Powder Actuated Fasteners - Drive Pins

Transcription

1 122 Drive Pins Standard Pins Drive pins with a.300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. Drive Pin Sizes P /2" (knurled) P /8" (knurled) P /4" P /4" Black Pins P " P /8" P /4" P /2" P /4" P " P /4" P /8" P /2" P /4" P " With Top Hat The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track. P /2" knurled P /8" knurled P /4" P " Master Pack P /2" knurled P /4" Black Pins P /8" knurled P /8" knr. Top Hat P /4" P " P /4" P /2" knr. Top Hat P /4" Top Hat P " Top Hat Washered Pins To provide resistance to pullover, these pins are available with preassembled 14 gage (0.075") metal washers in various diameters. The insulation washer has a thickness of 0.035". with 3/4" Washer P /4" P /2" P " with 7/8" Washer P " P /4" P /2" P " P /2" P " with 1" Washer P /4" P /2" P " P /2" P "

2 123 Drive Pins (Cont.) 8mm Head Drive Pins (Cont.) P mm - 7/8" mm.143 P mm - 1" mm.143 P mm - 1-1/4" mm.143 P mm - 1-1/2" mm.143 P mm - 1-5/8" mm.143 P mm - 1-7/8" mm.143 P mm - 2" mm.143 P mm - 2-1/4" mm.143 P mm - 2-1/2" mm.143 P mm - 2-7/8" mm.143 Anchors with 1-7/16" Insulation Washer P /2" P /2" P " Head Step Shank Pins P /4" Step Shank /.130 P " Step Shank /.130 8mm Head Drive Pins X-DN Type Pins Drive pins with an 8mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. An 8mm plastic washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. 8mm Head Drive Pins P mm knrld - 5/8" mm.143 P mm knrld - 3/4" mm.143 8mm Diameter Head Drive Pins With Top Hat The pins listed below are used primarily for applications fastening drywall track to concrete or steel. They are assembled with a metal top hat to provide extra bearing surface against the drywall track. P mm knrld - 5/8" mm.143 P mm - 7/8" mm.143 P mm - 1" mm.143 8mm Head Drive Pins - Master Pack P mm knr. T Hat mm.143 P mm Top Hat mm.143 Washered Pins To provide resistance to pullover, these pins are available with preassembled 14 gage (0.075") metal washers in various diameters. 8mm Head Diameter Drive Pins With 1" Washer P mm - 1" mm.143 P mm - 1-1/4" mm.143 P mm - 1-1/2" mm.143 P mm - 2" mm.143 P mm - 2-1/2" mm.143 P mm - 2-7/8" mm.143 Drilling, Tapping Strut Firestop Contractor

3 124 Drive Pins And EIFS Pins 6mm Head Drive Pins Drive pins with a 6mm diameter head are designed for permanently fastening a fixture to concrete, some types of masonry, and A36 structural steel. The pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base materials. A 12mm metal washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. 6mm Head Drive Pins P mm knrld. - 5/8" mm.143 P mm knrld. - 3/4" mm.143 P mm - 7/8" mm.143 P mm - 1" mm.143 P mm - 1-1/4" mm.143 P mm - 1-1/2" mm.143 P mm - 1-5/8" mm.143 P mm - 1-7/8" mm.143 P mm - 2" mm.143 P mm - 2-1/4" mm.143 P mm - 2-1/2" mm.143 P mm - 2-7/8" mm.143 3/8" Head Drive Pins Drive pins with a 3/8" diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. The pins are manufactured with a 0.171" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. P " /8".171 P /4" /8".171 P /2" /8".171 P " /8".171 P /2" /8".171 P " /8".171 P /8" /8".216 (with step shank).188 Ballistic Point Drive Pins Power Point-Type Fasteners Premium drive pins with a.300 diameter head have a specially designed point to allow more consistent penetration into harder base materials. Will reduce failures in dense concrete and steel. Drive Pins are manufactured with a 0.150" diameter shank in various lengths. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. Ballistic Point Drive Pins (Black) P /2" Ballistic Pt Pin P /8" Ballistic Pt Pin P /4" Ballistic Pt Pin P /8" Ballistic Pt Pin Ballistic Point Step Shank Pins P /4" Ballistic Pt Pin /.150 P /8" Ballistic Pt Pin /.150 EIFS Pins EIFS is an acronym for Exterior Insulation & Finish Systems EIFS Pins with a.300 diameter read 1-1/2" length are designed for permanently fastening to concrete or concrete block, installation systems such as, waterproofing membranes, plastic sheeting, metal lathe and wire mesh for plaster and stucco systems. To provide resistance to pullover, these pins are pre-assembled onto a soft plastic diaphragm. Resistance to pullover is increased by the additional bearing surfaces that are provided by the diaphragm. No. Description Box Ctn. P50282 EIFS Fastener 1-1/2" pin & plastic washer

