MODEL N 1529 OWNER S MANUAL

Size: px

Start display at page:

Download "MODEL N 1529 OWNER S MANUAL"

Tiffany Jade White
5 years ago
Views:

1 MODEL N 1529 OWNER S MANUAL 1

2 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Most injuries are caused by misuse and/or not following instructions. Use caution when using this product. BEFORE BEGINNING ASSEMBLY 3

3 TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY 1/2 Wrench 7/16 Wrench 9/16 Wrench 3/4 Wrench 3/8 Wrench 3/16 Allen Wrench Phillips Screwdriver Rubber Mallet Pliers Funnel Water Hose Scrap Wood Sand *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the setup area until assembly is complete. 4

4 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.! Note: These areas are usually located in the bottom, right-hand corner of a step and indicate that damage to the product or serious injury may occur if the caution or warning is not heeded. CAUTION WARNING 5

5 PARTS LIST ID Item Description Qty HARDWARE LIST ID Item Description Qty BCO Pole Assembly Hardware BCQ Pole to Base Assembly Hardware 6

6 HARDWARE LIST ID Item Description Qty BCS Backboard to Rim Assembly Hardware BCR Backboard to Pole Assembly Hardware BCT Handle Assembly Hardware 7

7 Parts shown at 10% of Actual Size PARTS IDENTIFIER ALH 30 1/2 ALF 43 *Warning Sticker applied to side not shown ALE 43 ALB AKQ ALI AJK AJJ 15 3/4 AJC 17 AKC 7 AJE AKB 8

8 Parts shown at 10% of Actual Size PARTS IDENTIFIER ALX AKZ Parts shown at 5% of Actual Size AJI AJM Part shown at Actual Size AEF 9 AQG

9 Parts shown at 25% of Actual Size PARTS IDENTIFIER AKL AKN AMU AJY ALL AMN AOW AOX 10

10 POLE ASSEMBLY HARDWARE Hardware shown at Actual Size HARDWARE IDENTIFIER ABH AAF ADA ADS POLE TO BASE ASSEMBLY HARDWARE Hardware shown at Actual Size CIH ABB AAE BTS ABD ABN BZO AAO BACKBOARD TO RIM ASSEMBLY HARDWARE Hardware shown at Actual Size AAS ADQ ABS 11 AAV

11 HARDWARE IDENTIFIER BACKBOARD TO RIM ASSEMBLY HARDWARE (CONTINUED) Hardware shown at Actual Size ABI AAB AAJ ABD ABF ABK Hardware shown at 25% of Actual Size AJW AOU BACKBOARD TO POLE ASSEMBLY HARDWARE Hardware shown at Actual Size ABP ABL 6 5/8 AAX ADG 12

12 HANDLE ASSEMBLY HARDWARE Hardware shown at Actual Size HARDWARE IDENTIFIER AAL ADJ AAN AAM 6 1/2 ACZ ABA ABB 6 5/8 ADG AAX AQH ADR ADT 13

13 1 BCO POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABH ADA ADS Parts shown at 10% of Actual Size ABB PARTS REQUIRED AAF CIH Part shown at 25% of Actual Size ALH 30 1/2 ALL ALF 43 *Warning Sticker applied to side not shown ALE 43 TOOLS REQUIRED Phillips Screwdriver 9/16 Wrench 14 Scrap Wood

14 ADS CIH 1.1 Top Pole (ALH) Middle Pole (ALF) 1/4 x 3/4 Screw (ADS) Domed Countersink Washer (CIH) ALH ALH CIH ADS Warning Sticker ALF ALF! Note: The 1/4 x 3/4 Screw and Domed Countersink Washer should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 15

15 Scrap Wood NO HARDWARE REQUIRED FOR THIS PAGE 1.2 ATTENTION: THIS STEP CANNOT BE REVERSED! Top Pole (ALH) Middle Pole (ALF) ALH 6x ALF WARNING The Poles must be seated together! Even if the Poles cover the slots before seating, they must be struck on a hard surface fi ve to six times! Failure to seat the Poles correctly could allow the Poles to separate during use, which could lead to serious personal injuries or property damage.! Note: Do not hit your feet with the Pole sections, as serious injury could occur. 16

