V Ball Control Valve Product Range

Transcription

1 V all ontrol Valve Product ange VSI all Valve Product ange...v, 6...V Type Suitable ctuators v Inches DN [mm] -way NPT Flange Spring eturn Electronic Fail-Safe Non-Spring eturn V ½ 40 50V V V V-350 NF Series F Series GK Series M Series GM Series SY Series pplications ater-side control of air handling apparatus in ventilation and air-conditioning systems ater/steam control in heating systems Mode of Operation The control valve is operated by an electronic actuator that responds to a standard voltage for on/off control, by a proportional VD/4 0 m, or 3-point control system. The actuator will then move the ball of the valve to the position dictated by the contol signal thus change the fl ow V-507 Product Features Equal percentage of fl ow 300:1 rangeability NSI Leakage lass IV ctuator Specifications ontrol type Manual override Electrical connection On/Off, Floating Point, Proportional, -10 VD Multi-Function Technology (MFT) GM, M, SY, NF, F, GK 3 ft [1m] cable with ½ conduit fi tting Valve Specifications Service Flow characteristic chilled or hot water, (60% glycol) steam equal percentage Sizes 1 to 6 Type of end fi tting NPT (1 to ) fl anged (3 to 6 ) Materials ody Stem all Seats Packing Pressure rating Media temp range 400 F carbon steel stainless steel chrome plate stainless steel tefl on spring loaded tefl on Up to 400 psig Maximum inlet pressure Steam Maximum ΔP steam Maximum ΔP water 50 psi 100 psi 150 psi

2 General Information, Flow Pattern, Operation and Installation "V" all Valves GENEL INFOMTION arbon Steel or Stainless Steel 150/300 NSI ated odies Equal Percentage Flow haracteristic Dual ody rating on 1, 1½ & (NSI 150/300) SME Face to Face Dimensions NSI lass IV Shut-off 50PSI 400 degree rated Field replaceable seat Maintenance free spring loaded packing NOTE: Industrial ball valves have serviceable components similar to globe valves, proper maintenance of these parts will ensure longer in service life for the valves. The seats of these valves will require replacement at an interval consistent with the number of full cycles the valve has been operated, or as field condition dictates. Ideal for replacing globe valves where high close off is required. FLO PTTEN VS SEIES LL VLVE PIPING DIGMS ater pplication Steam pplication PIPING/MOUNTING OIENTTION ssembly can be mounted horizontally or vertically for water applications. For steam applications the valve can be mounted vertically but if mounted horizontally the valve must be 90 off center of the pipe. Do not install with actuator below pipe. P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

3 Piping Sizing Geometry "V" all Valves Valve Size v Type Model # 1 Fp v 1¼ Fp v 1½ Fp v Size 3 Fp v 1 4 -ay NPT 00V ½ 55 -ay NPT 50VD ay NPT 00V ay Flanged 6300V ay Flanged 6400V ay Flanged 6600V Fp v ½ Fp v 4 Fp v 5 Fp v 6 Fp v 8 Fp v 10 Fp v P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI 3

4 iring Instructions "V" all Valves GENEL IING INSTUTIONS NING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with flexible conduit. lways read the controller manufacturer s installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) Typically actuators require a 4 V class transformer and draw a maximum of 10 V per actuator. The actuator enclosure cannot be opened in the fi eld, there are no parts or components to be replaced or repaired. EM directive: 89/336/EE Software class : Mode of operation type 1 Low voltage directive: 73//EE Typical transformer sizing ctuator Series Voltage Max. V Per ctuator F 4 10 GK 4 0 NF 4 10 LF 4 6 GM 4 7 M 4 6 NM 4 4 LM 4 3 UTION It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectification. Some controllers use full wave rectification. hen these two different types of power supplies are connected to the same power transformer and the D commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed: 1. The TOTL current draw of the actuators (V rating) is less than or equal to the rating of the transformer.. Polarity on the secondary of the transformer is strictly followed. This means that all No. 1 wires from all actuators are connected to the common leg on the transformer and all No. wires from all actuators are connected to the hotleg. Mixing wire No. 1 & on one leg of the transformer will result in erratic operation or failure of the actuator and/or controls. Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed: 1. The transformers are properly sized.. ll No. 1 wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. ire Type and ire Installation Tips For most installations, 18 or 16 Ga. cable works well with elimo actuators. Use code-approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire-tie the splice to reduce the possibility of the splice being inadvertently pulled apart. ire length for actuator installation Keep power wire runs below the lengths listed in the following tables. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. See section 1 for specifi c transformer sizing information for the actuator selected. Example: 3 actuators, 16 Ga wire 350 Ft 3 ctuators = 117 Ft. Maximum wire run P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

