Quick-Lock LEM >700 User Manual

Size: px
Start display at page:

Download "Quick-Lock LEM >700 User Manual"

Transcription

1 Quick-Lock LEM >700 User Manual 1st release, version 03/2015 [English] Sold by: Kanaltechnik GmbH

2 Published by: Uhrig Kanaltechnik GmbH Am Roten Kreuz Geisingen, Germany Tel. +49 (0) 7704 / Fax +49 (0) 7704 / Internet info@uhrig-bau.de 2

3 Contents 1. About this document Regulations Certifications Description of the Quick Lock LEM > Intended use Suitability and materials used Components and functions Description of the system and procedure Suitability and materials used How to use the system Preparation Inspecting the pipe Preparing the pipe Equipment and materials Preparation: Trimming the liner Installing the Quick-Lock LEM> Tool maintenance Appendix Pneumatic cutter for liner end sleeves Maintenance instructions for the pneumatic cutter Data sheet

4 1. About this document These instructions supplement the basic Quick-Lock user manual. They specifically describe how to use the Quick-Lock liner end sleeve > 700. Please observe the aforementioned user manual with its general instructions on using the Quick-Lock system. 1.1 Regulations The basis and general specification for pipe repairs using the Quick-Lock system is DWA data sheet M143 Part 3 Repairing wastewater pipes and sewers with internal sleeves See the main user manual. 1.2 Certifications An application for technical approval will be submitted shortly. 4

5 2. Description of the Quick Lock LEM > Intended use Cross-section The Quick-Lock liner end sleeve > 700 is a product for permanently and tightly sealing liner systems to the host pipes or manhole pipe connections in the range of diameters from DN 700-DN Suitability and materials used The system is made from V4A stainless steel of grade (AISI 316L) a nd an EPDM compression seal. The materials used are permanently resistant in municipal wastewater systems. The suitability of the materials must be ascertained for use in industrial or polluted wastewater. The Quick-Lock liner end sleeve may only be installed in cured, stress-free liner systems. Hydrophilic waterstop tape does not need to be used around the liner. The basis for selecting a suitable liner end sleeve is the technical data sheet (appendix 1). Observe the instructions in section 1.6 of the main user manual. 5

6 2.3 Components and functions System components Two-piece stainless steel sleeve Locking screws (4x) Sliding blocks (4x) Rubber jacket (1x) Compensating rubber (1 or 2, if needed) 2.4 Description of the system and procedure See the main usermanual. 2.5 Suitability and materials used See the main usermanual. 6

7 3. How to use the system 3.1 Preparation Inspecting the pipe Before using the Quick-Lock liner end sleeve, check the area where the liner is connected to the host pipe or the manhole pipe connection to see whether the liner end sleeve is suitable Preparing the pipe Repairing the contact surfaces A reliable compression seal is only possible if the quality of the surface is suitable for sealing. Repair any irregularities or holes in the host pipe or the manhole pipe connection. Only used mineral or epoxy-based materials. Let the material cure. 7

8 3.2 Equipment and materials Installation tools (Supplied by Uhrig) Four-piece clamping tool set 2x with screw unit 2x with seat (1) Spindle For pre-tensioning the sleeve (2) Clamping screws For clamping the sleeve and pressing it in place (3) Retaining lug For attaching the tool to the sleeve Pneumatic cutter A pneumatic cutter is required for cutting back the liner. Uhrig supplies pneumatic cutters that are specially designed for cutting liners. They are lowmaintenance and have an adjustable cut depth. Observe the operation and maintenance instructions in the appendix. 8

9 Required accessories Make sure you have the necessary tools. If necessary we can provide the tools for sale or hire. Lubricant Ruler or tape measure 8 mm Allen key 17 mm socket Crayon Interchangeable socket wrench (or 17 mm ratchet wrench) Open-end spanner with 17 mm ring ratchet Plastic or rubber mallet Talcum powder Laser for measuring the damaged area (optional, not shown) Gauge Pneumatic socket wrench (optional for rapid installation) 9

