Panduit Cross Connect System
|
|
- Valentine Wiggins
- 6 years ago
- Views:
Transcription
1 Panduit Cross Connect System Part Numbers: PXMT300, PXMT50, PXPCB4, PXPCB5, PXDR, PXLK-VI Panduit Corp INSTALLATION INSTRUCTIONS This product is to be installed in a secured location per TIA standards. Tools Needed: PXPCB4 CWST PXDR PXPCB5 CJAST PDT110 PXMT300 PXMT50 PXLK-VI Punchdown Tool PDT110 with Cross Connect Blade (not supplied by Panduit) Cross Connect Layouts Draw Position Lines on Wall or Mounting Surface Draw lines as shown in Fig. 1 to guide placement of the first base. Use a level and measure the shown distances. Fig. 1 TOP Mounting the First Base Align the base with the position lines and fasten the base to the wall using #8-3/4" wood screws. #8-3/4" wood screws When using a false wall, cut out holes before installing the bases. Fig. 2 Page 1 of 8
2 Base 1 Rings Base 2 Attachment of Addition Bases Engage the second base into the first base using two rings. Secure the second base using #8-32" wood screws. Horizontal and vertical rings should be used to position additional bases. Additional bases and rings should be installed as needed per typical industry practices. Fig. 3 Secure rings with wood screws where needed. Fig. 4 4-Pair Cable Installation (See page 6 for 25-Pair Cable Installation) Tak-Ty Hook & Loop Cable Tie Routing the Cables Start by routing the cable bundle for the lower base. Attach the bundle to the center cable mount on the right side of the upper base using a Tak-Ty Hook & Loop Cable Tie. Fig. 5 Page 2 of 8
3 Tak-Ty Hook & Loop Cable Tie Route the upper base cable bundle next. Using a Tak-Ty Hook & Loop Cable Tie, secure both upper and lower cable bundles at the top cable mount location as shown. Fig. 6 Connector Block Termination Snap connector block into the second position from the top of the upper base. Orient the connector by aligning the color code shown below. Color code WH/ BU WH/ OR BU OR WH/ GR GR WH/ BR BR Fig. 7 Pair 1 Color code Pair 24 Blank pair Spread out each cable to the correct connector location. While keeping the cable tight to the connector locations, mark each cable. This will be the mark to strip the cable jacket to in the next step. Fig. 8 Page 3 of 8
4 Using the CJAST tool, strip each cable to the marks you made in the previous step. Using the CWST tool, trim off the excess strength member and rip cord. Fig. 9 CJAST CWST Position conductors over the pair splitter into the connector slots with matching color code. Color code WH/ BU WH/ OR BU OR WH/ GR GR WH/ BR BR Fig. 10 Punchdown each conductor using punchdown tool. Properly orient the tool blade so the cutting edge is on the bottom as shown. Fig. 11 PDT110 Cutting blade edge Cross Connect Blade (not supplied by Panduit) Remove connector block, rotate, and place into the top position of the base. Fig. 12 Page 4 of 8
5 Place the next connector block into the third position down from the top and terminate as previously described. After terminated, rotate the connector block up into the second position from the top. Repeat this process for remaining connector blocks and cables. Fig. 13 Labeling and Cross Connect Wiring Mark identification labels. Apply label to the front face of the label holder. Install label holders onto the base. Label holders snap into position between upper and lower connector blocks as shown. Label Holder Label Fig. 14 Install cross connect wires according to the engineering work plan. Route wires through the horizontal rings to the second location leaving 3" of slack. Wire ends should always face towards the label. Page 5 of 8
6 Slack 25-Pair Cable Installation (See page 2 for 4-Pair Cable Installation) Fig. 15 NOTE: The following procedure is a quick and simple method for installing high performance data cable. Traditional installation methods are also acceptable; however, the following steps must be utilized. 1. Place a cable tie through the slot on the connector block. 2. Leave approx 7" of wire slack from the end of the cable sheath to the cable tie. 3. Lay the bundle along the top of the connector block as shown and lightly fasten the cable tie. Leave approx 50% space. 4. After termination, dress the wire bundle in the space between the connectors and into the back of the base as needed. Tak-Ty Hook & Loop Cable Tie Routing the Cables Start by routing the cable bundle for the lower base. Attach the bundle to the center cable mount on the right side of the upper base using a Tak-Ty Hook & Loop Cable Tie. Fig. 16 Tak-Ty Hook & Loop Cable Tie Route the upper base cable bundle next. Using a Tak-Ty Hook & Loop Cable Tie, secure both upper and lower cable bundles at the top cable mount location as shown. Fig. 17 Page 6 of 8