5 Nomenclature "V" all Valves 100 V -04 MX 4 -MFTX1 Valve = -way NPT 6 = -way Flanged Valve Size 5-50 = 1 to = 3 to 6 Flanged Industrial onstruction/ Material V = hrome plated stainless steel V ball v ctuator Type Power Non-Spring eturn Supply M 4 = 4 V/D GM 10 = 10 V SY 0 = 0 V SY P Mechanical Fail-Safe NF F Electronic Fail-Safe GK... ontrol -3-X1 = On/Off, Floating Point -MFTX1 = Multi-Function Technology -MFT95 = Ω -S = uilt-in uxiliary Switch ODEING EXMPLE 3 For MFT orders only - select programming code 1 hoose the valve actuator combination. 00V-04+MX4-MFT-X1 +NO +Tagging (if needed) Specify preference or confi guration. Set-Up 4 Does order require tagging? P /13 - Subject to change. elimo ircontrols (US), Inc. Non-Spring Models NO = Normally Open N = Normally losed Spring eturn Models NO/FO = Normally Open/Fail Open NO/F = Normally Open/Fail losed N/FO = Normally losed/fail Open N/F = Normally losed/fail losed efers to valve ports to. P (01) P-100xx (xx) P-00xx (xx) P-300xx (Fxx) P-400xx (Jxx) X-XXXXX X-XXXXX ontrol voltage applications Pulse width modulation applications Floating Point applications On/Off applications reate custom MFT confi guration code reate custom MFT confi guration in the fi eld with MFT-actuator P software 5 omplete Ordering Example: 00V-04+MX4-MFT-X1+NO+01 Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) Example: HU-1 FU- Part number for tagging: US ND LTIN MEI 5

6 ...V Series, -ay, Vall ontrol Valve ast Iron ody, Hardened hrome Plated, Stainless Steel all and Stem Fast quarter turn open or closed operation Stainless steel ball and stem Positive shut-off Two-piece body construction pplication ater-side control of air handling apparatus in ventilation and air-conditioning system ater/steam control in heating systems 300:1 rangeability The dimensions and drilling of end fl anges conform to the merican cast iron fl ange standard, lass 150 (NSI 16.1). Valve Nominal Size Type Suitable ctuators v Inches DN [mm] -way NPT Spring Non-Spring Technical Data Service chilled or hot water, 60% glycol V ½ 40 50V V-077 NF Series F M Series SY Series Flow characteristic equal percentage ction 90% rotation valve open, valve closed Sizes 1,1½, Type of end fi ttings NPT Materials: ody arbon Steel all Stainless Steel with Hardened hrome Plating Seats Tefl on Stem Stainless Steel Packing Spring-loaded Tefl on Pressure rating NSI 300 Media temp. range - F to +380 F (-30 to +193 ) lose-off pressure steam: 00 psi water: 150 psi Maximum differential pressure (ΔP) steam: 100psi water: 150psi P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI 6

7 6...V Series, -ay, Vall ontrol Valve ast Iron ody, Hardened hrome Plated, Stainless Steel all and Stem Fast quarter turn open or closed operation Stainless steel ball and stem Positive shut-off Two-piece body construction pplication ater-side control of air handling apparatus in ventilation and air-conditioning system ater/steam control in heating systems 300:1 rangeability The dimensions and drilling of end fl anges conform to the merican cast iron fl ange standard, lass 150 (NSI 16.1). Technical Data Media Flow characteristic ction Sizes 3,4,6 Type of end fi ttings fl anged chilled or hot water, 60% glycol equal percentage 90% rotation valve open, valve closed v Valve Nominal Size Type Suitable ctuators Inches DN Electronic Non- [mm] -way NPT Spring Fail-Safe Spring V V V-507 F GK M Series GM SY Series Materials: ody all Seats Stem Packing arbon Steel Stainless Steel with Hardened hrome Plating Tefl on Stainless Steel Spring-loaded Tefl on P /13 - Subject to change. elimo ircontrols (US), Inc. Pressure rating NSI 150 Media temp. range - F to +380 F (-30 to +193 ) lose-off pressure steam: 00 psi water: 150 psi Maximum differential pressure (ΔP) steam: 100psi water: 150psi US ND LTIN MEI 7

8 M(X)4-3-X1 On/Off, Floating Point Dimensions with -ay Valve H Technical Data ontrol Power supply M(X)4-3-X1 on/off, fl oating point 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption running.5 holding 0. Transformer sizing 5.5 V (class power source) Electrical connection M4-3-X1 Overload protection Input impedance ngle of rotation Torque Direction of rotation Position indication Manual override unning time ½ conduit connector 3 ft, 18 G plenum rated cable electronic throughout 0 to 95 rotation 600 Ω max 95, adjustable with mechanical stop 180 in-lb [0 Nm] reversible with refl ective visual indicator (snap-on) external push button 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to 1 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM type /IP54 Housing material UL94-5V gency listings culus according to UL /--14, N/S. No. 4 certifi ed, E according to 73//EE Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ V V P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

