Installation Instructions
|
|
- Carmella Bennett
- 5 years ago
- Views:
Transcription
1 903-CIS0143-C Installation Instructions 0.9m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan 5B Telephone: SE GÖTEBORG SWEDEN
2 Unpacking Place antenna on a flat clean surface, such as on top of the packing material. Handle Antenn carefully at all times. Included parts Item Qty Description A 1 Radome Flat (Only 6, 7/8, GHz) B 1 Radome Spherical (Only 10/11 and GHz) C 1 Reflector D 1 Mounting Plate E 1 Bracket F 1 Antenna support (Box) 2 Clamp Bracket 1 Pipe Attachment Bracket 1 Pivot Bracket 2 Link Screw and Nut 5 M10x120 Screw 1 M10x40 Screw 3 M10x30 Screw 1 M8x16 Screw 7 M10 Nut G 1 Fasteners (Bag) 2 M10x35 Screw 1 M10x60Screw 8 M5x12 Torx 7 M4x16 Torx (Only 10/11 GHz) 7 M4x10 Torx (Only GHz) 7 M4 Washer (Only 10/11 and GHz) 7 M4 Clip (Only 10/11 and GHz) A B C Radome Flat Radome Spherical Reflector D E Mounting Plate Bracket 2(8)
3 F Link Screw and Nut (2x), M10x120 (5x), M10x40, M10x30 (3x), M8x16, M10 Nut (7x), Clamp Bracket (2x), Pipe Attachment Bracket and Pivot Bracket G M5x12 (8x) M4x16 (7x) M4x10 (7x) M4 Washer (7x) M4 Clip (7x) M10x60 M10x35 (2x) Tools required Screwdriver for Torx TX10, TX20 & TX25; for M3, M4 and M5. Allen key 6mm; for M8. Combination wrench (ring/open jaw) for Hex 15 & 16mm; for M10. Socket wrench and sockets for Hex 15 & 16mm; for M10. Tool for torque levels; 0.9Nm, 2.6Nm, 4.3Nm, 17Nm and 49Nm. 3(8)
4 Assembly Step 1 Reflector and Mounting Plate a) Place reflector on Mounting Plate. b) Align draining hole on the reflector to the draining hole on the Mounting Plate. c) Mount 8pcs M5x12 screws. d) Tighten the screws with 4,3Nm ± 5%. M5x12 Draining holes Step 2 Bracket For Right side installation the Bracket is installed on the right side and the antenna support is mounted upside down. Left side installation Right side installation a) Mount the Bracket with 2pcs M10x35. For left side installation mount the Bracket on the left side of the Mounting Plate and for right side installation mount the Bracket on right side of the Mounting Plate. b) Tighten the screws with 49Nm ± 5%. Bracket M10x35 4(8)
5 Step 3 Customer unique Installation For assembling of Feed and Adapter plates; follow customer unique Installation Instructions. Regarding assembly of vertex plates for 6GHz and 7/8GHz, follow steps below. Vertex plate assembly 6GHz a) Mount Vertex plate 2pcs with 2pcs of screws M3x10. b) Tighten the screws with 0,9Nm ± 5%. c) Mount Hat with 1pc of screw M3x10 and tighten it with 0,9Nm ± 5%. Vertex plates Hat M3x10 Vertex plate assembly 7/8GHz a) Mount Vertex plate 2pcs with 2pcs of screws M4x10. b) Tighten the screws with 2,6Nm ± 5%. Vertex plates M4x10 5(8)
6 Step 4 Radome Radome 6, 7/8 and 13-23GHz. a) Check that Vertex plates of Feed are mounted for 6 and 7/8 GHz antennas. b) Place Reflector into Radome and align one of the rotational stops on Radome with bottom cut out in Reflector edge. c) Mount Radome to Reflector. Check that the six hooks has snapped around the Reflector edge. d) Check that the second rotational stop on Radome is aligned with top cut out in Reflector. Rotations stop and cut out Radome 10/11 and 24-38GHz. e) Mount 7pcs M4 Clip to Reflector. f) Place Reflector into Radome and align holes in Radome to holes in Reflector. Use screwdriver or equivalent to align. g) Mount 7pcs M4x10 screws (or M4x16 for 10/11GHz) with washers, through Radome, into Reflector and M4 Clips. h) Tighten screws. M4 Washer M4 Clip M4 Screw 6(8)
7 Step 5 Antenna support. The following steps/pictures describe a left-side installation for right-side installation the bracket is mounted on the right side and the antenna support is mounted upside down. a) Mount M8x16 Screw to Bracket and tighten it with 17Nm ± 5%. M8x16 b) Mount Pivot Bracket to Bracket with M10x30, M10x60 and M10x40 screws. Tighten the screws. M10x30 Pivot Bracket M10x60 M10x40 c) Mount 2pcs M10 Link Screws with nuts to Pivot Bracket using 2pcs M10x30 screws. M10x30 Link screws M10 with Nuts M10x30 d) Mount 4pcs M10x120 screws to Pipe Attachment Bracket. M10x120 Pipe Attachment Bracket e) Mount Pipe Attachment Bracket to Pivot Bracket and Link screws using M10x120 screw and 3pcs M10 Nuts. Tighten the Nuts. M10x120 M10 Nuts Pivot Bracket Pipe Attachment Bracket 7(8)