10 3.3 Preparation: Trimming the liner Fitting the depthstop Measure the thickness of the liner. Fit the appropriate depth stop onthe pneumatic cutter. Trimming the liner Using the pneumatic cutter, make a radial cut around the entire sleeve circumference. Liner trimlength: DN 700 DN 1200: 265 mm Measure from the position where the front edge of the sleeve will be. Make a longitudinal cut with a pneumatic angle grinder. Do not damage the host pipe. Remove the liner offcut. Deburr the new end of the liner with the angle grinder. Clean the area where the liner will be connected with a high-pressure jet. Longitudinal cut Make a longitudinal cut with a pneumatic angle grinder. Do not damage the host pipe. Remove the liner offcut. Deburr the new end of the liner with the angle grinder. Clean the area where the liner will be connected with a high-pressure jet 10

11 3.4 Installing the Quick-Lock LEM >700 Installation Bringing in thesleeve Do not assemble the sleeve. Bring in the sleeve via the manhole entrance. Remove the edge protection on the metal rim. Putting the sleeve together Join the sleeve sections together so that their respective engraved tracks are on the outside. Place the sliding blocks in the tracks. Secure the sliding blocks with the locking screws. Adjust the sleeve to the smallest diameter and tighten the locking screws. Applying talcum powder to the rubber jacket Apply talcum powder to the inside of the rubber jacket. 11

12 Fitting the rubberjacket Pull the jacket over the sleeve and center it on the 300 mm wide (without rims) steel sleeve. The preassembled sleeve is rolled so tightly that it can be taken into the pipe and turned around there. Fitting compensating rubbers (if necessary) For greater liner thicknesses, one or two compensating rubbers must be mounted (see data sheet). Peel back the rubber jacket. Pull on one or two compensating rubbers over the sleeve (on the side with the larger border). Fold the rubber jacket back over the compensating rubbers. Check for correct seating. Aligning the rubber jacket Check and correct the fit of the rubber jacket: Position the compensating rubbers so thatthe edges lie under each other (see figure). 12

13 Positioning the liner end sleeve in the host pipe Depending on the type ofconnection: Alternative A (standard method): Connecting to liner in host pipe Rubber jacket is seated in the center around the steel sleeve. Alternative B: Connecting to liner in manhole pipe connection Rubber jacket is seated in the center around the steel sleeve. This requires that the surface of the manhole pipe connection be suitable for sealing and that there are no significant bends in the connection from the host pipe to the manhole. Maximum bend 1.0. For a tight seal, the sealed area of the manhole wall (pipe connection) must be at least 110 mm. Alternative C: Edge of the sleeve as repair bead Rubber jacket is seated in the center around the steel sleeve. The flared end of the sleeve protrudes mm inside the manhole and acts as a bead for repairs around the pipe connection. 13

14 Positioning and aligning thesleeve Align the sleeve inside the pipe. Turn the sleeve so that the locking screws are roughly level on the left and right sides of the pipe. The sleeve must always be installed perpendicular to the axis of the pipe. When using a spirit level, the pipe slope must be adjustable. Attaching and securing the clampingtools The clamping tools on the left and right sides are identical. However, the clamping tools are aligned differently on the left and right: oneclamping screw points up and the other points down. Attach the two parts of each clamping tool as close together as possible. Tighten the spindles to hold the clamping tools in place. Expanding the sleeve Start on one side. Loosen the locking screws. Tighten the spindle to about half way until the sleeve is pressed against the pipe. When expanding the sleeve, make sure it opens up evenly. The easiest way to do this is to look at the holes on the left and right. Continue on the other side: Loosen the locking screws here too. Tighten the spindle to about half way. 14

15 Checking the alignment in the pipe Before the sleeve is on the pipe, check the alignment once more and correct it, if necessary. Repositioning the clamping tools Tighten the locking screws. Loosen the spindles. Reposition the two parts of each clamping tool as close together as possible. Fasten them with the clamping screws. Clamping Keep working on both sides of the sleeve alternately: Tapping in Note Loosen the locking screw. Tighten the two clamping screws evenly. Use the holes as a guide. While you are doing this, occasionally tap all the way round the sleeve with the mallet so that the tension is evenly distributed. The spindle is only designed for expanding the sleeve. The sleeve is clamped using the two clamping screws on the left and right of the tool. 15

