600 CENTRE JUSTIFIES FANUC WIRE EDM INSTALLATION AT HASHIMOTO. Phil Slaymaker is one of five toolroom team leaders for Hashimoto s tooling repair
|
|
- Mabel Jemimah Gilbert
- 5 years ago
- Views:
Transcription
1 14 June CENTRE JUSTIFIES FANUC WIRE EDM INSTALLATION AT HASHIMOTO Phil Slaymaker is one of five toolroom team leaders for Hashimoto s tooling repair operation in Boldon, Tyne & Wear that provides fast response services to the likes of leading automotive operations Nissan, Honda, Toyota, Land Rover as well as to the UK build of the BMW Mini. While the original tooling tends to be developed by the parent company, the toolroom works a three shift system with responsibility for engineering changes, tool modification and repair services, and they are often working against the clock due to the prevention of roll-on effects which could lead to line stoppages in the customer s assembly operations. For this reason, equipment used has to be ultra-reliable but even more important is the back-up and service from the supplier when things go wrong. These two factors were high on the decision maker s check-off list when replacement wire cut EDM machines were sourced. Indeed, maintains Phil Slaymaker, influencing the decision to change to a Fanuc Alpha Robocut 1ic wire EDM and Joemars 430 FZY vertical EDM in December then follow these with a second but smaller Fanuc Alpha Robocut Oic in November from 600 Centre of Shepshed near Loughborough, were the track record and experiences of other customers of 600 Centre as well as the capabilities of the machines.
2 To date, he says our decision has been justified we produce lots of one-off components and bear in mind there can be 60 to 80 programs to prepare on a tool, and a new project is about to break that will involve over 140 different tools. We also have to support service requirements for tooling up to 10 years old which means we are exceedingly busy and cannot afford to be let down! While reliability and support are paramount, Hashimoto s toolroom has gained some important savings on cutting cycles by using the Fanuc machines compared to the previous machines installed. The automatic wire re-threading without having to drain the tank and the ability to avoid moving back to datum start position has proven to be a boon, and Phil Slaymaker confirms savings such as a 25 per cent cycle time reduction on profiling a 125 mm thick block that took some four hours previously. On extrusion die plates, the finishing capability of the machine means hand polishing is now dramatically reduced. Indeed, he adds, the surface finishes we obtain are never in question. So flexible and quick are the two Fanuc wire EDMs to program and run that we even use them for cutting-off anything that is from hardened material. In 10 mins we can cut-off hard material if, for instance, we have to change an angle on a die. At the other end of the spectrum, the longest job has taken two shifts to produce a complex die section when we roughed out the profile, removed the slug and finish taper cut the form.
3 Hashimoto was set up in Japan in 1917 as an automotive component manufacturer specialising in metal roll forming technology. Today it employs over 2,000 people with a turnover in excess of 400 million. The operation in Bolden was established in 1989 following the setting up of the Nissan car transplant business in Sunderland from which the company then progressively drew in other business from the UK automotive sector. Today with sales in the UK topping 25 million and 520 people including five Japanese employed, the company runs a series of process services including cold roll forming, stretch bending, coex extrusion, pressing and bending, injection moulding, extrusion and painted parts supply. The toolroom operation also provides a breakdown service, preventative and predictive maintenance support and services tooling including press tools, bolster plates, die sectors, drop-outs, guide dies and injection moulds up to 20 tonnes. Material processed in the toolroom include lots of tool steels, bronzes, AMPCO 18 and stainless steels. The Joemars vertical EDM was originally installed for repair of injection moulds and to carry out modifications but was quickly commandeered for punches, sparking clearance angles and for hole starting, to which Phil Slaymaker adds: It has proven to be so useful. The two Fanuc machines are key machines programmed using a CAMwrite package bought with the first Alpha 1iC from which programs are networked and downloaded. Sometimes we have a prove out on thin plate but in most cases we are so confident it s straight into production, adds Phil Slaymaker.
