Installation Manual -R007 Garden Feature Nook

Transcription

1 Installation Manual -R007 Garden Feature Nook YM11560 (1.99m) Yardistry Ltd. - North merica Toll Free Customer Support: info@yardistrystructures.com Yardistry / Selwood Products - Europe Customer Support: parts@selwoodproducts.com (1m) (2.17m) Revised 04/06/2011 (1.18m) 1

2 !Important Safety Notice! Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: - safety barrier to prevent unsupervised access to pools, hot tubs, spas, or ponds. - Safety railings for elevated platforms or decks. - s load bearing support for a building, structure, heavy objects or swings. - Used in structures that trap wind, rain or snow that would create extra load on the product. Permanent structures may require a building permit. s the purchaser and or installer of this product you are advised to consult local planning, zoning, and building inspection departments for guidance on applicable building codes and or zoning requirements. Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user smanual of the grill, fire pit or chimneafor safe distances from combustible materials. During installation, follow all safety warnings provided with your tools and use OHS approved safety glasses. Some structures may require two or more people to install safely. Check for underground utilities before digging or driving stakes into the ground! General Information: Wood components are manufactured with Cedar (C. Lanceolata) which is protected with factory applied water-based stain. Knots, small checks (cracks) and weathering are naturally occurring and do not affect the strength of the product. nnual application of a water-based water repellant sealant or stain will help reduce weathering and checks. Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions. Tape Measure Carpenters Level Carpenters Square Standard or Cordless Drill This identifies information that requires special attention. Improper assembly could lead to an unsafe or dangerous condition. Patents Pending Tools Required #2 Phillips or Robertson djustable Wrench Bits or Screwdriver 1/8 Drill Bit Ratchet with extension (7/16 sockets) 1/4 Drill Bit Open End Wrench Pencil (7/16 ) 8 Step Ladder Keys To ssemble Success Safety Glasses dult Helpers Check that set or assembly is properly level before proceeding. Use Level Use Help Measure Distance Use Help Where this is shown, 2 or 3 people are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help! Check that assembly is square before tightening bolts. Use a measuring tape to assure proper location. Square ssembly Pre-drill 1/8 & 3/16 Bit Pre-drill a pilot hole before fastening screw or lag to prevent splitting of wood. This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. Tighten Bolts 2 No Yes

3 Material List Nominale 2" x 4" 5/4" x 3" ctuel 1½" x 3½" 1" x 2½" B C Y (2) 2 x 4 x 80" Y (2) 2 x 4 x 41 " Y (6) 5/4 x 3 x 54¼" S1 (36) #10 x 1" S4 S5 #8 x 2 1/4 Wood Screw #10 x 1 Pan Head Screw (12) 5/4 x 3 (Y ) S6 #10 x 1 1/2 Pan Head Screw S7 #8 x 1 1/2 Wood Screw BE (8) 2x4 Beam Ends (4) Post Top Connector With WH 7/16 Hex Bolt ssembly RB (2) Top and Bottom Rail 78-1/2 RS (4) Top and Bottom Rail 39-1/2 (18) Panel Clips 3

4 Material List PX1 (8) One High X Topper PL2 P PX2 (4) Two High Lattice Panel (4) Two High X Panel (4) 4 Post 4

5 Step 1- ssemble Screens for Main Wall 1. Remove the upper metal connectors on both sides of PL2 - Two High Lattice Panel. Reattach the metal connectors to PL2 by securing the bottom two holes of the metal connectors to the top two holes on PL2 so that the metal connectors stick out from the top. Slide PX1 One High X Topper between the two protruding metal connectors on the top of PL2. ttach the metal connectors to PX1. (Fig. 1) *Ensure Panels are oriented correctly! (Fig. 1B) 2. Secure panels with a S4-2 1/4 Wood Screw the location indicated by the large arrow in the direction of the arrow. 3. Repeat until 4 panel assemblies are created. PX1 Pilot holes to the right Pilot holes to the right Fig. 1B - Filler Strips on Bottom of Panel! x4 Fig. 1 PL2 PX1 One High X Topper S4 #8-2 1/4 Wood Screws PL2 Two High Lattice Panel 5