16 Reaching the maximum compressionof the seal nubs Keep clamping until the added material (non-compressible rubber jacket + metal thickness) is less than: Measured in liner: 8-9 mm Measured in host pipe: mm with no compensating rubber mm with 1 compensating rubber mm with 2 compensating rubbers You can use the gauge from the accessories as an aid. Set this to the value with or without compensating rubbers and lay it over the sleeve. If the measuring instrument lies against it, the maximum compression has been reached. Eccentric expansion of the sleeve To compens ate for differing liner thic knesses, the sleeve can be expanded eccentrically up to 8 mm by tightening the inner and outer clamping screws by different amounts. Note: If the sleeve is expanded too eccentric ally, the tools can become jammed. Use the holes as a guide. 16

17 Tightening the locking screws Make sure that the sleeve has reached its final state. Tighten the locking screws using the ratchet. Removing the clampingtools Loosen the clamping screws of the tools. Remove the tools. The Quick-Lock LEM >700 now forms a tight and reliable seal. 17

18 3.5 Tool maintenance Maintenance The spindles and clamping screws must be treated with high-pressure lubricant (Metaflux lubricating metal) after each use. Conversion of the clampingtools The clamping tool set can be used for both the Quick-Lock BIG an Quick-Lock LEM >700. For this reason, there are side pieces in two widths. Side piece for Quic k-lock BIG (approx. 20 cm wide) Side piece for Quic k-lock LEM >700 (approx. 30 cm wide) Mount the plates on the corresponding side pieces. Screw the clamping screws into the corresponding side piece. 18

19 4. Appendix 4.1 Pneumatic cutter for liner end sleeves Observe the operating instructions: Safety: Always wear face, ear and mouth protection. Only use the tool for its intended purpose. The tool may only be used by qualified personnel. Pneumatic system requirements: Minimum compressor output 1.1 m³/min. Recommended operating pressure 6.2 bar at the tool (maximum operating pressure at the tool 8 bar) Air hose 13 mm ID, maximum length 20 m. Only use the pneumatic cutter with the oil and oiler supplied, oil quantity: approx. 1 drop/min. Air consumption approx l/min. Always observe the operating manual supplied with the equipment. 19

20 4.2 Maintenance instructions for the pneumatic cutter Clamp the holder for the pneumatic cutter in a vice. Clamp the tool in theholder. Using the wrench provided, unscrew the pneumatic cutterin a clockwise direction Remove the pneumatic motor and the spacer bushing. Take the blades out of the pneumatic motor. Blow out the housing and motor with compressedair. Spray the pneumatic motor with WD 40 anti-corrosion spray or a similar product. Put the blades back in, with the tapered side on the inside. Reassemble the pneumatic cutter and tighten it hand-tight with the wrench. 20

21 - V4A : da/da - Min/max pipe ID Technical data sheet Liner trim length: RS Liner Liner thickness: S Liner Rubber thickness: S Rubber Sleeve length L Metal thickness V4A: S V4A Liner end sleeve DN Hn1 : Seal height: Hn2 Liner end sleeve Sleeve length Suitable for pipes from / to Pipe ID min. Pipe ID max. Liner thickness 1 max Liner trim length Metal thickness Stainless steel sleeve V4A pipe rolled Max. expanded diameter Rubber thickness Rubber jacket Height of seals mm mm mm mm mm mm mm mm mm mm mm mm x- parts DN: L DN min DN max S Liner RS Liner S V4A da DA S Rubber Hn1 Hn Version: 01/

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

Pneumatic Drill / / Technical Specification

Pneumatic Drill / / Technical Specification CS UNITEC Pneumatic Drill 2 2502 0010 / 2 2502 0030 2 2506 0010 / 2 2506 0030 Technical Specification Model with Lever Throttle Model with Twist Throttle with Selfresetting 2 2502 0010 2 2502 0030 2 2506

More information

Assembly instructions

Assembly instructions Assembly instructions Important notes on VOSS assembly instructions In order to ensure maximum performance and functional reliability of VOSS products, the respective assembly instructions, operating conditions

More information

Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2

Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 TOOLS Page Q 2 Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 Page Q 3 Changeable carbide drill (WHM) Page Q 3/1 Drilling machine Tonisco

More information

Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX

Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX NMT 553-01(e) These Installation Instructions are valid for antennas in the following version : Reflector Ø

More information

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all

More information

What is a fastener? A device to locate or hold parts

What is a fastener? A device to locate or hold parts What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how

More information

Zero Point Clamping System. ZERO lock BALL lock

Zero Point Clamping System. ZERO lock BALL lock Zero Point Clamping System ZERO lock BALL lock kap3 kap 263 Technical information regarding ZERO lock Zero Point Clamping System Application The modularly designed, flexible ZERO lock Zero-Point Clamping

