A Cost Effective Solution for Long Lasting Durability.

Transcription

1 March 202 Wilson Standard Thick Turret Tooling System A Cost Effective Solution for Long Lasting Durability. Strength. Performance. Innovation.

2 REDUCE COSTS AND INCREASE TOOL LIFE WITH WILSON STANDARD. Ultra durable and loaded with performance enhancing features, Wilson Standard Thick Turret Tooling is an affordable solution for fabricators looking to improve productivity and reduce tool replacement costs. Stronger tool steels, an intelligent design and optional surface enhancements combine to make Wilson Standard the new standard in low cost, high quality thick turret tooling. Longer Life and Greater Precision. Wilson Standard Thick Turret Tooling is manufactured with a hardened steel guide, providing four times more grind life than traditional old style guide assemblies. A built-in oiling system assures proper internal/external lubrication for a consistently smooth and precise punching action. Quick, Accurate Adjustments. Wilson Standard Thick Turret Tooling is uniquely designed to speed adjustments. External keying allows for quick key position changes and push button punch length adjustments eliminate the need for shims. Two-inch (C) and 3-/2 inch (D) station guide assemblies are keyed at 0, 90 and 225 and keys are coated with Wilson s exclusive Optima coating for superior wear resistance.

3 Improve Wear Resistance with Optima. Every Wilson Standard Thick Turret Tooling is available with Wilson s exclusive Optima coating. Developed by Wilson engineers, Optima provides a surface hardness, wear resistance and lubricity unmatched by any other coated or uncoated turret punch press tooling. The result is a longer tool life, more hits between sharpenings, reduced galling, better performance and less downtime. Optima coating provides: Longer tool life Increased wear resistance More hits between sharpenings Reduced adhesion (galling) Reduced slug pulling Punch Life The yellow area indicates actual results achieved through three tool sharpenings of.00" (0.25mm) each. The complete graph indicates projected results with a total of.236" (6mm) removed for sharpening. Number of Hits Reduced corner breakdown Improved special tooling performance Lower overall tooling costs Material Adhesion Tip Wear TABLE OF CONTENTS EXP (A & B) Tooling /2" (A) Station Tooling /4" (B) Station Tooling..-4 2" (C) Station Tooling /2" (D) Station Tooling /2" (E) Station Tooling... 7 Replaceable Insert Assembly.. 8 Close to Clamps Tooling...9 Shear Options...20 HP Dura-Blade...2 Dura-Die...22 Standard Keying Locations...23 Non-Standard Keying...24 Multi-Tools For Finn-Power Machines...25 Multi-Tools For Nisshinbo Machines...26 Accessories Tools Tooling Cabinet...29 Shear Grinding Fixture & Accessories...29 Multi-Tool Punch and Die Holders...29 Tool Kit...30 Slug Ejectors...30 Center Punch...30 Alignment Tools...3 Adapters...32 Ball Riding Die...33 Brush Die...33 Punch & Die Shims...34 Notcher Plate...35 Wilson Punch & Die Grinder.. 36

4 3 EXP /2" (A) Station HP ROUND punch holder HP ABS/WLS ROUND punch holder round PUNCH 3904 standard SHAPE punch holder Description PunchES METRIC SHAPE punch holder Description Punch HOLDER HP Round HP Shape HP ABS/WLS Round HP ABS/WLS Shape Standard Round Standard Shape Metric Round Metric Shape Metric ABS/WLS Round Metric ABS/WLS Shape Ultra METRIC ABS/WLS SHAPE punch holder ULTRA punch holder

5 EXP -/4" (B) Station 4 HP shape punch holder HP ABS/WLS shape punch holder punch shape 397 standard SHAPE punch holder Description PunchES METRIC SHAPE punch holder Description METRIC ABS/WLS SHAPE punch holder ULTRA punch holder Punch HOLDER HP Round HP Shape HP ABS/WLS Round HP ABS/WLS Shape Standard Round Standard Shape Metric Round Metric Shape Metric ABS/WLS Round Metric ABS/WLS Shape Ultra

6 5 ELIMINATE COSTLY SLUG PULLING. The Slug Pulling Solution For a guaranteed solution to slug pulling problems that will maximize your press time and improve your productivity turn to Wilson Tool, the leading provider of tooling solutions for the punching industry. Manufacturers simply cannot afford to have their presses down for any amount of time. At Wilson Tool, our desire to provide innovative tooling solutions for our customers has lead us to develop the Slug Hugger 2 die design to help eliminate the very costly problem of slug pulling. The Slug Hugger 2 design works on most material types and thicknesses including aluminum and stainless steel. Slug Hugger 2 dies help eliminate scrapped parts, costly downtime, and possible press and tooling damage due to slug pulling. At Wilson Tool, our Slug Hugger 2 dies include a performance guarantee. Our unique design helps eliminate unnecessary back-pressure on small punch tips by preventing packed slugs. How Does it Work? The Slug Hugger 2 design grabs the slug just below the cutting surface of the die and retains the slug during the stripping process. Precision Nips extend the entire height of the die, helping to guide the slugs through the relief. This design doesn t leave any marks or burrs on the finished part. The Slug Hugger 2 nips hold the slugs in the die and drags it through the relief when the next hit takes place. This feature allows for less galling and slug packing when punching materials such as aluminum and galvanized steel. In addition, the effectiveness of the Slug Hugger 2 will not be compromised when the tool is sharpened. Our Guarantee! Try the Slug Hugger 2 dies to control your slug pulling. We guarantee that your slug pulling problems will be eliminated! Strength. Performance. Innovation.