16 ADS CIH 1.3 Middle Pole (ALF) Bottom Pole (ALE) 1/4 x 3/4 Screw (ADS) Domed Countersink Washer (CIH) ALF ALF CIH ALE ADS ALE! Note: The 1/4 x 3/4 Screw and Domed Countersink Washer should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 17

17 9/16 ADA ABB ABH AAF 1.4 3/8 x 3 1/2 Hex Bolts (ABH) 3/8 Flat Washers (AAF) Middle Pole (ALF) 1/2 x 2.91 Spacers (ADA) Pole Bracket (ALL) ALF ABH AAF ALF ADA Small holes Large holes ALL ABB 18

18 Scrap Wood NO HARDWARE REQUIRED FOR THIS PAGE 1.5 ATTENTION: THIS STEP CANNOT BE REVERSED! Top and Middle Poles (ALH and ALF) Bottom Pole (ALE) DO NOT COMPLETE ASSEMBLY ALH ALF x6 ALE WARNING The Poles must be seated together! Even if the Poles cover the slots before seating, they must be struck on a hard surface fi ve to six times! Failure to seat the Poles correctly could allow the Poles to separate during use, which could lead to serious personal injuries or property damage.! Note: Do not hit your feet with the Pole sections, as serious injury could occur. 19

19 2 BCQ POLE TO BASE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size Bag BCQ AAE BTS ABD ABN BZO Part shown at 5% of Actual Size PARTS REQUIRED AAO Part shown at 25% of Actual Size AJM AMU Parts shown at 10% of Actual Size ALI AJC 15 3/4 7 AJE TOOLS REQUIRED 1/2" Wrench EEO-3/16 Allen Wrench 20

20 NO TOOLS REQUIRED FOR THIS PAGE AAE AAO ABD ABN 2.1 Pole Brace (ALI) Base (AJM) Only fi nger tighten the hardware for now. ALI Curved End! Straight End ABD AAO AAE ABD Note: Repeat this step to install the other Pole Brace to the other side of the Base. AJM 2.2 1/2 x 15 3/4 Axle (AJC) Wheels (AMU) Bottom Pole (ALE) 1/2 x 7 Axle (AJE) 1/2 x 1/8 Spacers (ABN) AMU AMU ALE AJE AJC ABN AJC ABN 21

21 3/16" 1/2" BZO BTS 2.3 Middle Pole (ALF) 1/2 x 15 3/4 Axle (AJC) Base (AJM) 1/2 x 7 Axle (AJE) AJM 2.4 AJC Pole Braces (ALI) Bottom Pole (ALE) tighten all Pole to Base assembly hardware AJE AJM BTS ALI ALI BZO ALE! Note: Tip the system forward so the Pole rests on the ground. Do not stand the system up until it is filled with either sand or water later in the assembly. 22

22 3 BCS BACKBOARD TO RIM ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size AAS ABI ADQ ABF ABD AAB AAV ABS ABK AAJ Hardware shown at 25% of Actual Size AJW BNP AOW 23

23 3 BACKBOARD TO RIM ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size AJJ ALX AJK Part shown at 5% of Actual Size AJI Part shown at 25% of Actual Size AOX TOOLS REQUIRED Pliers 1/2 Wrench 7/16 Wrench 24 3/8 Wrench

24 7/16 BNP AAS ABS AAB U-Bolt (BNP) Left and Right Backboard Brackets (AJJ & AJK) AJK AJK AJJ AJJ BNP Notch BNP 3.2 1/4 x 2 3/4 Hex Bolts (AAS) 1/2 x 2 5/16 Galvanized Spacers (ABS) 1/4 Centerlock Nuts (AAB) AAB ABS AAS AAS AAB! Note: Tighten the hardware securely now. 25