4 The Fanuc Alpha C Series of wire EDMs are available in the OiC version having a workpiece capacity of 650 mm by 450 mm by 180 mm and 500 kg table loading or in the large 1iC variant. This machine has a workpiece capacity of 830 mm by 730 mm by 300 mm and a one tonne table loading. Both machines feature the latest Fanuc 180 is-wb advanced control and, as Hashimoto s toolroom has found, this supports the world s fastest disconnection to reconnection automatic wire feed in just 12 secs using a thermal melting technique. This technique, that anneals the wire, improves the straightness and creates a very sharp edge at the point of cut. As this process can be activated while submerged in the tank on workpieces up to 100 mm thick, it significantly improves productivity and most important, as in the Hashimoto application, enables the toolroom personnel to carry on with other critical work while it is able to run in a limited or totally unmanned role. The machines also feature automatic hole search in the event of a short circuit which ensures the cycle picks up very close to the wire breakage point, saving time and avoiding the need for operator intervention. Quite a lot of Hashimoto work involves taper cutting for back-off and relief and here the Fanuc machines have a maximum taper angle of ± 30 o over 80 mm. As an option this can be increased to ± 45 o over 40 mm. Wire size as standard is 0.1 mm to 0.3 mm; Hashimoto uses 0.25 mm diameter brass wire but there is also an option to take this down to 0.05 mm.
5 Training was viewed as very important for the company s team and 10 people spent a week of intensive instruction at the 600 Centre. This is so important to our business that we are all fully aware of what can be done with the machines. Our job is to provide a fast turnaround service we never know what the next job will require in terms of response, he says. For further information, contact: David Wilkinson (Sales Director 600 Centre) Tel: +44 (0) Mike Wildish (Wildish Communications) Tel: +44 (0)
Manufacturing Processes (continued)
Manufacturing (continued) Machining Some other processes Material compatibilities Process (shape) capabilities Manufacturing costs Correct pg 142, question 34i should read Fig 6.18 question 34j should
More informationWire EDMing One-Piece Stamping Dies
8 121 Wire EDMing One-Piece Stamping Dies Blanking Die Wire EDM has made it possible to produce high quality dies from one piece of tool steel. This method of producing dies with wire EDM can result in
More informationProfiting with Wire EDM
3 Profiting with Wire EDM Users of Wire EDM 55 Parts made with the wire EDM process are used for machining conductive materials for medicine, chemical, electronics, oil and gas, die and mold, fabrication,
More informationELECTRIC DISCHARGE MACHINE
INTRODUCTION HISTORY AND DEVELOPMENT CLASSIFICATION OF MODERN MACHINING PROCESS PROCESS ELECTRICAL DISCHARGE MACHINE (EDM) CONSTRUCTION TYPES OF EDM SINKER EDM WIRE EDM ADVANTAGES AND DISADVANTAGES INTRODUCTION
More informationWire Electric Discharge (ED) Machining
Wire Electric Discharge (ED) Machining Tampere University of Technology Tuula Höök Wire electric discharge (ED) machining is based on the same principle as die-sink ED machining. The basic elements in
More informationMetal Working Processes
Metal Working Processes Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 CLASSIFICATION OF MANUFACTURING PROCESSES TOPIC OUTLINE What is Sheet Metal? Sheet Metalworking
More informationSeries GWIRE EDM FOR ULTRA PRECISE MACHINING
Series GWIRE EDM FOR ULTRA PRECISE MACHINING G Series Mechanical Structure Mono bloc Meehanite cast elements designed using Finite Element Methods (FEM) provide exceptional damping properties and exceptional
More informationULTRA PRECISION HARD TURNING MACHINES
ULTRA PRECISION HARD TURNING MACHINES Hembrug Machine Tools, with more than 50 years experience in the design, manufacturing and marketing of ultra precision, fully hydrostatic turning machines, Hembrug
More informationCorso di Studi di Fabbricazione
Corso di Studi di Fabbricazione 3a Richiami dei processi tecnologici di trasformazione FUNDAMENTAL OF METAL FORMING 1 METAL FORMING Large group of manufacturing processes in which plastic deformation is
More informationWire EDM Fundamentals
2 Wire EDM Fundamentals Revolutionizing Machining 35 Wire Electrical Discharge Machining (EDM) is one of the greatest innovations affecting the tooling and machining industry. This process has brought
More informationTrade of Toolmaking. Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 2: Blanking Tool (Unguided) Phase 2. Published by
Trade of Toolmaking Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 2: Blanking Tool (Unguided) Phase 2 Published by SOLAS 2014 Unit 2 1 Table of Contents Document Release History... 3 Unit Objective...
