How To Make An Artificial Deckle Edge using the Dual Edge Ripper

Transcription

1 How To Make An Artificial Deckle Edge using the Dual Edge Ripper Artists love the look of a deckle edge. Hand made papers can be made with deckled edges on all four sides, but mould made papers can only be made with two true deckle edges (see definition below). Although many fine art ink jet papers are mould made (the closest machine process to hand made), the final ink jet receptive coating process eliminates the manufacturerʼs ability to retain or offer a true deckled edge on his finished product. Paper Glossary: Deckle Edge : The feathery edge which is the result of the natural run-off of wet pulp when making handmade and mould made paper, or the result of sheets being torn when wet. The edge is simulated in machine made papers by cutting them with a stream of water when still wet. Artists often try to create an artificial deckle edge by hand tearing the edges of the paper, but this can be very hit and miss, often resulting in a ruined print. Using a steel ruler to guide oneʼs tearing or ripping is better, but often the edges produced have little character and are too uniform or straight with some papers. Digital artists have also tried to put in the look of a torn or deckled edge, by artificially painting the edges with various filters or Photoshop techniques: Deckled Edges in Photoshop Torn Paper technique These digital effects are quite impressive and realistic. However, these digital methods pale in the perceived value customers give to an actual torn or deckle edge, because it appears to be hand made by the artist. But until the invention of the Dual Edge Ripper there was never a fast and easy way of producing a consistently good torn or deckled edge.

2 Making a deckle edge the Ripper way.. 1. The Standard Dual Edge Ripper is made of clear Lucite, and is 24 inches long and 4 inches wide. 2. The Scrap Book Dual Edge Ripper is made of clear Lucite, and is 12 inches long and 4 inches wide. Fine Teeth Course Teeth 3. The Lucite strip has two uniquely cut ragged edges. One side has fine teeth, and the other side has course teeth.

3 4. These teeth are cut on a bevel angle in order to tear paper in a unique way. 5. The ripper is placed over the paper and the edge of the paper is pulled up toward you. Notice in this view print is face up. Face up gives a white reveal. 6. Use a table with a square edge keeping ripper parallel and even to edge of table, allowing the part of the print to be torn off to exceed past the edge of the table. Notice in this view print is face down. Face down gives no reveal.

4 7. Here is a close up of creating a unique rip that simulates a deckle edge. This sample has utilized the course edge of the ripper and has been done on a photo print. Notice that the right to left edge shows a white reveal (tearing with image facing up), the up and down edge shows no reveal (tearing with image facing down). 8. If your print is wider or longer than 24, just move the ripper and continue ripping.

5 9. Hereʼs a deckle edge border, using the smooth or fine teeth side of the ripper. All four borders were deckled (only two sides are shown in this photo) AFTER the paper had been printed with an image (itʼs much easier to feed the paper into the printer that way). TIP: If you want to have a 1 inch border with a deckled edge around your image, youʼll need to leave at least 2 inches of border around the image, because youʼll want at least an inch of paper to hold onto when you do your ripping 10. Hereʼs a view of the deckle edged print that has been matted and framed. TIP: Mount the print to a sheet of 4 ply mat board that is about 1/4 smaller than the deckle edged print, then mount that mat board to the mounting board that goes into the frame behind the glass and beveled mats (double matting is necessary to give the depth youʼll need to for this technique). The mat behind the print act as a pedestal, raising the print enough to create a nice drop shadow, and producing a very artistic and three-dimensional quality to your displayed art.

6 11. Torn Edges with a White Reveal: The Dual Edge Ripper is featured in Epsonʼs Finishing Touches DVD. Randy Hufford demonstrates in this video clip how you can also use the Dual Edge Ripper to quickly produce torn edges with and without a white reveal, that gives a perceived value to your clients --even on inexpensive photo papers (you donʼt have to use a fine art paper for this effect)! This quick presentation technique will offer a great add-on sale (a lower-priced item for every budget) for your gallery. Download sample movie from this section: or you can order the Epson Finishing Solutions DVD from us. Download Quicktime MPEG-4 Movie: 2.6MB - Requires Quicktime 6 Download Windows Media Video: 2.4MB - Requires Media Player 9 The Dual Edge Ripper has many options. Besides having two different teeth sizes, the ripper can be used not only to simulate a deckle edge around the border of a print, but it can be use to tear along the edge of the printʼs image, creating a very artistic effect for some subjects. This effect can also be varied depending on whether the printʼs image faces down or up when it is being ripped. Be sure to experiment to determine the deckle or rip effect you like best before proceeding to an important print.