4 125 Threaded Studs, Assemblies And Assemblies & Assemblies are combinations of drive pins and stamped steel clips designed for special applications. The pins are held within the clip using either a dome mechanism or a metal top hat. Ceiling Clip Assemblies For applications suspending acoustical ceiling systems or light fixtures, several styles of angled clips are pre-mounted onto pins. Anchors Threaded Studs Threaded studs are available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required. The shank diameter for the threaded studs is 0.143" for the 1/4"-20 diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designs are available to increase performance in steel base materials. A plastic flute is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. On the 1/4"-20 threaded studs, a plastic cap is also provided to protect the threads of the fastener during the driving process. 1/4"-20 Threaded Studs Thread Shank Thread Shank No. Length Length Box Ctn. Dia. Dia. P /2" 1/2" K /4".143 P /4" 1/2" K /4".143 P /4" 3/4" /4".143 P /2" 1" /4".143 P /4" 1" /4".143 P /2" 1-1/4" /4".143 P /4" 1-1/4" /4".143 P /4" 1-1/4" /4".143 K=Knurled.300 Head Pins With Ceiling Clips Wire No. Description Box Ctn. Dia. Dia. Hole P " " P " " P " " P /4" " P /4" " Economy Clip Ceiling clip without dome 8mm Drive Head Pins With Ceiling Clips Wire No. Description Box Ctn. Dia. Dia. Hole P mm w/cc mm " P mm w/cc mm " Ballistic Point Drive Pin With Ceiling Clip P /4" with /.150 ceiling clip Drilling, Tapping Strut 3/8"-16 Threaded Studs Thread Shank Thread Shank No. Length Length Box Ctn. Dia. Dia. P /4" 3/4" K /8".205 P /4" 1" /8".205 P /4" 1-1/4" /8".205 K=Knurled Factory Mutual Research Corp. approved Pipe Hanger Components Pre-Assembled Pin and Clip For Ladd Tool (L1600) Wire No. Description Box Ctn. Dia. Dia. Hole P50438 Pre-assembled " Pin Clip P50440 Ladd Pin & " Washer Assembly Firestop Contractor