9 M(X)4-3-X1 On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. 5 Only connect common to neg. ( ) leg of control circuits. MX4-3-X1 On/Off control Meets culus or UL and S requirements without the need of an electrical ground connection P /13 - Subject to change. elimo ircontrols (US), Inc. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. MX4-3-X1 Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 1 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction US ND LTIN MEI 9

10 MX4-MFT-X1 Multi-Function Technology Dimensions with -ay Valve H Technical Data Power supply MX4-MFT-X1, MX4-MFT95-X1 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption 4 (1.5 ) Transformer sizing 6 V (class power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for to 10 VD (0.1 m) 500 Ω for 4 to 0 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback to 10 VD, 0.5 m max VD variable ngle of rotation max 95, adjustable with mechanical stop electronically variable Torque 180 in-lb [0 Nm] Direction of rotation reversible with Position indication refl ective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) variable (90 to 350 seconds) Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to 1 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM type /IP54 Housing material UL94-5V gency listings culus according to UL /--14, N/S E , S. No. 4-93, E according to 89/336/EE Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ V V P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

11 MX4-MFT-X1 Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 4 VD. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 4 V line. 6 ZG-01 may be used. 7 8 ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. On/Off control V/D Transformer Position ( ) Feedback VD (+) 4 V Transformer a lk (1) ommon ed () Hot ht (3) Y Input Org (5) U Output MFT lk (1) ommon ed () Hot Meets culus or UL and S requirements without the need of an electrical ground connection. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point 3 5 to 10 VD Feedback Signal 4 V Transformer 1 3 ontrol Signal 4 to 0 m or to 10 VD ( ) (+) Ω 500Ω 1/4 watt ht (3) Y 1 Input 8 Pnk (4) Y Input Org (5) U Output to 10V MFT lk (1) ommon ed () + Hot ht (3) Y 1 Input, to 10V Org (5) U Output, to 10V 399 MFT VD/4-0 m P /13 - Subject to change. elimo ircontrols (US), Inc. PM 1 4 V Transformer ( only) Position Feedback VD ( ) (+) 5 lk (1) ommon ed () + Hot ht (3) Y Input Org (5) U Output MFT US ND LTIN MEI 11

12 Multi-Function Technology 4 5 Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. onsult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper losed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. 4 V Transformer Low Limit ontrol 4 V Transformer Series 90 ontroller 135 ontroller 4 V Transformer Series 90 low limit control 135 for 0 to 50% control 80 for 0 to 100% control lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD High Limit ontrol 4 V Transformer Series 90 ontroller Series 90 high limit control V Transformer 4 lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller Shunting esistor Series 90 ontroller No. of actuators esistance esistor Kit No. ZG-03 To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller using a Minimum Position Potentiometer 4 V Transformer Series 90 ontroller Shunting esistor 4 H05 hangeover ontroller Occupied ontact To other actuators S963 Minimum Position Potentiometer lk (1) ommon ed () + Hot 5 ht (3) ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 4 H05 hangeover ontroller Shunting esistor 4 V Transformer No. of actuators esistance esistor Kit No. ZG , 7100 ontroller Shunting esistor Y 973, 7100 T775 Q09 Minimum Position Potentiometer To other actuators To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Occupied ontact Honeywell T675 Morning armup lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Used with the 973 and 7100 controllers 4 V Transformer Honeywell T675 Morning armup Honeywell Q09 Minimum Position Potentiometer lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot 00 ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

13 GM4-3-X1 On/Off, Floating Point Dimensions with -ay Valve H P /13 - Subject to change. elimo ircontrols (US), Inc. Technical Data ontrol Power supply Power consumption Transformer sizing Electrical connection Overload protection GM4-3-X1 on/off, fl oating point 4 V ± 0% 50/60 Hz 4 VD ± 10% running 4 holding 6 V (class power source) 3 ft [1m] 18 G plenum rated cable ½ conduit connector electronic throughout stroke ngle of rotation 95 Direction of rotation reversible with switch Position indication refl ective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature - F to 1 F [-30 to 50 ] Housing NEM /IP54 with cable entry down Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /--14, N/S E , S. No. 4-93, E according to 89/336/EE Noise level <45 d() Quality standard ISO 9001 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6400V US ND LTIN MEI 13

14 GM4-3-X1 On/Off, Floating Point iring Diagrams 1 Provide overload protection and disconnect as required. ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. Position feedback cannot be used with Triac sink controller. 4 The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) 5 or the ommon (sink) 4 V line. ontact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. On/Off control GM4-3-X1 Meets culus or UL and S requirements without the need of an electrical ground connection. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point or On/Off control GM4-3-X1 Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 1 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