8 f) Mount 2pcs Clamp Brackets and 4pcs M10 Nuts on 4pcs M10x120 screws. Clamp Brackets M10 Nuts g) Hoist and secure antenna to pole (Ø90- Ø120mm) using clamp brackets and nuts. h) Position the antenna so it will point along the radio link path. i) Tighten M10 nuts (4pcs) with 49Nm±5%. Antenna Alignment Elevation adjustment a) Slightly loosen Elevation lock screws. Use Elevation adjuster to adjust elevation ±15. Elevation lock screw M10x30 Elevation lock screw M10x60 Elevation lock screw M10x40 Elevation adjuster ±15 Azimuth adjustment b) Slightly loosen Hinge nut, Azimuth lock screw and azimuth nuts. Use Azimuth nuts on azimuth adjustment link screw to adjust azimuth ±15. Azimuth adjustment link screw ±15 (2pcs) Hinge nut Azimuth lock screw (2pcs) Azimuth nut (4pcs) ±15 c) Tighten all M10 screws (5pcs) and nuts (5pcs) with 49Nm ±5%. 8(8)
Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.
Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 2 ft Antennas (with M-Mount) SB, SBX (RFS CompactLine ) SP, SPF, SPX, SD, SDX, SU, SUX (RFS SlimLine ) PAL, DA, DAX, UA, UDA, UXA (Microwave) NMT 391-11(e) Antenna with integrated
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationInstallation Instructions
Installation Instructions For 0.2m Ultra-high Performance Antenna Model ADxxG-0-T2 Before Installation, please read these instructions carefully. This instruction guide is for the installation of 8 inch
More informationPole Mount Installation Guide
Pole Mount Installation Guide (No Fine Adjustment) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More informationThese Installation Instructions are valid for antennas in the following version:
Installation Instructions 4 ft CompactLine Antennas (with E-Mount 200 km/h) SB, SBX NMT 480-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall be
More informationRemarks: Before Installation, please read the instruction carefully.
30 cm antenna Z24A30T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.3m ultra-high performance microwave antenna. Installation,
More informationRemarks: Before Installation, please read the instruction carefully.
60 cm antenna Z24A60T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.6m ultra-high performance microwave antenna. Installation,
More informationInstallation Instructions
Installation Instructions Feed Installation for 0.6m(2ft) Spread Spectrum Antennas Bulletin 239851 Revision F Antenna Assembly Sequence P2F/HP2F/PX2F/ HPX2F antenna 1 2 3 1a 1 Apply conductive grease (5)
More information2 Pipe Clamp Bracket 3 11 M6 Screw with Tube M6 Hex Nut 2 4 M20 Flat Washer 4
3842 Revision B, May 201 Mounting Kit, For Metro Cell Antennas MC-MNT-TOP-2 Mounting Kit GENERAL INFORMATION Top of pole mounting option Fits round members.3" to 8." (10 to 21 mm) pole diameter. PRE-INSTALLATION
More informationInstallation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX
Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX NMT 553-01(e) These Installation Instructions are valid for antennas in the following version : Reflector Ø
More informationInstallation Guide Flat Panel Antenna Mounting Kit For
Installation Guide Flat Panel Antenna Mounting Kit For 103670-1 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com
More informationANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain
ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationStandard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)
495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions
More informationInstallation Guide. 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD
Installation Guide 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD Contents Introduction 1 Specifications 1 Safety Notice 2 Package Contents 2 Installation Requirements 3 Hardware Overview 3 Hardware
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationMITCHELL WREATH RINGS NO-HAMMER ASSEMBLY INSTRUCTIONS
MITCHELL WREATH RINGS NO-HAMMER ASSEMBLY INSTRUCTIONS METAL STAND WITH WOOD STAND WITH PAGE 2 OF 10 MASTER PARTS LIST HEAD ASSEMBLY LINKAGE ASSEMBLY HOOK LEVER ASSEMBLY FOOT PEDAL ASSEMBLY ALL FASTENERS
More informationInstallation Guide For FPD Antenna
Installation Guide For 104590-1 FPD.5-5.8-18 Antenna 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationPFD-22 Top OHC Patch Fitting & PFD-10 Bottom Patch Fitting Installation Instructions
Top OHC Patch Fitting & Bottom Patch Fitting Installation Instructions For Installation Assistance, Call 855.594.6989 www.assaabloyglass.us Tools Needed: Torque Wrench and Bit 5mm Allen Wrench 6 7 /16"
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Plus Antenna These instructions will lead you
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationRZR 4 Doors Part # Polaris RZR XP & Turbo ( ) Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com RZR 4 Doors Part # 07-1802 Polaris RZR XP 4 1000 & Turbo (2015-2018) Black Revision No: 01 Revision Date:
