduit mounting brackets to the worksurfaces using the counter-sunk screws STOP The remaining installation of electrical must be installed by a professional electrician. If you are installing a Power Pole continue on to Phase 7. P9
10 Phase 7 Installing a Power Pole ICON Single Run Installation Guide Make sure ceiling is prepped for the power pole location. You can use the ceilng cover as a guide to determine how big a cut out you need. Screw the power pole (pp) brackets to the top and bottom of the O-leg using self-tappers. Lay your pp on the floor and feed the ceiling feed through the bottom cutout of the pp. Loose wires should be at the top. Place the ceiling cover on the top of the pp. Lift the pp up and screw into pp brackets. Connect jumper to ceiling feed. Use the ceiling cover to secure pp to the ceiling. STOP The remaining installation of electrical must be installed by a professional electrician. * Use ceiling cover to secure pole to the ceiling. * Use self-tapping screw for attaching pole to leg beams. P0
11 Phase Frame Assembly ICON Single Run Installation Guide ICON installation guide DOUBLE RUN P
12 Phase Frame Assembly ICON Double Run Installation Guide Screw the outer-to-inner horizontal beams (H-bar) to the top of each outside leg (O-Leg) using the M8* screws. Then screw the outer-to-inner H-bars to the bottom of each O-Leg using the M6*0 screws. Rest the outer-to-inner H-bars on the top of the inner legs (U-Leg). Then rest the inner-to-inner H-bars on top the U-legs. Screw the horizontal beam connectors and H-bars to the frame using the M6*0 screws. Screw in the H-bar brackets to the U-legs using the M6* screws. Screw the round supports to the O-legs using the M6*0 screws. Adjust the glides to level the frame as needed. We suggest using a leveling glide for better accuracy. Bottom screws should be installed first on all frame bars. NOTE: For 60 or 7 ICON frame bars the bars should be aligned so that the large oval hole is located on the inside of the bench to accommodate future returns. P
13 Phase Assembling Worksurfaces and Electrical ICON Double Run Installation Guide Lay the worksurfaces face down in equal rows. Screw the troughs onto all the worksurfaces using lath screws. It is recommended that troughs be placed in the center inches from the back edge of the worksurface. Snap duplexes into each of the junction blocks. Clip H-brackets to each of the junction blocks. Then snap the junction blocks into each of the trough cut outs. Screw the H-brackets directly into the troughs and worksurfaces using self-tappers. P
14 Phase Attaching Worksurfaces to Frame ICON Double Run Installation Guide Rest the completed worksurfaces on top of one side of the frame, starting from the outer worksurfaces working towards the center. Use a clamp to temporarily hold the worksurfaces together until they are ready to be permanently screwed to the frame. If needed, adjust the frame width to open or close the gap between the worksurfaces using a rubber mallet. 6 7 Screw all worksurfaces to the H-bars along the center of the frame using counter-sunck screws. Screw the worksurfaces together using a mending plate using counter-sunk screws. Screw the worksurfaces to the H-braket located on the U-legs using the counter-sunk screws. 6 Once everything is properly aligned, screw the outer worksurfaces to the frame using the counter-sunk screws. Make sure worksurfaces are evenly flush to the frame. 7 Tip: Make sure H-bracket is inches from the back edge of the center worksurface to help ensure that the frame is straight. P
15 Phase Installing Optional Accessories ICON Double Run Installation Guide Power Box:Take the Power Box and place it on the desired location on the back edge of the worksurface. Secure to worksurface using tightening bolt. Monitor Arm Installation: We recommend to install a monitor arm equipped with clamp mount along the back edge of the workurface. Please follow the recommended manufacturer instructions provided with your monitor arm. P
16 Phase Installing Screens and Remaining Worksurfaces ICON Double Run Installation Guide STOP If you are installing a glass screen skip Step and continue on to Step. * Clip kit includes fit-sleeve for Glass screen. Take the fabric screens and measure the desired location of the screen clips and tighten using tightening screws. Be sure to use leveling guide to make sure the clips are leveled on each side. Make adjustments as needed. Skip Step and continue on to Step. Insert glass fit-sleeve into the screen clips. Attach the clips to the glass screen with the tightening screws. Slide the screen clips onto the worksurface. Tighten to the worksurface using the hand-knob screw. To tighten screens, tighten the inside screw using an allen wrench. Repeat Phase ; Steps -7 for installation of remaining worksurfaces. Fabric Screen Glass Screen P6
17 Phase 6 Installing Jumpers ICON Double Run Installation Guide Connect junction blocks to jumpers, looping the last jumper at the end of the run to connect to opposite side and continue. Screw conduit mounting brackets to the worksurfaces using the counter-sunk screws STOP The remaining installation of electrical must be installed by a professional electrician. If you are installing a Power Pole continue on to Phase 7. P7