6 Step 2- ssemble main Wall les petites pièces nt. Small Connectors. nectores Fig. 1 ssemble Toppers to Panels. 1 Instale los topes en los paneles. Insérez les pièces de raccordement mâles dans les pièces de raccordement femelles. Faites glisser le panneau vers le bas jusqu'à ce qu'il soit au même niveau que le panneau adjacent. 2x R Top & Bottom Rail at 6 6 1/2 (2m) 21x S4 #8-2 1/4 Wood Screws les petites pièces ctory nt. drilled holes. ros pretaladrados. répercés à l'usine ssemble panels together in configuration shown. (Fig.1) Insert male connector into female. Slide down until flush with adjacent Pautas básicas para Instruc panel Basic Guidelines as shown. (Fig. el ensamblado 1) de pour l' for Panel ssembly los paneles des pa ssemblez les pièces Pautas supérieures básicas para Instructions de base 3 Cut and atta 2. Secure Shown here are configurations Panels using Las ilustraciones muestran Les assem et les panneaux. with S4-2 1/4 a Topper. 2 and 3 High Panels can configuraciones con topes. También pièces supé Basic Guidelines el ensamblado de pour l'assemblage screws also be connected provided together as se pueden conectar 2 in pre-drilled Corte y 3 paneles y également fije l purchased. altos a medida que se adquieran. à deux ou à for Panel ssembly los paneles des panneaux holes *Use 2 1/4" stainless as indicated steel screws *Use by los arrows, tornillos de acero inoxidable (vendus sé in included in the Panel Clip set to de 2 1/4" que se incluyen en el juego *Utilisez les Shown here are configurations + using Las ilustraciones muestran Les assemblages illustrés comportent des Taillez et fix = B. ssemble the secure Panels and direction strengthen side by the side. assembly. of (Maximum the de arrow. sujetadores de 3 wide (Fig.1) paneles para 2-1/4 po fou x 3 high) reforzar el ensamblado. fixations po a Topper. 2 and 3 High Panels can configuraciones con topes. También pièces supérieures. Il est possible renforce Conecte los paneles lado a lado. also be connected together as se pueden conectar 2 y 3 paneles également d'assembler des panneaux One Wide ssemblez 2 les panneaux côte ssemble à côte. Panels side by side. purchased. altos a medida que se adquieran. à deux ou à trois carreaux de hauteur 20" Conecte Fig. 1los paneles lado a lado. *Use 2 1/4" stainless Remove steel Large screws *Use los tornillos de acero inoxidable (vendus séparément). Connectors and reattach using top two factory drilled holes on panel. ssemblez les panneaux côte à côte. included in the Panel Clip set to Pautas de 2 1/4" que básicas se incluyen en para el juego Instructions *Utilisez les vis en acier de inoxydable base de 3 Cut and atta Retire los conectores grandes y vuelva a instalarlos secure usando los dos agujeros pretaladrados del panel. Basic and Guidelines strengthen the assembly. de sujetadores de paneles para 2-1/4 fournies dans le nécessaire de el ensamblado de pour l'assemblage Two Wide Corte y fije l Retirez les grandes pièces de raccordement reforzar et fixez-les ensamblado. fixations pour panneaux afin de fixer et for Panel ssembly de nouveau au moyen des deux los trous paneles des Note de renforcer Notez l'orientation l'assemblage. orientation de l'encoche en supérieurs du panneau qui ont été percés of keyhole. trou de serrure. Shown here are configurations à l'usine. using Las ilustraciones muestran Les assemblages illustrés comportent des Taillez et fix a Topper. 2 and 3 High Panels can configuraciones con topes. También 2 ssemble Panels side by side. also be connected together as se pueden conectar 2 y 3 paneles Conecte los paneles lado a lado. purchased. altos a medida que se adquieran. *Use 2 1/4" stainless steel screws ssemblez *Use los les tornillos panneaux de acero côte inoxidable à côte. included in the Panel Clip set to de 2 1/4" que se incluyen en el juego secure and strengthen the assembly. de sujetadores de paneles para reforzar el ensamblado. Tenga en cuenta la orientación del agujero de la cerradura. pièces supérieures. Il est possible Three Wide également d'assembler des panneaux One Wide à deux ou à trois carreaux de hauteur 20" (vendus séparément). Insert male into female. Slide down until flush with adjacent panel *Utilisez les vis en acier inoxydable Introduzca de el extremo macho en el extremo hembra. 