7 Perforator /2" (A) Station 6 Adj. punch head with screw 802 Not recommended for stainless steel. (Up to 2.7mm) SOCKET HEAD SET SCREW CONE PT. (M6- x 6mm) (To be used with black oxide adj. punch head) 6297 spring 803 punch Shank 885 Spring Retainer with o-ring 804 O-ring 2282 Retaining Ring (2 req'd) 805 Guide 886 Lower Shank 887 Sleeve Assembly Dia. ( mm) 2029 Maximum Material Thickness.50" (3.8mm) Sleeve Assembly Dia. ( mm) 2030 Description price Punch & Guide Assembly w/slip Fit Sleeve Dia. ( mm) Dia. ( mm) Dia. ( mm) Dia. ( mm) Positive.037 (0.94mm) Min. Dia..062 (.57mm) Min. Dia

8 7 Metric /2" (A) Station Quik Adjust O-RING Quick Adjust Spring Pack Assembly 3394 O-ring dowel pin (replacement-round Only) (3/6 x.500) 23 (Up to 2.7mm) Punch head 3395 SOCKET HEAD SET SCREW (M6 x 6mm) Punch head Retainer 3396 M4x6 Half dog point screw spring 2429 spring Canister 3397 Retaining ring spring Support 3398 dowel pin (3/6 x.32) 603 Description price Punch & Guide Assembly Fitted Maximum Material Thickness.50" (3.8mm) Notes * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). 'A' Dimension = longest distance across shape. /2" (A) Station Add Ons Add ons for Rounds Small Diameter ( mm) ( mm) Add ons for Shapes Small Widths ( mm) ( mm) Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Slug Hugger * Standard Slug Hugger 2* Slug Hugger 2* at 45 Positive Negative

9 /2" (A) Station 8 (Up to 2.7mm) Adj. punch head with screw 802 SOCKET HEAD SET SCREW CONE PT. (M6- x 6mm) (To be used with black oxide adj. punch head) 6297 spring 803 O-ring 2282 Spring Retainer with o-ring 804 Retaining Ring 805 Dowel Pin (replacement-round Only) (3/6 x.595) 605 Guide Round/Closed Round 282 Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Slug Hugger * Standard Slug Hugger 2* Slug Hugger 2* at 45 Positive Negative Maximum Material Thickness.50" (3.8mm) /2" (A) Station Add Ons Add ons for Rounds Small Diameter Punch Die ( mm) ( mm) Small Widths ( mm) ( mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Guide SHape/Fitted 2904 Dowel Pin (3/6 x 0.32) 603 Stubby Style /2" (A) Station Round add Shape add Note: Must use stubby style die and guide with stubby style punch Use Standard Punch and Die Plus: Punch Round (.090/2.3mm max.dia.) add Shape add Die Standard Shapes SD Single-D LD Long-D ET Equilateral Triangle SQ Square HX Hexagon PUNCHES DD Double-D QD Quad-D OB Obround RT Rectangle OT Octagon DIES Radius or 45 Chamfer 4 Corners Radius or Chamfer Size ( mm) ( mm) Greater than.250 (6.35mm) Any size Total Add On

10 9 Heavy Duty /2" (A) Station (Up to 2.7mm) Adj. punch head with screw 2294 SOCKET HEAD SET SCREW CONE PT. (M6- x 6mm) (To be used with black oxide adj. punch head) 6297 spacer 2296 Disc spring (22 Req d) 2297 spring Support with O-ring 2295 O-ring 2282 Retaining Ring 805 Dowel Pin (replacement-round Only) (3/6 x.595) 605 Stubby Style /2" (A) Station Note: Must use stubby style die and guide with stubby style punch Use Standard Punch and Die Plus: Punch Round (.090/2.3mm max.dia.) add Shape add Round add Shape add Guide Round/Closed Round 282 Die Guide SHape/Fitted 2904 Dowel Pin (3/6 x 0.32) 603 /2" (A) Station Add Ons Add ons for Rounds Small Diameter Punch Die ( mm) ( mm) Small Widths ( mm) ( mm) Maximum Material Thickness.250" (6.35mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Slug Hugger * Standard Slug Hugger 2* Slug Hugger 2* at 45 Positive Negative Notes: * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). Std. keying for square guides is 0 & 45. 'A' Dimension = longest distance across shape.

11 /2" (A) Station Quik Adjust 0 (Up to 2.7mm) Punch head 3405 O-RING SOCKET HEAD SET SCREW (M6 x 6mm) 6297 Punch head Retainer 3396 M4x6 Half dog point screw Quick Adjust Spring Pack Assembly 3404 spring spring Canister 3406 Retaining ring spring Support 3407 dowel pin (replacement-round Only) (3/6 x.595) 605 O-Ring 2282 Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Slug Hugger * Standard Slug Hugger 2* Slug Hugger 2* at 45 Positive Negative Maximum Material Thickness.50" (3.8mm) /2" (A) Station Add Ons Add ons for Rounds Small Diameter ( mm) ( mm) Punch Die Add ons for Shapes Small Widths ( mm) ( mm) Punch Die Available April 2005 Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. dowel pin (3/6 x.32) 603 Stubby Style /2" (A) Station Note: Must use stubby style die and guide with stubby style punch Use Standard Punch and Die Plus: Punch Round (.090/2.3mm max.dia.) add Shape add Die Round add Shape add Standard Shapes SD Single-D LD Long-D ET Equilateral Triangle SQ Square HX Hexagon PUNCHES DD Double-D QD Quad-D OB Obround RT Rectangle OT Octagon DIES Radius or 45 Chamfer 4 Corners Radius or Chamfer Size ( mm) ( mm) Greater than.250 (6.35mm) Any size Total Add On

12 Metric -/4" (B) Station Quik Adjust ( mm) Punch head 3400 Quick Adjust Spring Pack Assembly 3399 dowel pin (replacement-round Only) (3/6 x.500) 23 SOCKET HEAD SET SCREW (M6 x 6mm) Punch head Retainer 340 O-ring spring 30 spring Canister 3402 Retaining ring spring Support 3403 o-ring dowel pin (3/6 x.345) 643 Notes * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). Std. keying for square guides is 0 & 45. 'A' Dimension = longest distance across shape. Maximum Material Thickness.250" (6.35mm) -/4" (B) Station Add Ons Add ons for Rounds Small Diameter Punch ( mm) ( mm) ( mm) Add ons for Shapes Small Widths ( mm) ( mm) 'A' Dimension <.437 (.0mm) Punch Die Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Slug Hugger * Standard Slug Hugger 2* Positive Negative (0 & 45 ) Slug Hugger 2* (0 & 45 ) Pos. (0 & 45 )Neg