More information

CONNEX-Junction. for subsequent lateral connections to thin-walled drainage and sewer pipes. adjustable durable leakproof

CONNEX-Junction. for subsequent lateral connections to thin-walled drainage and sewer pipes. adjustable durable leakproof CONNEX-Junction for subsequent lateral connections to thin-walled drainage and sewer pipes adjustable durable leakproof The product Thanks to the CONNEX-Junction, house connection lines or lateral pipes

More information

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard 5. Input Cover 6. O-Ring 7. Hex Head Cap Screw 8. Input

More information

Drake Off Road Hood Hold Downs Installation Guide

Drake Off Road Hood Hold Downs Installation Guide Installation Time: 30 Minutes Tools Required: Drake Off Road Hood Hold Downs Installation Guide 3/8 drive ratchet 13mm socket 10mm socket (deep-well socket helpful) 13mm wrench (2x) 4mm allen wrench 5mm

More information

...thoroughly tried and tested!

...thoroughly tried and tested! ...thoroughly tried and tested! Tapping and bushing with EWE tools www.ewe-armaturen.de Installation and operating instructions for EWE drilling units 1. Details of product 1.1. Application field EWE tapping

More information

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL Parts & Machinery for the Abrasive Blast Industry 27301 East 121st Street Coweta, Oklahoma 74429 (918) 486-8411 Fax (918) 486-8412

More information

OPERATIONAL AND MAINTENANCE MANUAL. Drilling machine ProDrill 20 INSTRUCTION MANUAL FOR USE AND MAINTENANCE

OPERATIONAL AND MAINTENANCE MANUAL. Drilling machine ProDrill 20 INSTRUCTION MANUAL FOR USE AND MAINTENANCE MOD 14-02 OPERATIONAL AND MAINTENANCE MANUAL Rev. 0 Data 01/02/2012 Drilling machine ProDrill 20 INSTRUCTION MANUAL FOR USE AND MAINTENANCE TABLE OF CONTENTS TECHNICAL SPECIFICATIONS 2 USE 4 MAINTENANCE

More information

JARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF

JARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF Model 423-17 Brisket Scissor EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 423--17... 4037003 Air Filter / Regulator / Lubricator 3022003 Air Hose Assembly... 3059018 Balancer...

More information

These Installation Instructions are valid for antennas in the following version:

These Installation Instructions are valid for antennas in the following version: Installation Instructions 4 ft CompactLine Antennas (with E-Mount 200 km/h) SB, SBX NMT 480-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall be

More information

1. TOOLS + MATERIALS REQUIRED

1. TOOLS + MATERIALS REQUIRED R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED

More information

Page 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications

Page 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with

More information

UNDERPINNERS CS 88 & CS 89 FOOT-OPERATED PNEUMATIC. Technical and User Manual. Version 1 au 12 / 01. Cassese / Communication

UNDERPINNERS CS 88 & CS 89 FOOT-OPERATED PNEUMATIC. Technical and User Manual. Version 1 au 12 / 01. Cassese / Communication UNDERPINNERS CS 88 & CS 89 FOOT-OPERATED PNEUMATIC Technical and User Manual Version 1 au 12 / 01 Cassese / Communication CS88 / CS 89 - Technical and User Manual CONTENTS PAGE N INTRODUCTION ACCESSORIES

More information

Fifth-wheel coupling JSK 38/50

Fifth-wheel coupling JSK 38/50 Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/25 1 LT SK38C-3 English RevA Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety

More information

Simplex Baseboard System Baseboard System

Simplex Baseboard System Baseboard System Simplex Baseboard System Baseboard System I Complete installation programme I Trouble-free and time-saving installation I Various connection kits for all types of pipe Our service to you I Simplex Products

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for FortressCable H-Series Cable Panel System With UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain

More information

Installation Instructions: JK Inner Fender Liners Part Number(s): & Ratchet 3/8 & 7/16 Sockets. Plastic Clip Removal Tool

Installation Instructions: JK Inner Fender Liners Part Number(s): & Ratchet 3/8 & 7/16 Sockets. Plastic Clip Removal Tool Page 1 of 5 Proudly Made In USA Installation Instructions: JK Inner Fender Liners Part Number(s): 400.300.170 & 400.300.180 Vehicle Fitment: 2007 - Present Jeep Wrangler & Unlimited Parts List Qty: 1 Driver

More information

INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS

INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. A1-Tools... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...