18 Phase 7 Installing a Power Pole ICON Double Run Installation Guide Make sure ceiling is prepped for the power pole location. You can use the ceiling cover as a guide to determine how big a cut out you need. Screw the power pole (pp) brackets to the top and bottom of the O-leg using self-tappers. Lift the pp up and screw into pp brackets. STOP The remaining installation of electrical must be installed by a professional electrician. Lay your pp on the floor and feed the ceiling feed through the bottom cutout of the pp. Loose wires should be at the top. Place the ceiling cover on the top of the pp. Connect jumper to ceiling feed. Use the ceiling cover to secure pp to the ceiling. * Use ceiling cover to secure pole to the ceiling. * Use self-tapping screw for attaching pole to leg beams. P8
19 Phase ICON Modesty Panel Installation Guide Locate the four pilot holes on the board and attach four brackets using M wood screws. Place the assembly from previous step inside the leg s opened profile. Mx0 Self tapping screw x Using M self-tapping screws, attach the assembly onto the leg frame. Connector x pcs Mx Wood screw x Isle Side Leg side P9
20 Day Open Plan we provide exceptional experiences with reliable, easy interactions and successfully fulfilled orders in only days 9 Walsh Avenue / Santa Clara, CA 900 (877) amqsolutions.com
Footer & Base Plate Assembly. installation guide. ILINE power/data beam
Phase Footer & Base Plate Assembly installation guide ILINE power/data beam Phase Materials and Tools. ILINE Postsleeve Components Top Cap Data Face Plate Post Sleeve Post Sleeves shipped with orders after
More informationinstallation guide Footer & Base Plate Assembly KINEX Installation Guide SINGLE RUN
Phase Footer & Base Plate Assembly KINEX Installation Guide SINGLE RUN KINEXbenching installation guide Please contact cc@amqsolutions.com if you are missing any parts, have difficulty with assembly, or
More informationKINEX benching Installation Guide
KINEX benching Installation Guide Index KINEX Installation Guide SINGLE RUN SINGLE RUN Assembly Components... Assembly Outline...5 DOUBLE RUN Assembly Components...8 Assembly Outline...9 Assembly Instructions
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationAssembly Instructions & General Overview
Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.
More informationbridges Installation Manual
bridges Installation Manual 0 OHSAS 800:007 CGSB #0HS-009 ISO 900:008 CGSB #96- ISO 00:00 CGSB #EMS-00 Global Contract Inc. 6 Petrolia Road North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com
More informationSTAKS BENCHING ASSEMBLY INSTRUCTIONS
STAKS BENCHING ASSEMBLY INSTRUCTIONS TABLE OF CONTENTS BASE ASSEMBLY 3 ORGANIZER INSTALLATION 4-5 PRIVACY SCREEN INSTALLATION 6 WORKSURFACE INSTALLATION 7 TOP STRAP INSTALLATION 8-9 POWER INSTALLATION
More information13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS ALTERNATIVE
More informationTOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT
More information6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
More informationINSTALLATION MANUAL VERITY. friant.com/verity
INSTLLTION MNUL VERITY friant.com/verity 2 VERITY INSTLLTION MNUL General Information... 4 Safety & Support... 5 Installation Tools... 6 Staging & Installation... 7 Stand lone Units Single-Sided Structure...
More informationBridges II Installation Guide. Effective June 2017 DESIGN GUIDE
Bridges II Installation Guide Effective June 07 DESIGN GUIDE Structure and Worksurfaces Beam Applications Supporting Structure Legs and Beams Telescopic Beam 0 Leg Storage Table Beam Sliding Return Round
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationRANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions
INSTRUCTION SHEET #2577INS PART #1730534 DIGITAL HANDSET OPERATION OPERATION INSTRUCTIONS 1. Panel 1 Button: Preset 1 2 Button: Preset 2 3 Button: Preset 3 S Button: Select Display: Reads in 1 / 2 " Increments
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationCompile Installation Manual
Compile Installation Manual 07 OHSAS 800:007 ISO 900:05 ISO 400:05 Global Contract Inc. 565 Petrolia Road REVISED: FALL 07 North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com (46)
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationHover. Installation Instructions. Raised Panel. Version
Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31
More informationINSTALLATION MANUAL DASH. friant.com/dash
INSTALLATION MANUAL DASH friant.com/dash 2 DASH INSTALLATION MANUAL General Information... 4 Safety & Support... 5 Installation Tools... 6 Staging & Installation... 7 Tabletops Freestanding Tabletops...
More informationInterra Installation Manual
Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.
ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels
More informationAssembly Instructions. Table of Contents
HQ Little Foot Assembly Instructions Back of Handi Quilter, Inc. 501 North 400 West North Salt Lake, UT 84054 1-877-697-8458 Front of 2015 Handi Quilter, Inc. www.handiquilter.com Printed in the United
More informationTrendWall Floor-To-Ceiling Panels Installation Instruction
TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationSTAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS
STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.
More informationCastle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA
Castle Frame Assembly Table AT-8 Diagnostics Manual Castle, Inc. Petaluma, CA 800-282-8338 Solutions Index Adjusting the Tabletop.. 8.01 Adjusting the Fence... 8.02 Aligning the Arm... 8.10 Adjusting Bracket..
