Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX
|
|
- Calvin Whitehead
- 5 years ago
- Views:
Transcription
1 Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX NMT (e) These Installation Instructions are valid for antennas in the following version : Reflector Ø 1.2 m (4 ft) Single or Dual polarization Pipe mount for installation on pipe Ø 114 mm Antenna offset to the left or to the right Standard installation on 114 mm pipe with offset to the left Safety collar for easy installation 2 spindles for fine adjustment of Elevation of ± 15 and Azimuth ± 5 Reflector with shroud, shroud aperture covered by a flexible radome 200 km/h version : With sway bar Ø 27 mm x 1.35 m (mandatory) It is important to mount the antenna exactly as described in this installation instruction. The installed antenna shall be inspected once per year by qualified personnel. RFS disclaims any responsibility for the result of improper or unsafe installation. This installation instruction has been written for qualified, skilled personnel. We reserve the right to alter details, especially with respect to technical improvement. Sales department : Radio Frequency Systems GmbH Kabelkamp 20, D Hannover (Germany) Tel Fax Plant: RFS France Trignac Fax /10
2 1. Tools required for installation (Tools are not included with antenna) Hoisting device for 100 dan Torque wrench from 0 to 50 Nm Wrenches for hexagon bolts : M5(8), M6(10), M8(13), M10(17) Shackle(s), roll(s), pulley(s) and lifting accessories 2 strong ropes (approx. Length 1.5x tower high) 1 strong rope or cable (approx. Length 2.5x tower high) Water balance, compass, cutter, tape measure Key for socket screw : M3(2.5) (values in brackets=openings of spanners) 2. Antenna Offset (Overview) Reflector TOP mark aligned with antenna TOP Offset left Drain holes of the shroud towards the antenna bottom Holes for feed systems equipped with guy wires Offset right Drain holes of the shroud towards the antenna bottom Rotate the reflector and the tower mount 180 Reflector TOP mark aligned with antenna BOTTOM NMT e 2/10
3 3. Pre-assembly of the mount For easy operation of the bolted joints, and correct torque tightening, «Anti Seize» Installation Paste must be applied to all threads of bolts and fine adjustment spindles. After this, keep the lubricated threads free of dust and dirt! (a Torque Table is attached for specifications) 3.1 Install the reflector front side facing ground on the packing cover. (Do not lean on the reflector during the assembly, the reflector geométry may be permanently damage, and degrade antenna performances). 3.2 Connecting Support Mount screws M8x25 4 SL washers A8 4 nuts M SL screws M10x25 2 washers 10.5 Ø Steel U-Mount 4 ft Do not install the Elevation Spindle yet, it may be damage during shroud assembly on the reflector NMT e 3/10
4 4. Assembly of the shroud 4.1 Reflector orientation depending of the antenna offset For an antenna installation Offset Left Loosen the M6 bolted shroud junction (preassembled in factory) Shroud 23 screws M6x16 46 washers sl nuts M6 The free hole located at the shroud junction must be aligned with the hole facing the reflector TOP mark At the 2 holes 90 from TOP reflector mark 2 screws M6x16 4 washers serrated lock washers sl nuts M6 For an antenna installation Offset Right Reflector TOP mark in opposition with the shroud junction (Note : the TOP mark is visible on the outer face of the reflector). The free hole at the shroud junction must be aligned with the hole facing the reflector TOP mark Shroud Loosen the M6 bolted joint of the shroud junction (pre-assembled in factory) Reflector TOP mark in opposition with the shroud junction (Note : the TOP mark is visible on the outer face of the reflector). 23 screws M6x16 46 washers sl nuts M6 At the 2 holes 90 from TOP reflector mark 2 screws M6x16 4 washers serrated lock washers sl nuts M6 NMT e 4/10