13 -/4" (B) Station 2 ( mm) Adj. punch head with screw 82 SOCKET HEAD SET SCREW CONE PT. (M6- x 0mm) (To be used with black oxide adj. punch head) 6206 spring 953 Spring Retainer with o-ring 824 O-ring 2283 Dowel Pin (replacement-round Only) (3/6 x.500) 23 Description price Punch & Guide Assembly Fitted Dowel Pin (3/6 x.345) Maximum Material Thickness.250" (6.35mm) guides (0 ) (0 & 45 ) (0 & 90 ) Fitted /4" (B) Station Add Ons Add ons for Rounds Small Diameter Punch Die ( mm) ( mm) ( mm) Notes Slug Hugger * Standard Slug Hugger 2* Positive Negative (0 & 45 ) Slug Hugger 2* (0 & 45 ) Pos. (0 & 45 ) Neg Small Widths ( mm) ( mm) 'A' Dimension <.437 (.0mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). Std. keying for square guides is 0 & 45. 'A' Dimension = longest distance across shape. Standard Shapes SD Single-D LD Long-D ET Equilateral Triangle SQ Square HX Hexagon PUNCHES DD Double-D QD Quad-D OB Obround RT Rectangle OT Octagon DIES Radius or 45 Chamfer 4 Corners Radius or Chamfer Size ( mm) ( mm) Greater than.250 (6.35mm) Any size Total Add On

14 3 Heavy Duty -/4" (B) Station ( mm) Adj. punch head with screw 82 SOCKET HEAD SET SCREW CONE PT. (M6- x 0mm) (To be used with black oxide adj. punch head) 6206 spacer 230 Disc spring (20 Req'd) 2302 O-ring 2283 Spring support with o-ring 2300 Dowel Pin (replacement-round Only) (3/6 x.500) 23 Notes Dowel Pin (3/6 x.345) 643 Maximum Material Thickness.32" (7.93mm) -/4" (B) Station Add Ons Add ons for Rounds Small Diameter Punch Die ( mm) ( mm) ( mm) Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). Std. keying for square guides is 0 & 45. 'A' Dimension = longest distance across shape. Small Widths ( mm) ( mm) 'A' Dimension <.437 (.0mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Slug Hugger * Standard Slug Hugger 2* Positive Negative (0 & 45 ) Slug Hugger 2* (0 & 45 ) Pos. (0 & 45 ) Neg

15 -/4" (B) Station Quik Adjust 4 ( mm) punch head 3409 SOCKET HEAD SET SCREW (M6- x 0mm) 6297 Punch Head Retainer 340 Quik Adjust Spring Pack Assembly 3408 O-ring spring Spring Canister 3402 Retaining Ring Spring Support 340 Dowel Pin (replacement-round Only) (3/6 x.500) 23 O-ring 2283 Description price Punch & Guide Assembly Fitted guides (0 ) (0 & 45 ) (0 & 90 ) Fitted Maximum Material Thickness.250" (6.35mm) -/4" (B) Station Add Ons Add ons for Rounds Small Diameter Punch Die ( mm) ( mm) ( mm) dowel pin (3/6 x.345) 643 Notes Slug Hugger * Standard Slug Hugger 2* Positive Negative (0 & 45 ) Slug Hugger 2* (0 & 45 ) Pos. (0 & 45 ) Neg Small Widths ( mm) ( mm) 'A' Dimension <.437 (.0mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). Std. keying for square guides is 0 & 45. 'A' Dimension = longest distance across shape. Standard Shapes SD Single-D LD Long-D ET Equilateral Triangle SQ Square HX Hexagon PUNCHES DD Double-D QD Quad-D OB Obround RT Rectangle OT Octagon DIES Radius or 45 Chamfer 4 Corners Radius or Chamfer Size ( mm) ( mm) Greater than.250 (6.35mm) Any size Total Add On

16 5 2" (C) Station Standard & WLs For old style O-ring ADjustMENT PUSH BUTTON 0539 ADjustMENT LOCKING BALL ADjustMENT SHAFT 5735 Wave SPRING PUNCH HOLDER 5556 DISC SPRING (2 Req d) anti-lock shim 542 URETHANE (2 Req d)(3/32 Sq. x 27/64) (Pkg of 50) 66 SOCKET HEAD CAP SCREW (M2 x 40mm) 6605 SOCKET HEAD CAP SCREW (/2-3 x.5 ) 6606 guide 5420 socket head cap screw 429 ( mm) retaining RING SPRING DISC SPRING (2 Req d) 5744 driver assembly 5729 DRIVER 5736 SPRING Cover 5693 SPRING SUPPORT 5748 SOCKET HEAD CAP SCREW (2 Req d) (Spl. M5 x.8 Cone Pt.) 597 LOCKWasher (2 Req d) 22 RETAINING RING SOCKET HEAD CAP SCREW (M3 x 2mm) 6326 LOCKWasher 6327 punch holder Key 5373 GUIDE STRIPPER RING 5035 Description price Maximum Material Thickness.250" (6.35mm) Guide Assembly Gravity Feed WLS Ready Notes Assemblies also available with quick-release stripper retention system (HP ) #5555 (/2-3) or #5577 (m-2) Guide Assys. are keyed for shapes at 0, 90, and 225. All punches will be shipped with no shear unless specified. * Slug Hugger dies must be ordered punch size plus clearance,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). 'A' Dimension = longest distance across shape. 2" (C) Station Add Ons Add ons for Rounds Small Diameter Punch Die <.000 (25.4mm) Small Width ( mm) ( mm) Small 'A' Dimension <.50 (29.2mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. * These assemblies accept either /2-3 or M-2 style punches /2"-3 Thread M-2 Thread /2"-3 Thread M-2 Thread strippers /Fitted Slug Hugger * Standard Slug Hugger 2* Positive Negative