25 1/2 ABI AAJ ABD ABF 3.3 5/16 x 2 1/4 Tap Bolts (ABI) 5/16 Washers (ABD) 7/16 Rubber Washers (ABF) Rim (ALX) 5/16 Hex T-Nuts (AAJ) ALX ABI ABD ABF AAJ ALX ABI ABI! Note: Make sure that the 5/16 x 2 1/4 Tap Bolts are positioned on the outside edge of the holes as shown. AAJ AAJ ABF ABF! Incorrect Correct Note: Do not overtighten the hardware so that the 7/16 Rubber Washers bulge outward as shown. 26

26 1/2 AAV ABK AOX 3.4 Rim Support Channel (AOX) Backboard (AJI) 4.86 U-Bolt (BNP) AJI BNP AOX 3.5 Rim (ALX) Backboard (AJI) 5/16 Jam Nuts (AAV) 4.86 U-Bolt (BNP) 5/16 Nylock Flange Nuts (ABK) 5/16 x 2 1/4 Tap Bolts (ABI) ALX ABI AAV AAV BNP AJI ABK ABK 27

27 1/2 AOW AJW ABK 3.6 Compression Springs (AJW) 4.86 U-Bolt (BNP) Spring Retainer Plate (AOW) 5/16 Nylock Flange Nuts (ABK) Rim (ALX) ALX AOW AJW ABK BNP! Note: DO NOT COMPLETELY TIGHTEN THE 5/16 NYLOCK FLANGE NUTS IN THIS STEP! Only tighten the Nuts until the Rim does not wobble. Tightening the Nuts will adjust the Rim tension. 28

28 3/8 ADQ 3.7 Left and Right Backboard Brackets (AJJ & AJK) Backboard (AJI) ADQ ADQ AJJ AJK AJI 29

29 4 BACKBOARD TO POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABP ABL 6 5/8 AAX ADG Parts shown at 10% of Actual Size PARTS REQUIRED 17 AKC AKB Part shown at 25% of Actual Size AJY TOOLS REQUIRED 3/4 Wrench 7/16 Wrench 30 Rubber Mallet

30 7/16 NO HARDWARE REQUIRED FOR THIS PAGE 4.1 Counterbalance Spring (AJY) 1/2 x 2 5/16 Galvanized Spacer (ABS) ABS AJY! Note: It may be necessary to use a Rubber Mallet to snap the Counterbalance Spring into place. If the Rubber Mallet does not work, undo the hardware in the image that has been shaded gray. Slide the Counterbalance Spring over the Spacer after it has been detached. Then replace and re-secure the hardware. 31

31 3/4 ADG 6 5/8 ABL AAX 4.2 Short Extension Arms (AKC) AKC AKC AAX ABL ABL ADG AKC! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 32

32 6 5/8 3/4 ADG ABL AAX 4.3 Long Extension Arms (AKB) AAX AKB ABL ABL AKB ADG AKB! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 33

33 6 5/8 3/4 ADG 4.4 ABP AAX CAUTION: HAVE ONE ADULT HOLD THE BACKBOARD IN PLACE UNTIL ASSEMBLY HAS BEEN COMPLETED! Short and Long Extension Arms (AKC & AKB) AKC AKC AAX ADG ABP ABP AAX ADG AKB ABP ALH ABP AKB! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 34

34 5 HANDLE ASSEMBLY Hardware shown at Actual Size HARDWARE REQUIRED AAL ADJ AAN AAM ACZ 6 1/2 ABA ABB 6 5/8 ADG AAX AQH ADR ADT 35

35 5 HANDLE ASSEMBLY Parts shown at 10% of Actual Size PARTS REQUIRED ALB AKQ Parts shown at 25% of Actual Size AKL AKN AMN Parts shown at Actual Size AQG TOOLS REQUIRED Phillips Screwdriver 7/16 Wrench 1/2 Wrench 3/4 Wrench 9/16 Wrench 36

36 ADR 5.1 Lock Tab (AQG) Trigger (AMN) ADR ADR AQG! Note: Make sure the Lock Tab is oriented as shown when attaching the Tab to the Trigger. AMN 5.2 Right Handle (AKN) Outer Tube (ALB) ALB AKN! Note: Make sure that the Inner Channel (AKQ) has been removed from the Outer Tube before performing this step. 37