5 5. Feed Installation* (See feed Installation Instructions joined) For the following antenna freq. codes, you must install the feed system before the assembly of the radome on the shroud : - Guy wires staying system (Monopolar. & Dualpolar. Freq. Codes > 100) - Mixed mounting feed systems with tuning plate Ø > 120 mm (Monopolar. F = 77, 78) - Mixed mounting feed systems (Monopolar. Freq. codes = 34, 36, 56, 57, W57, 59, 65) *If your feed system is not concerned skip this step, you can install it subsequently at chapter Assembly of the radome (for antennas without shroud skip this step) Front Rear 12 screws M6x25 12 washers mm 12 washers sl nuts M6 Radome Shroud rim - If the feed system has been installed, hold the antenna on the reflector rim by a personnel to avoid feed access damage or deformation. (if your feed system is not installed you can turn carefully the antenna to install it on the mount as shown below). - Position the radome over the shroud - Fix the radome with 4 screws handtight every 90 around the circumference - Fix the remaining screws and handtighten - Tighten all screws Antenna orientation when feed system is not yet installed Antenna orientation when feed system is already installed (to avoid feed access damage) 7. Feed Installation Refer to Feed Installation Instructions joined. NMT e 5/10
6 8. Elevation Spindle installation ELEVATION fine adjustment Spindle M10x100 2 brass nuts M10 2 washers 10.5 Elevation spindle installed 9. Azimuth safety collar installation on pipe support Note that the installation of the antenna should be accomplished by qualified personnels, and well trained person in fair climatic conditions (In any case, always respect the safety regulation in effect in the country). Activities involving the use of pulleys, ropes, carabiners and others accessories to hoist antennas and associated products are inherently dangerous. You are responsible for your own actions and decisions. The use of hoisting systems must be done by qualified and skilled personnel. Always use certified and controlled equipments, and be sure to respect the breaking load and the working load limit of each element (pulleys, ropes, carabiners ). RFS disclaims any responsibility in case of non repect of these warnings.. For an installation Offset Left V-bolt M10 2 washers 10.5 Ø30 4 nuts M10 (Take care of the clamp orientation) Minimum free space on pipe above V-Bolt 345 mm Minimum free space on pipe under V-bolt 35 mm For an installation Offset Right Minimum free space on pipe above V-Bolt 345 mm V-bolt M10 2 washers 10.5 Ø30 4 nuts M10 (Take care of the clamp orientation) Minimum free space on pipe under V-bolt 35 mm NMT e 6/10
7 10. Lifting of the antenna & hoisting on the tower (Feed system not shown) Strong rope attached on the reflector casting eye (Ø8.5 mm) with a shackle, and linked to winch Shackle Shackle Steel mount Principle for an installation with a left offset Strong rope fixed at the tower top. The rope is slipping through a steel roll or a shackle, which is fixed on the reflector casting eye (Ø8.5 mm) To winch Strong rope or cable fixed to antenna steel mount to avoid collision with the tower structure during hoisting NMT e 7/10
8 11. Antenna installation on pipe (Feed system not shown) 2 V-Bolts M10 4 washers nuts M10 Antenna installation over the pre-installed azimuth safety collar. Do not forget to apply «Anti Seize» installation paste on V-Bolt threads. It will insure a correct tension for the final V-Bolts torque tightening. 12. Azimuth fine adjustment spindle installation Principle for an installation with a left offset Eye spindle M10x130 2 washers brass nuts M10 Screw M10x30 Washer 10.5 SL nuts M10 NMT e 8/10
9 13. Elevation fine adjustment (Feed system not shown) Torque tighten the 2 M10 screws (refer to torque table joined), then loosen it, ¼ turn Principle for an installation with a left offset Loosen or tighten M10 brass nuts to adjust the Elevation After complete elevation fine adjustment, torque tighten the 2 M10 screws 14. Azimuth fine adjustment (Feed system not shown) Loosen M10 nuts of the 2 V-Bolts Principle for an installation with a left offset Loosen or tighten M10 brass nuts to adjust the Azimuth. After complete Azimuth fine adjustment, lock each first nut of the V-bolts (greased) at the specific torque, (refer to torque table joined) then tighten the second nut against the first one using usual wrench (do not use 2 wrenches to fix the second nut). Then tighten the 2 brass nuts M10 of the Azimuth spindle. NMT e 9/10