More information

T : F : Revised June 2013

T : F : Revised June 2013 Revised June 2013 W R A, O USA T: 800 321 7950 440 998 2788 F: 440 992 2925... 2 INSTRUCTIONS FOR 3/4, 1, 1-1/4 DIAMETER TAPS FIGURE 1 A B C D E F G HOT TAP SPINDLE HOT TAP SLEEVE HOT TAP FEED SCREW ADAPTER

More information

ELECTRIC TOOL CORPORATION

ELECTRIC TOOL CORPORATION Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs

More information

Maintenance Information

Maintenance Information 16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

PURESTREAM SYSTEM - ASSEMBLY GUIDE

PURESTREAM SYSTEM - ASSEMBLY GUIDE PURESTREAM SYSTEM - ASSEMBLY GUIDE VISIT OUR WEBSITE : www.cagpurification.com our installment procedure videos in the PURESTREAM Piping section. NECESSARY TOOLS FOR INSTALLATION We suggest the use of

More information

Repair manual. Fifth-wheel coupling JSK 38/50

Repair manual. Fifth-wheel coupling JSK 38/50 Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/212 1 Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety requirements and must

More information

Staple Specification:

Staple Specification: H-1027, H-1028 H-3064 PNEUMATIC STICK STAPLER stapler specifications Dimensions: L x H x W 13.5 x 8.75 x 6" Weight (Without Fasteners) Compressed Air: Maximum psi: Recommended Operating Pressure: Air Consumption:

More information

C70 Window Roller Repair Taken from: Heres the problem:

C70 Window Roller Repair Taken from:  Heres the problem: C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70

More information

Water Line and Water Line Assembly Gasket

Water Line and Water Line Assembly Gasket 1 Preparation for Repair 1) Remove tip from scaler 2) Remove scaler from air supply 3) Remove gasket from back end of scaler. Examine gasket for obvious wear or disfigurement. Replace if necessary. 2 Remove

More information

Hydrajaws Safety Lifeline Tester

Hydrajaws Safety Lifeline Tester Hydrajaws Safety Lifeline Tester Operating Instructions HYDR AJAWS LIMITED Hydrajaws Safety Lifeline Tester 4 5 1 6 7 2 3 9 10 8 12 11 TECHNICAL SPECIFICATIONS Load Gauges Range available: Analogue: 0-25kN/lb/f

More information

WSG 8-115; 8-125; P; WSG ; WSG P; WSG PS; WSG P; WSG 15-70Inox

WSG 8-115; 8-125; P; WSG ; WSG P; WSG PS; WSG P; WSG 15-70Inox Repair instructions Page of 47 Contents. Models described 2. Technical data 3. Notes and requirements 4. Tools required 5. Lubricants and auxiliary substances required 6. Disassembly 7. Assembly 8. Connection

More information

MODELS 49 RA 49 RAZ 49 RAC

MODELS 49 RA 49 RAZ 49 RAC General Safety and Maintenance Manual MODEL grinder featuring a rear exhaust. Model Number Exhaust Direction REAR Throttle Type (L) Lever or (K) Safety Lever Speed 12000 to 14000 R.P.M (13500rpm is standard)

More information

Psi casing ENd seals type Kt type du type KG/Ko type HA type stm

Psi casing ENd seals type Kt type du type KG/Ko type HA type stm PSI Casing end seals type kt type du type kg/ko type ha type stm www.psi-products.com 101 PSI Casing End Seals Pipes carrying media (e.g. gas pipes, water pipes, sewage pipes, etc.) below motorways, main

More information

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4.1 EXPLODED VIEW DRAWING REF. QTY. DB DC DF DG DJ DL DESCRIPTION PART # 1 1 ADAPTOR FRAME 034007 2 12 LOCK WASHER 3/8 x 1/8 S.S. 034004 3 12 HEX HEAD

More information

Tuf-Lite III Fans 5000K Series Hub

Tuf-Lite III Fans 5000K Series Hub Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information

HBS-AP ASSEMBLING INSTRUCTIONS

HBS-AP ASSEMBLING INSTRUCTIONS ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK 97 HBS-AP ASSEMBLING INSTRUCTIONS 1. INTRODUCTION 1.1. This manual is very easy to consult and we recommend reading it before starting work,

More information

OPERATION MANUAL. High Efficient Multiple Blade Saw WINTER MBS 600, MBS 930 WARNING!

