Type A Type B Type C Type D

Transcription

1 plywood plywood plywood plywood Type Type Type Type D Note: Type and cutout are flush with frame Type and D cutout are offset to accommodate French Door with trim around the glass. Type E and F (not shown above) are cutouts with batten on the back of the panel. Helpful Tips: L frame is preferred for French Door Installation. There will be approximately 1 gap between the edge of the handle and cutout for handle or 2.5 gap between edge of knob and cutout for round knob. If cutout will be over glass area then light can come through cutout area. In this case, back of frame will be routed and ¼ " thick plywood will be placed in cutout area. Please provide maximum frame-to-frame measurement for shutter size. 1/10

2 TYPE URVE FLUSH UTOUT- With Handle and Lock Position F E 1/4 "thick 1/4" thick G D DI1 DI 2 DI 3. ottom of L frame to center of handle pivot.. Edge of L frame to center of handle pivot.. End of handle to center of handle pivot. D. ottom of L frame to center of lock. E. Edge of L frame to center of lock. F. enter of Lock to top edge of lock base plate. G. enter of handle pivot to edge of handle base plate. H. Is the handle on left or right side of the door? I. Is frame with cutout-block required? If the base plate is square (see DI 3), then please provide following information: J. Square base plate height. K. Square base plate width. L. ottom of L Frame to ottom of the Square ase Plate. * If your French door does not have a lock, please write N/ on D, E, and F. * utout-block piece will be made according to DI 2 if handle or lock base plate can hit cutout-block piece, otherwise piece will be made according to DI 1. 2/10

3 TYPE URVE FLUSH UTOUT-Exact utout Position 1/4" thick D 1/4" thick DI 1 DI2. ottom of L frame to bottom edge of cutout.. ottom of L frame to top edge of cutout.. Depth of cutout. D. Outside edge of L frame to edge of cutout-block. E. Is the handle on left or right side of the door? F. Is frame with cutout-block required? If cutout-block piece will not hit the handle base plate, the value of D should be zero. (DI1) If cutout-block piece might hit the handle base plate, please provide measurement D. (DI2) 3/10

4 TYPE URVE OFFSET UTOUT- With Handle and Lock Position E 1 1/2 Top view of the cutout section D F DI 1 DI 2 DI 3. ottom of L frame to center of handle pivot.. Edge of L frame to center of handle pivot.. End of handle to center of handle pivot. D. ottom of L frame to center of lock. E. Edge of L frame to center of lock. F. enter of Lock to top edge of lock base plate. G. Projection of trim. H. Is handle on left or right side of the door? I. Is frame with cutout-blocked required? If the base plate is square (see DI3), then please provide following information: J. Square base plate height. K. Square base plate width. L. ottom of L Frame to ottom of the Square ase Plate. utout-block piece will not go up to outside edge of L frame. It will go up to inside edge of L frame only. (DI 1) 4/10

5 TYPE URVE OFFSET UTOUT-Exact utout Position 1 1/2 DI 1 Top view of the current cutout section. ottom of L frame to bottom edge of cutout.. ottom of L frame to top edge of cutout.. Depth of cutout. D. Projection of trim. E. Is the handle on left or right side of the door? F. Is frame with cutout-block required? utout-block piece will not go up to outside edge of L frame. It will go up to inside edge of L frame only. (DI 1) 5/10

6 TYPE RETNGULR FLUSH UTOUT D DI 1 DI 2. ottom of L frame to bottom edge of cutout.. ottom of L frame to top edge of cutout.. Depth of cutout. D. Outside edge of L frame to edge of cutout-block. E. Is the handle on left or right side of the door? FRENH DOOR UTOUT TYPE D RETNGULR OFFSET UTOUT F. Is frame with cutout-block required? If cutout-block piece will not hit the handle base plate, the value of D should be zero. (DI 1) If cutout-block piece might hit the handle base plate, please provide measurement D. (DI 2) 6/10

7 TYPE D RETNGULR OFFSET UTOUT 1 1/2 DI 1 Top view of the current cutout section. ottom of L frame to bottom edge of cutout.. ottom of L frame to top edge of cutout.. Depth of cutout. D. Projection of trim. E. Is the handle on left or right side of the door? F. Is frame with cutout-block required? utout-block piece will not go up to outside edge of L frame. It will go up to inside edge of L frame only. (DI 1) 7/10

8 TYPE E & F Type E Type F Type E*: Shutter with 60 angle cutout. Panel sits o n batten. Type F*: Shutter with rectangular cutout. Panel sits on batten. oth Type E and F come with ullnose edges around stiles and rails. atten Size: Louver Size atten Projection atten Width 1 1/4 1 7/8 2 1/ /2 1 3/8 3/4 4 1/2 1 7/8 For matching panels without cutout, please specify Match French Door utout Type E / F in the special instruction. 20% surcharge applies. 8/10

9 FRENH DOOR TYPE E G Max frame to frame measurement only atten Size: Type E: height () and depth () of cutout Louver Size atten Projection atten Width 1 1/4 1 7/8 2 1/ /2 1 3/8 4 1/2 1 7/8 = Height of 60 angle cutout = ottom of panel to center of cutout 3/4 = Depth of cutout D = Projection of trim E = Is the handle on the left or right side of the door? F = atten Projection G = Outside edge of atten to edge of cutout-block 8 1/2 2 1/2 9 1/2 3 1/ / /2 13 1/2 4 1/2 For matching panels without cutout, please specify Match French Door utout Type E / F under special instruction. 20% surcharge applies. 9/10

10 FRENH DOOR TYPE F G Max frame to frame measurement only atten Size: Louver Size atten Projection atten Width 1 1/4 1 7/8 2 1/ /2 1 3/8 3/4 4 1/2 1 7/8 = Height of rectangular cutout = ottom of panel to center of cutout = Depth of cutout D = Projection of trim E = Is the handle on the left or right side of the door? F = atten Projection G = Outside edge of atten to edge of cutout-block For matching panels without cutout, please specify Match French Door utout Type E / F in the special instruction. 20% surcharge applies. 10/10