10 15. Sway bar pre-assembly Typical configuration for direct mount on angle tower structure Fixing plate Sway bar 2 U-bolts M6/27 8 nuts M6 4 washers 6.4 SL nut M10 Washer 10.5 Screw M10x30 2 SL nuts M10 2 washers screws M10x30 Configuration with Kit : SMA-SKO (sway bar kit option for install on pipe structure tower) SL nut M10 Washer 10.5 Screw M10x Sway bar installation (Feed system not shown) For convenience the fixation of the sway bar on the tower structure must be done after complete fine Azimuth & Elevation antenna alignment. Installation on the antenna Sway bar orientation Antenna casting ring Sway bar clamp SL Nut M10 Washer 10.5 Screw M10x25 SL washer A10 Screw M10x25 After sway bar positioning torque tighten all bolted joints ±25 max 17. Final Check When the installation of the antenna has been completed, it is necessary to make sure that the installation instructions have been followed in all aspects. It is especially important to check that all bolted joints have been greased and are torque tightly locked. NMT e 10/10
These Installation Instructions are valid for antennas in the following version:
Installation Instructions 4 ft CompactLine Antennas (with E-Mount 200 km/h) SB, SBX NMT 480-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall be
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 2 ft Antennas (with M-Mount) SB, SBX (RFS CompactLine ) SP, SPF, SPX, SD, SDX, SU, SUX (RFS SlimLine ) PAL, DA, DAX, UA, UDA, UXA (Microwave) NMT 391-11(e) Antenna with integrated
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationInstallation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.
Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationInstallation Instructions
903-CIS0143-C Installation Instructions 0.9m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan
More informationANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain
ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance
More informationInstallation Instructions
Installation Instructions Feed Installation for 0.6m(2ft) Spread Spectrum Antennas Bulletin 239851 Revision F Antenna Assembly Sequence P2F/HP2F/PX2F/ HPX2F antenna 1 2 3 1a 1 Apply conductive grease (5)
More informationRemarks: Before Installation, please read the instruction carefully.
30 cm antenna Z24A30T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.3m ultra-high performance microwave antenna. Installation,
More informationRemarks: Before Installation, please read the instruction carefully.
60 cm antenna Z24A60T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.6m ultra-high performance microwave antenna. Installation,
More informationStandard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)
495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions
More informationAntenna Installation Manual
High Performance Antennas 3 & 4 ft. (0.9 & 1.2 m) Antenna Installation Manual Please read the manual completely and carefully before installation. Instructions are intended for qualified and experienced
More informationInstallation Instructions
Installation Instructions For 0.2m Ultra-high Performance Antenna Model ADxxG-0-T2 Before Installation, please read these instructions carefully. This instruction guide is for the installation of 8 inch
More informationPole Mount Installation Guide
Pole Mount Installation Guide (No Fine Adjustment) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More informationInstallation Guide Flat Panel Antenna Mounting Kit For
Installation Guide Flat Panel Antenna Mounting Kit For 103670-1 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com
More informationE4-WM5-Y542A00 MOUNTING INSTRUCTION
This instruction is for both left front (driver) 41-269282 and right front (passenger) 41-269299 B8 8112 shocks. A step by step process is shown with images of the right front. The left front is a mirror
More informationDO35 MAINTENANCE INSTRUCTIONS
CUSTOMER INFORMATION SHEET NO. 038 DO35 MAINTENANCE INSTRUCTIONS (DO35 V3 LAUNCHED PRODUCTION JUNE 2017) Table of Contents 1.0 Replacing Spindle Bushes V3... 22 2.0 Replacing Locking Mechanism V3... 6
More informationImportant Notice. caution: Use proper lifting equipment and correct procedures to avoid injury.