17 3-/2" (D) Station Standard & WLs For old style 6 O-ring ADjustMENT PUSH BUTTON 5737 ADjustMENT LOCKING BALL ADjustMENT SHAFT 5739 Wave SPRING SPRING COVER 5423 PUNCH HOLDER 5558 anti-lock shim 543 DISC SPRING (2 Req d) URETHANE (3/32 Sq. x 27/64) (Pkg of 50) 66 SOCKET HEAD CAP SCREW (/2-3 x 2) 6325 SOCKET HEAD CAP SCREW (M2 x 50mm) guide with hardware 5430 socket head cap screw 429 ( mm) retaining RING SPRING DISC SPRING (7 Req d) 5449 driver assembly 5730 DRIVER 5740 RETAINING RING 5747 SOCKET HEAD CAP SCREW (2 Req d) (Spl. M5 x.8 Cone Pt.) 597 LOCKWasher (2 Req d) 22 SPRING SUPPORT 5738 punch holder Key 862 LOCKWasher (2 Req d) 22 SOCKET HEAD CAP SCREW (2 Req d) (M5 x 2mm) 60 GUIDE STRIPPER RING 5036 Description price Guide Assembly Gravity Feed WLS Ready * These assemblies accept either /2-3 or M-2 style punches /2"-3 Thread M-2 Thread /2"-3 Thread M-2 Thread strippers Slug Hugger * Standard Slug Hugger 2* Positive Negative Maximum Material Thickness.250" (6.35mm) 3-/2" (D) Station Add Ons Add ons for Rounds Small Diameter Punch Die <.900 (48.26mm) Small Width ( mm) ( mm) Small 'A' Dimension <.900 (48.26mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Notes Assemblies also available with quick-release stripper retention system (HP ) #5557 (/2-3) or #5578 (m-2) Note: Guide Assys. are keyed for shapes at 0, 90, and 225. /6" (.6mm) Rooftop shear is given to all punches with 'A' dimension greater than (50.8mm), and width greater than.250 (6.35mm), at no extra charge. All punches.250 (6.35mm) and under in width will be shipped with no shear unless specified. * Slug Hugger dies must be ordered punch size plus clearance,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). 'A' Dimension = longest distance across shape. Standard Shapes SD Single-D LD Long-D ET Equilateral Triangle SQ Square HX Hexagon PUNCHES DD Double-D QD Quad-D OB Obround RT Rectangle OT Octagon DIES Radius or 45 Chamfer 4 Corners Radius or Chamfer Size ( mm) ( mm) Greater than.250 (6.35mm) Any size Total Add On

18 7 4-/2" (E) Station Standard & WLs For old style O-ring ADjustMENT PUSH BUTTON 5737 ADjustMENT LOCKING BALL ADjustMENT SHAFT 5739 Wave SPRING PUNCH HOLDER 5560 LIFTER PIN (4 Req d) 5209 SOCKET HEAD CAP SCREW (4 Req d) (Spl M5 x 3.39mm Cone Pt.) 520 anti-lock shim 543 URETHANE (3/32 Sq. x 27/64) (Pkg of 50) 66 DISC SPRING (2 Req d) SOCKET HEAD CAP SCREW (/2-B x 2.000) 6325 SOCKET HEAD CAP SCREW (M2 x 50mm) ( mm) retaining RING SPRING DISC SPRING (7 Req d) 5449 driver assembly 573 DRIVER 5742 SPRING COVER 5423 SPRING SUPPORT 574 RETAINING RING 5747 punch holder Key LOCKWasher (2 Req d) 22 SOCKET HEAD CAP SCREW (2 Req d) (M5 x 2mm) 60 guide WITH HARDWARE 5438 socket head cap screw 429 GUIDE STRIPPER RING 5037 Maximum Material Thickness.250" (6.35mm) Description price Notes Assemblies also available with quick-release stripper retention system (HP ) #5559 (/2-3) or #5579 (m-2) Note: Guide Assys. are keyed for shapes at 0, 90. /6" (.6mm) Rooftop shear is given to all punches with 'A' dimension greater than (50.8mm), and width greater than.250 (6.35mm), at no extra charge. All punches.250 (6.35mm) and under in width will be shipped with no shear unless specified. * Slug Hugger dies must be ordered punch size plus clearance,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). 'A' Dimension = longest distance across shape. 4-/2" (E) Station Add Ons Add ons for Rounds Small Diameter Punch Die < (86.36mm) Small Width ( mm) ( mm) Small 'A' Dimension < (86.36mm) Add ons for Shapes Punch Die Additional charges apply to round or shape punch for extra straight before radius, extra back taper, or no back taper. Guide Assembly Gravity Feed WLS Ready * These assemblies accept either /2-3 or M-2 style punches /2"-3 Thread M-2 Thread /2"-3 Thread M-2 Thread strippers Slug Hugger * Standard Slug Hugger 2* Positive Negative

19 Replaceable Insert Assembly For Old style 8 Replaceable Insert Assembly Station 2" (C) 3-/2" (D) 4-/2" (E) Body (/2" - 3) Body (M - 2) Punch Insert Set (/2" - 3) Set (M - 2) Parts Description Socket Head Cap Screw 3/8" - 6 x -/2" long [2" (C) station] Socket Head Cap Screw 3/8" - 6 x " long [for 3-/2" (D), 4-/2" (E) & 6" (F) stations] High Collar Lock Washer for 3/8" screw Dowel Pin /4" Dia. x.450" long (All Stations) Notes Optima is standard on punch inserts. Blade insert punches under.375" (9.53mm) in width will be shipped with no shear unless specified. Double Valley Shear is recommended for widths of.87" (4.75mm) thru.375" (9.53mm) and minimum lengths of 2.000" (50.8mm) when used for nibbling. Undersized dimensions will incur additional charges. Please consult the fee schedule for the appropriate station to determine the charge. See Shear chart page 8. For widths less than.093" (2.36mm), consult the sales desk. Maximum width.750" (9mm). Inserts are available as obround to be used with rectangle dies, to eliminate Saw Tooth Effect.

