Installation Guide Tilt/Swivel Flush Mount for 23'' and Larger Flat Panel Displays
|
|
- Bertram Boone
- 5 years ago
- Views:
Transcription
1 Installation Guide Tilt/Swivel Flush Mount for 23'' and Larger Flat Panel isplays WRNING: This mounting system has a weight limit of 100 lbs [45.36 kg]. o not mount a display weighing more than 100 lbs [45.36 kg] on this Tilt/Swivel Flush Mount. The purpose of this guide is to describe installation of the mount and mounting a display on the mount. Parts Reference The following parts and hardware are included in this installation kit (hardware not shown: Item # escription Qty 1 Tilt/Swivel Flush Mount ssembly 1 2 Mounting dapter 1 3 M4 x 14 mm Pan Head Machine Screw (PHMS) 4 4 M4 x 12 mm PHMS 4 5 M4 x 10 mm PHMS 4 6 M6 x 16 mm Socket Head Machine Screw (SHS) 4 7 M6 x 14 mm SHS 4 8 5/16-18 Lock Nut, Nylon 4 9 Washer,.750 x.320 x /8'' Hex Wrench /16'' Hex Wrench /2'' Socket Wrench Tools Required Phillips screwdriver (not provided) 1/8'' hex wrench (provided) 3/16'' hex wrenches (provided) 1/2'' socket wrench (provided). U-FLP Rev 9/08/08 GX orp. Page 1 of 6
2 Mounting Flush Mount in hannel 1. Guide hannel Slide (rear of Mount) into top of channel and move to desired mounting position. Using the 1/8'' hex wrench provided, tighten four (4) socket set screws (below right) to secure Mount in hannel. Tighten Set Screws Tighten Set Screws Existing hannel U-FLP Rev 9/08/08 GX orp. Page 2 of 6
3 Mounting a 23'' to 31'' isplay Installation Note: The display must be equipped with a 100 x 100 mm or 100 x 200 mm VES mounting pattern for attachment to the Tilt/Swivel Flush Mount. M4 pan head machine screws (PHMS) are included for different depths of threaded inserts in the VES mounting pattern. 1. etermine required length of M4 mounting screw for fastening display to Mount. 2. Thread two (2) M4 PHMS into the upper two (2) mounting holes of the VES mounting pattern (rear of display), leaving 5mm of thread exposed (upper illustration). Hang display on Mount by guiding these two (2) screws into the slots on top of the Mount. 100 x 200 mm Mounting Pattern 100 x 100 mm Mounting Pattern M4 PHMS (2) with 5 mm Exposed Thread Upper Slots 3. Thread two (2) M4 PHMS into the lower mounting holes and tighten all four (4) mounting screws. 100 x 100 mm Mounting Pattern 100 x 200 mm Mounting Pattern M4 PHMS (2) M4 PHMS (2) U-FLP Rev 9/08/08 GX orp. Page 3 of 6
4 Mounting a 31'' (iagonal) or Larger isplay Installation Note: The Mounting dapter (provided) must be used when mounting larger displays on the Tilt/Swivel Mount. M6 socket head cap screws (SHS) and M4 pan head machine screws (PHMS) are included for different depths of threaded inserts on the rear of the display. Various possible mounting patterns are shown below. WRNING: The Mounting dapter must be attached to the Tilt/Swivel Flush Mount with four (4) slots oriented upward as shown in below. Failure to attach the Mounting dapter with slots up could cause the display to fall off the Mount. The following table lists available mounting patterns and screw size required for each mounting pattern. See Parts Reference on page 1 for screw sizes included in this installation kit. Mounting patterns are identified below right. Pattern Size of Mounting Pattern Screw Size 100 mm x 300 mm M4 PHMS WRNING: Slots Must Face Upward 100 mm x 300 mm M6 SHS 200 mm x 200 mm M6 SHS 200 mm x 400 mm M6 SHS 1. Using the 1/2'' wrench provided, fasten the Mounting dapter to the Tilt/Swivel Mount with four (4) 5/16-18 Lock Nuts and 0.75 x 0.32 Washers as shown in illustration below. WRNING: Slots Must Face Upward 0.75 x 0.32 Washers (4) Mounting dapter 5/16-18 Lock Nuts (4) U-FLP Rev 9/08/08 GX orp. Page 4 of 6