More informationEFFECT OF CRYOGENICALLY TREATED WIRE ON SURFACE ROUGHNESS IN WIRE EDM PROCESS
I J A M R Serials Publications 9(1) 2017 : January-June pp. 9-14 EFFECT OF CRYOGENICALLY TREATED WIRE ON SURFACE ROUGHNESS IN WIRE EDM PROCESS KULTAR SINGH SAINI 1 AND PARLAD KUMAR GARG 2* 1 Research Scholar,
More informationProduct information. QXD 200 Disc eroding machine for the complete processing of PCD tools. NEW: with automated polishing process for PCD-tips.
Product information QXD 200 Disc eroding machine for the complete processing of PCD tools. NEW: with automated polishing process for PCD-tips. - QXD 200 The idea. Increased productivity and secure future
More informationUnit IV Drawing of rods, wires and tubes
Introduction Unit IV Drawing of rods, wires and tubes Drawing is a process in which the material is pulled through a die by means of a tensile force. Usually the constant cross section is circular (bar,
More informationModule 3 Selection of Manufacturing Processes
Module 3 Selection of Manufacturing Processes Lecture 4 Design for Sheet Metal Forming Processes Instructional objectives By the end of this lecture, the student will learn the principles of several sheet
More informationProfiling press braking CNC MACHINING FABRICATION FINISHING
Profiling press braking CNC MACHINING FABRICATION FINISHING +44 (0)114 321 6303 enquiries@dnametalwork.com www.dnametalwork.com Profiling Bevel Capability up to 45 LASER cutting PLASMA cutting WATERJET
More informationWe offer a one stop shop service for small and medium size steel products manufacturing. sheet and tube laser and waterjet et cutting
We offer a one stop shop service for small and medium size steel products manufacturing. sheet and tube laser and waterjet et cutting bending, pressing and forming turning and milling welding - stainless,
More informationCOMPETENCY ANALYSIS PROFILE Tool and Die Maker 430A (All unshaded skill sets must be demonstrated/completed)
COMPETENCY ANALYSIS PROFILE Tool and Die Maker 430A (All unshaded skill sets must be demonstrated/completed) SKILL SETS SKILLS PROTECT SELF AND OTHERS Identify health and safety hazards. Wear, adjust,
More informationTOOL DESIGN - MANUFACTURING DESIGN SPECIFICATIONS FOR TOOLING AND EQUIPMENT SECTION H - DIE DESIGN TABLE OF CONTENTS. H.1 General...
TABLE OF CONTENTS H.1 General...Page 2 H.2 General Die Layout...Page 2 H.3 General Die Features...Page 2 H.4 Specific Die Type Features...Page 5 H.5 Special Punches and Die Bushings...Page 6 H.6 Wire E.D.M...Page
More informationRotary sizing of tube and pipe on the mill
Rotary sizing of tube and pipe on the mill By Bruce Chidlow, Kusakabe Electric & Machinery Co Ltd, Kobe, Japan Introduction The sizing methods used on tube and pipe mills have not changed significantly
More informationZHEJIANG TIANWEI MACHINERY CO.,LIMITED
ZHEJIANG TIANWEI MACHINERY CO.,LIMITED Product Catalogue 1.Edm wire wire cut cut 2.EDM DIE DIE SINKER 3.EDM DRILL 1.2 1.2 Company profile Our company apply ISO9001 quality system, and uses 8S for quality
More informationPREMIUM THIN TURRET TOOLING SYSTEM
Distribuitor: S.C. SM TECH S.R.L. www.smtech.ro www.wilsontool.ro office @ smtech.ro Tel: 0374991480 Tel mob: 0745528494 Fax: 0374091010 PREMIUM THIN TURRET TOOLING SYSTEM Strength. Performance. Innovation.
More informationWire EDM in a new dimension. The answer to future industrial standards
Wire Cut EDM 2 Wire EDM in a new dimension The answer to future industrial standards 3 4 You need the last µ in precision? You need surface qualities of 0.05 µ Ra? The completely new developed, innovative
More informationGreater accuracy and productivity through powerful new technology
Greater accuracy and productivity through powerful new technology BUILDING ON A TRADITION OF EXCELLENCE With many recent advances in software and hardware, jig grinding continues to play a critical role
More informationTechFront. Tooling Choices Lead to Thread Milling Solutions. of use of a particular tool. It can be more helpful
New Developments in Manufacturing and Technology Tooling Choices Lead to Thread Milling Solutions most people talk about the question of solution. When Apex switched to the Carmex mini mill-thread tool
More informationESPRIT ProfitMilling A Technical Overview
ESPRIT ProfitMilling A Technical Overview Contents ProfitMilling : What is it? Benefits to Manufacturers Traditional Roughing Limitations ProfitMilling Advantages Benefits of ProfitMilling Energy Consumption
More informationRoller Burnishing Tools
Roller Burnishing Tools The company DREX -TOOLS has since 1980 a great experience in the fields of the burnishing. The company, with the support of technical assistance with big experience has created
More informationCTR. Precision Engineering - Component part batch machining, multi stage press tooling, automated transfer systems, prototype work.