20 9 Close to Clamps Tooling 3-/2" (D) Station For Punching Close to Clamps Description Thin Clamps Thick Clamps Optima /2" (E) Station For Punching Close to Clamps Description Thin Clamps Thick Clamps Optima Plates Thin Clamps Thick Clamps Plates Thin Clamps Thick Clamps Slug Hugger 2* (relief 2 sides, shp at 90 ) Slug Hugger 2* (relief 2 sides, shp at 0-90 ) Slug Hugger 2* (relief side, shp at 90 ) Slug Hugger 2* (relief side, shp at 0-90 ) Slug Hugger 2* (relief 2 sides, shp at 90 ) Slug Hugger 2* (relief 2 sides, shp at 0-90 ) Slug Hugger 2* (relief side, shp at 90 ) Slug Hugger 2* (relief side, shp at 0-90 ) Notes All punches will be shipped with no shear unless specified. * Slug Hugger dies must be ordered punch size plus clearance,.060 (.53mm) min. width on shapes,.006 (0.5mm) min. total clearance (patented). 'A' Dimension = Longest distance across shape. Positive (relief 2 sides, shp at 90 ) Positive (relief 2 sides, shp at 0-90 ) Positive (relief side, shp at 90 ) Positive (relief side, shp at 0-90 ) Negative (relief 2 sides, shp at 90 ) Negative (relief 2 sides, shp at 0-90 ) Negative (relief side, shp at 90 ) Negative (relief side, shp at 0-90 ) Positive (relief 2 sides, shp at 90 ) Positive (relief 2 sides, shp at 0-90 ) Positive (relief side, shp at 90 ) Positive (relief side, shp at 0-90 ) Negative (relief 2 sides, shp at 90 ) Negative (relief 2 sides, shp at 0-90 ) Negative (relief side, shp at 90 ) Negative (relief side, shp at 0-90 )

21 Shear Options 20 Type of Shear Benefit Limitation Rooftop Best shear for punching at maximum tonnages. When nibbling, bite must be 75% of punch dimension or excessive side loading will result. Concave or Double Concave Inverted Rooftop Double Valley Shear JK Shear Best shear for nibbling because it inverts stresses. Also good shear for nibbling because it inverts stresses. Best shear for nibbling when shape is long and narrow. A special punch tip shear that allows you to punch high strength materials with a reduced risk of breakage. The punch is less resistant to breakage when punching at high tonnages because of inverted stresses. More susceptible to breakage because of a sharp focal point for stresses use great care. The punch is less resistant to breakage when punching at high tonnages because of inverted stresses. Can only be used on punches up to.000" (25.4mm) diameter or 'A' dimension. Station -/4" (B) 2" (C) 3-/2" (D) 4-/2" (E) 'A' Dimensions Within.250" (3.75mm) Within 2.000" (50.8mm) Within 3.500" (88.9mm) Within 4.500" (4.3mm) Special Shears Inverted Rooftop Single Concave Double Valley Double Concave /6" (.6mm) Shear /8" (3.2mm) Shear /6" (.6mm) Shear /8" (3.2mm) Shear /6" (.6mm) rooftop shear is given to all punches with 'A' dimension greater than 2.000" (50.8mm) and width greater than.250" (6.35mm) at no extra charge. All punches.250" (6.35mm) and under in width will be shipped with no shear unless specified. 'A' Dimension = Longest distance across shape. NOTE: In some instances, inverted rooftop is substituted for single and double concave shears. JK Shear Shape Round Rectangle, Square, Hexagon Single D, Double D Obround Notes Add On If specified: /8" (3.2mm) maximum rooftop shear can be given at N/C for any round or shape in 2"(C), 3-/2"(D), 4-/2"(E) or 6"(F) stations. Additional charges apply for rooftop shear on any round or shape in /2"(A) or -/4"(B) stations. DIE CLEARANCE SELECTION INFORMATION Material Copper, /2 Hard Brass, /2 Hard Mild Steel Steel 0.50C Aluminum, Soft Stainless Steel % Total Clearance Minimum Best % x Material Thickness=Total Clearance Maximum

22 INCREASE YOUR PRODUCTION WITH HP DURA-BLADE Reach new levels of sheet metal parting productivity with Wilson Tool s High Performance Dura-Blade parting tool for thick and thin turret punch presses. Wilson Tool s highly engineered HP Dura-Blade dramatically reduces downtime by maximizing the number of hits between sharpenings. Dura-Blade utilizes a replaceable, fully-guided blade insert made of Ultima Premium tool steel. It also features quick release stripper plate retention and a push button adjustment system that allows for fast and easy tool changes. Only HP Dura-Blade is uniquely equipped to handle the daily rigors of sheet metal parting, so you can finish the job right. High Performance Features HP Dura-Blade includes all the performance-driven features of the HP-style tooling: HP-style quick release stripper retention for fast and easy tool changes HP-style side-mounted push-button for fast and easy tool adjustments Plus Cutting insert made with Ultima Premium tool steel increasing the grind life for extended punch use Fully guided for maximum support and accuracy at the punching surface Designed specifically for parting applications Available with one- and two-sided relieved strippers for use in close-to-clamp applications (thick turret only) Call or visit for more information.

23 THE ULTIMATE PARTING SOLUTION. COMPLETED. The Dura-Die parting tool completes Wilson Tool s ultimate parting solution. When combined with Wilson Tool s popular Dura-Blade product, you are able to greatly increase the life of your parting tools. When a new die is necessary, just replace the removable insert and you are quickly back up and running. Available only from Wilson Tool, the Dura-Die parting tool includes the following features: Unbeatable tool steel combination: The Dura-Die s replaceable die inserts are made from Wilson Tool s exclusive Ultima tool steel, allowing excellent wear resistance for maximum grind life. The die base is made from shock-resistant steel, allowing it to withstand even the highest punching force. Combined, these two steels give you the ultimate in durability and performance. Economical replaceable inserts just replace the die inserts for quick changeovers. These inserts are a lower cost alternative to replacing the entire die. Available for standard parting in C, D, and E stations close-to-clamp is available in D and E stations. Available with positive and SlugHugger2 relief options. For more information on the Wilson Dura-Die, contact your Wilson Tool Sales Engineer or call

24 23 Standard Keying Locations Punch View /2" (A) & -/4" (B) Station Die View Punch View 2" (C) Station Die View Punch View 3 /2" (D) Station Die View Punch View 4 /2" (E) Station Die View Standard Shapes SD DD LD QD ET OB SQ RT HX OT Single-D Double-D Long-D Quad-D EquilateralTriangle Obround Square Rectangle Hexagon Octagon