5 2. etermine required mounting screw (M6 SHS or M4 PHMS) for fastening display to Mounting dapter. 3. Thread four (4) screws' into the 4-hole mounting pattern on the rear of display, leaving 5mm of thread exposed. Hang display on Mount by guiding screws into the corresponding slots and keyholes in the Mounting dapter. 4. Using the 3/16'' hex wrench (provided) for socket head screws or Phillips screwdriver (not provided) for pan head screws, tighten all mounting screws. Hang Upper SHS (2) in Slots or Keyholes Insert Lower SHS (2) in Keyholes djusting Tilt 1. Using a 1/2'' wrench on each end of the bolt, loosen the rear tilt bolt and tilt display to desired position. Note: It may be necessary to loosen the front tilt bolt slightly to allow the display to tilt. 2. With display at desired tilt, tighten the rear tilt bolt. Tighten front tilt bolt if necessary. djusting Swivel Tension 1. Remove plastic bolt cap from each end of swivel bolt (below). 2. Using a 1/2'' wrench on each end of the bolt, tighten or loosen bolt to achieve desired swivel tension. 3. Replace bolt caps. olt aps (2) Swivel olt Rear Tilt olt Front Tilt olt U-FLP Rev 9/08/08 GX orp. Page 5 of 6
6 Routine Maintenance Periodically inspect all mounting hardware. Tighten or adjust as necessary for optimal operation and safety. leaning the Mounting ssembly 1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). 2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and trichloroethylene. 3. o not use steel wool or other abrasive material to clean the mounting assembly. 4. amage caused by the use of unapproved substances or processes will not be covered by warranty. We recommend that any cleaning solution be tested on a small area of the mounting assembly that is not visible to verify compatibility. 5. Never submerge or allow liquids to enter the mounting assemblies. Wipe any cleaning agents off the mounting assembly immediately using a water-dampened cloth. ry all mounting assemblies thoroughly after cleaning. UTION: GX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection. onsult your hospital s infection control officer or epidemiologist. To clean or sterilize mounted instruments or accessory equipment, refer to the specific instructions delivered with those products. U-FLP Rev 9/08/08 GX orp. Page 6 of 6
Installation Guide. Cabinet Surface Mount for Single Display
Installation Guide Cabinet Surface Mount for Single Display The purpose of this guide is to: 1. Describe the procedure for attaching Channel to cabinet top. 2. Describe the procedure for mounting the Column
More informationInstallation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe installation of MP40/50/60/70 mounting equipment on the anesthesia machine.
More informationInstallation Guide Mounting Kit Philips MP70/EGM/FMS on Dräger Fabius Tiro
Installation Guide Mounting Kit Philips MP70/EGM/FMS on Dräger Fabius Tiro The purpose of this guide is to describe mounting of parts on the anesthesia machine. WARNING: USE OF MOUNTING HARDWARE AND MONITORING
More informationInstallation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe mounting of MP90 equipment on the anesthesia machine. WARNING: USE OF MOUNTING
More informationInstallation Guide VHM Arm with 8'' Extension/Swivel Stop & 6'' Riser for Mounting Philips MP90 on Dräger Apollo
Installation Guide VHM Arm with 8'' Extension/Swivel Stop & 6'' Riser for Mounting Philips MP90 on Dräger Apollo The purpose of this guide is to describe mounting of MP90 equipment on the anesthesia machine.