More information1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More information75 cm ODU (VS1300) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly Transport On Site Assembly This Job Aid supports all Technician audiences. This job aid covers the VS1200 ODU
More informationInstallation Instructions
Articulating Dual Monitor Mount Stand Installation Instructions UNPACKING Carefully open the carton, remove contents, and place them on a protected surface to avoid damage. Check the parts and the Supplied
More information**MOUNTING YOUR MONITOR
FPP72V200 72 FREE STANDING DISPLAY CART Assembly Instructions Hardware List Ref. Qty. Part No. Description AA 4 030-1128 1/4-20 UNC, 1 3/4 Socket Hd Screws BB 1 030-1129 5/8-11 UNC 1 3/4 Socket Hd Screw
More informationProjector Ceiling Mount
INSTALLATION MANUAL Projector Ceiling Mount PID:3010 PID:5466 20kg (44lbs) RATED CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! ISSUED: FEB. 2013 NOTE: Read the
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationM2 Antenna Systems, Inc. Model No:
M2 Antenna Systems, Inc. Model No: 400-600-10 SPECIFICATIONS: Model... 400-600-10 Frequency Range... 390 To 650 MHz *Gain... 12 To 13 dbic Front to back... 20 db Nominal Beamwidth... 46 Nominal Feed Impedance....
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationTV Floor Cart and Accessories
11. Adjustment INSTALLATION MANUAL Flo Cart and Accessies Loosen the knobs to adjust the display to the desired angle and tighten the knobs to secure. +5 /-12 + - + - 1200mm 1250mm 1300mm 1350mm 1400mm
More information1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM
August12, 2003 ASSEMBLY MANUAL Revision E 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM E Revised
More informationDO35 MAINTENANCE INSTRUCTIONS
CUSTOMER INFORMATION SHEET NO. 038 DO35 MAINTENANCE INSTRUCTIONS (DO35 V3 LAUNCHED PRODUCTION JUNE 2017) Table of Contents 1.0 Replacing Spindle Bushes V3... 22 2.0 Replacing Locking Mechanism V3... 6
More informationCable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench
Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -
More informationINSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT
INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More information75 cm ODU (VS1300 with the SurfBeam2 TRIA) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly TRIA, TRIA Bracket, and Boom Arm Assembly This Job Aid supports all Technician audiences. This job aid covers
More informationINSTALLATION GUIDE NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum )
INSTALLATION GUIDE 1530-NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Ladder Rack Assembly... 3-5 5-13 Phase 2 - Installation q
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Ultra Antenna These instructions will lead
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationINSTALLATION GUIDE Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum )
INSTALLATION GUIDE 7115 Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Locker w/ Top Shelf Assembly... 3-5 6-13 Phase
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationInstructions and Parts List DR-12N Martin House
Form 36-99 Instructions and Parts List DR-N Martin House Note: It is necessary to install a post before house is put up, but the house can be assembled at any time. House parts Check parts against this
More informationELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D
ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More information1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM
REVISION H April 20, 2016 ASSEMBLY MANUAL 1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 1.2
More informationSTOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets
Rev. 04 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS S-Type Network Cabinets -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench
More informationmounting instruction plateau #177 #177 Plateau - mounting out-sider a/s Kigkurren 8A, Islands Brygge DK-2300 Copenhagen S
mounting plateau instruction #177 Index: page Parts included for mounting: Unpacking the shipment...03 Preparations for mounting the legs...04 Legs mounting, step 1...05 Legs mounting, step 2...06 Legs
More informationBOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions
BOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions Contents of BOX-115 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Passenger Side b (1 ea.) Utility Box Support
More informationBefore use please read & understand this manual, paying particular attention to the safety instructions.