Integrity. Partnership. Quality. COMMERCIAL DOOR INSTALLATION INSTRUCTIONS SERIES 1900, 1950, 2000, 2250, 2500, 2750 Important Notice In the following text, the word: Warning: Indicates that serious injury
More information1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM
REVISION H April 20, 2016 ASSEMBLY MANUAL 1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 1.2
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
Frequency Range Dual Polarization HPB Adjust. Electr. DT 698 960 1710 2690 1710 2690 1.5 10 0 10 2 10 set by hand or by optional RCU (Remote Control Unit) X X 65 65 65 X 6-Port Antenna 698 960/1710 2690/1710
More informationRemoving the Z-Axis lead screw
Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
Frequency Range Dual Polarization HPB Adjust. Electr. DT 698 960 1710 2690 1710 2690 1 12 2 12 2 12 set by hand or by optional RCU (Remote Control Unit) X X 65 65 65 X 6-Port Antenna 698 960/1710 2690/1710
More informationINSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT
INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS
More information8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 B1 1710 1880 B2 1920 2170 Y1 2490 2690 X X X X 65 65 65 65 0.5 9.5 2 8 2 8 2 8 set by hand or by optional RCU (Remote Control Unit) 8-Port
More informationInstallation Guide. 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD
Installation Guide 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD Contents Introduction 1 Specifications 1 Safety Notice 2 Package Contents 2 Installation Requirements 3 Hardware Overview 3 Hardware
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 698 960 Y1 1710 2690 1.5 10 2 8 set by hand or by optional RCU (Remote Control Unit) X 65 X 65 4-Port Antenna 698 960/1710 2690 65 /65 17/18.5dBi
More information2 Pipe Clamp Bracket 3 11 M6 Screw with Tube M6 Hex Nut 2 4 M20 Flat Washer 4
3842 Revision B, May 201 Mounting Kit, For Metro Cell Antennas MC-MNT-TOP-2 Mounting Kit GENERAL INFORMATION Top of pole mounting option Fits round members.3" to 8." (10 to 21 mm) pole diameter. PRE-INSTALLATION
More informationThread protection accessories are installed at the MODIX production factory and delivered with couplers.
Installation of MODIX Rebar Coupler Identification of the product The type of MODIX Rebar Coupler can be identified by the marking on the product. Size of the Coupler can be identified also according to
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007-2010 CHEVY/GMC SILVERADO/SIERRA 2500/3500 (EXCLUDES CLASSIC) APP PART #46-23715, 40-92315/45-92310 MAX WINCH TRAY, SPORTSMAN
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT Y1 Y2 3300 3800 3300 3800 2 12 set by hand or by optional RCU (Remote Control Unit) X X 65 65 4-Port Antenna 3300 3800/3300 3800
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More information8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 790 960 X 1710 2180 1710 2180 0 10 0 10 0 6 0 6 set by hand or by optional RCU (Remote Control Unit) X 65 65 R2 B1 B2 X X 60 60 8-Port
More informationinstallation guide 1 GUIDE#: pwb-wwtowv1-pol-003
g300 WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 B1 1710 2180 0 14 0 8 set by hand or by optional RCU (Remote Control Unit) X 65 X 65 4-Port Antenna 790 960/1710 2180 65 /65 14.5/17.5dBi
More information1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM
August12, 2003 ASSEMBLY MANUAL Revision E 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM E Revised
More informationINSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS
INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. A1-Tools... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...