15 GM4-S-X1 Proportional, 4V,..10 VD or 4..0m Dimensions with -ay Valve P /13 - Subject to change. elimo ircontrols (US), Inc. H Technical Data GM4-S-X1 Power supply 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption 4.5 () Transformer sizing 6.5 V (class power source) Electrical connection 18 G plenum rated cable ½ conduit connector protected NEM (IP54) 3 ft Overload protection electronic throughout 0 to 95 rotation Operating range Y to 10 VD, 4 to 0 m Input impedance 100 k (0.1 m), 500 Feedback output U to 10 VD (max 0.5 m) ngle of rotation max. 95, adjustable with mechanical stop Torque 360 in-lb [40 Nm] Direction of rotation reversible with switch actuator will move: = with decreasing control signal (10 to V) = with decreasing control signal (10 to V) Position indication refl ective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to 1 F [-30 to 50 ] Housing NEM, IP54, UL enclosure type Housing material UL94-5V gency listings culus acc. to UL /--14, N/S E :0, E acc. to 004/108/EE and 006/95/E Noise level <45d() Servicing maintenance free Quality standard ISO 9001 eight 3.4 lbs [1.55 kg] ated Impulse Voltage 800V, Type of action 1, ontrol Pollution Degree 3. Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6400V US ND LTIN MEI 15

16 GM4-S-X1 Proportional, 4V,..10 VD or 4..0m iring Diagrams 53_08 1 Provide overload protection and disconnect as required. UTION Equipment Damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. 5 Only connect common to neg. ( ) leg of control circuits. GM...4-S-X1 to 10 VD control Meets UL requirements without the need of an electrical ground connection. The ZG Ω resistor converts the 4 to 0 m control signal to to 10 VD, up to actuators may be connected in parallel. 53_08 NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. P /13 - Subject to change. elimo ircontrols (US), Inc. GM...4-S-X1 4 to 0 m control US ND LTIN MEI

17 GMX4-MFTX1 Multi-Function Technology Dimensions with -ay Valve PGE H P /13 - Subject to change. elimo ircontrols (US), Inc. Technical Data GMX4-MFTX1 GMX4-MFT95 ontrol fl oating point, PM, VD range, on/off Power supply 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption running 4.5 holding 3 Transformer sizing 7 V (class power source) Electrical connection 3 ft [1m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout stroke Input impedance 100k Ω for to 10 VD (0.1 m) 500 Ω for 4 to 0 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback to 10 VD, 0.5 m max VD variable ngle of rotation 95 Direction of rotation reversible with switch Position indication refl ective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature - F to 1 F [-30 to 50 ] Housing NEM /IP54 with cable entry down Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /--14, N/S E , S. No. 4-93, E according to 89/336/EE Noise level <45 d() Quality standard ISO 9001 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6400V US ND LTIN MEI 17

18 GMX4-MFTX1 Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. Position feedback cannot be used with Triac sink controller. 4 The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) 5 or the ommon (sink) 4 V line. On/Off control V/D Transformer Position ( ) Feedback VD (+) a lk (1) ommon ed () Hot ht (3) Y Input Org (5) U Output MFT ZG-01 may be used. ontact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller V Transformer 5 to 10 VD Feedback Signal 7 4 lk (1) ommon ed () Hot + ht (3) Y 1 Input 8 Pnk (4) Y Input Org (5) U Output to 10V 399 MFT Floating Point 4 V Transformer 1 3 ontrol Signal 4 to 0 m or to 10 VD ( ) (+) Ω 500Ω 1/4 watt 6 lk (1) ommon ed () + Hot ht (3) Y 1 Input, to 10V Org (5) U Output, to 10V 399 MFT VD/4-0 m PM 1 4 V Transformer ( only) Position Feedback VD ( ) (+) 5 lk (1) ommon ed () + Hot ht (3) Y Input Org (5) U Output MFT 399 P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

19 Multi-Function Technology P /13 - Subject to change. elimo ircontrols (US), Inc. 4 5 Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. onsult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper losed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. 4 V Transformer Low Limit ontrol 4 V Transformer Series 90 ontroller 135 ontroller 4 V Transformer Series 90 low limit control 135 for 0 to 50% control 80 for 0 to 100% control lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD High Limit ontrol 4 V Transformer Series 90 ontroller Series 90 high limit control V Transformer 4 lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller Shunting esistor Series 90 ontroller No. of actuators esistance esistor Kit No. ZG-03 To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller using a Minimum Position Potentiometer 4 V Transformer Series 90 ontroller Shunting esistor 4 H05 hangeover ontroller Occupied ontact To other actuators S963 Minimum Position Potentiometer lk (1) ommon ed () + Hot 5 ht (3) ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 4 H05 hangeover ontroller Shunting esistor 4 V Transformer No. of actuators esistance esistor Kit No. ZG , 7100 ontroller Shunting esistor Y 973, 7100 T775 Q09 Minimum Position Potentiometer To other actuators To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Occupied ontact Honeywell T675 Morning armup lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Used with the 973 and 7100 controllers 4 V Transformer Honeywell T675 Morning armup Honeywell Q09 Minimum Position Potentiometer lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot 00 ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury US ND LTIN MEI 19