Folder UK new_network folder 16/11/2016 16:40 Page 2 MANUFACTURING Carbide Dies has over the years steadily established itself into the corporate entity it now sees itself operating as a modern, proactive,
More informationMANUFACTURING TECHNOLOGY
MANUFACTURING TECHNOLOGY UNIT II SHEET METAL FORMING PROCESSES Sheet Metal Introduction Sheet metal is a metal formed into thin and flat pieces. It is one of the fundamental forms used in metalworking,
More informationCALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 525 Interior Ladder Standard REV 0.0 7/19/04
BROWN MINNEAPOLIS TANK PAGE 1 OF 5 PURPOSE: Create, explain, and establish an interior ladder design standard, which will govern a BMT, supplied and/or installed typical interior ladder for welded steel
More informationElectrical Discharge Machining - Wire Cut. Presented and Arranged by: Khairu bin Kamarudin
Electrical Discharge Machining - Wire Cut Presented and Arranged by: Khairu bin Kamarudin Introduction EDM Wire Cut Machining method primarily used for hard metals or those that would be impossible to
More informationSimplified CAM for Advanced EDM Wire Cutting
Simplified CAM for Advanced EDM Wire Cutting A Technical Overview Contents Simplified Through Innovation... 2 Recognizing That EDM Part Shapes Are Unique... 2 Building Flexibilty Into a Wire Solution....
More informationHigh Feed Cutting HFC XFeed and XFeed-R. passion for precision
High Feed Cutting HFC XFeed and XFeed-R passion for precision XFeed and XFeed-R Specialists for high feed machining [ 2 ] The high feed end mills XFeed and XFeed-R were developed for the perfect execution
More informationMetal Stamping Glossary
Metal Stamping Glossary Alloy - A substance that has metallic properties and is composed of two or more chemical elements of which at least one is an elemental metal. Annealing - A process involving the
More informationME 333 MANUFACTURING PROCESSES-II SPECIAL PURPOSE METAL FORMING PROCESSES
ME 333 MANUFACTURING PROCESSES-II SPECIAL PURPOSE METAL FORMING PROCESSES Shape Rolling Steps in the shape rolling of an I-beam part. Various other structural sections, such as channels and rails, also
More informationYour Idea We Achieve
- 2015 - PRESENTATION Your Idea We Achieve www.camelengineering.com Overview Presentation 1. COMPANY PROFILE 2. MARKET SHARE & INDUSTRIES 3. PROJECTS MANAGEMENT PROCESS 4. EUROPE ENGINEERING LOCATION (AUSTRIA)
More informationBuilding Bridges Between R&D Institutions and Tool Making Sector (Slovene experiences)
11th International Cold Forming Congress 12th 14th September 2005 Chester, UK Building Bridges Between R&D Institutions and Tool Making Sector (Slovene experiences) Karl Kuzman University of Ljubljana,
More informationSTAR TOOL SUPPLY / GRAND TOOL SUPPLY
Made of hardened and tempered tool steel with ground points. es have knurled grip. Set consists of 1 each of 5 punches in plastic pouch. Point Size Length 1/16 3 3040004 5/64 4 3040005 3/32 4 3040006 9/64
More informationSANDVIK 20C STRIP STEEL
SANDVIK 20C STRIP STEEL DATASHEET Sandvik 20C is a hardened and tempered carbon steel characterized by good properties in respect of: Fatigue strength and wear resistance Hardness combined with ductility
More informationOperating manual. TruTool N 500 (1A1) english
Operating manual TruTool N 500 (1A1) english Table of Contents 1. Safety...4 1.1 General safety information...4 1.2 Specific safety information...5 2. Description...6 2.1 Correct use...7 2.2 Technical
More informationWhy Use. Pilot Assemblies. The New Industry Standard
Why Use Pilot Assemblies The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 01/17 - Rev. 11
More informationReview Label the Parts of the CNC Lathe
Review Label the Parts of the CNC Lathe Chuck Bed Saddle Headstock Cutting tool Toolpost Tailstock Centre Handwheel Cross Slide CNC Controller http://image.made-in- china.com/2f0j00zzftqvdrefoe/hobby-lover-metal-lathe-
More informationYour Innovative Partner for Machining & Fixturing Solutions.