OPERATION MANUAL. High Efficient Multiple Blade Saw WINTER MBS 600, MBS 930 WARNING! OPERATION MANUAL High Efficient Multiple Blade Saw WINTER MBS 600, MBS 930 WARNING! The operator must thoroughly read this manual before operation. Keep this manual for future reference. Henrik Winter

More information

DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks

DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks Mounting Instructions For DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks WARNING: Because of the possible danger to person(s) or property from accidents which may result from the

More information

Pole Conversion System For safe and efficient conversion of non-lowering light poles.

Pole Conversion System For safe and efficient conversion of non-lowering light poles. Conversion System USER GUIDE: OVERVIEW The Swivelpole Conversion Tool clamps onto the existing non-lowering pole and safely supports the pole during a cold cut with the Ratchet Pipe Cutter, eliminating

More information

HANDHOLE SEAT GRINDER

HANDHOLE SEAT GRINDER 1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,

More information

Side and rear window, assembly overview

Side and rear window, assembly overview 64-7 Side and rear window, assembly overview 1 - Side/rear window Removing Unbroken Page 64-9 Broken Page 64-11 Installing Page 64-13 Curing time Page 64-21 Re-sealing Page 64-25 2 - PUR adhesive sealant

More information

Tuf-Lite III Fans 3000K Series Hub

Tuf-Lite III Fans 3000K Series Hub Tuf-Lite III Fans 3000K Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 11 thru 15 Diameter Hudson Tuf-Lite III fan blades Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information

Cut-True 16M Manual Paper Cutter

Cut-True 16M Manual Paper Cutter Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation

More information

LPK1550 Hydraulic Crimping Tool 15-ton

LPK1550 Hydraulic Crimping Tool 15-ton SERVICE MANUAL LPK1550 Hydraulic Crimping Tool 15-ton Serial Code FYF Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register

More information

SETTING UP THE MODEL 210B-2 SRA

SETTING UP THE MODEL 210B-2 SRA SETTING UP THE MODEL 210B-2 SRA SAFETY PRECAUTIONS FOR THE MODEL 210B-2 SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris:

More information

Operator's manual. TruTool TKF 1500 (1A1), (1B1)

Operator's manual. TruTool TKF 1500 (1A1), (1B1) Operator's manual TruTool TKF 1500 (1A1), (1B1) Table of contents 1 Safety 4 1.1 General safety information 4 1.2 Specific safety information for beveler 4 2 Description 6 2.1 Intended use 6 2.2 Technical

More information

Tuf-Lite II Fans 3000H Series Hub

Tuf-Lite II Fans 3000H Series Hub Tuf-Lite II Fans 3000H Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Fan Blades Hudson Tuf-Lite II (white, prev. Blue**) are made from fiberglass

More information

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation

More information

Tuf-Lite II Fans 3000H Series Hub

Tuf-Lite II Fans 3000H Series Hub Tuf-Lite II Fans 3000H Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Fan Blades Hudson Tuf-Lite II (white, prev. blue**) fan blades are made from

More information

Band Clamping Systems. Universal Hose and Pipe Clamps Made in Germany

Band Clamping Systems. Universal Hose and Pipe Clamps Made in Germany Band Clamping Systems Universal Hose and Pipe Clamps Made in Germany Bandimex Befestigungssysteme GmbH Bandimex Befestigungssysteme GmbH was founded in 1982 and has developed into an internationally active

More information

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE The material included in this kit is to be used for WC styles of brakes that are designed or upgraded to the EP

More information

SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET

SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET Contents Section I: Scull Grip Replacement: Fixed Handle or 10 cm Length Adjustment System Refer to this section if you need to replace the grips on your fixed

More information

Tuf-Lite II Fans 3000HC Series Hub

Tuf-Lite II Fans 3000HC Series Hub Tuf-Lite II Fans 3000HC Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 8 through 10 Diameter Hudson Tuf-Lite II (White) are made from fiberglass reinforced vinyl-ester

More information

INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS

INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. LA-Tool... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...