20 SY...4 NEM 4X Industrial Style ctuators 4V ttention SY Series actuators are fractional horsepower devices, and utilize full-wave power supplies. Observe wire sizing and transformer sizing requirements. Proportional models NNOT be connected to elimo direct coupled (F, M, GM etc) actuator power supplies or any type of half-wave device. You MUST use a separate, dedicated transformer or power supply to power the SY actuator. Please do not connect other automation equipment to the dedicated SY supply source. You MUST use four wires (plus a ground) to control a proportional control SY actuator (See SY iring Section). See page 6 for dimensions Technical Data Power supply Electrical connection Overload protection Motor protection Geartrain Operating range SY...-4 SY...-4MFT SY1-4(P), SY-4MFT 4 V 50/60Hz, single phase ½ conduit connector, screw terminals thermally protected 135 cut-out SY1 H class insulation SY F class insulation high alloy steel gear sets, self locking on/off -10 VD, 4-0m, 1-5 VD Sensitivity SY...-4MFT 0.m / 100mV Feedback SY...-4MFT -10 VD, 4-0m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches () SPDT, V factory set for 3 and 87 change of state mbient temperature - F to 150 F [-30 to 65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, E, csus Power onsumption SY1-4(P) 1.8 SY-4MFT 3.0 Torque SY1-4(P) 35 Nm / 310 in-lb SY-4MFT 90 Nm / 801 in-lb Manual Override SY1-4(P) 8mm wrench SY-4 hand wheel unning Time SY1-4(P) 15 seconds SY-4MFT 15 seconds P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

21 SY...4 NEM 4X Industrial Style ctuators 4V iring Diagrams T 1 Transformer sizing = SY actuator draw X 1.5 (safety margin) EXMPLE: SY-4 requires 3.0 x 1.5 = 3.75, 3.75 X 4 V = 90V Transformer. There can be no connection (internal to automation controller, external wiring, or otherwise) between actuator supply neutral & control signal reference. These actuators are full wave devices. ny connection to half wave equipment will result in equipment damage. Do not change sensitivity or dip switch settings with power applied. 3 Terminals 6 & 11 can be common when control and feedback signals are both set for -10VD operation. 4 Use of feedback is optional. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control for SY(-5)-4 P /13 - Subject to change. elimo ircontrols (US), Inc. to 10 vdc or 4 to 0 m control signal for SY1-4P US ND LTIN MEI

22 SY...10 NEM 4X Industrial Style ctuators 10V pplication The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on the HSU and HS butterfl y valve series, these actuators are available for on/off and modulating applications. Depending on the application, they are available in 4 V, 10 V and 0 V. See page 6 for dimensions Technical Data Power supply Electrical connection Overload protection Motor protection SY Geartrain Operating range SY SY...-10MFT SY1-110(P), SY-10MFT 10 V 50/60Hz, single phase ½ conduit connector, screw terminals thermally protected 135 cut-out SY1 H class insulation F class insulation high alloy steel gear sets, self locking on/off, fl oating point -10 VD 4-0m, 1-5vdc Sensitivity SY...-10MFT 0.m / 100mV Feedback SY...10MFT -10 VD, 4-0m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches () SPDT, 5 50V factory set for 5 and 85 change of state mbient temperature - F to 150 F [-30 to 65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, E, csus Power onsumption SY1-110(P) 0.5 SY-10MFT 1.0 Torque SY1-110(P) 35 Nm / 310 in-lb SY-10MFT 90 Nm / 801 in-lb Manual Override SY1-110(P) 8mm wrench SY-10MFT SY8-10MFT hand wheel unning Time 50hz 60hz SY1-110(P) 13 seconds 1 seconds SY-10MFT 17 seconds 15 seconds P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

23 SY...10 NEM 4X Industrial Style ctuators 10V iring Diagrams arnings and autions appear at appropriate sections throughout this manual. ead these carefully. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. aution: Power supply voltage. with power applied. aution: Power supply voltage. 10 V N L1 H L G 35 Feedback () 36 G Ground ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 1 Feedback (+) E F LS3 - (Open Indication) ontact ating: 5 15 V Max V Max. LS4 -E (losed Indication) SY1-110P Observe class 1 and class wiring restrictions. G G Ground ctuator 4 Power Supply om ontrol Signal 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 35 ecommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator Internal Use Only 9 Internal Use Only 10 Internal Use Only 36 Use of feedback is optional. Power Supply om 10v (N) Power Supply Hot 10v (H) Feedback () Feedback (-) 1 Feedback (+) LS3 P /13 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal Feedback 36 Feedback 36 G G ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE PE Y 1 U5 1 ctuator Y 1 U5 1 ctuator P Tool Service Jack P Tool Service Jack N daption SYx-10S/MFT N daption SYx-10MFT L L Internal Use Only Internal Use Only 1 Internal Use Only Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y 10 Internal Use Only Power Supply om 10v (N) Power Supply Hot 10v (H) Internal Use Only Internal Use Only 1 Internal Use Only Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y 10 Internal Use Only LS3 - (Open Indication) D LS4 E D-F (losed Indication) F ontact ating: 5 50 V Max. SY...10MFT E F - (Open Indication) ontact ating: 5 15 V Max V Max. LS4 -E (losed Indication) SY1-110P US ND LTIN MEI