25 Non-Standard Keying 24 Die View When ordering shapes at non-standard angles, use the diagrams below to eliminate any confusion. Die View Front of Machine Wilson Tool s keying diagram. Shape at single angles other than standard (Note: No add'l charge on A & B stns for shape at 45 increments) Station /2" (A) -/4" (B) 2" (C) 3-/2" (D) 4-/2" (E) Guides or s Not Applicable Not Applicable Not Applicable Front of Machine This key location matches Amada s turret punch press programming method. Example Shape at 23 Standard keying, plus extra pins or keys for shapes at other than 45 increments Station /2" (A) Not Available Not Available -/4" (B) Not Available Not Available 2" (C) per pin per key 3-/2" (D) per pin per key 4-/2" (E) per pin per key Guides or s per key per key Not Available Not Available Not Available Standard keying, plus extra pins or keys for shapes at 45 increments Station Available Options Add On Available Options Add On Guides or s /2" (A) -/4" (B) 2" (C) 3-/2" (D) 4-/2" (E) Not Available 0 & 45 0 & Increments 45 Increments 45 Increments Not Available per pin per pin per pin Not Available 0 & 45 0 & Increments 45 Increments 45 Increments Not Available per key per key per key per key per key per key Not Available Not Available Not Available

26 25 Multi-Tools For Finn-Power Machines MT3Ri Description P&D ASSY Punch Driver Assy. Punch Driver Assy. Punch Driver Only s Slug Hugger * Standard Slug Hugger 2* Positive MT8Ri Description P&D ASSY s Slug Hugger * Standard Slug Hugger 2* Positive Negative MT8i Description P&D ASSY s Slug Hugger * Standard Slug Hugger 2* Positive Negative MT20i Description P&D ASSY s Slug Hugger * Standard Slug Hugger 2* Positive Negative Description MT 6-24 & MT 8-24 s (.750", 9.05mm Max 'A' dim) (7.756", 9.05mm 'A' dim) Slug Hugger * Standard Slug Hugger 2*.750 max Slug Hugger 2* >.750 Positive.750 max Positive >.750 Negative.750 max Negative >.750 MT Description s DIES Slug Hugger * Standard MT 6-6 & MT 0-6 Description s Slug Hugger * Standard Slug Hugger 2* Positive Negative $ MT 20-8 & MT 24-8 Description s Slug Hugger * Standard Slug Hugger 2* Positive Negative MT 6-6 Type Code Description Maximum 'A' Dimension of punch (mm) Number of stations in the holder Multi-Tool Notes For Multi-Tool add-ons, go to page 22. Ultima Premium Tool Steel is available on punches and dies. Contact sales desk for pricing and availability. * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.52mm) min. width on shapes,.006 (0.5mm) min. clearance (patented). Multi-Tool and Finn-Power are registered trademarks of Finn-Power International, Inc.

27 Multi-Tools For Nisshinbo Machines 26 WT Multi-Tool Holder 8-Station for 3-/2" (D) Station Description P&D Assy Locking Bracket -New Design -Old Design s dies Slug Hugger *.500 (2.7mm) max punch dia. >.500 (2.7mm) punch dia. Standard.500 (2.7mm) max punch dia. >.500 (2.7mm) punch dia. Slug Hugger 2*.500 (2.7mm) max 'A' dim. >.500 (2.7mm) 'A' dim. Positive.500 (2.7mm) max 'A' dim. >.500 (2.7mm) 'A' dim. Negative.500 (2.7mm) max 'A' dim. >.500 (2.7mm) 'A' dim. 8-6 RD SH 2 Die.500 (2.7mm) max punch dia SH 2 RD DIE 8-6 >.500 (2.7mm) punch dia >.500 (2.7mm) 'A' dim Note: Photos apply to 8-Station only. WT Multi-Tool Holder 20-Station for 3-/2" (D) Station Description P&D ASSY Locking Bracket s Slug Hugger * Standard Slug Hugger 2* Positive Negative Maximum punch 'A' Dimension is.630 (6mm). 'A' Dimension = Longest distance across shape. A locking bracket 3808 is required for 3-/2" (D) station auto index. Multi-Tool Add-Ons Standard Shapes Add ons for Rounds ET Equilateral SD Single-D DD Double-D LD Long-D QD Quad-D Triangle Small Width ( mm) ( mm) Punch Die Old Design OB Obround SQ Square RT Rectangle HX Hexagon OT Octagon Add-ons for Shapes Small Width Punch ( mm) ( mm) Die New Design Notes * Slug Hugger dies must be ordered punch size plus clearance,.098 (2.49mm) min. dia. on rounds,.060 (.52mm) min. width on shapes,.006 (0.5mm) min. clearance (patented). Multi-Tool is a registered trademark of Finn-Power International, Inc.

28 27 Accessories Tools Sure Shot Sprayer -QT (.95 liter) capacity 620 T-Handle extractor for large station guide assemblies 6483 SAE Hex Key Wrench Set 6057 Punch Lubricant 6055 Soft Face Hammer 606 Tru-Arc Pliers 6056

29 Accessories 28 Tools Rubberized abrasive wheel for removing galling 8050 Spanner Wrench 6058 Metric Hex Key Wrench Set 605 Oil Stone 6060 Diamond File 6059 Zip-Mar Adhesive Disks Station /2" (A) -/4" (B) 2" (C) 3-/2" (D) 4-/2" (E) Qty. pkg.(0) pkg.(0) pkg.(0) pkg.(0) pkg.(0) " x 2" (5.2 x 30.5cm) Sheet 608 Spring Disassembly Tool 804 Zip Mar reduces the costly marring of material by the stripper. The disk is applied to the bottom of a standard stripping guide or stripper plate. A hole is then cut with a sharp knife to reveal the existing hole in the stripper.

30 29 Accessories Tooling Cabinet Thick Turret Tooling Cabinet Options Plastic Drawer Liners Mobile Base Maple Top Cart Handle () Ribbed Rubber Mat Drawer Arrangement & Capacity Consisting of: 3 drawers for /2" (A) station tooling: 8 punch & guide assemblies (per drawer) 36 dies & 8 additional punches (per drawer) 3 drawers for -/4" (B) station tooling: 2 punch & guide assemblies (per drawer) 24 dies & 2 additional punches (per drawer) drawer for 2" (C) station and 3-/2" (D) station tooling: 2 2" or 3-/2" station punches, stripper plates and dies drawer (9 compartments) for 4-/2" (E) station tooling: 6" (F) station tooling, large station guide assemblies and misc. Cabinet includes lock with two keys and forklift base. Dimensions: 42" (07 cm) high x 28" (7 cm) wide x 29" (74 cm) deep. Standard color: Classic Blue Note: Tool cabinets are shipped motor freight-collect Shear Grinding Fixture and Accessories Description Shear Grinding Fixture 6034 /2" Tooling Sleeve Adapter /4" Tooling Punch and Die Holder /4" to /2" Die Adapter 6088 Series 80 /90 Tooling Punch Holder 6040 Dura-Blade Grinding Fixture 6932 Pointer (Replacement) 6035 Degree Scale (Replacement) 6036 Multi-Tool Punch and Die Holders Description 8 Station Thick/Thin Punch & Die Holder 682 8mm Punch & Die Holder 656 6mm Punch & Die Holder mm Punch & Die Holder 658