More information

Tuf-Lite III Fans 5000K Series Hub

Tuf-Lite III Fans 5000K Series Hub Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information

Operating Manual Axis 60mm Self Centering Vise Axis 100mm Self Centering Vise

Operating Manual Axis 60mm Self Centering Vise Axis 100mm Self Centering Vise Operating Manual Including installation and assembly instructions 80000 5-Axis 60mm Self Centering Vise 80100 5-Axis 100mm Self Centering Vise 80300 5-Axis 40mm Fixed Jaw Vise 80400 5-Axis 60mm Fixed Jaw

More information

400 SERIES GRINDER PUMPS 41502, 42202,43302, AND MODELS

400 SERIES GRINDER PUMPS 41502, 42202,43302, AND MODELS Section: MOYNO 500 PUMPS Page: 1 of 6 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 400 SERIES GRINDER PUMPS 41502, 42202,43302, AND 44402 MODELS DESIGN FEATURES Housing: Cast iron Pump Rotor: Chrome

More information

Assembly & Installation Guide. High Performance. Utility Poles

Assembly & Installation Guide. High Performance. Utility Poles Assembly & Installation Guide High Performance Utility Poles RS Technologies Inc. www.rspoles.com Email Info@RSpoles.com Toll Free +1 877 219 8002 Phone +1 519 682 5202 Fax +1 519 682 3786 RS Technologies

More information

Rev B C-RING TOOL VA0375 ½ in. OPERATING MANUAL

Rev B C-RING TOOL VA0375 ½ in. OPERATING MANUAL Rev B 4-30-0 C-RING TOOL VA0375 ½ in. OPERATING MANUAL Operational Instructions for Vertex C-Ring Tool VA0375 Vertex Fasteners is committed to providing our customers with world-class customer service

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our

More information

GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.

More information

PRODUCT: BALDUR + ODEN

PRODUCT: BALDUR + ODEN R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED

More information

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24 CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 0//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No (Replaces (HTR1031E) And (HTR1031E1))

HAND CRIMP TOOL SPECIFICATION SHEET Order No (Replaces (HTR1031E) And (HTR1031E1)) HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-3200 (Replaces 11-01-0084 (HTR1031E) And 11-01-0211 (HTR1031E1)) TYPE 2C SCOPE Terminal Wire Size Insulation Diameter Strip Length AWG mm² mm In. mm

More information

No September, Char-Lynn. Power Steering. Repair Information. 20 Series Steering Control Unit 001

No September, Char-Lynn. Power Steering. Repair Information. 20 Series Steering Control Unit 001 Char-Lynn Power Steering No. 7-313 September, 1997 Repair Information 20 Series Steering Control Unit 001 Bearing Race Retaining Ring Needle Thrust Bearing Bearing Race Seal Ring Backup Washer Seal (3

More information

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group MK Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A General Pump is a Member of The Interpump Group 8 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and

More information

How to Mount a Moto Accessories MV Agusta F4 Hugger in Less than 30 Minutes.

How to Mount a Moto Accessories MV Agusta F4 Hugger in Less than 30 Minutes. How to Mount a Moto Accessories MV Agusta F4 Hugger in Less than 30 Minutes http://idealcycle.com/mv_agusta Materials and Tools: 13 10 4 1 3 2 5 11 6 15 17 14 12 9 8 16 7 1. Electric drill 2. Tap drill

More information

NATIONAL CERTIFICATE (VOCATIONAL) NOVEMBER

NATIONAL CERTIFICATE (VOCATIONAL) NOVEMBER MARKING GUIDELINE NATIONAL CERTIFICATE (VOCATIONAL) NOVEMBER 2009 NQF LEVEL 2 This memorandum consists of 7 pages. MARKING GUIDELINE -2- NC930(E)(N25)V QUESTION 1: GENERAL. 1.1 TRUE OR FALSE 1.1.1 1.1.2

More information

LK36-LK40-LK45 LK50-LK55-LK60

LK36-LK40-LK45 LK50-LK55-LK60 LK Repair Manual LK36-LK40-LK45 LK50-LK55-LK60 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page 3 2.1

More information

Magnetic Base Drilling Machine A100/32. Operators Instruction Manual And Spare Parts Listings

Magnetic Base Drilling Machine A100/32. Operators Instruction Manual And Spare Parts Listings Magnetic Base Drilling Machine A100/32 Operators Instruction Manual And Spare Parts Listings Index Chapter 1. Technical Overview. Chapter 2. Warnings and Safety Instructions. Chapter 3. Operating Instructions.

