DRAWING TABLE SYSTEM

Size: px

Start display at page:

Download "DRAWING TABLE SYSTEM"

Cecily Dickerson
5 years ago
Views:

1 DRWING TBLE SYSTEM DT31, DT61S, & CDTC71 MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 1 OF 6 REV 11/30/2015 7:12:32 M, DWG To PDF.pc3

2 TOOLS REQUIRED 1 2 " WRENCH 1 2 " SOCKET ND TORQUE WRENCH OPTIONL 4MM LLEN WRENCH SCREW DRIVER SSEMBLY COMPONE ITEMS INCLUDED PRT # PRT QTY TOP ND ON SSEMBLY N/ TOP SSEMBLY (FCTORY SSEMBLED) 1 CBINET N/ CBINET "W X 26.50"D X 27"H 1 LEGS LEG,MPL 2.25X2.25X LEG HRDWRE KIT LEG HRDWRE KIT, 4 LEGS 1 LEG BRCE N/ LEG BRCE 24.00" LONG 2 STRETCHER N/ STRETCHER 37.50" LONG 1 CONFIRMTS LEGS CONFIRMTS STRETCHER SCREW,7MMX90MM,CONN,LLENHED, BLCK SCREW,7MMX50MM,CONN,LLENHED, BLCK BRCKETS CBINET BRCKET,RIL 25X25X SCREWS BRCKET SCREW,#8X 3 4 PHIL TRUSS HED SMS 12 PENCIL LEDGE PENCIL LEDGE 1 SCREWS PENCIL LEDGE SCREW,#6X 3 4 TRUSS HED,QUD,BLCK 3 **CPU SUPPORT** N/ SUPPORT,CPU,EB4,00X7.00X **SCREWS CPU SUPPORT** SCREW,#8X1 1 4 SQ. WSHER FLT HED 6 **CPU BRCKET** BRCKET,MOUNTING,CPU UNIT 1 **KEYBORD TRY KIT** TRY,KEYBORD,SLIDE OUT,#KVKD100 1 **MONITOR BSE SSEMBLY** HFELE MONITOR BSE SSEMBLY 1 **MONITOR RM** HFELE FLT SCREEN RM **XX** INDICTES ITEMS ONLY USED FOR THE CDTC7 : : TOOLS ND SSEMBLY COMPONE CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 2 OF 6 REV 11/30/2015 7:12:39 M, DWG To PDF.pc3

3 FRONT LEG ON SIDE FCING UP INSERT HNGER BOLT THROUGH HERE WITH LOCK WSHER ND HEX NUT FRONT ON LEG WITH CHMFER NEEDS TO BE FCING OUT (REPET ON OTHER FRONT LEG) CLOSE UP OF CORNER LEG SSEMBLY CLOSE UP OF LEG WITH CHMFER STEP 1: LY ON SSEMBLY ON FLOOR WITH ON SIDE FCING UP. BE SURE TOP SSEMBLY IS ON CLEN SURFCE TO PREVENT DMGE. STEP 2: INSERT HNGER BOLT ON ONE OF THE LEGS THROUGH THE CORNER BRCKET ND INSERT LOCK WSHER ND HEX NUT. USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH, SCREW ON THE NUT BUT DO NOT TIGHTEN LL THE WY. REPET FOR THE OTHER 3 LEGS. THE LEGS WITH CHMFER MUST GO ON THE FRONT OF THE TBLE WITH CHMFERED EDGES FCING OUT. : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 3 OF 6 REV 11/30/2015 7:12:45 M, DWG To PDF.pc3

4 LEG LEVELER STRETCHER LEG BRCES BRCKETS BCK EDGE OF CBINET BRCKET CLOSE UP OF LEG LEVELER SSEMBLY TOP OF CBINET SHOWN STEP 3: SCREW LEG LEVELERS INTO TNUT ON BOTTOM OF LEGS. STEP 4: USING 4MM LLEN WRENCH INSERT THE CONFIRMTS INTO ONE LEG ND SCREW INTO BRCE. REPET FOR THE OTHER LEGS. MKE SURE BRCES RE STRIGHT ND LL CONFIRMTS RE TIGHT. TTCH STRETCHER TO THE BRCES USING CONFIRMTS PROVIDED. GO BCK TO STEP 2 ND TIGHTEN UP THE HNGER BOLTS FOR ECH LEG USING 1 2" WRENCH OR 1 2" SOCKET ND TORQUE WRENCH, TO MINIMUM OF 12FT LBS BUT NOT TO EXCEED 17FT LBS. STEP 5: TTCH TWO BRCKETS TO THE TOP OF THE CBINET WITH THE SCREWS PROVIDED. PLCE THE BRCKETS SLIGHTLY BCK FROM THE EDGE OF THE CSE. THIS WILL HELP THE BRCKETS TO CLER THE ONS WHEN YOU LOWER THE CSE INTO PLCE : : TITLE: CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 4 OF 6 REV 11/30/2015 7:12:51 M, DWG To PDF.pc3

5 BCK ON KEYBORD MOUNTING BORDS BCK BRCKET (FRONT NOT SHOWN) KEYBORD TRY BOTTOM BRCKET FRONT ON TOPS REMOVED TO SHOW CLRITY TOPS REMOVED TO SHOW CLRITY STEP 6: WITH HELP FROM T LEST TWO PEOPLE, TIP TBLE ON ITS SIDE SO RIGHT SIDE OF TBLE IS ON FLOOR. FCE THE DRWERS TO THE FRONT OF THE TBLE ND THE TWO TOP BRCKETS TOWRDS THE TBLE TOP. FIT BOTH BRCKETS INSIDE THE FRONT ND BCK ONS. LOWER CBINET ONTO THE TBLE LEGS. SCREW THE LST BRCKET ONTO THE STRETCHER ND BOTTOM OF CBINET WITH SCREWS PROVIDED. STEP 7: TTCH THE TWO BRCKETS ON TOP OF THE CBINET TO THE ON SSEMBLY. REMOVING ONE OF THE KEYBORD MOUNTING BORD WILL MKE IT ESIER TO FSTEN BRCKETS TO ON SSEMBLY. HOLES NEED TO BE PREDRILLED BEFORE TTCHING BRCKETS TO ONS. STEP 8: IF YOUR TBLE DOES NOT HVE KEYBORD TRY OR CPU SUPPORT SKIP TO STEP 1 TTCH KEYBORD TRY TO THE TWO KEYBORD MOUNTING BORDS WITH THE HRDWRE PROVIDED. IT MY BE ESIER TO TTCH KEYBORD TRY WHILE TBLE IS ON ITS TOP. TTCH THE MONITOR POST TO TOP USING HRDWRE PROVIDED (NOT SHOWN). : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 5 OF 6 REV 11/30/2015 7:13:02 M, DWG To PDF.pc3

6 CPU SUPPORT CPU BRCKET DJUSTBLE TOP PENCIL LEDGE TOPS, KEYBORD TRY, ND KEYBORD MOU REMOVED TO SHOW CLRITY TOPS, KEYBORD TRY, ND KEYBORD MOU REMOVED TO SHOW CLRITY COMPLETE UNIT SHOWN STEP 9: STEP 10: STEP 11: TTCH THE CPU SUPPORT TO THE LEG BRCE ND ON SSEMBLY WITH THE SCREWS PROVIDED.THE SUPPORT SHOULD LY FLUSH GINST THE BOTTOM OF THE LEG BRCE ND STRETCHER. THERE WILL BE SMLL GP BETWEEN THE TOP OF THE ON SSEMBLY ND TOP OF THE SUPPORT. INSTLL THE CPU BRCKET TO THE SUPPORT USING THE PPROPRITE HRDWRE FOR YOUR PPLICTION. LINE UP PENCIL LEDGE ON SIDE OF DJUSTBLE TOP IN DESIRED LOCTION. SCREW PENCIL LEDGE TO TOP USING SCREWS PROVIDED. HOLES NEED TO BE PREDRILLED TO PREVENT TOP FROM SPLITTING. SET YOUR TBLE IN PLCE ND DJUST THE LEG LEVELERS TO LEVEL TBLE. : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: DT31, 61S, & CDTC71 SCLE: 6 OF 6 REV 11/30/2015 7:13:12 M, DWG To PDF.pc3

DRAWER BASE DRAWING TABLE

DRAWER BASE DRAWING TABLE MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 1 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:08 M, DWG To PDF.pc3 TOOLS REQUIRED 1 2 " WRENCH 1