More informationHydrajaws Safety Lifeline Tester
Hydrajaws Safety Lifeline Tester Operating Instructions HYDR AJAWS LIMITED Hydrajaws Safety Lifeline Tester 4 5 1 6 7 2 3 9 10 8 12 11 TECHNICAL SPECIFICATIONS Load Gauges Range available: Analogue: 0-25kN/lb/f
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationRepair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group
MK Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A General Pump is a Member of The Interpump Group 8 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page
More informationType XTSR71 Sizes
(Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts
More informationSECTION 9.0 MAINTENANCE
SECTION 9.0 MAINTENANCE SECTION 9.1 GENERAL MAINTENANCE CLEANLINESS IS THE KEY TO THE PERFECT STO-AWAY KEEP DIRT, MUD, AND SALT FROM BUILDING UP ON YOUR STO-AWAY If you have a pressure washer, use it to
More informationADDUCO Hydraulic Clamping Nut
Translation of Original Operating Manual ADDUCO Hydraulic Clamping Nut Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property
More informationInstallation and Operational Instructions for ROBA -DS couplings Type 95. _ (disk pack HF) Sizes
95. _ (disk pack HF) Sizes 6 22 Please read these Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to coupling failure, resulting
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationModel POA-CHB-XL50. Assembly and Installation Manual. Projector Bracket. Contents. Be sure to consult with a qualified installation specialist
Assembly and Installation Manual Projector Bracket Model POA-CHB-XL50 Be sure to consult with a qualified installation specialist This bracket is specifically for use with our projector. Be especially
More informationMast and Antennas for Field Day & Emergencies
Mast and Antennas for Field Day & Emergencies John A. Allocca, WB2LUA, July 2005 This is a 27 feet 1.5 diameter portable guyed mast with a 28 feet diameter footprint. It breaks down into four 6 feet sections
More informationDUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS
DUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS Copyright 2010. Star Trac by Core Industries, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without
More informationINSTALLATION GUIDE Rear Bumper. Jeep JL Wrangler
INSTALLATION GUIDE Rear Bumper Jeep JL Wrangler Dual Swing System 1A From the stock bumper you removed from vehicle, you ll need to take the parking sensor wiring from it and feed it into the new bumper.
More informationELECTRIC TOOL CORPORATION
Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More information1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM
August 21, 1997 Revision D ASSEMBLY MANUAL 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM PRODELIN CORPORATION 1700 NE CABLE DRIVE CONOVER, NC 28613-0368 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM D
More informationM2 Antenna Systems, Inc. Model No:
M2 Antenna Systems, Inc. Model No: 400-600-10 SPECIFICATIONS: Model... 400-600-10 Frequency Range... 390 To 650 MHz *Gain... 12 To 13 dbic Front to back... 20 db Nominal Beamwidth... 46 Nominal Feed Impedance....
More informationM2 Antenna Systems, Inc. Model No: 20M5LD
M2 Antenna Systems, Inc. Model No: 20M5LD SPECIFICATIONS: Model... 20M5LD Frequency Range... 14.0 14.350 MHz *Gain (Full Band)... 10.2 dbi Typical Front to back... 23 db Typical Beamwidth... E=50 / H=66
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R1 698 960 1710 2690 1710 2690 1.5 10 0 10 2 10 set by hand or by optional RCU (Remote Control Unit) X Y1 X Y2 65 65 65 X 6-Port
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R1 0.5 7 0 6 set by hand or by optional RCU (Remote Control Unit) X 90 B1 X 90 4-Port Antenna / 90 /90 16.5/18i 0.5 7 /0 6 T Type
More informationMODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS
MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure
More informationQuick Set Dovetail Jig
Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT
More informationSelf-assembly and pole conversion system
User Manual Self-assembly and pole conversion system Swivelpole R11, R12 and R13 for self-assembly of lowering poles on greenfield projects or conversion of non-lowering poles on brownfield facilities.
More informationInstalling the Hughes BGAN Remote Antenna
Installing the Hughes BGAN Remote Antenna Product description BGAN Remote Antenna The Hughes BGAN Remote Antenna (HNS Part No. 9501286-0001) is designed to be permanently installed with the Basic Fixed
More informationinstallation guide 1 GUIDE#: pwb-assault-004
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More information1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More informationConverting the MGL SERVO to a MGL CAPSTAN SERVO.