31 Accessories 30 Tool Kit Tool Kit consists of the following: () Tool Box, () Oil Stone, () Diamond File, () Tru-Arc Pliers, () Spanner Wrench, () Punch Lubricant, () Soft Face Hammer, () Metric Hex Key Wrench Set, () Hex Key Wrench Set (English), () Assortment of 4-sizes of square urethane ejectors. 609 Slug Ejectors Square Urethane Hole Dia. In Punch Qty. /8" (3.2mm) 50 3/6" (4.8mm) 50 3/8" (9.5mm) 50 /2" (2.7mm) 50 Assortment Center Punch Form-Down for /2" (A) Station Description Complete Form-Down Assembly (incl. die) 852 (.250" (6.35mm) max. mat.) Replaceable Center Punch Button 205 Punch Body 207 Guide 206 Blank Die 2267 Light Spring (for >.250" (6.35mm) mat.) 649 Form-Up for -/4" (B) Station -/4" (B) Station-Complete Set (not shown) -/4" (B) Station Upper Punch Assembly -/4" (B) Station Lower Die Assembly /4" (B) Station Replaceable Die Insert.375" (9.53mm) /2" (A) Station Form Down

32 3 Accessories Alignment Tools station /2" (A) -/4" (B) Alignment Tools for Amada Single Track Machines Upper Unit 2597 $ Lower Unit STATION /2" (A) -/4" (B) Alignment Tools for Amada Multiple Track Machines 260 * 2602 * *NOTE: Two of each required. Alignment Tools station 2" (C) 3-/2" (D) 4-/2" (E) 6" (F) Upper Unit Lower Unit In order to align A and B stations, you need either one or two tools for each size station, depending on the type of machine. For a single track turret, one tool is required to align each station. For a multiple track machine, two tools are required to align each station (one in the front of the station and one in the back).

33 Accessories 32 Adapters -/4" (B) To /2" (A) Station Adapter Description Punch & Guide Assembly Adapter (Keyed at 0 & 80 ) Die Adapter Screw " (C) To -/4" (B) Station Adapter Description Punch & Guide Assembly Adapter Die Adapter Screw /2" (D) To -/4" (B) Station Adapter Description Punch & Guide Assembly Adapter (not shown) Die Adapter /2" (E) To -/4" (B) Station Adapter Description Punch & Guide Assembly Adapter (not shown) 4-/2 Tk to -/4 Thk Die Adapter NOTE: Maximum material thickness for above adapters -.35" (3.4 mm) mild steel and aluminum,.090" (2.3 mm) stainless steel.

34 33 Accessories Ball Riding Die & Brush Die The Ball Riding Die, which consists of a spring loaded ball, has been designed to help eliminate several problems. The most common problems result from the higher height of the form-up dies. These problems are: Sheet hang-up from the material running into a higher die, such as a forming tool. Sheet deformation from punching next to dies of different heights. Damage to forming die inserts when the die cap receives uneven loading during punching in neighboring stations. Ball Riding Die STATION /2" (A) /4" (B) 482 2" (C) /2" (D) /2" (E) 3593 To reduce sheet and tool damage in forming applications, two of these dies are placed in stations surrounding the forming tool. When the sheet approaches the form-up die, it is lifted by the ball riding die. When the forming operation begins, the ball in the surrounding die recesses with the sheet. Once the form has been achieved and the tool strips, the spring loaded balls lift the sheet back to its original height. This allows the sheet to move more freely through the turret, avoiding collisions with the form-up tool. Placing these dies into the vacant stations on a turret loaded on one side can also eliminate material crashes. Brush Die station /2" (A) -/4" (B) 2" (C) 3-/2" (D) 4-/2" (E) The primary use for brush dies is in applications where any marking that might be caused by ball riding dies is not acceptable.

35 Accessories 34 Punch & Die shims Die Shims Die Shims Die Shims.00 Thick (0.25 mm).030 Thick (0.75 mm).060 Thick (.5 mm) Individually Individually Individually Station Qty. Station Qty. Station Qty. /2" (A) 20 /2" (A) 272 /2" (A) 204 -/4" (B) /4" (B) /4" (B) 200 2" (C) " (C) " (C) /2" (D) /2" (D) /2" (D) /2" (E) /2" (E) /2" (E) 2076 Package Package Package Station Qty. Station Qty. Station Qty. /2" (A) /2" (A) /2" (A) /4" (B) /4" (B) /4" (B) " (C) " (C) " (C) /2" (D) /2" (D) /2" (D) /2" (E) /2" (E) /2" (E) " (F) min 0 W200 6" (F) min 0 W200 6" (F) min 0 W200 6" (F) min 00 W200 6" (F) min 00 W200 6" (F) min 00 W200 Punch Shims.060 Thick (.5 mm) Shim Rack only 6588 Individually Package Shim Rack Hook 6589 Station Qty. Station Qty. Shim Rack with Die Shims 506 /2" (A) -/4" (B) /2" (A) -/4" (B) Must specify shim thickness.00, 030 or.060 -/4" (B) Metric 2" (C) /4" (B) Metric 2" (C) /2" (D) /2" (D) /2" (E) /2" (E) 5 27 Die Shims For Multi-Tools Machine Type Station Shape Thickness Individual Package of 5 ea. FINN-POWER 3-/2 8i/Ri.00" (0.25 mm) 6800 $ FINN-POWER 3-/2 8i/Ri.030" (0.76 mm) FINN-POWER MT 2 & 20 8 ROUND.00" (0.25 mm) FINN-POWER MT 2 & 20 8 ROUND.030" (0.76 mm) FINN-POWER MT 2 & 20 8 SHAPE.00" (0.25 mm) FINN-POWER MT 2 & 20 8 SHAPE.030" (0.76 mm) FINN-POWER MT 6 & " (0.25 mm) FINN-POWER MT 6 & " (0.76 mm) FINN-POWER MT 6 & " (0.25 mm) FINN-POWER MT 6 & " (0.76 mm) THICK TURRET -/4 5.00" (0.25 mm) THICK TURRET -/ " (0.76 mm)

