Metal Garden Skylight Shed

Transcription

1 A L L P U R P O S E M E T A L S T O R A G E S H E D S Pent Roof Type Metal Garden Skylight Shed OWNER S MANUAL / Instructions for Assembly Size 8 Ft. x 6 Ft. Customer Service Hotline (800) Tall Walk in Shed Quick & Easy Assembly Ridge Reinforced Walls Wide Double Doors Available in Various Sizes Call us for any missing or damaged parts. Do not return to the store.

2 Duramax Storage Shed Limited Fifteen Year Warranty U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or workmanship for a period of fifteen years from the date of purchase. This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring, labor, installation or any other costs related thereto. This warranty only covers failures due to defects in material or workmanship which occurs during normal use and does not extend to color change arising due to normal weathering or to damage resulting from misuse or neglect, commercial use, failure to follow assembly instructions and the owner s manual (including proper anchoring of the shed), painting, forces of nature and other causes which is beyond our control. Claims under this warranty must be made within the warranty period by calling or mail in a dated sales slip and clear photograph of the part to: U.S. Polymers, Inc. 057 S. Vail Ave, Montebello,CA We reserve the right to discontinue or change components. If a component has been discontinued or is not available, U.S. Polymers, Inc. reserves the right to substitute a component of equal quality as may be compatible. Limits and Exclusions There are no express warranties except as listed above. The warrantor shall not be liable for incidental or consequential damages resulting from the use of this product, or arising out of any breach of this warranty. All express warranties are limited to the warranty period set forth above. Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country.

3 Parts List : Check all parts prior to installation. ACCESSORIES PROFILES CODE QTY. ACCESSORIES BLB BRB ECB DCLP DCRP SCB SSB SLB RSLP RSRP RSMP SBMP SBSP RFSP RFRB RFLB 6 GPSLP GPSRP FBLP RPSLP 3 DPLP DPRP CODE QTY. BS 4 DH TC 4 TS 4 Slab PC 3Slab 70 S 6 90 Floor Kit: CODE QTY EFB0 EFB0 EFB03 4 EFB04 5 BS TC,S - Use screws with plastic washers on top of prepainted surface only. DH TS PC BLB, BRB, DCLP SCB SLB, RSLRB,RSM ASLR ECB DCRP SSB SBMP,SBSP RFSP,RFLB, RFRB EFB0,EFB0, EFB03,EFB04 Tools You Will Need Hand Gloves Cordless Drill - Philips Head Screw driver - Philips Head Carpenters Square Eye Protector 8 Step Ladder Adjustable pliers Level - 3ft. Tape Measure

4 Exploded View RFSP RPSLP RFRB RFLB RFLB GPSLP SBSP RSLP RFRB RPSLP RFSP SBMP FBLP RSMP SBSP RSRP GPSRP SLB SSB EFB03 BLB DPLP SCB DCLP EFB0 ECB EFB0 EFB04 BRB EFB03 DPRP DCRP

5 A. Base Frame It is important that these instructions are followed step by step. Don t install under windy conditions. Parts needed: CODE QTY BLB BRB BSC ECB S Take care of sharp edges. Use screws with plastic washers on top of prepainted surface only. BLB BLB & BRB BRB BLB BLB BRB BRB

6 3 S 4 S ECB ECB & 5 EFB0 EFB0 EFB0 EFB0

7 6 BLB EFB0 EFB03 EFB03 EFB03 EFB03 BRB EFB0 7 EFB03 EFB04 EFB04 EFB03 3

8 B. Walls & Columns All panels are clearly marked and care should be taken to use the correct one. IMPORTANT: Use screws with plastic washers on top of prepainted surface only. S Parts needed: CODE QTY SLB ASLR SSB CODE QTY SCB TS 4 DCLP DCRP Make sure the overlapping position is as shown in fig. 4

9 3 4 & 5 Make sure the position of the projection on (TS) towards inside. TS 5

10 6 Left 7 Make sure the overlapping position is as shown in fig. Left 8 6 Left

11 9 SLB SLB & Left 0 Make sure the position of the projection on top slider towards inside. SLB TS SLB Left SLB & SLB SSB SSB SLB SSB Left 7

12 Left 3 Make sure the overlapping position is as shown in fig.. BLB BLB Fig.3 3 Left 4 & Left 8

13 5 Make sure the overlapping position. See fig.. Left 6 Top angle () must sit on top angle (). & Left 7 9

14 8 Make sure the overlapping position of panels is as shown in fig.. BRB BRB 3 Fig.3 9 & 0 Make sure the overlapping position. See fig.. 0

15 Top angle () must sit on top angle () & 3 Make sure the overlapping position. See fig.. 3 Fig.3

16 4 Make sure the overlapping position. See fig.. 5 DCLP DCLP DCLP 6 DCLP DCRP DCLP

17 7 SCB SCB 3

18 C. Roof All parts are clearly marked and care should be taken to use the correct one. Remove the polyethylene film before assembling. IMPORTANT: Use screws with plastic washers on top of prepainted surface only. S Parts needed: CODE QTY. FBLP GPSLP GPSRP RSRP RSLP RSM SBMP SBSP RPSLP 3 CODE QTY. RFSP RFLB RFRB TC S 4 48 FBLP S S S 3 Inside 4 Fig.3

19 3 S S FBLP FBLP FBLP 3 SLB FBLP S SLB SLB Inside SLB Fig.3 4 GPSLP FBLP 5 GPSRP 5

20 6 Make sure the taper side (RSLP & RSRP) must be up. Taper side S SBMP RSRP RSRP SBSP RSLP RSLP RSLP SBMP SBSP SBSP 7 RSRP RSRP GPSRP RSRP GPSRP RSLP 8 FBLP FBLP RSMP RSRP RSMP S RSMP RSLP 6 RSRP

21 9 RPSLP RPSLP GPSRP RSRP GPSRP 0 Make sure the overlapping position is as shown in the blow up. RSRP RPSLP RPSLP Make sure the overlapping position is as shown in the blow up. RPSLP FBLP RSLP 7

22 Make sure the overlapping position is as shown in the blow up. FBLP RSLP RPSLP 3 Make sure the overlapping position is as shown in the blow up. RPSLP Left RPSLP 4 RFSP RFSP 8

23 5 RFRB RFLB RFLB RFRB 6 S TC 9

24 D. Door DPLP DPRP TS 3 BS TS Fig.3 TIP To get proper alignment of the door realign the holes with door panel. See fig. TS Door Panel ECB TS Door Panel BS Fig.4 Fig.5 0

25