Parts supplied in kit Converting the MGL SERVO to a MGL CAPSTAN SERVO. 1 x bracket, 1 x bracket clamp, 4 x cap head screws M4 x 8 1 x nut M6, 1 x washer M6, 1 x drum, 1 x shear screw M3, 2 x grub screws
More informationInstruction Manual. LSV36108A 3600# Vertical Lift LAKESHORE PRODUCTS, INC.
LAKESHORE PRODUCTS, INC. Quincy. MI. 49082. tel 517.639.3815 LSV36108A 3600# Vertical Lift Instruction Manual Read carefully. Failure to follow the instructions and safety rules could result in severe
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R1 790 960 1710 2180 1710 2180 2 14 0 14 0 14 set by hand or by optional RCU (Remote Control Unit) X B1 X B2 65 65 65 X 6-Port Antenna
More informationinstallation guide 1 GUIDE#: pwb-assault-001
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationINSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011
INSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011 Specifications: Installs to K-Series desk or wall mount. Accommodates K-Series mounting arms (fixed
More informationINSTALLATION INSTRUCTIONS UTV LIGHT BAR KIT Part Number: and Application: All UTV s*
INSTALLATION INSTRUCTIONS UTV LIGHT BAR KIT Part Number: 83970 and 84360 Application: All UTV s* * does not include Arctic Cat vehicles Your safety, and the safety of others, is very important. To help
More informationM2 Antenna Systems, Inc. Model No: 20M6-125
M2 Antenna Systems, Inc. Model No: 20M6-125 SPECIFICATIONS: Model... 20M6-125 Frequency Range... 14.0 14.350 MHz *Gain, (FS) / Over gnd... 11.19dBi / 16.6dBi @70 Front to back... 25 db Typical Beamwidth...
More informationQuick-Lock LEM >700 User Manual
Quick-Lock LEM >700 User Manual 1st release, version 03/2015 [English] Sold by: Kanaltechnik GmbH Published by: Uhrig Kanaltechnik GmbH Am Roten Kreuz 2 78187 Geisingen, Germany Tel. +49 (0) 7704 / 806-0
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationTUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL
TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL 1 CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine s Description and Purpose of Use 3 2.1. Machine s description
More information1 of 12 5/24/2015 9:43 AM
1 of 12 5/24/2015 9:43 AM REAR PROPELLER SHAFT ASSEMBLY Components REMOVAL 1. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 2 of 12 5/24/2015 9:43 AM a. Place match marks on the propeller shaft flange
More informationForm No Assembly & Operating Instructions for: SAFETY PRECAUTIONS
Form No. 0230 Assembly & Operating Instructions for: 833 20300 83 2220 837 0-0008 078 SHOP PRESS Max. Capacity: 2 Ton These instructions are intended for various shop presses. Some models are shipped assembled
More informationEraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the conveyor has been disconnected and con
INSTALLATION GUIDE LIB-CP-REA-03-01 Rev. 10 Eraser Conveyor Belt Cleaning System ARGONICS Eraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 0 10 2 8 set by hand or by optional RCU (Remote Control Unit) X 65 Y1 1710 2690 X 65 4-Port Antenna 790 960/1710 2690
More informationTechnical publication. Path alignment and cross polarization procedure for parabolic microwave antennas
Technical publication Path alignment and cross polarization procedure for parabolic microwave antennas Contents 1.0 Introduction 3 2.0 Path alignment procedure 3 2.1 Setting azimuth marker 3 2.2 Test equipment
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More information1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers
INSTRUCTION MANUAL 1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers Read and understand all of the instructions and safety information in this manual before operating or servicing
More informationSERIES M Ku-BAND Rx / Tx ANTENNA SYSTEM
4096-432 June 15, 2011 REVISION D ASSEMBLY MANUAL SERIES 1125 1.2M Ku-BAND Rx / Tx ANTENNA SYSTEM General Dynamics 1500 PRODELIN DRIVE NEWTON, NC 28658 PRODELIN CORPORATION 4096-432 SERIES 1125 1.2M Ku-BAND
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3358-2 PCN 060712-5 Side-of-Pole Mount for 4 Modules (SPM4) For
More informationINSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS
INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. LA-Tool... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...