3. Connect Deslícelo last asse ha abajo hasta que quede al ras del panel adyacente. Four Wide 2-1/4 po fournies dans le nécessaire de Two Wide Insert male Insérez into les female. pièces de raccordement Slide down mâles until dans flush les pièces with fixations pour adjacent panneaux de panel. raccordement afin femelles. de fixer Faites et glisser le panneau vers le bas jusqu'à ce qu'il soit au même niveau que de renforcer Introduzca l'assemblage. le panneau el extremo adjacent. macho en el extremo hembra. Deslícelo hacia abajo hasta que quede al ras del Do not remove Small Connectors. panel adyacente. Three Wide No retire los conectores Insérez les pièces de raccordement mâles dans Rles pequeños. pièces de raccordement femelles. Faites glisser le panneau vers le bas jusqu'à ce qu'il soit au même Ne retirez pas les petites pièces de raccordement. niveau que le panneau adjacent. Fig. 2 Notez l'orientation 3. Secure R-Top and de l'encoche en 2 ssemble Panels side by side. trou de serrure. Bottom Rails to Panel ssembly with S4-2 1/4 Note wood Conecte piece at bottom prevents los paneles lado a lado. collection of water. Wood Screws locations Note que la ssemblez pieza de madera inferior les panneaux côte à côte. evita la acumulación de agua. indicated by arrows in Prenez note que la pièce en bois située au bas de chaque élément the direction of the arrow. de l'assemblage empêche l'accumulation d'eau. (Fig. 2) Insert male into female. Slide down until flush with adjacent panel. Secure with Screws*. Use factory drilled holes. Notez l'orientation *R- Top and Bottom Rails segure el ensamblado usando tornillos*. Use los agujeros pretaladrados. de l'encoche will en overhang 1/4 on Introduzca el extremo Fixez macho l'assemblage en au el moyen extremo de vis.* Servez-vous hembra. des Deslícelo trous prépercés hacia à l'usine. trou de serrure. abajo hasta que quede al ras del panel adyacente. either side of panel. Insérez les pièces de raccordement mâles dans les pièces * R- Top and Bottom Rails panel_cap_labels_19x9.5.indd 7 de raccordement femelles. Faites glisser le panneau may need vers to le bas be jusqu'à cut to ce qu'il soit au même niveau que 6 6 le 1/2 panneau (2m) adjacent. C. (It is recommended to Small Connectors. Insert male into female. Slide down until flush with adjacent panel. use a Mitre Box or Mitre nectores Introduzca el extremo macho en el extremo hembra. Deslícelo hacia Saw) abajo hasta que quede al ras del panel adyacente. 3. Connect last assembled panels to make a fence section. Remove the male connectors from the outside of the panel assembly. Quite los conectores masculinos del exterior de la asamblea de panel. 3. Connect last assembled Enlever les panels connecteurs to make mâles a fence de section. l'extérieur de l'assemblée de panneau. Screws* are 2 1/4" stainless steel included in Panel Clip set. Los tornillos* son de acero inoxidable de 2 1/4" y se incluyen en el juego de sujetadores de paneles. *Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le nécessaire de fixations pour panneaux. Los torn y se incluyen *Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le male connector conector masculino short male connector conector masculino corto le connect Top and RBottom mâle Rail court will overhang 1/4" 1/4"on either s ttach Top with Screws* through factory drilled hol On Bottom, space Screw 4" 1/4" from edges of panels. 1/4" Four Wide Top and Bottom Rail will overhang 1/4"on either s ttach Top with Screws* through factory drilled connecte hol mâle On Bottom, space Screw 4" from edges of panels.