More informationInstallation Guide Philips IntelliVue MP20/30/40/50/60/70 MX400/450/500/550/600/700/800 M-Series Arm Mounting Kit for Dräger Primus Anesthesia Machine
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Philips IntelliVue MP20/30/40/50/60/70 MX400/450/500/550/600/700/800 M-Series Arm Mounting
More informationInstallation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine
Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of Counterweight (page 2). 2. Describe
More informationGEMSIT Tram-rac 4A Module Housing Installation Kit
Installation Guide GEMSIT Tram-rac 4A Module Housing Installation Kit This mounting kit provides the necessary parts and hardware for attaching a single Tram-rac 4A to an M-Series or VHM Arm, or for attaching
More informationInstallation Guide Installation Kit for Mounting Philips MP20/30/40/50/60/70 on GE Healthcare Aisys Carestation
Installation Guide Installation Kit for Mounting Philips MP20/30/40/50/60/70 on GE Healthcare Aisys Carestation The purpose of this guide is to: 1. Describe mounting of Top Plate/Camlock Rail Assembly
More informationGCX Mounting Assembly Installation Guide. Drager Narcomed GS Anesthesia Machines with Philips MP60/70 IntelliVue Patient Monitor Kit
GCX Mounting Assembly Installation Guide Drager Narcomed GS Anesthesia Machines with Philips MP60/70 IntelliVue Patient Monitor Kit Philips MP60/70 IntelliVue Patient Monitor AGM Philips M8048A Flexible
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationInstallation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400
Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationMedium Flat Panel Dual Swing Arm Wall Mount JWD-V
INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationSpeaker Mount Center Channel Speaker Adapter (PAC-301)
I N S T R U C T I O N M A N U A L Speaker Mount Center Channel Speaker Adapter () The Speaker Mount Center Channel Speaker Adapter () uses the same interface as the Side Speaker Adapter and can be used
More informationINSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320
INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationFlat Panel Dual Swing Arm Wall Mount (FWD-110) MSP-SA
INSTALLATION INSTRUCTIONS Flat Panel Dual Swing Arm Wall Mount (FWD-110) The dual arm wall mount was designed to support flat panel displays with 10 to 30 diagonal screens and weighing a maximum of 40
More informationINSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationINSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225 KTP-440 / KTP-445
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More information3 wide x 3 deep Video Wall Display Installation Guide
HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame
More informationInstallation and Assembly: Flat-Panel Base Lock-Down Kit for Samsung Display Models
Installation and ssembly: Flat-Panel Base Lock-own Kit for Samsung isplay Models Models: HLG452-SM, HLG452-SM-Q10 Maximum isplay Size: 100 lb (45.35 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More informationUser and Installation Manual. For Tandem Arm and Slim Line Models. Tandem Arm. Slim Line
Tandem Arm User and Installation Manual For Tandem Arm and Slim Line Models Tandem Arm Slim Line Table of Contents Warnings... 4 Box Contents... 5 Hardware Kits... 6 Parts... 7 Tandem Arm Installation...
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationInstallation and Assembly - Desktop Swivel Mount For 32" - 55" Flat Panel Display
Installation and ssembly - Desktop wivel ount For 32" - 55" Flat Panel Display odels: HP455 ax Load apacity: 75 lb (34 kg) IUED: 2012-06-28 HEET #: 125-9328-4 (2017-10-20) NOTE: Read instruction sheet
More informationTYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side
TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationINSTITUTIONAL LIFEGUARD STAND
INSTITUTIONAL LIFEGUARD STAND ASSEMBLY INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 (503) 266-2231 Fax (503) 266-4334
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationSmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide
SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationINSTALLATION GUIDE Ceiling TV Mount MHP-52
ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD FORD ESCAPE
INSTALLATION INSTRUCTIONS GRILLE GUARD 08-010 FORD ESCAPE PARTS LIST: 1 Grille Guard 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Frame Mounting 4 10mm Lock Washers 1 Passenger/Right Frame Mounting 6 10mm
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More information4 BAY Low Profile-Dual Displays WALL MOUNT CABINET
D1/347M2 SSEMLY INSTRUTIONS 4 Y Low Profile-Dual Displays WLL MOUNT INET TIP HZRD WRNING! abinet must be affixed to wall. For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More information1. TOOLS + MATERIALS REQUIRED
R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationINSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS
INSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS The Universal Interface Bracket provides a solution for simplifying inventory of RPA and RPM series mounts and SLB/SLM projector brackets.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD CHEVY TAHOE / AVALANCHE 1500/ SUBURBAN 1500 PART # /502795
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 502794/502795 PARTS LIST: 1 Grille Guard 2 12-1.75mm x 140mm Hex Bolts 2 Frame Mounting Brackets 8 12-1.75mm x 30mm Hex Bolts 2 Lower Support Brackets
More informationInstallation and Assembly: Wallmount for CPA100 and Whiteboard
Installation and ssembly: Wallmount for CP100 and Whiteboard Model: 100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 Visit 3215 the
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More information(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) DODGE RAM 1500 QUAD CAB PART #DZ /DZ /DZ /DZ
(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) PART #DZ 372231/DZ 372233/DZ 372237/DZ 372239 PARTS LIST: 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) Qty Description Qty Description
More information40670 Transit Connect/NV200/City Express/ProMaster City Partition
40670 Transit Connect/NV200/City Express/ProMaster City Partition Top Panel (1) Bottom Panel (1) Transit Connect (2014) Top Angle (1) TC Top MNT BRKT (2) TC Bottom MNT PLT (2) NV200/City Express Top Mount
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More informationModel D3348 Extension Block Kit Instruction Sheet
INTRODUCTION Model D3348 Extension Block Kit Instruction Sheet Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz This Extension Block Kit increases the maximum
More informationVintage Kitchen in Pink Assembly Instructions
2010 KidKraft, LP WARNING: ADULT ASSEMBLY REQUIRED. Product includes small parts with potentially hazardous sharp points and sharp edges in the unassembled state. Keep unassembled parts away from children.
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationB B B
Winchester SXP Gauge Tactlite Six Position Adjustable Shotgun Stock with Scorpion Recoil System B..0.00 B..0.00 B..0.00 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationToyota Extend-A-Fender Fender Flares Set of 4
Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationMobile Cart for Flat Panel Display MSP-SPTC42 (PTC-2000 Series)
INSTALLATION INSTRUCTIONS Mobile Cart for Flat Panel Display (PTC-2000 Series) The Mobile Cart for Flat Panel Display is designed to assist the presenter in showrooms, boardrooms, and trade show exhibits.
More informationPART #MSP-DCCST Flat Panel Tilt Mount
INSTALLATION INSTRUCTIONS PART # Flat Panel Tilt Mount The Flat Panel Tilt Mount is a quick disconnect mounting solution for flat panel displays. The mount features adjustability between 0 and 15 degrees
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationTruss Pitch-Adjustable (TPP) Mount
I N S T R U C T I O N M A N U A L Truss Pitch-Adjustable (TPP) Mount The Truss Pitch-Adjustable (TPP) mount is a perfect solution exhibit, retail and digital signage applications. The mount is quick, easy
More informationInstallation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS
Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand
More informationMSP-DCCPGTU Large Screen Tilt Display Mount
INSTALLATION INSTRUCTIONS Large Screen Tilt Display Mount The Large Screen Tilt Display Mount is a quick disconnect mounting solution for large flat panel displays. The mount features infinite adjust ability
More informationCRITICAL INFORMATION:
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationPFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS
Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation
More informationNEC Display Solutions of America, Inc.
NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NEC NP400, NP500, NP500W, and NP600 Projectors Model: NP600CM Maximum Load Capacity: 50 lb (22.7 kg) Features:
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PROTRAXX OVAL STEP BAR APPLICATION: 2009-2017 Dodge Ram 1500 Crew/Quad Cab 2010-2017 Dodge Ram 2500/500 Crew Cab PART NUMBER: 21-550, 21-555, 21-50, 21-55 AUTOMOTIVE PRODUCTS,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS E-SERIES STEP BARS / 4 OVAL STEP BARS APPLICATION: 2011-2017 Jeep Grand Cherokee PART NUMBER: 23-3610, 23-3615, 21-3610, 21-3615, 23-73610 ITEM QUANTITY DESCRIPTION TOOLS NEEDED
More information10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2
PARTS LIST: 1 Driver/Left sidebar 4 12mm x 32mm OD x 3mm Flat Washer 1 Passenger/Right sidebar 4 12mm x 24mm OD x 2.5mm Flat Washer 1 Driver/Left Mounting Bracket 6 12mm Lock Washers 1 Passenger/Right
More informationDriver/Left Top. Support Bracket
PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 65" Plasma Screens. Models: PLAV70, PLAV70-S
Installation and ssembly - Universal rticulating Swivel Double-rm for 42" - 65" Plasma Screens Models: PLV70, PLV70-S Max UL Load apacity: 200 lb (91 kg) 2300 White Oak ircle urora, Il 60502 (800) 865-2112
More informationMedium Flat Panel Universal Interface Bracket (MSB-V)
INSTALLATION Medium Flat Panel Universal Interface Bracket () INSTRUCTIONS The interface bracket functions as the universal mounting solution for medium flat panel displays. The is compatible with a multitude
More information6 BAY AV CREDENZA WITH DUAL DISPLAY MOUNT
D2/367M2 SSEMLY INSTRUCTIONS 6 Y V CREDENZ WITH DUL DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationModel MSPPWRTW Large Flat Panel Single Arm Wall Mount
INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationLCD TV WALL MOUNT INSTALLATION INSTRUCTIONS. DUAL Swing Arm (RFWD-110) WARNING
INSTALLATION INSTRUCTIONS LCD TV WALL MOUNT DUAL Swing Arm (RFWD-110) WARNINGS WARNING WARNING CAUTION CAUTION The maximum weight to be installed on the RFWD wall mount is 40 lbs. (18.1 kg). The RFWD is
More informationLEG CURL IP-S1315 INSTALLATION INSTRUCTIONS
LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written
More information