37 ADT AQH 5.3 Trigger Spring (AQH) Trigger (AMN) Right Handle (AKN) Lock Tab (AQG) Outer Tube (ALB) ALB AQG AMN AQH AKN! 5.4 Note: Pull the Trigger to ensure it moves correctly before attaching the Left Handle (AKL). Left Handle (AKL) Right Handle (AKN) Outer Tube (ALB) ALB ADT ADT ADT AKN ADT ADT AKL! Note: To prevent stripping the holes in the Handles, do not overtighten the #6 x 5/8 Screws (ADT). 38

38 7/16 AAL ADJ 5.5 1/4 x 1 1/4 Hex Bolt (AAL) Outer Tube (ALB) 1/4 Cap Nut (ADJ) ADJ AAL ALB WARNING 39

39 1/2 AAM AAN 5.6 Trigger (AMN) Inner Channel (AKQ) Outer Tube (ALB) ALB! Note: Ensure that the notches on the Inner Channel face the Handle as shown. AKQ 5.7 Inner Channel (AKQ) Pole Bracket (ALL) AAM ALL AAN WARNING 40

40 3/4 ADG 6 5/8 ACZ AAX 5.8 Outer Tube (ALB) Long Extension Arms (AKB) ADG AAX AKB ACZ ACZ AKB ALB! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 41

41 6 1/2 9/16 ABA ABB 5.9 3/8 x 6 1/2 Hex Bolt (ABA) Short Extension Arms (AKC) 3/8 Centerlock Nut (ABB) ABA AKC AKC ABB! Note: Tighten the 3/8 Centerlock Nut until it is flush with the end of the Bolt. 42

42 Wrench NO HARDWARE REQUIRED FOR THIS PAGE 5.10 Counterbalance Spring (AJY) 3/8 x 6 1/2 Hex Bolt (ABA) ABA AJY! Note: Make sure all hardware has been securely tightened before moving to the next section. 43

43 6 FINAL ASSEMBLY HARDWARE REQUIRED NO HARDWARE REQUIRED FOR THIS TION Parts shown at 10% of Actual Size PARTS REQUIRED AKZ Parts shown at Actual Size AEF TOOLS REQUIRED Funnel Sand Water Hose 44

44 NO HARDWARE REQUIRED FOR THIS PAGE Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.1 OPTION A: FILLING WITH SAND Base Plug (AEF) Base (AJM) WARNING For safety reasons, we recommend that sand be used instead of water to fill the Base. If a leak develops, water could run out unnoticed, allowing the system to fall over, resulting in serious personal injuries, or property damage. If using Water, check the Base carefully for leaks. If a leak is found, lay the system down on the ground and call Customer Service. Do not use, stand up, or play on a leaking system. AEF AJM 45

45 NO HARDWARE REQUIRED FOR THIS PAGE Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.1 OPTION B: FILLING WITH WATER Base Plug (AEF) Base (AJM) AEF AJM 46

46 NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE 6.2 Net (AKZ) Rim (ALX) ALX AKZ! 6.3 Note: If a replacement Net is needed, please call our Customer Service Department. Our Nets are shorter than average to reduce the risk of entanglement. Height Sticker (AKP) Left Handle (AKL) AKP AKL 47

47 OPERATION OF HEIGHT ADJUSTMENT SYSTEM ONLY ADULTS SHOULD ADJUST THE HEIGHT OF THE SYSTEM. MOVING THE SYSTEM WARNING: CAUTION: POLE CARE AND SYSTEM MAINTENANCE IF RUST HAS PENETRATED THROUGH THE POLE ANYWHERE, REPLACE IT IMMEDIATELY! 48

48 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 51

49 WARRANTY INFORMATION LIFETIME BASKETBALL EQUIPMENT 5-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. Discover other sports equipment on our website.

MODEL N COPY OWNER S MANUAL. Keep this Product ID Number and use when contacting Customer Service:

MODEL N COPY OWNER S MANUAL. Keep this Product ID Number and use when contacting Customer Service: MODEL N 51550 OWNER S MANUAL COPY Keep this Product ID Number and use when contacting Customer Service: 1 REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefi ts to registering your Lifetime product.