More informationOur service team is at your disposal for further information. Franke GmbH Obere Bahnstr Aalen Germany Tel.: /920-0 Fax.
Our service team is at your disposal for further information. Franke GmbH Obere Bahnstr. 64 73431 Aalen Germany Tel.: 07361 /9200 Fax.: 07361/920120 www.frankegmbh.com www.frankebearings.de www.frankelinearguides.de
More information6 Cub Pack Drawer IMPORTANT WARNING! INSTALL TIME: 45 mins SSAM014
6 Cub Pack Drawer SSAM014 INSTALL TIME: 45 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
More informationM2 Antenna Systems, Inc. Model No: 2M5WL
M2 Antenna Systems, Inc. Model No: 2M5WL SPECIFICATIONS: Model... 2M5WL Frequency Range... 144 To 148 MHz *Gain... 16.84 dbi Front to back... 22 db Typical Beamwidth... E=26 H=29 Feed type... T Match Feed
More informationReliance SG800 Series Steel Water Gage Valves
Installation, Operation, & Maintenance Instructions R500.541D1 10/16/2016 Reliance SG800 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationInventory (Figure 2)
MODEL T10127 12" SPIRAL CUTTERHEAD INSTRUCTIONS The Model T10127 indexable insert spiral cutterhead is designed to replace the straightknife cutterhead from the Grizzly jointer Model G0609. The total procedure
More informationCisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)
Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) Overview This document describes the 13.5-dBi Yagi mast mount antenna and provides instructions for mounting it. The antenna operates in the
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationInstallation, Assembly, and Operation Manual: Multi-Section Prestige Flagpole
Installation, Assembly, and Operation Manual: Multi-Section Prestige Flagpole We are honored that you have selected a Trident Support Prestige Flagpole from which to proudly fly the flag of your choice.
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More informationC a r r i a g e A s s e m b l y R e p l a c e m e n t
E1 TF-CR C a r r i a g e A s s e m b l y R e p l a c e m e n t October 2007 Software Version 5.0 and higher IMPORTANT! TigerStop must be enabled with a code that must be obtained from TigerStop Customer
More information(Fig 1) Column to Base 1. Place Column (7) on the Base (13) and align holes in the Column with holes in the Base. 2. Attach using Bolt Washer and Spring Washer hole through the Column and into the Base.
More informationOPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES
OPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES 1 Contents 1. Introduction 2. Safety instructions and precautions 3 Operating the clamp 3.1 Clamp set up 3.2 Sequence for clamp set up 3.3 Adjusting
More informationINS-AS Dual Bracket Mounting Kits for Quintel Antennas
The Quintel Optimal Separation (QOS) Dual Mount Antenna Bracket Kit allows a variable horizontal separation for a single band or across multiple bands for two Quintel QS Series antennas when operating
More informationINSTRUCTION MANUAL. Lathe Duplicator MODEL North Glenn Road, Casper, Wyoming woodworker.com
140-069LatheDuplictr(1/12) 10/30/06 8:20 AM Page 1 INSTRUCTION MANUAL Lathe Duplicator MODEL 140-069 1108 North Glenn Road, Casper, Wyoming 82601 1-800-645-9292 woodworker.com 140-069LatheDuplictr(1/12)
More informationSquare Wheel Belt Grinder Models: 4103, 4106, and 4126AC
This Manual is Bookmarked Operating Instructions Parts Manual Square Wheel Belt Grinder Models: 4103, 4106, and 4126AC WHM TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www.wmhtoolgroup.com
More information