7 Locate the appropriate cable from the center of the base. Trim off a small portion of the jacket to expose the rip cord. Pull the rip cord until the slit is level with the first position of the upper base as shown. Remove excess jacket and rip cord. Fig. 18 Install connector block into the second position from the top of the upper base. Left side Pair 1 Pair 25 Fig. 19 Insert wires per engineering work plan. Punchdown each conductor using punchdown tool. Properly orient the tool blade so the cutting edge is on the bottom as shown. Fig. 20 PDT110 Cutting blade edge Cross Connect Blade (not supplied by Panduit) Remove connector block, rotate, and place into the first position of the base. Fig. 21 Page 7 of 8
8 Lower the trim line to the second position from the top of the base and strip the cable. Fig. 22 Place next connector block in the third position down from the top of the base and terminate as previously described. After terminated, rotate the connector block up into the second position. Repeat steps for remaining connectors and cables. Fig. 23 Labeling and Cross Connect Wiring Mark identification labels. Apply label to the front face of the label holder. Install label holders onto the base. Label holders snap into position between upper and lower connector blocks as shown. Label Holder Label Install cross connect wires according to the engineering work plan. Route wires through the horizontal rings to the second location leaving 3" of slack. Wire ends should always face towards the label. Fig. 24 For Instructions in Local Languages and Technical Support: Page 8 of 8 techsupport@panduit.com Phone:
OPTICOM Rack Mount Fiber Cassette Enclosure
OPTICOM Rack Mount Fiber Cassette Enclosure Part Number: FCE4U Panduit Corp. 2008 INSTALLATION INSTRUCTIONS FCE4U Contents: 1 - ENCLOSURE 4 - #12-24 X 1/2" SCREWS 4 - M6X1 SCREWS 2 - #10-32 X 3/8" SCREWS
More informationP/N LED LIGHT FI85 RETROFIT KIT INSTRUCTIONS
P/N 090521 LED LIGHT FI85 RETROFIT KIT INSTRUCTIONS 1 4 7 10 11 2 5 8 6 9 12 3 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 3 090503 1 METER EXTENSION 2 3 090543 18 LED BULB STRIP (12 IN.)
More information6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets
6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets Panduit Corp. 2016 INSTALLATION INSTRUCTIONS Page 1 of 36 Component Guide for Doors Dual Sliding Containment Door
More informationCOWO. Customer Wall Outlet. 1 General. 2 Kit content. 3 Handling of the box. TC-1203-IP Rev A, Apr
COWO I N S T A L L A T I O N I N S T R U C T I O N TC-1203-IP Rev A, Apr 2017 www.commscope.com Customer Wall Outlet 1 General Customer Wall Outlet 2 Fiber for max. 2 bend reduced fibers, 2 SC-adapters
More informationInstallation Guidelines, 10Gig SFP+ Direct Attach Copper Cable Assembly PN533A
Installation Guidelines, 10Gig SFP+ Direct Attach Copper Cable Assembly Introduction As virtualization, consolidation, and convergence initiatives continue to expand in Data Centers, so do the demands
More informationInstruction Sheet Tool Kit [ ] (for SL Series 110 Jack Connectors)
Instruction Sheet Tool Kit 1725150 [ ] (for SL Series 110 Jack Connectors) 26 FEB 04 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
More informationP/N LED LIGHTS 6509/9012/12012 MACHINES
P/N 090517 LED LIGHTS 6509/9012/12012 MACHINES 4 1 8 12 5 9 13 2 6 10 3 7 11 14 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 18 IN. 660461 18/2 SVO CORD 2 1 090508 LED LIGHT TRANSFORMER 3
More informationProduct Bulletin. Quick-Build Harness Board System
Product Bulletin Quick-Build Harness Board System A Revolutionary Modular Solution for Harness Manufacturers The modular, reusable solution consists of 1' X 1' (305mm x 305mm) grid tiles and specially
More informationProduct Bulletin. Quick-Build Harness Board System
Product Bulletin Quick-Build Harness Board System A Revolutionary Modular Solution for Harness Manufacturers The modular, reusable solution consists of 1 X 1 (305mm x 305mm) grid tiles and specially designed,
More informationFiber Splice Box (FSB-D) Installation Instructions
Fiber Splice Box (FSB-D) Installation Instructions Table of Contents General Product Information... 1.0 Safety Precautions... 2.0 Tools Required... 3.0 Package Contents... 4.0 Installing the Product Unpacking...
