High Performance CADDY CAT HP

Size: px

Start display at page:

Download "High Performance CADDY CAT HP"

Rudolph Hodges
5 years ago
Views:

1 High Performance CADDY CAT HP J-Hook Assemblies Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Retainer Installation Features: - Each assembly comes with a retainer. - The CAT64HP holds 4-pair UTP cables; 300 Cat.5/5e or 300 fiber optic cables, or 185 Cat.6 cables. - Provides strain relief and routes cables. Bend radius conforms to ANSI/TIA D standard. - Complies with UL, cul, and NEC requirements for structured cabling systems - Complies with ANSI/TIA-569-D WARNING: 1. Pentair products shall be installed and used only as indicated in Pentair product instruction sheets and training materials. Instruction sheets are available at and from your Pentair customer service representative. 2. PENTAIR products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 3. All instructions must be completely followed to ensure proper and safe installation and performance. 4. Improper installation, misuse, misapplication or other failure to completely follow Pantair's instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death, and void your warranty. 5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any other purpose. NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted. The customer is responsible for: a. Conformance to all governing codes. b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer. c. Using appropriate industry standard hardware as noted above. SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application. 1 OF Pentair All Rights Reserved

2 Angle Brackets Part CAT16HPAB CAT21HPAB CAT32HPAB CAT48HPAB CAT64HPAB angle bracket -1/4" [6] mounting hole Fig. 1 1) Position CATHPAB onto joist, wall or concrete 2) Secure with appropriate fastener Beam Clamp Part CAT16HPBC CAT21HPBC CAT32HPBC CAT48HPBC CAT64HPBC screw-on bracket - 1/8" [3] thru 1/2" [13] flange Part CAT16HPBCB CAT21HPBCB CAT32HPBCB CAT48HPBCB screw-on bracket - 1/8" [3] thru 1/2" [13] flange - rotates 360º CAT64HPBCB ) Place on beam and tighten screw securely (Approximately 20 in. lbs. torque) 2 OF Pentair All Rights Reserved

3 Flange Mount Clip 4 1) With hammer, tap clip onto flange 9 2) Place cables in J-hook Part CAT16HP CAT21HP CAT32HP CAT48HP CAT64HP CAT16HP CAT21HP CAT32HP CAT48HP CAT64HP CAT16HP CAT21HP CAT32HP CAT48HP CAT64HP CAT16HP24SM CAT21HP24SM CAT32HP24SM CAT48HP24SM CAT64HP24SM CAT16HP58SM CAT21HP58SM CAT32HP58SM CAT48HP58SM CAT64HP58SM CAT16HP912SM CAT21HP912SM CAT32HP912SM CAT48HP912SM CAT64HP912SM hammer-on - 1/8" thru 1/4" flange - rotates 360º hammer-on - 5/16" thru 1/2" flange - rotates 360º hammer-on - 9/16" thru 3/4" flange - rotates 360º hammer-on - 1/8" thru 1/4" flange hammer-on - 5/16" thru 1/2" flange hammer-on - 9/16" thru 3/4" flange Drop Wires, Rods and Flanges 5 Part CAT16HP4Z CAT21HP4Z CAT21HPWH4Z34 - CAT32HP4Z CAT48HP4Z34 - CAT64HP4Z34 - CAT16HP6Z CAT21HP6Z CAT32HP6Z CAT48HP6Z34 - CAT64HP6Z34 - CAT16HP8Z34 - CAT21HP8Z34 - CAT32HP8Z34 - CAT48HP8Z34 - CAT64HP8Z34-5 4Z34 - #12 thru 1/4" wire, plain or threaded rod 6Z34-3/8" plain or threaded rod 8Z34-1/2" [13] or 5/8" [16] threaded rod Smooth Rod Threaded Rod N/A N/A ) Squeeze fastener 2) Connect top edge over wire 3) Twist into place 4) Release 5) Place cables in J-hook 3 OF Pentair All Rights Reserved

4 Floor Pedestal Support Part CAT16HPCD1B CAT21HPCD1B CAT32HPCD1B CAT48HPCD1B CAT64HPCD1B under floor support to pedestal Use only for Flexible conduits/cables 6 1) Position clip on pedestal 2) Tighten screw through clip with 75 in-lb torque. 3) Place cables in J-hook Part CAT16HPBC CAT21HPBC CAT32HPBC CAT48HPBC CAT64HPBC CAT16HPBC200B CAT21HPBC200B CAT32HPBC200B CAT48HPBC200B CAT64HPBC200B screw-on bracket - 1/8" [3] thru 5/8" [16] flange screw-on bracket - 1/8" [3] thru 5/8" [16] flange - rotates 360º 7 8 1) Place on beam and tighten screw securely (Approximately 20 in. lbs. torque) 4 OF Pentair All Rights Reserved

5 10 11 Part CAT16HPAF CAT21HPAF CAT32HPAF CAT48HPAF CAT64HPAF CAT16HPVF CAT21HPVF CAT32HPVF CAT48HPVF CAT64HPVF AF14 1/16" [2] thru 1/4" [6] angled flange VF14 1/16" [2] thru 1/4" [6] vertical flange 1) With hammer, tap clip onto flange Purlin Part CAT16HP CAT21HP CAT32HP CAT48HP CAT64HP /16" [2] thru 3/32" [2] angled flange Fig. 12 1) Hand push clip onto flange Strut Part CAT16HPESC CAT21HPESC CAT32HPESC ESC channel strut Fig Position clip onto strut. Rotate downwards until secure on strut. 5 OF Pentair All Rights Reserved

Part CAT16HPBC26 181163 CAT21HPBC26 181164 CAT32HPBC26 181165 CAT48HPBC26 181166 CAT64HPBC26 181167 14 BC26 1/8" [3] thru 1/2" [13] flange Fig.

6 Part CAT16HPBC CAT21HPBC CAT32HPBC CAT48HPBC CAT64HPBC BC26 1/8" [3] thru 1/2" [13] flange Fig Place on beam and tighten screw securely (Approximately 40 in. lbs. torque) Place cables in J-hook 6 OF Pentair All Rights Reserved

STEEL C-CLAMP WITH LOCKNUT

FIG. 250 STEEL C-CLAMP WITH LOCKNUT Function: Designed for attaching hanger rod to the bottom flange of a beam. The hanger rod should make contact with the beam flange to ensure full engagement. Material: