48" STAINLESS STEEL ROLLING WORKBENCH CT1996

Transcription

1 48" STINLESS STEEL ROLLING WORKBENCH CT1996 INSTRUCTION BOOKLET CUTION Please take safety precautions when using the tool chest. o New drawer glides may be stiff and difficult to open when first expanding the glide. gentle outward pull should release the safety catch that is built into the glide to prevent drawer opening while moving the tool chest. o Gently set parts on a flat, protective surface. o Do not open more than one drawer at a time. o Do not step or climb on drawers. o Do not let children near the tool chest. o Fill the bottom drawer first. If the tool chest is filled from the top drawer down, then the tool chest will be top-heavy and might fall over. o Set the brake on locking casters unless you are moving the tool chest. o Lock drawers and lid before moving the chest. o Make sure all drawers are closed tightly before closing the lid. THIS INSTRUCTION BOOKLET CONTINS IMPORTNT SFETY INFORMTION. PLESE RED ND KEEP FOR FUTURE REFERENCE. Page 1 of 6

2 MXIMUM LOD CPCITY MXIMUM LOD 1,130 lb / kg FOR WOOD TOP (EVENLY DISTRIBUTED) B C D C B C MXIMUM LOD 15 lb / 6.8 kg MXIMUM LOD 25 lb / 11.3 kg MXIMUM LOD 40 lb / 18.2 kg FOR DRWERS (EVENLY DISTRIBUTED) D MXIMUM LOD 60 lb / 27.3 kg FOR CBINET (EVENLY DISTRIBUTED) ENTIRE UNIT MXIMUM CPCITY: 1,540 lb / 700 kg Concentrated Load Capacities (per square foot): Wood Top : 175 lb / 79.5 kg Cabinet: 30 lb / 13.6 kg Small Drawer: 5 lb / 2.3 kg Middle Drawer: 5 lb /2.3 kg Large Drawer: 10 lb / 4.5 kg GENERL INFORMTION, TIPS & HELPFUL HINTS 1. Please read instructions prior to assembly. 4. Recommend to use 2 people for assembly. 2. Verify that there are no missing parts. 5. Do not tighten any bolts until all bolts have been started. 3. Keep instructions for future reference. 6. For indoor use. Page 2 of 6

3 Parts and Hardware List Please read completely through the instructions and verify that all parts listed are included before beginning assembly. Tools required for assembly: Wrench (not included). - Tool Chest (1) B- Side Handle (2) C- Small Bolt (8) D- Swivel Caster (2) E- Locking Caster (2) F- Large Bolt (16+1 extra) G- Key (2) Page 3 of 6

4 Handle ssembly Instructions 1 Unpack the unit and confirm that you have all the hardware and required parts listed. 2 Stand the unit upright and attach Side Handle (B) to Tool Chest () securing with Small Bolts (C) as shown below figure. 3 Repeat step for the other side handle. Note: ssemble the unit on a sturdy and level surface. void assembling on carpet. You should place the unit on a protective surface when assembling to the unit to prevent scratching or damage to any of the surfaces. Hardware required Sketch QTY (B)- Side Handle (2) (C)- Small Bolt (8) Tools required for assembly: Wrench Caster ssembly Instructions Page 4 of 6

5 4 ttach Locking Casters (E) and Swivel Casters (D) to the bottom of Tool Chest with Large Bolts (F). Securely tighten all the bolts with Wrench. Make sure the Locking Casters (E) locate at same side of the unit. Note: Please adjust the bins and liners in the drawers after finishing the casters. Hardware required Sketch QTY (D)- Swivel Caster (2) (E)- Locking Caster (2) (F)- Large Bolt (16) Tools required for assembly: Wrench CRE & MINTENNCE Use a soft, clean cloth that will not scratch the surface when dusting. Using solvents of any kind on the wood top may damage the finish. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. void rubbing Page 5 of 6

6 CNNON TOOLS LTD dd: 20 station road, Rowley Regis, west midlands,b65 0JU.U.K. 6 of 6 Made in China