More informationACTIV Pro3 height adjustable base Installation Guide
ACTIV Pro height adjustable base Installation Guide Components ACTIV-Pro Installation Guide Hard ware cable clips x 8mm 5mm 4mm allen keys screw caps x 8 center leg x center leg bracket x end leg x foot
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationWorkbench Instructions for Assembly
Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...
More informationSeries 4 HV Single Monitor Lift Assembly Instructions
6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:
More informationContinuum Frame Assembly Instructions
Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii
More informationVideo Wall Installation Instructions 2W X 3H, 3W X 3H
Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...
More informationAngled Side Flush with Panel Face
Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationLead Screw Cover Installation
The premier source of tooling, parts, and accessories for bench top machinists. Lead Screw Cover Installation These instructions cover two products: 5201 Telescoping Lead Screw Cover, 7x10, 7x12 5202 Telescoping
More informationArt Rack Assembly Instructions:
Art Rack Assembly Instructions: ** PIECES ARE POWDER COATED Do not lay pieces on top of each other or on a hard, rough surface if possible. All bolts will pass from outside towards inside of the cage.
More informationPROFILE Flat Panel Console System Installation Manual
PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double
More informationMounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome
VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:
More informationPergola Installation Instructions
Pergola Installation Instructions TOOLS REQUIRED HAMMER DRILL 1/2 MASONRY BIT PENCIL DRILL 3/16 DRILL BIT LEVEL SQUARE LADDER WRATCHET & SOCKETS RUBBER MALLET 2 TAPE MEASURE Column/Post Placement Table
More informationGlass Front Sauna Room Assembly Manual
Glass Front Sauna Room Assembly Manual Classic Bench Version: 1.3 Note: Above images are for illustrative reference only and may differ from actual item. Parts List Exterior *For room with full glass wall
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationFlexFrame - Storage Components and Skins
FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General
More informationFord Pick Up Rear leaf Spring Kit Installation Instructions
1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4
More informationZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual.
ZAPF PANEL SYSTEM It is recommended that the components be installed in the sequence of this assembly manual. ASSEMBLY INSTRUCTIONS OFFICE FURNITURE FOR THE INFORMATION AGE Table of Contents INSTALLATION
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationRevised
Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationParts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece)
[1] - 23.5 x 35.5 Top [8] - Drawer Support Rods Parts List [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench [2] - Upper Base left End (1 pieces) [9] - Media Supports (1 pieces) [16] - loor Guides
More informationBoat Lift Canopy Frame Assembly Instructions
Patriot Docks Boat Lift Canopy Frame Assembly Instructions Helpful Tips: Assembling and installing the canopy frame and cover is a two person job. Additional help makes installation easier and is recommended.
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationSetup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.
Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a
More informationDeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)
Disclaimer: Deck Rail Glass Railing Installation Guide This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration purposes
More informationCommercial Wine & Liquor Display. Double Displays
Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display
More informationAssembly Instructions
Seminar Tables May 2014 Seminar Tables - Floor Anchor Specifications Floor Anchor Specifications 3 3/ 4 5 / 16 (4)½ diameter holes 3 1 / 4 2 4 8 #12.7503.KIT4 1 5 / 4 Hilti KH-EZ x 2 / 8 Max. Torque: 18
More informationNote: This assembly instruction will cover all configurations of Alloy adjustable height double bases.
Note: This assembly instruction will cover all configurations of adjustable height double bases. 1 Screw in the provided adjustable glides into each leg as shown in Figure A. Two glides per leg. Figure
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationLEGENDS RETRACTABLE DOOR SCREENS
I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess within the door jamb area. Recess installations are the most typically
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More informationHQ Studio Frame Two-Foot Section Assembly Instructions From Twelve-Foot to Ten-Foot
HQ Studio Frame Two-Foot Section Assembly Instructions From Twelve-Foot to Ten-Foot HQ Studio Frame Two-Foot Includes: Includes one (1) two-foot table frame with plastic top, two (2) two-foot track supports,
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationESA-200 Fixed Sidelite
Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationSpring Loaded All Season Roll-Up Doors
Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More informationHQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1
HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included
More informationGroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property.
GroundControl TM use supplied hardware Use only hardware supplied in your GroundControl kit or supplied by an authorized YAKIMA dealer. Use of unauthorized parts in the GroundControl system could result
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationLinear Hook- on Worksurfaces
Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep
More informationSawStop. T-GlideTM. Fence System- Professional Series II OWNER S MANUAL
SawStop T-GlideTM Fence System- Professional Series II OWNER S MANUAL Warranty SawStop warrants to the original retail purchaser of a new T-Glide Fence System - Professional Series II from an authorized
More informationEND FEED INSTALLATION
STARLINE PLUG-IN RACEWAY END FEED INSTALLATION The Universal End Feed (product numbers beginning with URPF, URDF, or MRPF, MRDF) provides the installer a provision to connect supply power to the Plug-In
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R
INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R I. SUSPENDED INSTALLATIONS 1. Lay the two track halves on the floor with
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More information