5 126 Assemblies & (Cont.) BX And EMT Conduit Clip Assemblies With BX Cable Clips For the electrical trade, BX and EMT conduit clips are provided in various sizes for attaching conduit to base materials. No. Description Box Ctn. Dia. Dia. P " (BX) P /4" (BX) With EMT Conduit Clips No. Description Box Ctn. Dia. Dia. P /2" EMT 1-1/4" P /2" EMT 1" pin TH P /2" EMT 1" pin P /4" EMT 1-1/4" P /4" EMT 1" pin TH P /4" EMT 1" pin P " EMT 1" pin TH mm Diameter Head Drive Pins With EMT Conduit Clips No. Description Box Ctn. Dia. Dia. P mm TH w/ 1/2" EMT mm.143 P mm TH w/ 3/4" EMT mm.143 P mm TH w/ 1" EMT mm.143 Rebar Basket Assemblies Rebar basket clips are typically used in highway construction and paving applications to hold the support baskets for the reinforcing bars in place while the concrete is being poured. 8mm Head Drive Pins With Rebar Basket Clip No. Description Box Ctn. Dia. Dia. P mm w/basket clip mm.143 P mm w/basket clip mm.143 P mm w/basket clip mm.143 P mm w/basket clip mm.143 P mm w/basket clip mm.143 P mm w/basket clip mm.143 Forming Pin For concrete forming applications, the 1-3/4" (44mm) pin is designed for fastening wood members up to 3/4" in thickness while the 2-1/2" (62mm) pin is designed for wood members up to 1-1/2" in thickness. The pin has a break off groove 1" from the point to allow the wood forming members to be easily removed. P mm - 1-3/4" P mm - 2-1/2" Fastener In addition to the assemblies, the following accessories are available for use with drive pins or threaded studs as indicated below. No. Description Box Ctn. P50400 Ceiling Clip (no pin) 9/32" & 5/16" holes P /4" - 20 thrd. coupling P /8" - 16 thrd. coupling P /4" - 20 eye coupling (1/4" Wire Hole) P /4" metal washer - 14 gage P /8" metal washer - 14 gage P " metal washer - 14 gage P50439 LADD Clip - No pin P50365 Domed Ceiling Clip - No pin P50375 Economy Ceiling Clip - No pin

6 127 Powder Actuated Fastener Guns Drive Pins And Tools Hammer Drive Pins No Powder Loads Required Hammer Drive Pins are designed for permanently fastening a fixture to concrete and some types of masonry. This fastener is designed for use in a standard hand tool and should not be used in a powder actuated tool. The pins are formed with a 1/4" diameter head on one end and a 0.140" diameter shank in various lengths. A 3/8" diameter steel washer is mounted over the point to retain the drive pin in the fastener guide of the tool providing guidance during the driving operation. This fastener is recommended for light duty static load applications where holding power is not a critical factor. It should not be used overhead. 1/4" Head Hammer Drive Pins Shank Head Shank No. Length Box Ctn. Dia. Dia. P /4" /4".140 P " /4".140 P /4" /4".140 P /2" /4".140 P " /4".140 Hammer Drive Setting Tool No. Description Box Ctn. P50310 Hammer Drive Tool - Standard 1 1 P7200 Size Range: 1/2" to 1-1/2" pin lengths,.22 caliber The P7200 is a low velocity, single shot.22 caliber tool which can be used to install.300" head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs up to 1-1/2" in total length. The P7200 is commonly used in the drywall trade. P7200 Deluxe Kit Contents P7200 powder actuated tools are packaged in a deluxe kit box as listed below. P52004 P7200 Tool (Deluxe Kit) 1 P /8" Allen Wrench 1 P /32" Allen Wrench 1 P /4" Wire Brush 1 P /4" Wire Brush 1 P52336 Spall Guard 1 P52040 P7200 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. Anchors Drilling, Tapping Strut Firestop P ' Dielectric Pole Tool 1 P ' Dielectric Pole Tool 1 Contractor

7 128 Powder Actuated Fastener Guns (Cont.) P2200 Size Range: 1/2" to 3" pin lengths,.22 caliber The P2200 is a low velocity, single shot,.22 caliber tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs, up to 3" in total length. The P2200 is designed for maintenance or residential contractors. P2200 Deluxe Kit Contents P52006 P2200 Tool (Deluxe Kit) 1 P /16" Allen Wrench 1 P /4" Wire Brush 1 P /4" Wire Brush 1 P52550 Spall Guard P P52042 P2200 Tool Manual 1 P3500 Size Range: 1/2" to 3" pin lengths,.27 caliber The P3500 is a low velocity, semi-automatic,.27 caliber tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs, up to 3" in total length. The P3500 is designed for high speed and repetitive volume applications. P3500 Deluxe Kit Contents P52000 P3500 Tool (Deluxe Kit) 1 P mm Allen Wrench 1 P mm Allen Wrench 1 P /8" Wire Brush 1 P " Wire Brush 1 P /4" Wire Brush 1 P52166 Stabilizer P P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52036 P3500 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P ' Dielectric Pole Tool 1 P ' Dielectric Pole Tool 1