Your Innovative Partner for Machining & Fixturing Solutions www.vertex-eng.co.uk The Company What We Do Vertex Engineering Solutions is a provider of low volume specialist components, fixture design and
More informationUNPACK & ASSEMBLY. Done! CAUTION! THE MILL WILL BE VERY HEAVY - GET ASSISTANCE Pepe Tools.
PARTS DIAGRAM T Bar Height adjustment Wooden hand grip Height adjustment gears Frame Height adjustment screws Top roller End Gears cover Handle Brass Bushes (Each side) Bottom roller 4:1 Gearbox Mounting
More informationOperating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher
Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand
More informationCorus Process Engineering (CPE) is heavily involved
Mould plate coatings for the 21st century The ceramic coating of slab caster moulds is realising significant benefits in terms of mould life, cast product shape and caster operating costs. It is now standard
More informationCONTENTS TABLE OF. Introduction. Company Details. Organization Chart. Certificates & Insurances. Our Products. List of machineries and Equipment
TABLE OF CONTENTS Introduction... 01 Company Details... 02 Organization Chart... 04 Certificates & Insurances... 05 Our Products... 10 List of machineries and Equipment... 31 Other Companies of Group...
More informationWire and tube Drawing
Wire and tube Drawing Drawing is an operation in which the cross-section of solid rod, wire or tubing is reduced or changed in shape by pulling it through a die. The principle of this procedure consist
More informationHolemaking Products & Accessories
Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy and consistency to get
More informationHigh-precision inch guide units Made in Germany
High-precision inch guide units Made in Germany cm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 cm inch inch 1 2 3 4 5 6 7 8 STEINEL All you need for tools Your partner for punching and bending
More informationSheet Metal Forming. Part 1
Sheet Metal Forming Part 1 Sheet Metal Forming For products with versatile shapes and lightweight Dates to 5000 B.C. Products include metal desks, file cabinets, appliances, car bodies, beverage cans Common
More informationStainless Steel Rotary Indexing Tables and A-Axes for Wire and Sinking EDM. Catalogue RE 4905
Stainless Steel Rotary Indexing Tables and A-Axes for Wire and Sinking EDM Catalogue RE 4905 Rotary Indexing Tables and A-Axes by HIRSCHMANN Pin point accuracy Controlled dynamic power Consistent performance.
More information- sprue gate - pinpoint gate - fan gate - tunnel gate
Moulds for processing of thermosetting moulding compounds 1. Sprue and Runner Systems and Gates Sprues should have either a round cross-section or a rounded trapezoidal construction and must have well-polished
More informationBUYER S GUIDE TO CONTROLLED TOLERANCE STAMPINGS
36 WAYS TO MAKE YOUR SHORT RUN STAMPING MORE ECONOMICAL BUYER S GUIDE TO CONTROLLED TOLERANCE STAMPINGS 7 TH EDITION Wrico Controlled Tolerance Stampings There Is A Difference! Wrico Does It Better A privately
More informationHBS-AP ASSEMBLING INSTRUCTIONS
ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK 97 HBS-AP ASSEMBLING INSTRUCTIONS 1. INTRODUCTION 1.1. This manual is very easy to consult and we recommend reading it before starting work,
More informationEWS made EDM Wire Cable e40
EWS made EDM Wire Cable e40 Made in Japan Why is e40 wire so popular? Made in Japan Total manufacturing (Melting to shipment) High quality Competitive price Quick action http://www.sodickews.com Japan
More informationPress Operations & Types of Dies
Press Operations & Types of Dies Press Working Use of mechanical and hydraulic presses for forging and extrusion has been mentioned earlier. Knuckle type mechanical presses are used widely for sheet metal
More informationChapter 22: Turning and Boring Processes. DeGarmo s Materials and Processes in Manufacturing