7 Step 3- ssemble Side Walls 1. Remove the upper metal connectors on both sides of PX2 - Two High X Panel. Reattach the metal connectors to PX2 by securing the bottom two holes of the metal connectors to the top two holes on PX2 so that the metal connectors stick out from the top. Slide Px1 One High X Topper between the two protruding metal connectors on the top of PX2. ttach the metal connectors to Px1. (Fig. 1) *Ensure Panels are oriented correctly! (Fig. 1B) 2. Secure panels with a S4-2 1/4 Wood Screw the location indicated by the large arrow in the direction of the arrow. 3. Repeat until four panel assemblies are created. PX1 Pilot holes to the right Fig. 1B - Filler Strips on Bottom of Panel! Fig. 1 PX2 x4 PX1 One High X Topper S4 #8-2 1/4 Wood Screws PX2 Two High X Panel 7

8 Step 4- ssemble Side Wall Fig. 1 ssemble Toppers to Panels. 1 Instale los topes en los paneles. ssemble Panels side by side. Conecte los paneles lado a lado. ssemblez les Note wood piece at bottom prevents collection panneaux of water. côte à côte. 3. Secure R-Top and Bottom Rails to Note que la pieza de madera inferior evita la acumulación de agua. Panel ssembly with S4-2 1/4 Wood Prenez note que la pièce en bois Screws locations indicated située au by bas de arrows chaque élément in de l'assemblage empêche l'accumulation d'eau. the direction of the arrow. (Fig. 2) Insert male into female. Slide down until flush with adjacent panel. *R- Top and Bottom Rails will overhang 1/4 Introduzca on either el extremo side macho of en panel. extremo hembra. Deslícelo hacia abajo hasta que quede al ras del panel adyacente. * R- Top and Bottom Rails may need to z les pièces be de cut raccordement to size mâles indicated dans les in pièces material list panel_cap_labels_19x9.5.indd 7 cordement femelles. Faites glisser below. le panneau e bas jusqu'à ce qu'il soit au même niveau que neau adjacent. (It is recommended Insert male into female. to use Slide down a Mitre until flush Box with adjacent panel. or Mitre Saw) Introduzca el extremo macho en el extremo hembra. Deslícelo hacia 4. Repeat abajo to hasta create que two quede walls. ras del panel adyacente. ez les pièces de raccordement mâles dans les pièces ccordement femelles. Faites glisser le panneau le bas jusqu'à ce qu'il soit au même niveau que nneau adjacent. Secure with Screws*. Use factory drilled holes. segure el ensamblado usando tornillos*. Use los agujeros pretaladrados. 3. Fixez Connect l'assemblage last au assembled moyen de vis.* Servez-vous panels to des make trous prépercés a fence à l'usine. section. R Top & Bottom Rail at 3 3 1/2 (1m) 18x S4 #8-2 1/4 Wood Screws 8 1. ssemble panels together in configuration shown. (Fig.1) Insert male connector into female. Slide down until flush with adjacent Pautas básicas para Instruc panel Basic Guidelines as shown. (Fig. el ensamblado 1) de pour l' for Panel ssembly los paneles des pa ssemblez les pièces supérieures Pautas 2. Secure Shown here are configurations Panels using Las ilustraciones muestran Les assem et básicas les panneaux. para Instructions de base 3 Cut and attach Top and Bottom with S4-2 1/4 a Topper. 2 and 3 High Panels can configuraciones con topes. También pièces supé ic Guidelines el ensamblado de pour l'assemblage screws also be connected provided together as se pueden conectar 2 y 3 paneles également Corte y fije in los pre-drilled rieles superior purchased. altos a medida que se adquieran. à deux e ou ià anel ssembly los paneles des panneaux holes *Use 2 1/4" stainless as indicated steel screws *Use by los arrows, tornillos de acero inoxidable (vendus sé in included in the Panel Clip set to de 2 1/4" que se incluyen en el juego *Utilisez les + = B. ssemble the secure Panels and direction strengthen side by the side. assembly. of (Maximum the de arrow. sujetadores de 3 wide (Fig.1) paneles para 2-1/4 po fou here are configurations using Las ilustraciones muestran Les assemblages illustrés comportent des Taillez et fixez la main courante x 3 high) reforzar el ensamblado. fixations po er. 2 and 3 High Panels can configuraciones con topes. También pièces supérieures. Il est possible x2 de renforce Conecte los paneles lado a lado. connected together as se pueden conectar 2 y 3 paneles également d'assembler des panneaux One Wide ncho sencillo Une pièc ssemblez 2 les panneaux côte ssemble à côte. Panels side by side. sed. altos a medida que se adquieran. à deux ou à trois carreaux de hauteur 20" 20" Cut and Conecte Fig. attach 1los paneles Top lado and a lado. Pautas Bottom Remove básicas Large Connectors and para Instructions de base 3 1/4" stainless steel screws *Use los tornillos de acero inoxidable (vendus séparément). reattach using top two factory drilled holes on panel. ssemblez les panneaux côte à côte. ic Guidelines el ensamblado de pour l'assemblage d in the Panel Clip set to de 2 1/4" que se incluyen el juego *Utilisez les vis en acier inoxydable de Retire los conectores grandes y vuelva a instalarlos Corte y fije los rieles superior e Panel ssembly los paneles des panneaux usando los dos agujeros pretaladrados del panel. and strengthen the assembly. de sujetadores de paneles para 2-1/4 po fournies dans le nécessaire de Two Wide ncho doble Deux piè reforzar Retirez les grandes pièces de raccordement et fixez-les de nouveau au moyen des deux trous Note Tenga en cuenta Notez l'orientation here are configurations using Las ilustraciones el ensamblado. fixations muestran Les assemblages pour panneaux illustrés afin comportent de fixer et des 39½" de Taillez et fixez la main courante orientation la orientación del de l'encoche en supérieurs du panneau qui ont été percés of keyhole. agujero de la trou de serrure. per. 2 and 3 High Panels can configuraciones con topes. También pièces renforcer supérieures. l'assemblage. Il est possible à l'usine. cerradura. One Wide ncho sencillo Une piè e connected together as se pueden conectar 2 y 3 paneles également d'assembler des panneaux ssemble Panels side by side. Three Wide ncho triple Trois pièces 20" 20" sed. altos a medida que se adquieran. à deux ou à trois carreaux de hauteur 1/4" stainless steel screws *Use los tornillos de acero inoxidable (vendus séparément). 59" Conecte los paneles lado a lado. ed in the Panel Clip set to de 2 1/4" que se incluyen en el juego *Utilisez les vis en acier inoxydable de ssemblez les panneaux côte à côte. and strengthen the assembly. de sujetadores de paneles para 2-1/4 po fournies dans le nécessaire de reforzar el ensamblado. fixations pour panneaux afin de fixer et de renforcer l'assemblage. Insert male into female. Slide down until flush with adjacent panel Two Introduzca Wide el extremo ncho macho en doble el extremo hembra. 3. Connect Deux Deslícelo last piè asse ha Four abajo Wide hasta que quede ncho al ras del cuádruple panel adyacente. Quat 39½" Insert male Insérez into les female. pièces de raccordement Slide down mâles until dans flush les pièces with 78½" adjacent de panel. raccordement femelles. Faites glisser le panneau vers le bas jusqu'à ce qu'il soit au même niveau que Introduzca le panneau el extremo adjacent. macho en el extremo hembra. Deslícelo hacia abajo Three hasta Wide que quede ncho al ras del triple Trois pièces Do not remove Small Connectors. panel adyacente. 59" No retire los conectores Insérez les pièces de raccordement mâles dans les pequeños. R pièces de raccordement femelles. Faites glisser le panneau vers le bas jusqu'à ce qu'il soit au même Ne retirez pas les petites pièces de raccordement. niveau que le panneau adjacent. Four Wide ncho cuádruple Qua 78½ Fig. 2 C. Top and Bottom Rail will Los torn x2 y se incluyen *Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le Remove the male connectors from the outside of the panel assembly. overhang 1/4"on either side. Quite los ttach conectores Top with masculinos Screws* del exterior de la 3. Connect last assembled panels to make a fence asamblea section. through de panel. factory drilled holes. Enlever les On connecteurs Bottom, space mâles Screws* de l'extérieur de l'assemblée de panneau. Screws* are 2 1/4" stainless steel included in Panel Clip set. Los tornillos* son de acero inoxidable de 2 1/4" y se incluyen en el juego de sujetadores de paneles. *Les vis sont celles de 2-1/4 po en acier inoxydable qui sont fournies dans le nécessaire de fixations pour panneaux. 4" from edges of panels. Top and RBottom Rail will overhang 1/4"on either side. ttach Top with Screws* through 1/4" factory drilled holes. On Bottom, space Screws* 4" from edges of panels. 1/4" 1/4" male connector conector masculino Los rieles superior e inf a cada lado. Fije el tope en los agujeros pretalad connecte inferior, deje un mâle espacio tornillos* y los bordes d short male connector conector masculino corto Los rieles superior e in a cada lado. Fije le connect el top en los agujeros mâle pretala court inferior, deje un espaci tornillos* y los bordes d 4" }