More information

Assembly instructions

Assembly instructions Assembly instructions Important notes on VOSS assembly instructions In order to ensure maximum performance and functional reliability of VOSS products, the respective assembly instructions, operating conditions

More information

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO 47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small

More information

UNPACKING. Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES.

UNPACKING. Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES. UNPACKING Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES. Please take sufficient time and read this manual carefully before you start installation and operation

More information

Fluid Sealing Association

Fluid Sealing Association Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850

More information

The following instructions will guide you through the installation of your new vinyl railing.

The following instructions will guide you through the installation of your new vinyl railing. Installation Guide St. James Vinyl T-Rail Tools Required Protective eye glasses 3/8 x 3 Concrete Anchors/Fasteners (for Tape measure concrete installations) Variable speed drill/screwdriver Philips Driver

More information

Tuf-Lite III Fans K Hi Temp 3000KHT Series Hub

Tuf-Lite III Fans K Hi Temp 3000KHT Series Hub Tuf-Lite III Fans K Hi Temp 3000KHT Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 11 thru 15 Diameter Hudson Tuf-Lite III fan blades Hudson Tuf-Lite III Hi Temp (Red) fan blades are of single

More information

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...

More information

INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL

INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. B2 Tools... 6 2.1 Technical Data... 6 2.2 Overview: Main components... 7

More information

1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers

1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers INSTRUCTION MANUAL 1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers Read and understand all of the instructions and safety information in this manual before operating or servicing

More information

Tuf-Lite II Fans H Hi Temp 3000HT Series Hub

Tuf-Lite II Fans H Hi Temp 3000HT Series Hub Tuf-Lite II Fans H Hi Temp 3000HT Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II Hi Temp Fan Blades Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Hi Temp fan blades (Red) are

More information

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand INTRODUCTION A properly greased labyrinth seal will help prevent dust and water damage to the pedestal bearing oil supply and shaft seal area. Properly greased and oiled pedestals rarely require an overhaul.

More information

E4-WM5-Y542A00 MOUNTING INSTRUCTION

E4-WM5-Y542A00 MOUNTING INSTRUCTION This instruction is for both left front (driver) 41-269282 and right front (passenger) 41-269299 B8 8112 shocks. A step by step process is shown with images of the right front. The left front is a mirror

More information

Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS

Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized

More information

PRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit

PRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS

More information

SETTING UP THE MODEL 85B

SETTING UP THE MODEL 85B SETTING UP THE MODEL 85B SAFETY PRECAUTIONS FOR THE MODEL 85B System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During boring,

More information

1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A

1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A 1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

What is a fastener? A device to locate or hold parts

What is a fastener? A device to locate or hold parts What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how

More information

RELINER INSIDE DROP SYSTEM SPECIFICATIONS

RELINER INSIDE DROP SYSTEM SPECIFICATIONS 1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme

More information

Model: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5

Model: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5 SHEARER/PRESS BRAKE/ SLIP ROLL Model: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5 OPERATION MANUAL 1. USES This machine is used for shearing and bending low carbon plate (mild steel) or the other metal materials

More information

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981 Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to

More information

General Safety and Maintenance Manual

General Safety and Maintenance Manual General Safety and Maintenance Manual 4 H.P HORIZONTAL GRINDERS CAPACITY -6 Inch (150 mm) or 8 Inch (200 mm) Type 1 Wheels -Any Type 16, 17, 17R, 18 or 18R Cone Wheels w/ 5/8-11 Mounting 65H Series 4 H.P

More information

SETTING UP THE MODEL 210B

SETTING UP THE MODEL 210B SETTING UP THE MODEL 210B SAFETY PRECAUTIONS FOR THE MODEL 210B System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During boring,

More information

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub INSTALLATION MANUAL Hudson Tuf-Lite and Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 15 thru 20 Diameter Hudson Tuf-Lite (black) fan blades are made

More information

Table of Content. Machine Features and Functions. Specifications. Configuration and Working Principle 5. Machine Operation. Machine Adjustments

Table of Content. Machine Features and Functions. Specifications. Configuration and Working Principle 5. Machine Operation. Machine Adjustments Table of Content Safety Instructions Machine Features and Functions Specifications 2 3 4 Configuration and Working Principle 5 Machine Operation 7 Machine Adjustments 8 Machine Installation 9 Machine Remove

More information