More informationProduct Bulletin. Quick-Build Harness Board System
Product Bulletin Quick-Build Harness Board System A Revolutionary Modular Solution for Harness Manufacturers The modular, reusable solution consists of 1' X 1' (305mm x 305mm) grid tiles and specially
More informationLCD LIFT Flat Panel Display System Installation Manual. Table of Contents
LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More information2. Multiplexer assembly
2. Multiplexer assembly Written By: Josef Prusa 2017 manual.prusa3d.com Page 1 of 12 Step 1 Prepare the parts Take the bags labeled as "2. Multiplexer" Step 2 Parts identification Y-splitter Extruder-adaptor-MM
More informationShannon s CCR Spiral Tree
Shannon s CCR Spiral Tree http://www.shannonclaus.com Disclaimer: I take no responsibility for design failures or injuries related to this design. This document is created for informational purposes only
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More information4200 JSP, KSP, LSP and MSP Cabinets
4200 JSP, KSP, LSP and MSP Cabinets Instructions May 1995 Issue 1, 34-7037-9012-0 1 2 Contents: 1.0 General... 4 2.0 Description of Cabinets... 4 3.0 Accessories and Optional Cross Connect Test Probes...
More informationP/N LED LIGHT 505EC RETROFIT KIT INSTRUCTIONS
P/N 090513 LED LIGHT 505EC RETROFIT KIT INSTRUCTIONS 1 4 7 12 8 2 5 13 9 11 14 3 6 10 15 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 18 IN. 660461 18/2 SVO CORD 2 1 090508 LED LIGHT TRANSFORMER
More informationOptical Cable Entry Facility (OCEF) Installation Instructions
Instruction Sheet 860380690 Uniprise Solutions Optical Cable Entry Facility (OCEF) Installation Instructions General The Optical Cable Entry Facility (OCEF) cabinets store optical fiber splices between
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationM4800 and M4800A Patch Panel Instructions
Instruction Sheet 860462118 M4800 and M4800A Patch Panel Instructions General The M4800 and M4800A modular panels are highly flexible 48-port patch panel assemblies available in GigaSPEED, PowerSUM, or
More informationTMA812 Tilt Mount Adapter for NEAR A8 and A12 Loudspeakers Installation Instruction Manual
TMA812 Tilt Mount Adapter for NEAR A8 and A12 Loudspeakers Installation Instruction Manual 50 Spring Street, Ramsey, NJ 07446 USA Tel. 201-934-8500 Fax: 201-934-9832 www.bogen.com Specifications subject
More informationWiring Techniques for Wiring a Lamp
Supplies and Tools that you will need: Provided in your kit: Polarized lamp plug, 9 of SPT-1 18 AWG parallel lamp cord, bushings and grommets Items that you will need to provide: Phillips screwdriver,
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R
INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R I. SUSPENDED INSTALLATIONS 1. Lay the two track halves on the floor with
More informationBel Stewart Connector
Page 1 of 8 PLUG ASSEMBLY INSTRUCTIONS FOR Cable with INDIVIDUALLY SHIELDED PAIRS (PIMF or SFTP) T568B Wiring Pattern For Cable with Overall Foil Shield (FTP), See Page 9 1 2 Cut cable to length. If you
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More informationPing Pong Ball Launcher. Version 3.0 New Matter, 2016 Part number: 11069
Ping Pong Ball Launcher Version 3.0 New Matter, 2016 Part number: 11069 Hardware needed to complete this project: Size Length Used Label Screw, Type 25, Phillips Pan head, Thread Cutting #4 0.375 29 A
More informationInstallation Guide. Capped Cellular PVC Fencing. Table of Contents. Storage and Handling Tools Needed Fence Layout and Locating Posts
Capped Cellular PVC Fencing Installation Guide Table of Contents Storage and Handling Tools Needed Fence Layout and Locating Posts Installation instructions 4 x 4 Over Sleeve Post - 3.5 Rail Privacy Shadowbox
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More information600G2 Internal Sliding Adapter Panel Shelf Instructions
Instruction Sheet 860391986 Issue 6, February 2013 SYSTIMAX Solutions 600G2 Internal Sliding Adapter Panel Shelf Instructions General The SYSTIMAX 600G2 adapter panel shelf is 19-inch wide x 1.75-inch
More informationCONNECTING BLOCKS 66-TYPE TOOLS, TERMINATING, ADAPTERS, AND MAINTENANCE. (5) Tighten screw.
