TV Floor Cart and Accessories

Size: px

Start display at page:

Download "TV Floor Cart and Accessories"

Hubert Barnett
5 years ago
Views:

1 11. Adjustment INSTALLATION MANUAL Flo Cart and Accessies Loosen the knobs to adjust the display to the desired angle and tighten the knobs to secure. +5 / mm 1250mm 1300mm 1350mm 1400mm 1450mm 1500mm 1550mm 1600mm Display panel center height measured from flo. CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJUR OR PROPERT DAMAGE MA OCCUR! Maintenance Check that the bracket is secure and safe to use at regular intervals(at least every three months). Please contact your distribut if you have any questions. 200x x300 S21 400x200 70" 400x x400 MAX 50kg (110lbs) RATED DVD 5kg (11lbs) RATED CAMERA 5kg (11lbs) RATED

2 NOTE: Read the entire instruction manual befe you start installation and assembly. WARNING Component IMPORTANT: Ensure Checklist that you have received all parts accding to the component checklist pri to installation. If any parts are missing faulty, telephone your local distribut f a replacement. T04-44TW/46TW Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions warnings, please contact your local distribut. This mounting bracket was designed to be installed and utilised ONL as specified in this manual. Improper installation of this product may cause damage serious injury. middle base (x1) A left leg (x1) B right leg (x1) C left cover (x1) D right cover(x1) E Always use an assistant mechanical lifting equipment to safely lift and position the equipment. suppt plate (x1) F universal plate (x1) G plastic cover (x2) H adapter bracket (x2) I Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. This product is intended f indo use only. Using this product outdos could lead to product failure and personal injury. column (x1) J plastic handle (x1) K top cover (x1) L connecting plate (x1) M camera shelf (x1) N DVD shelf (x1) O washer (x4) P M6x16 (x8) Q M6x25 (x2) R M4x6 (x3) S M4x6 (x4) T M6x14 (x2) U M6x8 (x6) V M8x25 (x4) W M5x8 (x2) X Allen key (x1) wrench (x1) Z Package M M5x14 (x4) M-A M6x14 (x4) M-B M8x20 (x4) M-C M6x30 (x4) M-D M8x30 (x4) M-E washer (x4) small spacer (x8) big spacer (x4) M-H 1 2

3 1. Assembling the Base K Z Q Insert the right leg into the base. Align the holes in the right leg to the holes in the base. Secure with the screws. Repeat this step f the left leg. Each cast can be adjusted independently f fine tuning. Slightly turn the nut to lower raise the base. 2. Attaching the Column to the Base W CAUTION: Please hold the inner column when loosening the screws to adjust height. Attach the column to the base using the screws.tighten all screws using an Allen key. E D Adjust to the desired height, then tighten all screws. 3 4

4 3. Installing the Suppt Plate L H U V F Attach the suppt plate to the column with the screws. Tighten all screws using a suitable screwdriver. 4. Installing the Adapter Brackets P Insert the washers into the back of universal plate along the plate rails. I Attach the two plastic covers to both ends of the plate using the appropriate screws. Tighten all screw using a suitable screwdriver. min200mm-max400mm min200mm-max600mm Insert the adapter brackets into the universal plate. Align the holes in the adapter brackets to the holes in the washers. Insert the four screws but do not tighten them yet. Q 5 Adjust the adapter brackets to fit the hole pattern of your display. Then tighten all screws with an Allen key. NOTE: Verify the proper alignment of all holes. 6

5 5. Hooking the Display onto the Suppt Plate 4-1 F Flat Back Screens M-A/M-B/M-C X Hook the universal plate onto the suppt plate. Tighten two screws to secure them. IMPORTANT: Make sure the display is mounted crectly, and that the screws are tightened safely befe releasing the display. 4-2 F Recessed Back Screens to Access A/V Inputs 6. Installing the DVD Shelf plastic holder lever Insert the two plastic holders of the DVD shelf into the slots and close the lever to lock the DVD shelf. M-C / M-D/M-E M-C M-D/M-E M-D/M-E M-H M-H Note: Choose the appropriate screws, washers and spacers (if necessary) accding to the type of screen. Screw the adapter brackets onto the display. T Tighten two screws to secure. Tighten all screws but do not over tighten. 7 8

6 9. Installing the Connecting Plate 7. Cable Management R Attach the connecting plate to the column at the desired height using the appropriate screws. Tighten all screws using a suitable screwdriver. 10. Display Orientation V 8. Installing the Camera Shelf S T A: F Landscape View Attach the camera shelf to the connecting plate using the appropriate screws. Tighten all screws using a suitable screwdriver. 9 B: F Ptrait View Install at least two screws diagonally to secure the display. Remove the two screws to rotate the display 90 clockwise, then retighten the removed two screws into the different hole position to secure the display. 10

Full Motion LED, LCD TV Wall Mount

Full Motion LED, LCD TV Wall Mount 8. Adjustment INSTALLATION MANUAL Full Motion LED, LCD Wall Mount 120 +15-15 +5-5 CAUTION: DO NOT ECEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! Adjust to the desired location