8 129 Powder Actuated Fastener Guns (Cont.) For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P ' Dielectric Pole Tool 1 P ' Dielectric Pole Tool 1 Anchors P35s Size Range: 1/2" to 1-1/2" pin lengths,.25 caliber The P35s is specially designed for acoustical and drywall contractors. It is a low velocity, semi-automatic, tool which can be used to install.300 head drive pins, 8mm head drive pins and 1/4" - 20 threaded studs up to 1-1/2" in total length. The P35s is designed for high speed and repetitive volume applications. The standard version of the tool is supplied with a flat end piston and a full size baseplate/guide. A limited access baseplate/guide assembly is also available. P35s Deluxe Kit Contents FA35s Size Range: 1/2" to 1-1/2" pin lengths,.25 caliber The FA35s is a modified version of the P35s that allows the operator to install pins, 1/4-20 threaded studs and assemblies faster than ever before. The operator who uses the FA35s no longer needs to manually cycle the tool in order to advance the load strip. The spring-loaded baseplate and guide automatically advances the next live load when the tool is compressed against the work surface. All the operator needs to do is feed the next pin. FA35s Deluxe Kit Contents P52015 FA35s Tool (Deluxe Kit) 1 Drilling, Tapping P52002 P35s Standard Tool (Deluxe Kit) 1 P52003 P35s Ltd. Access (Deluxe Kit) 1 P mm Allen Wrench 1 P mm Allen Wrench 1 P /8" Wire Brush 1 P " Wire Brush 1 P /4" Wire Brush 1 P52222 Stabilizer P35s 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52038 P35s Tool Manual 1 P mm Allen Wrench 1 P mm Allen Wrench 1 P /8" Wire Brush 1 P " Wire Brush 1 P /4" Wire Brush 1 P52222 Stabilizer P35s 1 P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52038 P35s Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P ' Dielectric Pole Tool 1 P ' Dielectric Pole Tool 1 Strut Firestop Contractor

9 130 Powder Actuated Fastener Guns (Cont.) PA3500 Size Range: 1/2" to 3" pin lengths,.27 caliber The PA3500 is a modified version of the P3500 that includes a power adjuster, allowing the operator to effectively decrease the power level of the load being used. A red load can be toned down to the level of a green. PA3500 Deluxe Kit Contents P52019 PA3500 Tool (Deluxe Kit) 1 P mm Allen Wrench 1 P mm Allen Wrench 1 P /8" Wire Brush 1 P " Wire Brush 1 P /4" Wire Brush 1 P52166 Stabilizer P P52120 Shear Clip (2) 1 P52122 Steel Annular Ball (2) 1 P52036 P3500 Tool Manual 1 For fastening ceiling clips overhead, 6' and 8' dielectric pole tools are available. P ' Dielectric Pole Tool 1 P ' Dielectric Pole Tool 1 Powder Loads Powers offers high quality powder loads, produced by the largest manufacturer in the United States, with unsurpassed quality and reliability. Specific load types are designed for each unique powder actuated tool. They are offered as single units for single shot tools and collated in groups of 10 into plastic strips or metal discs for semi-automatic tools..22 Caliber A Low Velocity Loads For Powers P7200, P2200, Ramset 721 and M70, Hilti DXE37 and DXE72 Master No. Description Box Ctn. Ctn. P50500 Gray,.22A P50502 Brown,.22A P50504 Green,.22A P50506 Yellow,.22A Caliber Loads For Ladd Ceiling Master Tool (L1600) Master No. Description Box Ctn. Ctn. P50514 Green - Ladd P50516 Yellow - Ladd P50518 Red - Ladd Caliber Disk Loads For Ramset D45, D60, D60L Master No. Description Box Ctn. Ctn. P50530 Gray,.25 disk P50532 Brown,.25 disk P50534 Green,.25 disk P50536 Yellow,.25 disk Caliber Red Disk Loads For Ramset Model D45 Master No. Description Box Ctn. Ctn. P50538 Red,.25 disk Ramset is a registered trademark of Illinois Tool Works, Inc. Hilti is a registered trademark of Hilti, Inc.