BELL SYSTEM PRACTICES AT&TCo Standard SECTION 461-604-100 Issue 2, August 1971 CONNECTING BLOCKS 66-TYPE TOOLS, TERMINATING, ADAPTERS, AND MAINTENANCE 1. GENERAL 1.01 Reissued to add information on 183B2
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationSHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail
SHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set Posts
More informationPRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.
PRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set
More informationInstallation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
More informationN ETWOR KS FHX 8-PORT FIBER ENCLOSURE USER MANUAL
N ETWOR KS FHX 8-PORT FIBER ENCLOSURE USER MANUAL Contents Safety Information... I Chapter 1 Installation Instructions... 1 1.1 Package Contents... 1 1.2 Carton Contents... 2 1.3 Labeling... 2 1.4 Installing
More informationNOTE: The 1-piece panel is required for installation (the face mounts to the panel).
Installation Notes Flush Wood Plus Cypress Face Installation Before installing, make sure to install the one-piece panel, and disconnect the power cords making sure the Molex connector and two wires are
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationFS-526 Finisher INSTALLATION MANUAL
Applied Machines: C652/C552 COLOR MFP: 65 ppm/55 ppm Product Code: A0P0/A0P FS-526 Finisher INSTALLATION MANUAL Lifting the machine in an awkward position or transporting it in a poorly balanced position
More informationC-L-X ARMOR REMOVAL PROCEDURES
C-L-X ARMOR REMOVAL PROCEDURES USING THE KETT MODEL #KS-226 CABLE SAW The procedure listed below details Okonite s recommended method for removing C-L-X armor from large and small diameter cables. These
More informationMIL-STD B (SH) UPDATE
MIL-STD-2042-5B (SH) UPDATE Method 5A1 Insert Equipment and materials (to be added to table 5A1-I) Pliers 3.2.2.2 Cable and fiber preparation for Fiber Systems International backshells. Step 1: Ensure
More informationAurora,Ohio Fax:
VPI VIDEO 1275 Danner Drive PRODUCTS Tel: 330-562-2622 www.vpi.us INCORPORATED Aurora,Ohio 44202 Fax: 330-562-1999 CRIMP-RJ45-SF 8 Contact Modular Crimp Tool For RJ45 Superflat Modular Plugs Introduction
More informationWhat you should have. 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring. 3. Numbered bars or spokes(8) 4. Center plate (1)
20 ft RGB Pole Tree What you should have 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring 3. Numbered bars or spokes(8) 4. Center plate (1) 5. Top Ring (1) 6. Hardware and wrenchs a. Hardware i.
More information1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions 1. 2.