24 SY...0 NEM 4X Industrial Style ctuators 0V ttention SY Series actuators are fractional horsepower devices, and utilize full-wave power supplies. Observe wire sizing and transformer sizing requirements. Proportional models NNOT be connected to elimo direct coupled (F, M, GM etc) actuator power supplies or any type of half-wave device. You MUST use a separate, dedicated transformer or power supply to power the SY actuator. Please do not connect other automation equipment to the dedicated SY supply source. You MUST use four wires (plus a ground) to control a proportional control SY actuator (See SY iring Section). See page 6 for dimensions Technical Data Power supply Electrical connection Overload protection Motor protection Geartrain Operating range SY...-0 SY...-0MFT SY1-0(P), SY-0MFT 0 V 50/60Hz, single phase ½ conduit connector, screw terminals thermally protected 135 cut-out SY1 H class insulation SY F class insulation high alloy steel gear sets, self locking on/off, fl oating point -10 VD, 4-0m, 1-5vdc Sensitivity SY...-0MFT 0.m / 00mV Feedback SY...-0MFT -10 VD, 4-0m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches () SPDT, 5 50V factory set for 5 and 85 change of state mbient temperature - F to 150 F [-30 to 65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, E, csus Power consumption SY1-0(P) 0.3 SY-0MFT 0.5 Torque SY1-0(P) 35 Nm / 310 in-lb SY-0MFT 90 Nm / 801 in-lb Manual Override SY1-0(P) 8mm wrench SY-0MFT hand wheel unning Time 50hz 60hz SY1-0(P) 13 seconds 1 seconds SY-0MFT 17 seconds 15 seconds P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

25 SY...0 NEM 4X Industrial Style ctuators 0V iring Diagrams arnings and autions appear at appropriate sections throughout this manual. ead these carefully. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. aution: Power supply voltage. with power applied. aution: Power supply voltage. 0 V N L1 H L G 35 Feedback () 36 ctuator G Ground 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 1 Feedback (+) E F LS3 - (Open Indication) ontact ating: 5 15 V Max V Max. LS4 -E (losed Indication) SY1-0P Observe class 1 and class wiring restrictions. G G Ground ctuator 4 Power Supply om ontrol Signal 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) ecommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Power Supply om 0v (L1) Power Supply Hot 0v (L) 35 Feedback () 36 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 1 Feedback (+) LS3 P /13 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal Feedback 36 Feedback 36 G G ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE PE Y 1 U5 1 ctuator Y 1 U5 1 ctuator P Tool Service Jack P Tool Service Jack daption SYx-0MFT daption SYx-0MFT N N L L Internal Use Only Internal Use Only 1 Internal Use Only Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y 10 Internal Use Only Power Supply om 0v (L1) Power Supply Hot 0v (L) Internal Use Only Internal Use Only 1 Internal Use Only Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y 10 Internal Use Only LS3 - (Open Indication) D LS4 E D-F (losed Indication) F ontact ating: 5 50 V Max. SY...0MFT E F - (Open Indication) ontact ating: 5 15 V Max V Max. LS4 -E (losed Indication) SY1-0P US ND LTIN MEI 5

26 all Valve Dimensions with SY... Series ctuators Dimensions with -ay Valves Dimensions with Flanged Valves H H SY1 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ V SY1 Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6300V Dimensions with -ay Valves Dimensions with Flanged Valves H H P /13 - Subject to change. elimo ircontrols (US), Inc. SY Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ V SY Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6300V V V US ND LTIN MEI

27 NF ctuators On/Off Dimensions with -ay Valve H Models NF4-X1 NFUP-S-X1 NFUP-X1 w/built-in ux. Switch P /13 - Subject to change. elimo ircontrols (US), Inc. Technical Data ontrol on/off Power consumption NF4-X1 running 6 holding.5 NFUP(-S)-X1 running 6 holding.5 Transformer sizing NF4-X1 8.5 V NFUP(-S)-X1 9.5 V Electrical connection ½ conduit connector (-S model has cables) 3 ft [1m], 18 G appliance cables Electrical protection 10 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator unning time control <75 seconds spring <0 seconds mbient temperature - F to 1 F [-30 to 50 ] Housing NEM / IP54 gency listings UL 873, S. No. 4 certifi ed, E Noise level max. 45 d() NFUP-S-X1 uxiliary switch x SPDT, 3 (0.5 50V Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ US ND LTIN MEI 7