10 31 BRIGHTON-BEST FLAT HEAD SOCKET CAP SCREWS - COARSE THREAD 1/ ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /16 Hex 3/ ,000 FSC44034 T10 TORX ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /64 Hex 5/ ,000 FSC54058 T10 TORX 3/ ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /64 Hex 5/ ,000 FSC63258 T15 TORX 3/ ,000 FSC ,000 FSC / ,000 FSC ,000 FSC6322 1/ ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /32 Hex 7/ ,000 FSC83278 T20 TORX ,000 FSC / ,000 FSC / ,000 FSC ,000 FSC8322 3/ ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /8 Hex 7/ ,000 FSC T25 TORX ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC /4-20 7/ ,000 FSC ,000 FSC /32 Hex 1 1/ ,000 FSC T30 TORX 1 1/ ,000 FSC / ,000 FSC ,000 FSC / ,000 FSC ,000 FSC / ,000 FSC ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / ,000 FSC / / ,000 FSC ,000 FSC /16 Hex 1 1/ ,000 FSC T40 TORX 1 1/ ,500 FSC / ,000 FSC ,000 FSC / ,000 FSC / ,000 FSC ,000 FSC / ,000 FSC / ,000 FSC / ,500 FSC /8-16 7/ ,500 FSC ,500 FSC /32 Hex 1 1/ ,000 FSC T45 TORX 1 1/ ,000 FSC / FSC FSC / FSC / FSC FSC / FSC / ,500 FSC / ,000 FSC / ,000 FSC /4 Hex 1 1/ FSC T50 TORX 1 3/ FSC FSC / FSC / ,500 FSC / ,000 FSC FSC / FSC / FSC / / FSC FSC /16 Hex 2 1/ FSC T50 TORX 2 1/ FSC FSC / FSC FSC / FSC FSC FSC12136 Anchors Drilling, Tapping Strut Firestop Contractor

11 132 Powder Load Strips (Cont.), Trak-It Fuel Cells.27 Caliber Safety Strip Loads - Master Pack No. Description Box Ctn. P50624 Green,.27 Safety Strip P50628 Yellow,.27 Safety Strip P50632 Red,.27 Safety Strip Trak-It Fasteners Use In: Concrete, Block and A36 Steel Size Range: 1/2" to 1-1/2" Pin Lengths Anchor Material: Carbon Steel Trak-It Fasteners and the Trak-It Fuel Cell are designed to be used with the Powers Trak-It Tool* and can also be installed with the ITW Ramset TrakFast tool. Then fasteners are collated on each patented, plastic top hat-style strip. Use for light duty static applications such as drywall track to concrete, block or steel, lath to concrete or block, furring strips to concrete or block, and plywood to concrete or block base materials. The fuel cell, with its unique right angle metering valve, contains enough gas to install up to 1200 fasteners. Each package contains 1000 fasteners and 1 fuel cell. Trak-It Fasteners / Trak-It Fuel Cell No. Shank Length Box Ctn. P /2" Trak-It Pin Zinc & Fuel Cell P /4" Trak-It Pins & Fuel Cell P " Trak-It Pins & Fuel Cell P /4" Trak-It Pins & Fuel Cell P /2" Trak-It Pins & Fuel Cell P55012 Trak-It Lathing Washer *Powers Trak-It Tool is currently in test market. Trak-It Fuel Cell No. Shank Length Box P55010 Trak-It Fuel Cell 10 * Powers Trak-It Tool is currently in test market. Multi Purpose Case No. P0278 Ramset is a registered trademark of Illinois Tool Works, Inc. TrakFast is a trademark of Illinois Tool Works, Inc. TIP For fastener technical specifications, please visit our web site at and click on technical specifications.