1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions Right Stack top panels on bottom panels Unfold display wall Set in desired configuration Wrong Pull from here Remove each folded
More informationBIG CEE. ENGINEERING 627 N Michigan Ave #5 Pasadena, CA
Garmin Emap power adapter housing BIG CEE ENGINEERING 627 N Michigan Ave #5 Pasadena, CA 91106 bigcee@bigcee.com www.bigcee.com This kit allows you to remove the circuit board from your Emap 12V adapter
More informationSetting Up the Polycom RealPresence Group Series Media Center
Setting Up the Polycom RealPresence Group Series Media Center Setting Up the Polycom RealPresence Group Series Media Center with a Single 55 or 65 Display or 55 Dual Displays Base Legs (4) M10 x 50 flanged
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationV00029KX READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID
READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID Net-Verse D-Type Cabinets Tool List 10mm Socket Wrench 122mm (48 ) Level 19mm Wrench 8mm Hex Drive T25 Torx driver Net-Verse D-Type
More informationFraming & Electrical Rough-in for Recess Mount IS Panel System
Framing & Electrical Rough-in for Recess Mount IS Panel System Overview Careful pre-planning and design lay-out are critical to successfully installing a Recess Mount IS (Infra- Sauna) Panel System. The
More informationChicago Electric MIG B Gun Install
Chicago Electric MIG 180 81295B Gun Install Step 1 First you will need to remove all the side panels on your machine. This is necessary to access everything for this install. Step 2 On the side with your
More informationGORE Aerospace Ethernet Cables
Termination Instructions The following procedures are based on Gore s best practices for terminating GORE Aerospace with the Carlisle Octax Connector System for both socket and plug versions. These procedures
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationTREX ENHANCE RAILING (Also Applies to Trex Select Railing) Installation Instructions
TREX ENHANCE RAILING (Also Applies to Trex Select Railing) NOTE: All Enhance Railing lengths are manufactured at CLEAR SPAN dimensions (spanning between space of posts): 7" for 6' clear span. Note that
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationDUZcart Cover Replacement Manual
DUZcart Cover Replacement Manual Page 1 of 23 DUZcart Replacement Instructions, January 2012. Call 1-888-389-2278 ext. 523 for additional assistance. The following describes the removal and replacement
More informationThe AstroGazer Instruction ManualV1.923
The AstroGazer Instruction ManualV1.923 Thank you for your purchase. If you have any questions, please call or email JGS Enterprises, LLC 540-898-0636 or info@astrogizmos.com 2/24/2008 1 Note: We are no
More informationPlug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions
www.lightorama.com Plug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions Read all instructions before you start Kit assembly! STEP 1. Check that all parts are included Parts
More informationFS-527 Finisher INSTALLATION MANUAL
FS-527 Finisher INSTALLATION MANUAL Index FS-527 (d-color MF360/MF280/MF220) I. Accessory parts... II. Confirmation before installation... 2 III. Installation procedures... 3 FS-527 (d-color MF45) I. Accessory
More informationSTOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets
Rev. 04 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS S-Type Network Cabinets -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More information3M No Polish SC/APC Angle Splice Connector Jacket for 2 x 3 mm FRP and 1.6 to 3.0 mm Cable 8802-T/APC/AS/1.6-3
3M No Polish SC/APC Angle Splice Connector Jacket for 2 x 3 mm FRP and 1.6 to 3.0 mm Cable 8802-T/APC/AS/1.6-3 Instructions October 2013 3 1.0 Table of contents 1.0 Summary...3 2.0 Cable and Fiber Preparation...4
More informationAeon AcousticPro UHD Series
Aeon AcousticPro UHD Series EDGE FREE Fixed Frame Sound Transparent Projection Screen User s Guide Product Description: The Aeon AcousticPro UHD Series is a fixed frame projection screen that uses Elite
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationSTOP! READ THIS FIRST
STOP! READ THIS FIRST Page 1 of 37 Getting Started With Your Pantograms GS1501 Embroidery Machine (the quick guide) Thank you for choosing Pantograms for your embroidery system provider. We encourage you
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationROMAN AND. Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION INSIDE MOUNT. A few simple tools are required:
ROMAN AND WOVEN WOOD SHADES Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper
More informationMTRTH and MTRTLS. MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS OPERATION INSTRUCTIONS
MTRTH and MTRTLS PA25279A01 Rev. 02 4-2009 MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS OPERATION INSTRUCTIONS Panduit Corp. 2009 INTRODUCTION The MTRTH Retained Tension Installation
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Traditional SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationPart Number RER.5E-X RER.75E-X RER1.25E-X RER2.0E-X. Height C
ELETRIL SOLUTIONS Harness oard ccessories Panduit harness board accessories provide fast routing and forming of wires in harness fabrication. They hold the wires off the harness board at a uniform height
More informationLange Crank Hoist-a-top Assembly Instructions
Lange Crank Hoist-a-top Assembly Instructions Installation Time: 1-4 Hours depending on skill level Tools Required: Cordless Drill Level Stud Finder Ratcheting wrench 9/16 socket or wrench 11/16 socket
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationVSD-6500 Frame Exploded View LIFT P/N
VSD-6500 Frame Exploded View LIFT P/N 511-65075-01 34 34 45 96 55 108 22 9 7 55 54 34 89 90 56 24 99 23 111 SEE SHEET 4 34 91 45 106 20 55 26 68 95 5 55 109 7 22 8 54 53 71 66 5 95 31 58 6 6 46 60 73 25
More informationr--- INSIDE WIRE CABLE
Scanned b Frank Harrell, (Cowbo Frank) Castle Rock, Colorado Oct 09, 01 14:6 :"ol. BELL SYSTEM PRACTICES Plant Series SECTION 461-60-1 00 Issue 1, January 1968 AT&TCo Standard CONNECTING BLOCKS 4A, 44A,
More informationSeeMeCNC Guides. Rostock Max v1/v2 HE280 Hotend Upgrade. This How-to Guide will walk you through the steps of upgrading to the HE280 Hotend.