Chapter 22: Turning and Boring Processes DeGarmo s Materials and Processes in Manufacturing 22.1 Introduction Turning is the process of machining external cylindrical and conical surfaces. Boring is a
More informationIt s the small things in life that make the difference. We are in the job of making a difference. dietz.eu
It s the small things in life that make the difference. We are in the job of making a difference. dietz.eu Do what We have been working in the field of precision springs, wire and strip formed parts, assembly
More informationArchitectural Door & Cabinet Door
Architectural Door & Cabinet Door A1 TYDIX Flush Pulls TYDIX Flush Pulls are ground and polished to furnish a square, flat dress face usually free of blemishes. All outside edges and corners are clean
More informationMETAL TECHNOLOGIES A GENERATION AHEAD
METAL TECHNOLOGIES A GENERATION AHEAD THE LASER REVOLUTION Laser cutting has matured from a high-tech manufacturing process to a considerable common and popular manufacturing process today. Richinn Technology
More informationLOW-PROFILE ACCU-LENGTH CNC COLLET CHUCKS
LOW-PROFILE ACCU-LENGTH CNC COLLET CHUCKS High RPM All Royal CNC collet chucks are balanced by design for high-speed operation, and can often be run at higher speeds than conventional 3-jaw chucks because
More informationAN EXPERIMENTAL STUDY ON ROUNDNESS ERROR IN WIRE EDM FOR FERRO MATERIALS
AN EXPERIMENTAL STUDY ON ROUNDNESS ERROR IN WIRE EDM FOR FERRO MATERIALS S. Ajaya Kumar Asst. Prof. Department of Mechanical Engineering SVEC, Suryapet TS India ajayakumarme1971@gm ail.com DR.A.PRABHU
More informationHigh Precision Air Chucks
Precision Workholding Solutions High Precision Air Chucks www..com Improve productivity and lower the cost of secondary machining operations..... through high concentricity. Holding close concentricity
More informationUp to 5 3 from 5 to 10 4 from 10 to 18 6 from 18 to 35 8
Reamers They are the most used tools for the finishing holes. Can be divided into various categories, such as hand-reamers and those used in machine tools, reamers in highspeed steel, in carbide; inserted
More informationTrade of Toolmaking. Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 6: Jig Components Phase 2. Published by
Trade of Toolmaking Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 6: Jig Components Phase 2 Published by SOLAS 2014 Unit 6 1 Table of Contents Document Release History... 3 Unit Objective...
More informationDanly Die Sets CATALOG DIE SETS. Quality & performance Quick delivery Precision Components
Danly Sets TM CATALOG DIE SETS Quality & performance Quick delivery Precision Components 1 TM Danly Sets www.anchordanly.com CATALOG DIE SETS Service We Deliver and Quality You Can Depend On Danly Sets
More informationGerald Boggs' Wood Chisel
Gerald Boggs' Wood Chisel Wood Chisel By: Gerald Boggs, Virginia A couple of years ago, I journeyed over to the West Coast to spend some time working on wooden boats. I was required to bring a number of
More informationRenlaw COMPANY PROFILE INDUSTRIAL CUTTING TOOLS
AfricA s leading supplier of industrial cutting tools, food-processing and packaging blades, machine punches and dies COMPANY PROFILE OUR BUSINESS What do we do? is an engineering firm that specialises
More informationTrade of Toolmaking. Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 7: Injection Moulds Phase 2. Published by
Trade of Toolmaking Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 7: Injection Moulds Phase 2 Published by SOLAS 2014 Unit 7 1 Table of Contents Document Release History... 3 Unit Objective...
More informationTOOLS/ werkzeugtechnik
TOOLS werkzeugtechnik EDITORIAL In October 2006, ips-werkzeugtechnik took over the punching technology segment of DE-STA-CO Europe & Co. Werkzeugtechnik, which has earned us a new strategic position on
More informationPIPE & TUBE FABRICATION SERVICES CUSTOM BENDING LASER CUTTING END FORMING UNRIVALED EXPERTISE.