9 Step 5- ttach Panel Clips Back posts 1. On a flat surface place P- 4 Post on its side and position Panel Clips in locations indicated in Figures 1 and 1. Ensure Panel Clips are oriented as shown in Diagrams! 2. Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3/8 or 3.5cm away from the side of the post as shown in Fig With Panel Clips in place, mark screw holes with a pencil and pre-drill holes with a 1/8 drill bit. (Not provided) 4. Secure Panel Clips in locations indicated in figure 1 and 1 with S7- #8 x 1 1/2 wood screws. Fig /8 (3.5cm) Pre-drill holes and secure with S7- #8 x 1 1/2 Wood Screws Fig.1 Top View B C D Front View Fig /4 (142.9cm) 40 (101.6cm) (25.3cm) P 4 Post 18x - Panel Clips 36x S7 #8 x 1 1/2 Wood Screw 9

10 This identifies information that requires special Step 6- ttach attention. Panels Improper assembly to could Posts lead to an unsafe or dangerous condition. Check that set or assembly is properly level before proceeding. Use Use Pre-drill 1/8 & 3/16 Bit Where this is shown, 2 or 3 1. Place panel assemblies Help on posts as Helpshown (Fig.1) allowing a 4 gap between the bottom of the post and the people are required to safely Pre-drill a pilot hole bottom edge of the bottom rail on the panel assembly. Note: ssemble with the help of another adult. complete the step. To avoid before fastening screw 2. With a 1/8 drill bit, predrill holes as shown injury figure or damage 2. to the or lag to prevent assembly make sure to get help! splitting of wood. 3. Fasten the panel assembles to the post and Panel Clips with a S5-1 Pan Head Screw provided in location of circles. (Fig. 1) Measure Check that assembly is square Square Distance before tightening bolts. ssembly B Use a measuring Fig. tape 1 to Back assure View proper location. D CUTION Protrusion Hazard Once the assembly is tightened, watch for exposed threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition. Extra washers have been provided for this purpose. Proper Hardware ssembly Lag screws require drilling pilot holes to avoid splitting wood. Only a flat washer is required. For ease of installation liquid soap can be used on all lag-type screws. Note: Wafer head bolts with blue lock tight or a bolt with a Ny-Lok nut do NOT require a lock washer. Lag Screw 6 This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. No Lag ssembly If Bolt protrudes beyond T-Nut Use an extra Flat Washer D For bolts, tap T-Nut into hole with hammer. Insert the hex bolt through lock washer first then flat washer then Flat Washer hole. Because the assemblies need 4 to (10.2cm) Bolt ssembly Hex Bolt be squared do not completely tighten Left Side until View instructed. B Pay close attention to Lock Right Side View Washer diameter of the bolts. 5/16 is slightly larger than 1/4. C Flat Washer C Tigh Bo Ye Before mounting use factory drilled guides to drill 1/8 T-Nut (Hammer Do not cr Fig. 2. Predrill Holes and Fasten with S5-1 Pan Head Screw 12x P 4 Post 18x S5 #10 x 1 Pan Screws 10