SeeMeCNC Guides Rostock Max v1/v2 HE280 Hotend Upgrade This How-to Guide will walk you through the steps of upgrading to the HE280 Hotend. Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 33 Step
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and
More informationINSTALLATION INSTRUCTIONS
www.marwincompany.com Kit Number Door Height Rough Opening Height KD200BB68 80 84 ½ KD200BB70 84 88 ½ KD200BB80 96 100 ½ INSTALLATION INSTRUCTIONS 200BB SERIES KD POCKET DOOR FRAME FOR 2 X 4 STUD WALLS
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationcampfire big lamp Assembly Instructions
campfire big lamp Assembly Instructions tools needed Here's what's in the box BOX #3 For assembly videos go to myturnstone.com/campfire/instructions BOX #1 Base (1) assembly time needed video X screw (4)
More informationTradewinds Amplify Display System Instructions
Table of Contents Packing & Unpacking... Standard Kits... Component Identification... Primary Components Vertical Pole Top... Vertical Pole Bottom... Horizontal... Cross/Hanging Bar... Amplify Shelf Package
More informationTREX SELECT RAILING. Installation Instructions PARTS
RAILING NOTE : All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (76.8 cm) for 6' (.83 m) on center, and 9-5/8" (35.3 cm) for 8' (.44
More informationTrackstar Manual Folding Shade Installation Instructions
Trackstar Manual Folding Shade Installation Instructions Tracklock or Cord and Pulley Lifting System Thank you for purchasing your new Trackstar folding shade. It has been custom-made from the highest
More informationDART MAXI DAL- cod. 2DL7CS00. To ensure a maximum efficient use of the product, read the instructions before proceeding installment.
Targetti USA - A Targetti Group Company - 750-A W 7th St. Costa Mesa, CA 967 - Phone (74) 53-99 - Email:targettiusa@targetti.com - www.targetti.us - 05..7 - Page of 0 DART MAXI DAL- cod. DL7CS00 9." 8.43"
More informationVIT SB-16SS Pedestal. Conversion Guide
Converting a to Baseline This guide describes the steps for removing another manufacturer s irrigation controller from a VIT SB-16SS pedestal and installing a Baseline controller. Remove All Parts of the
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Toyota RAV4 1996-2000 THE safety accessory of the 21 st Century. P/N 210-0034-0 Rev B1 (11-19-02), GG 2002 Muth Co. LLC. Note: Professional Installation Recommended
More informationPanduit 28 AWG Patch Cords Installation Guideline
Panduit 28 AWG Installation Guideline Panduit is a leading supplier of Structured Cabling Systems and Unified Physical Infrastructure. Panduit solutions enable the physical infrastructure to be scalable,
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationMedia Storage Systems Fixed Media Cabinets
Owner s Manual Media Storage Systems Fixed Media Cabinets Contents 1-Column Fixed Media Storage Cabinet Important User Information...........................2 Safety Precautions.................................3
More informationCM543 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID
CM543 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-SERV Co-Location Cabinet (S752S2C122B) Panduit Corp. 2011 INSTRUCTIONS CM543 FRONT OF CABINET REAR OF CABINET NOTE:
More informationTH Place, Maspeth, NY Instruction Manual for UNO Exit Signs
57-10 49 TH Place, Maspeth, NY 11378 Instruction Manual for UNO Exit Signs 1. What is included in this box? Back box with electronics, battery (where applicable), & mounting hardware. Inner trim, LED illuminator
More informationSDS TAP Retrofit Install Bartlett 3 Key Installation of TAP Control for Models Originally Built with the Bartlett 3 Key Control
SDS TAP Retrofit Install Bartlett 3 Key Installation of TAP Control for Models Originally Built with the Bartlett 3 Key Control This SDS Industries TAP Retrofit kit and installation instructions are intended
More information