PIPE & TUBE FABRICATION SERVICES CUSTOM BENDING LASER CUTTING END FORMING UNRIVALED EXPERTISE www.sharpeproducts.com INDUSTRIES SERVED AUTOMOTIVE MEDICAL FURNITURE & FIXTURES FOOD & BEVERAGE AEROSPACE
More informationWire Drawing 7.1 Introduction: stock size
Wire Drawing 7.1 Introduction: In drawing, the cross section of a long rod or wire is reduced or changed by pulling (hence the term drawing) it through a die called a draw die (Fig. 7.1). Thus, the difference
More informationAKH FAS-NER SYSTEM. Joining Expertise with Technology. Joining Expertise with Technology. AKH Inc. AKH FASNER IN CROSS-SECTION A PROVEN SOLID JOINT
I N S E R T I O N P R E S S E S S E L F P I E R C I N G F L U S H A K H F A S - N E R S AKH FAS-NER SYSTEM AKH FASNER IN CROSS-SECTION Since 1981, AKH has provided the engineering and manufacturing support
More informationOperating Instructions For Lockformer Button Punch Flanger
Capacity: 20 to 28 Gauge Galvanize Operating Instructions For Lockformer Button Punch Flanger To satisfactorily form the 90º button punch flange on light gauge materials, it was necessary to form the metal
More informationVertical Machining Center V.Plus-550
Vertical Machining Center V.Plus-550 V.Plus-550 Pioneers of the Vertical MC Matsuura Pioneering Machine Tool Excellence Since 95 Pioneers in the development and manufacture of high quality CNC vertical
More informationMetals can be bought from suppliers in standardized forms and sizes, such as round,
1.4 METAL CUTTING BAND SAWS: Metals can be bought from suppliers in standardized forms and sizes, such as round, rectangular or square bar stock or in the form of large sheets (plates). Bar stock normally
More informationPRECISION 100% 90% 80% 70% 60% 50% 40% 30% 20% SPEED 10% PLEXITY SURFACE FINISH. Certified wires
PLEXITY Certified wires Did you know? Using non-certified consumables or counterfeit parts can reduce the performance of EDM machining tools by up to! The competitiveness of your machine depends on the
More informationNORTH AMERICA ONLY GENERAL INFORMATION SCRAP SHEDDING ON DIES
GENERAL INFORMATION SCRAP SHEDDING ON DIES 1. CAST S FOR NOISE REDUCTION SEE W-DX5-58M PAGE 5. ALL S, ARE TO BE DESIGNED WITH A PREFERRED SHEDDING ANGLE OF 30 DEGREES, REACHING TO THE EDGE OF THE DIE.
More informationFUNDAMENTAL MANUFACTURING PROCESSES. Sheet Metal Stamping Dies & Processes-SD
FUNDAMENTAL MANUFACTURING PROCESSES Sheet Metal Stamping Dies & Processes-SD SCENE 1. SD20A, CGS: Dies & Die Functions white text, centered on background FMP BKG, motion background SCENE 2. SD20A, SME4311,
More informationSTEEL RULE. Stock TRY SQUARE
FITTING INTRODUCTION Fitting consists of a handwork involved in fitting together components usually performed at a bench equipped with a vice and hand tools. The matting components have a close relation
More informationListed below are some of our most common drill designs used in many various aerospace applications:
www.lomas.co.uk Tools can be manufactured in 3 material choices for use on composites: Solid Tungsten Carbide Tooling CVD Diamond Coated Solid Tungsten Carbide Polycrystalline Diamond (PCD) LOMAS design
More informationSheet metal processing center EML Z-3510 NT EML Z-3610 NT
Sheet metal processing center EML Z-3510 NT EML Z-3610 NT Punching technology Laser technology The new sheet metal processing center EML Z a triad of speed, flexibility and productivity The decisive answer
More informationPress Information
Press Information 07.12.2017 Integrated Rotating/Indexing Spindle Offers New Processing Capabilities Friedrich Erodierservice GmbH expands existing system with a HIRSCHMANN rotating and indexing spindle
More informationContents CUT 2000 CUT Digital lpg generator CNC Vision 5 Autonomy and automation GF AgieCharmilles
CUT 2000 CUT 3000 2 < Contents Highlights Mechanics Wire guidance Automatic wire changer 4 6 8 12 Digital lpg generator CNC Vision 5 Autonomy and automation GF AgieCharmilles 13 14 16 18 CUT 2000 CUT 3000
More informationPrecision Chucks for Improved Accuracy and Increased Productivity
Precision Workholding Technology Precision Chucks for Improved Accuracy and Increased Productivity Precision Air Chucks (Self Contained Design) MicroCentric Precision Air Chucks feature a patented open
More information4 + 5!" ENGINE BLOCK CRANKSHAFT CAMSHAFT KNUCKLE CONROD BEARING CAP 16+17!