28 NF ctuators On/Off iring Diagrams 1 Provide overload protection and disconnect as required. UTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 4V actuators can be powered by 4 V/D. 4 For end position indication, interlock control, fan startup, etc., (-S) Models: SPDT, 3 (0.5 one switch fi xed at 10, one adjustable 10 to V Transformer 1 ommon + Hot 3 NF4-X1 On/Off iring for 4 V/D 194_NF 003-NFUP Meets culus or UL and S requirements without the need of an electrical ground connection. NFUP-X1 NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for 10 V S1 S S3 N NO 5 to 85 1 P /13 - Subject to change. elimo ircontrols (US), Inc. 4NFUP NFUP-S-X1 uxiliary Switch US ND LTIN MEI

29 NF ctuators Multi-Function Technology Dimensions with -ay Valve H Models NF4-MFT US P /13 - Subject to change. elimo ircontrols (US), Inc. Technical Data ontrol MFT ontrol signal to 10 VD, (4 to 0 m with 500 resistor) Power supply 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption running 6.5 holding 3 Transformer sizing 9 V, class power Electrical connection ½ conduit connector 3 ft [1m], 18 G appliance cable Overload protection electronic throughout rotation Feedback output variable D ngle of rotation 95, adjustable 35 to 95 (mechanically with limit stops), MFT (electronically variable 0-100%) Direction of rotation external switch (proportional models) electronically selectable with MFT Spring return reversible / mounting Position indication visual indicator, 0 to 95 unning time control 150 seconds default spring <60 seconds at - F [-30 ] 0 seconds at -4 F to 1 F [-0 to 50 ] Operating temperature - F to 1 F [-30 to 50 ] Housing NEM / IP54, Enclosure Type gency listings culus according to UL /--14, N/ S E :0, E according to 004/108/ E and 006/95/E Noise level less than 45 d() Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V V ½ US ND LTIN MEI 9

30 NF ctuators Multi-Function Technology iring Diagrams UTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. 5 Triac and can also be contact closures. ontrol signal may be pulsed from either the Hot (Source) or 6 ommon (Sink) 4 V line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. On/Off control 4 V/D Transformer Position ( ) Feedback VD (+) 4 V Transformer ( only) 6 a (1) ommon () Hot (3) Y Input (5) U Output MFT (1) ommon () + Hot The ZG Ω resistor converts the 4 to 0 m control signal to to 10 VD, up to actuators may be connected in parallel. 7 Position Feedback VD ( ) (+) (3) Y Input (5) U Output Meets culus or UL and S requirements without the need of an electrical ground connection. MFT NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink 30 Floating Point control Proportional to 10 or 4 to 0 m control signal P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI

31 F ctuators On/Off Dimensions with -ay Valve H P /13 - Subject to change. elimo ircontrols (US), Inc. Models F4 US F4-S US F10 US F10-S US Technical Data ontrol Power consumption F4(-S) US F10(-S) US Transformer sizing Electrical connection (-S model has cables) Electrical protection Overload protection w/built-in ux. Switches w/built-in ux. Switches on/off running 5 holding 1.5 running 6 holding.3 10 V, class power ½ conduit connector 3 ft [1m], 18 G appliance cables 10 V actuators double insulated electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <0 seconds mbient temperature - F to 1 F [-30 to 50 ] Housing NEM / IP54 gency listings UL 873, S. No. 4 certifi ed, E Noise level max. 45 d() F...-S US uxiliary switches x SPDT, 7 50 V, UL listed, one switch is fi xed at +5, one is adjustable 5 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V Dual F ctuators H Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6300V US ND LTIN MEI 31

32 F ctuators On/Off iring Diagrams 1 Provide overload protection and disconnect as required. UTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 4 VD. 4 For end position indication, interlock control, fan startup, etc., F4-S US incorporates two built-in auxiliary switches: x SPDT, 7 50 V, UL listed, one switch is fi xed at +5, one is adjustable 5 to 85. p j y 4 V Transformer 1 ommon + Hot 3 F4 US On/Off iring for 4 V/D F-08 Meets culus or UL and S requirements without the need of an electrical ground connection. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for 10 V P /13 - Subject to change. elimo ircontrols (US), Inc. 195-UX uxiliary Switches US ND LTIN MEI