11 This identifies information that requires special Check that set or assembly is properl 20" attention. Improper assembly 78½" could lead to an before proceeding. 20" unsafe or dangerous condition. 20" Installer le Poteau 4 x 4 po et le Connector de Poteau 4 x 4 po. L espace Use entre Poteau Use 4 x 4 po et la direction de Poteau Pre-drill 1/8 & 3/16 Bit Where this is shown, 2 or 3 connecteur Help et critical. Help people are required to safely Pre-drill a pilo complete the step. To avoid before fasteni injury or damage to the or lag to prev assembly make sure to get help! splitting of wo 1. Layout rbour bases in configuration shown in figure 1. *Posts must be securely installed to support structure.consult Measurelocal Check building that assembly codes is and square ground Square conditions for required footing design. It is recommended Distance before the tightening structure bolts. be secured to ssembly existing stone, concrete or deck with the Yardistry Post Base (YM21016) 177 " or 177 equivalent " hardware. This indicates time to tighten bolts, b not too tight! Do not crush the wood. 2. Install Post Top Connectors with S6- Use 1 1/2 a measuring Pan Head tape Screws to assure provided. (Fig. 2) This Ensure may create the splinters and cause proper location. direction of the Post Top Connector is the same direction as indicated by the arrows structural in figure damage ½" 78½" No Step 7- Layout Posts and 20" Connectors CUTION Protrusion Hazard Once the assembly is tightened, watch for exposed threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition. Extra washers have been provided for this purpose. Proper Hardware ssembly 132½" Lag ssembly Lag screws require drilling pilot Lag Screw holes to avoid splitting wood. Only a flat washer is required. For ease of 20" installation liquid soap can be 20" Fig. used 1 on all lag-type screws. Install on a flat For 20" bolts, tap T-Nut into and hole level with surface! 20" hammer. Insert the hex bolt through lock washer first then flat washer then Flat Washer hole. Because the assemblies 78½" need to Bolt ssembly Hex Bolt be squared do not completely tighten until instructed. Pay close attention to Lock Washer diameter of the bolts. 5/16 is slightly larger than 1/4. Note: Wafer head bolts with blue lock tight or a bolt with a Ny-Lok nut do NOT require a lock washer. Flat Washer 6 If Bolt protrude beyond T-Nut Use an extra Flat Washer Be use gu Fig. 2 - ttach Post Top Connectors with S6-1 1/2 Pan 5 Head Screws. 16x S6 1 1/2 Pan head Screws - Post Top Connector 11

12 Step 8- ssemble Roof 1. ttach two - 2 x 4 x 80 Beams to Post Top Connectors with WH-7/16" Hex Bolt as shown in Fig. 1 and Centre two B-2 x 4 x 41 1/8 Beams in place and attach to Post Top Connectors with WH-7/16" Hex Bolt as shown in Fig. 1 and 1. Drill 1/4 Holes for bolts using holes in Post Top Connector as guides. 3. ttach eight BE- 2 x 4 Beam Ends to Post Top Connectors with WH-7/16 Hex Bolt as shown in Fig. 1 and Evenly space apart and secure six C-5/4 x 3 x 54¼ Trellis to Beams using 5/4 x 3 Brackets and S1- #10-1 Pan Screws as shown in figures 1 and 2. BE C Fig. 1 B BE BE B 39½" 78½" (1.00m) BE (1.99m) Fig. 2 S1 5/4 x 3" C BE Fig. 1 B Drill 1/4 holes for bolts using holes in Post Top Connector as guides Taladre agujeros de 1/4" para los pernos usando los agujeros delconector superior Drill de poste 1/4 comoguía Holes for bolts using holes in Post Top Connector as guides. Percez des trous de 1/4 po (6,35 mm) pour les boulons en utilisant les trous des connecteurs de bout de poteau comme guides 36x S1 #10-1 Pan Screw 2x 2 x 4 x 80 Beam 6x C 5/4 x 3 x 54 1/4 trellis 12x -5/4 x 3 Bracket 2x B 2 x 4 x 41 1/8 Beam 32x WH 7/16 Hex Bolt w/ Nut 8x Z 2 x 4 Beam Ends 12