4 + 5!" 6 + 7 8 + 9 10+11 12+13 14+15 16+17! 18+19 20+21! 22+23!" 24+25! 26+27 INGERSOLL!"#$%&' 4 + 5 ENGINE BLOCK 6 + 7 CRANKSHAFT 8 + 9 CAMSHAFT 10+11 KNUCKLE 12+13 CONROD 14+15 BEARING CAP 16+17 EXHAUST
More informationCOMPETENCY ANALYSIS PROFILE MOULD MAKER 431A (All unshaded skill sets must be demonstrated/completed)
COMPETENCY ANALYSIS PROFILE MOULD MAKER 431A (All unshaded skill sets must be demonstrated/completed) SKILL SETS SKILLS PROTECT SELF AND OTHERS Identify health and safety hazards in the workplace. Wear,
More informationMetal Cutting Processes 1 - Turning
You are here: Home > Handout > Metal Cutting Processes 1 - Turning Metal Cutting Processes 1 - Turning Contents 1. Introduction 2. Center Lathe 3. Cutting Tools 4. Basic Matel Cutting Theory 5. Tool Angles
More informationKestrel Aluminium Systems Limited. Product Manual Section 11 Thermal Framing System - Fabrication. Manual Version
Limited Product Manual Section 11 - Fabrication Manual Version 23.0.1 Section 11.01 Fabrication 11.01.01 sheet 1 General guidelines for cutting and bar preparation Section 11 Contents Section 11.02 Fabrication
More informationIII YEAR/VI SEMESTER UNIT III ELECTRICAL ENERGY BASED PROCESSES
Department Of Mechanical III YEAR/VI SEMESTER UNIT III ELECTRICAL ENERGY BASED PROCESSES 8 Electric Discharge Machining (EDM)- working Principle-equipments-Process Parameters- Surface Finish and MRR- electrode
More informationModel: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5
SHEARER/PRESS BRAKE/ SLIP ROLL Model: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5 OPERATION MANUAL 1. USES This machine is used for shearing and bending low carbon plate (mild steel) or the other metal materials
More information3E RP Presentation-2018
3E RP Presentation-2018 www.3erp.com The "3-E" Difference Excellence in Precision Efficiency in Production Economically Priced CONTENT WHO IS 3ERP 3ERP TODAY 3ERP MISSION CORE CAPABILITIES CNC MACHINING
More informationHow to use. Use example. Non-scratch sheet prevents die marks. Tight-knit super fiber provides a working life of many hundreds cycles.
How to use Small to Medium dies Fix Kizu-non on the die shoulder with masking tape. Should not be crinkled. *Cut Kizu-non with scissors for desired length. Large dies Fix Kizu-non on each die shoulders.
More informationTrade of Toolmaking. Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 5: Jigs and Fixtures Phase 2. Published by
Trade of Toolmaking Module 5: Press Tools, Jigs & Fixtures, Mouldmaking Unit 5: Jigs and Fixtures Phase 2 Published by SOLAS 2014 Unit 5 1 Table of Contents Document Release History... 3 Unit Objective...
More informationdesign and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses
design and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses UPH 28 Horizontal hydraulic press - Built-in memory makes it possible to save up to 4 bending
More informationSliding Headstock Type Automatic CNC Lathe R04/R07-VI. "Evolution and Innovation" is the Future
Sliding Headstock Type Automatic CNC Lathe R04/R07-VI "Evolution and Innovation" is the Future Cincom R04/R07-VI Extremely fast, ultra-high precision, highly efficient The smaller the parts, the more experience
More informationENHANCEMENT OF MATERIAL REMOVAL RATE BY USING CRYOGENICALLY TREATED WIRE IN WIRE EDM PROCESS
I J A M R Serials Publications 9(1) 2017 : January-June pp. 1-7 ENHANCEMENT OF MATERIAL REMOVAL RATE BY USING CRYOGENICALLY TREATED WIRE IN WIRE EDM PROCESS KULTAR SINGH SAINI 1 AND PARLAD KUMAR GARG 2*
More informationINTRODUCTION. Dear Business Partners,
INTRODUCTION Dear Business Partners, We are proud to issue the new catalogue of STROJFERR s.r.o. which was established in 1997 as a genuinely Czech company. In its activities and production programme,
More informationVSeries. A Wire EDM to Excelsior Precision
VSeries A Wire EDM to Excelsior Precision Excelsior from Pr Excetek was founded by a prominent team in the field of Wire Cutting EDM. We especially incorporate with Japanese Wire EDM technologies; a well-known
More information