36 35 Accessories Notcher Plate The Notcher Plate is: Hardened tool steel stripper plate. Precision ground to exacting tolerances. Uniquely designed to give the rigidity and slip fit of a special Notching Unit. What does this mean to you? Better guiding, less tool deflection. Greater flexibility of tooling applications. Longer tool life. Standard punch can be used. Notcher Plate Notcher Plate Notes Station 2" (C) Max. punch 'A' Dimension 2.000" (50.8 mm) Shape Round Shape Designed to fit Wilson Tool manufactured guide assemblies only. For larger sizes, please contact our sales desk. 3-/2" (D) 4-/2" (E) 3.500" (88.9 mm) 4.500" (4.3 mm) Round Shape Round Shape 'A' Dimension = Longest distance across shape. min. total clearance (patented).

37 Accessories 36 Wilson Punch & Die Grinder The Wilson Punch & Die Grinder is the latest in a long line of Wilson Tool products designed to help you work smarter not harder. Designed by DCM specifically for resurfacing punches and dies, it can save you time, space and money compared to existing sharpening methods. Here s how: 5 hp spindle motor. Handles large dies easily. CBN grinding wheel. Provides aggressive material removal rates and a high-quality surface finish. Dual coolant application. Coolant is supplied both externally and through the spindle for maximum heat removal while grinding helping to maintain tool integrity. Regrind punches up to 0 angle. The punch fixturing allows sharpening of rooftop and straight angle shear punches with angles up to 0 and everything in between. Simple fixturing design. Allows for quick, easy loading and unloading of parts and accurate, repeatable process control. Auxiliary magnetic chuck standard. Accommodates items that cannot be secured in the three-jaw chuck. Autofeed. Frees up the operator to perform other shop duties during the grinding process and allows for accurate cut depths. Heavy-duty three-jaw chuck standard. Will accommodate all punches and dies up to 6" (52 mm) diameter. Small footprint. At 40" x 48" (0 x 22 cm), the Wilson Punch and Die Grinder requires minimal floor space. In addition, the grinder comes standard with a rigid, heavy-duty 8" (45.7 cm) diameter rotary table that eliminates any chance for the chatter common with smaller tables. To learn more about the new Wilson Punch & Die Grinder and how to invest in this effective, economical means to maximize punch and die life, please contact your local Wilson Tool representative, or call our sales desk at Machine & Consumables Pricing Description 230V 3 Phase 30 Amp grinder 230V 3 Phase 30 Amp grinder - Enclosed 460V 3 Phase 20 Amp grinder 460V 3 Phase 30 Amp grinder - Enclosed 2 gallon coolant mix 5 gallon coolant mix The fully enclosed punch and die grinder includes an integral mist collection unit and provides full containment of the grinding area vs. the standard open air containment shrouding. Coolant filter pack (50 sheets) " replacement CBN wheel 6859 Production coolant filtration system 6860 Replacement filter roll for filtration system 686

38 37 TERMS OF SALE Order Minimum order is $50.00 Credit Requirements All orders are subject to approval by our Credit Department. If you are a new account, please furnish us with your tax exempt status, a bank reference, three current supplier references and/or your current D&B rating with your first order. A credit limit will be imposed on new accounts until credit has been established. Payment Terms Terms are net 0 days. Catalog prices are subject to change without notice. Freight Orders are shipped F.O.B. from our manufacturing facility. (International Shipments are Incoterms: Ex Works). Order Cancellation In the event an order is cancelled, an additional charge will be assessed to cover the cost of labor and material. Returned Material A handling/restocking fee will be applied to all standard products returned for credit. A return authorization number and shipping instructions must be obtained in advance before an item can be returned. Claims All claims or product shortages must be made within 30 days of the invoice date.

39 Notes

40 Wilson Tool International PRECISION TOOLING. UNBEATABLE PERFORMANCE. For more than 40 years, Wilson Tool International has provided industry-leading tooling solutions that enhance the performance of sheet metal fabricators and stampers worldwide. The three divisions of Wilson Tool Punching, Press Brake, and Stamping represent the most comprehensive line of tooling systems and accessories available. Our ability to consistently provide innovative, high quality products that outlast and outperform the competition is why the world s most successful fabricators rely upon Wilson Tool tooling systems. A knowledgeable global sales force, multilingual customer support staff, same-day shipping and extensive distribution network are just a few of the benefits that keep our customers coming back time and again. Wilson Tool International, Inc. - United States Tel (Free): Fax (Free): sales@wilsontool.com Wilson Tool International, Ltd. - United Kingdom Tel (Free): Tel: Fax (Free): Fax: or 46 sales@wilsontool.eu.com Wilson Tool International - China Tel: Fax: sales@wilsontool.cn Wilson Tool International - Germany Tel (Free): Tel: Fax (Free): Fax: verkauf@wilsontool.eu.com Wilson Tool International A/S - Denmark Tel (Free): Tel: Fax (Free): Fax: sales@wilsontool.dk Wilson Tool International - France Tel: +33 (0) Fax: +33 (0) ventes@wilsontool.eu.com Wilson Tool International - Argentina Tel: Fax: ventasargentina@wilsontool.com Wilson Tool - South Africa (Pty) Limited Tel: Fax: simon.penney@wilsontool.com The Wilson Tool Company S. de R.L. de C.V. - Mexico Tel: 52 (8) Fax: 52 (8) americalatina@wilsontool.com Exacta Precision Products - Ontario Tel: Fax: info@exactapunch.com Exacta FabTool - Ontario Tel: Fax: info@exactafabtool.com Punch Press Tooling Division 292 Farnham Avenue White Bear Lake, MN 550 Tel (Free): Fax (Free): Milling Puncionadeiras - Brazil Tel/Fax: vendas@milling.com.br P203C 202 Wilson Tool International