OPERATOR S MANUAL AND PARTS LIST 12 HAND PUSH ROLLER MOWER - THHMR Sales & Helpline 01793 333220 www.thehandy.co.uk Before use please read & understand this manual, paying particular attention to the safety
More informationB B B
Winchester SXP Gauge Tactlite Six Position Adjustable Shotgun Stock with Scorpion Recoil System B..0.00 B..0.00 B..0.00 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3358-2 PCN 060712-5 Side-of-Pole Mount for 4 Modules (SPM4) For
More information40993 Parts List. Front Bow Assy.(1) Rear Bow Assy.(1)
40993 Parts List Front Bow Assy.(1) Rear Bow Assy.(1) Rail Mnt Foot(4) Ladder Hook (2) Ladder Stop (2) Mounting Clip-ProMaster Only (6) Mounting Bracket(6) Long Mounting Rail(2) Short Mounting Rail(2)
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationFlat Panel Mobile Cart and Accessories
INSTALLATION MANUAL Flat Panel Mobile Cart and Accessories Optional Accessories TCH01 TDV01 TLP01 TCR01 Note: The accessories are not standard. The accessories will be selected according to user requirement.
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationKIT ASSEMBLY INSTRUCTIONS
JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds
More informationCode Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7
List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Holden VE Ute 2007
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Holden VE Ute 007 Part Number: EGR-PVE-UNP Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationSEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions
SEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions Contents of SEAT-361 RHOX 300 Series Rear Seat Kit: a (1 ea.) Front Seat Back Support, Driver Side b (1 ea.) Front Seat Back Support, Passenger
More informationRemoving the Z-Axis lead screw
Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains
More informationFull-motion Wall Mount
Full-motion Wall Mount MD120409-01 AWM1521- AU Safety Instruction Component Checklist WARNING IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing.
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationHITCH MOUNT BICYCLE CARRIER Model BC-102
HITCH MOUNT BICYCLE CARRIER Model BC-102 MAXIMUM LOADING CAPACITY 60 LBS Recommended Tools for Assembly: Open Wrench (2 pc.) Open Wrench (2 pc.) Open Wrench (2 pc.) Size=17mm Size=19mm Size=24mm Assembly
More informationINSTALLATION INSTRUCTIONS 1PC FRONT BUMPER JEEP JK WRANGLER
INSTALLATION INSTRUCTIONS PARTS LIST: 1 1PC Bumper 2 8mm x 25mm Hex Bolts 1 Bull Nose Hoop 2 8mm x 16mm Hex Bolts 1 Fairlead Mounting Bracket 6 8mm x 24mm x 2mm Flat Washers 8 12mm x 35mm Hex Bolts 4 8mm
More informationINSTALLATION INSTRUCTIONS ATV Winch Mounting Kit Part Number: Applications: Honda Rancher. Before You Begin.
INSTALLATION INSTRUCTIONS ATV Winch Mounting Kit Part Number: 68852 Applications: 2000+ Honda Rancher As you read these instructions, you will see NOTES, CAUTIONS, and WARNINGS. Each message has a specific
More informationINSTALLATION INSTRUCTIONS UTV LIGHT BAR KIT Part Number: and Application: All UTV s*
INSTALLATION INSTRUCTIONS UTV LIGHT BAR KIT Part Number: 83970 and 84360 Application: All UTV s* * does not include Arctic Cat vehicles Your safety, and the safety of others, is very important. To help
More informationABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SELF LEVELING RADAR ANTENNA MOUNT MODEL 400G QUESTUS MARINE, INC. PO BOX 9 MARBLEHEAD, MA 01945 1-800-RADAR66 TEL 781.639.1900 FAX 781.639.1905 www.questusmarine.com INSTALLATION
More informationFABRICATOR 211i & 252i ROLL CAGE ASSEMBLY INSTRUCTIONS
Manual 0-5233 Manufacturer: Thermadyne Industries Address: 82 Benning Street West Lebanon, New Hampshire 03784 USA Telephone: 1-800-426-1888 Fax: 1-800-535-0557 Email: sales@thermalarc.com www.thermalarc.com
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationcontained within this bulletin must always be followed and take precedence over any information contained within the video
Rev: K IMPORTANT! INSTALLATION READ THIS MANUAL FULLY BEFORE UNPACKING AND ASSEMBLING ANTENNA 1ft 2ft Videos provide supplementary information - the instructions contained within this bulletin must always
More informationArticulating TV/Monitor Grommet/Clamp Desk Mount Model: DE300S (Butterfly Series)
t Articulating TV/Monitor Grommet/Clamp Desk Mount Model: DE300S (Butterfly Series) Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct
More informationMODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible
More information74CM KU-BAND TYPE 741 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount
JULY 2016 Revision A ASSEMBLY MANUAL 8001114-01 74CM KU-BAND TYPE 741 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount A ORIGINAL RELEASE - EC-02522 JUL 2016 R. Thompson REV. DESCRIPTION DATE
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationInstallation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS
Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand
More informationBOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions
BOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions Contents of BOX-117 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationBOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions
BOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions Contents of BOX-118 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More information