33 F ctuators Multi-Function Technology Dimensions with -ay Valve P /13 - Subject to change. elimo ircontrols (US), Inc. H Models F4-MFT US F4-MFT-S US F4 w/built-in ux. Switches Technical Data ontrol MFT ontrol signal to 10 VD, (4 to 0 m with 500 Ω resistor) Ω (MFT95) Power supply 4 V ± 0% 50/60 Hz 4 VD ± 10% Power consumption running 6 holding.5 Transformer sizing 10 V, class power Electrical connection (-S model has cables) ½ conduit connector 3 ft [1m], 18 G appliance cable Overload protection electronic throughout rotation Input impedance 100 kω for to 10 VD (0.1 m) 500 Ω for 4 to 0 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback output to 10 VD, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with / mounting motor reversible with built-in switch Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <0 seconds mbient temperature - F to 1 F [-30 to 50 ] Housing NEM / IP54 gency listings UL 873, S. No. 4 certifi ed, E Noise level max. 45 d() F4-MFT-S US uxiliary switches * Dual Mounted ctuators x SPDT, 7 50 V, UL listed, one switch is fi xed at +5, one is adjustable 5 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 00V Dual F ctuators H Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6300V US ND LTIN MEI 33

34 F ctuators Multi-Function Technology iring Diagrams UTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VD. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. ontrol signal may be pulsed from either the Hot (Source) or 6 ommon (Sink) 4 V line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. On/Off control 4 V/D Transformer Position ( ) Feedback VD (+) 4 V Transformer ( only) 7 Position Feedback VD ( ) (+) 6 a (1) ommon () Hot (3) Y Input (5) U Output MFT (1) ommon () + Hot (3) Y Input (5) U Output The ZG Ω resistor converts the 4 to 0 m control signal to to 10 VD, up to actuators may be connected in parallel. Meets culus or UL and S requirements without the need of an electrical ground connection. NING Live Electrical omponents! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink MFT 30 Floating Point control Proportional to 10 or 4 to 0 m control signal 195-UXMFT P /13 - Subject to change. elimo ircontrols (US), Inc. uxiliary Switches US ND LTIN MEI

35 Multi-Function Technology P /13 - Subject to change. elimo ircontrols (US), Inc. 4 5 Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. onsult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper losed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. 4 V Transformer Low Limit ontrol 4 V Transformer Series 90 ontroller 135 ontroller 4 V Transformer Series 90 low limit control 135 for 0 to 50% control 80 for 0 to 100% control lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD High Limit ontrol 4 V Transformer Series 90 ontroller Series 90 high limit control V Transformer 4 lk (1) ommon ed () + Hot ht (3) 4 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller Shunting esistor Series 90 ontroller No. of actuators esistance esistor Kit No. ZG-03 To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD iring Multiple ctuators to a Series 90 ontroller using a Minimum Position Potentiometer 4 V Transformer Series 90 ontroller Shunting esistor 4 H05 hangeover ontroller Occupied ontact To other actuators S963 Minimum Position Potentiometer lk (1) ommon ed () + Hot 5 ht (3) ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 4 H05 hangeover ontroller Shunting esistor 4 V Transformer No. of actuators esistance esistor Kit No. ZG , 7100 ontroller Shunting esistor Y 973, 7100 T775 Q09 Minimum Position Potentiometer To other actuators To other actuators lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Occupied ontact Honeywell T675 Morning armup lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD Used with the 973 and 7100 controllers 4 V Transformer Honeywell T675 Morning armup Honeywell Q09 Minimum Position Potentiometer lk (1) ommon ed () + Hot ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD lk (1) ommon ed () + Hot 00 ht (3) 5 ht (4) ht (5) ht (6) U5 Output to 10 VD US ND LTIN MEI 35

36 GK4-3-X1 ctuators On/Off, Floating Point Dimensions with -ay Valve H Models GK4-3-X1 Technical Data Power supply Power consumption Transformer sizing Electrical connection Overload protection Operation range Y Input impedance Feedback output U ngle of rotation Torque 4V ±0% 50/60Hz 4VD ±10% 15 (1.5) 0V (class power source) 18 G plenum rated cable ½" conduit connector protected NEM (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] electronic throughout 0 to 95 rotation on/off, fl oating point 100 kω (0.1 m), 500 Ω 1500 Ω (PM, fl oating point, on/off) to 10VD, 0.5m max VD variable max. 95, adjust. with mechanical stop electronically variable 360 in-lb [40Nm] Direction of rotation reversible with switch Fail-safe position adjustable with knob or tool 0 to 100% Position indication refl ective visual indicator (snap-on) Manual override external push button unning time normal operation fail safe 95 seconds (default) variable 90 to 150 seconds 35 seconds Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM, IP54, UL enclosure type Housing material UL94-5V gency list culus acc. to UL /--14 N/S E :0 E acc. to 004/108/EE and 006/95/E Noise level < 45d() at 90 seconds Servicing maintenance free Quality standard ISO 9001 eight 3.85 lbs [1.75 kg] Valve Nominal Size Dimensions (Inches) Valve ody OP Inches DN [mm] H 6400V P /13 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MEI 36