111a. Kobold Low Flow Sensor. Alaron Vibration Transmitter. Alaron Vibration Transmitters. Alaron Machine Condition Monitor SPECIFICATIONS

Transcription

1 Alaron Vibration Transmitter Alaron Vibration Transmitters Two Wire, Loop Powered 4 20 ma Output Easily Interface To Panel Meter, Data Logger, PLC or PC Rugged PZT Sensor NEMA 4X Stainless Steel Housing The VT100 series is ideal for use with all types of rotating machinery. Continuously monitor machine vibration levels and locate problems before catastrophic failures occur. The transmitter easily mounts with a 1/4 28 stud (included). Accuracy Better than 5% Sensitivity <0.003"/ sec Frequency Range 5 Hz to 1500 Hz Supply Voltage 12 to 40 VDC unregulated Isolation 800V circuit to case Electrical Connector Microfast high temp. & oil resistant Temp. Range -10 to 100 C Shock 500G Case NEMA 4X Hermetically Sealed Size 1.8" long x 1.1" dia. VT100 Vibration Transmitter, 0 to 1"/sec. velocity w/o cable VT200 Vibration Transmitter, 0 to 2"/sec. w/o cable VT500 Vibration Transmitter, 0 to 5"/sec. w/o cable WKB3T-3 10' cable with right angle connector KB3T-3 10' cable with straight connector Alaron Machine Condition Monitor The VDS104 measures 4 channels of vibration, temperature or any 4-20mA sensor output. Each channel includes a 0-5V analog retransmit, 2 status LEDs, and 2 relay outputs with adjustable setpoint & delay. Unit is housed in a 12"x8"x6" NEMA 4X case with 4 line LCD display. Powered from 120/220VAC, the VDS104 will provide loop power to all 4 channels. VDS104 Machine Condition Monitor 111a Kobold Low Flow Sensor 0.4 to 400 GPH sizes Compact Size, Low Cost Resistant to Aggressive Media The DPL Series is ideal for applications requiring accurate flow measurement of transparent liquid media. A paddle wheel turbine interrupts an internal infra-red beam to generate a frequency output proportional to flow. The sapphire axle and bearing system assures long service life. Detector Output Sink: Pull-up: Output Signal: Emitter LED: Supply: Forward Voltage: Wiring: Wetted Parts Body: Seals: VDC, 15mA max. 18mA max. Internal 10kohm Frequency 15-50mA, VDC 6 ft. PVC cable ±5% of full scale Polypropylene, sapphire, polysulfone Buna-N standard, Viton, EPDM optional Fittings: 1 /2" bsp standard, hose-barb 1 /2" PVC optional Max. Pressure: 145 PSIG Temperature: -40 F to 160 F Protection: NEMA 4X Range Nom Freq. at Max DP Model GPH oz/sec max flow (Hz) (PSI) KO/DPL KO/DPL KO/DPL KO/DPL KO/DPL OPTIONS -V Viton seals -E EPDM seals -S Hose Barb fittings, 1 /2" PVC -F2 1/2 frequency -F4 1/4 frequency -F8 1/8 frequency -C ±1.5% accuracy calibration

2 Kobold Digital Temperature Sensor Measuring Range Programmable Features -58 to 250 F Lockout Code Dampening Semiconductor Sensor Transmitter Span Scalable 4-20mA Output Easy-to-Read LED Display All Stainless Steel Construction TDA To Order: Insert Code for Each Letter to Select Catalog Number TDA -15 A B C D Example TDA-15-N4-F2-0-L3M Display Type: 3-digit red LED Display Resolution: 0.5 from -10 to +100, 1 below -10 and above to 185 F: ±0.9 F 14 to -58 F: ±3.6 F 185 to 250 F: ±3.6 F Pressure: 1150 PSIG max. Process Temp: 250 F max. Ambient Temp: 120 F max. Material: 316L Stainless Steel housing & probe Remote Probe Cable: Teflon, 8ft. std. 24 VDC 20 ma 4-20 ma, 3-wire, 500Ω max. load Sample Rate: 0.5 Sec./sample Dampening: Averaging 2, 4,8, 16, 32, or 64 samples Electrical Connection: 4-Pin Micro-DC male plug or PVC jacketed cable Electrical Protection: NEMA 4/IP 65 Kobold Magneto-Inductive Flowmeters Liquid: Conductivity >30 µs/cm ±2.0% of full scale Repeatability: ±1% of full scale Straight Pipe: Requires 3X dia. upstream, 2X downstream Operating Temp.: F (140 F max. with PVC fittings) Pressure: 145 PSIG 70 F Pressure Drop: 3.6 PSI 100% rated flow Electrical Protection: NEMA 4X/IP 65 Power Supply: 24 VDC ±20% required Connector: Micro-DC male, 4-pin (5-pin on C34) Frequency Output PNP open collector, 200 ma max. Analog Output 4 20 ma, 3-wire, 500Ω max. Switch Output PNP or NPN open collector, 300 ma max. Compact electronic units (C34 Output Type) have a digital display and programmable switch setpoint, reset point, switch logic, 4 20 ma span/zero, dampening & lockout code. Set via 2-button keypad. Models with Integral Totalizer & Batch Controller electronics are also available. 115 Flow Rates from 0.26 GPM to 200 GPM Use with Conductive Liquids, Acids & Caustic No Moving Parts Digital Display Option Frequency or ma Output MIK-C34 A B C D MIK- Process Connection N4 1/2" NPT N5 3/4" NPT R4 1/2" BSP R5 3/4" BSP D6 Remote Probe (Smooth Shank) Measuring Range F2 0 to 250 F F3-58 to 250 F (only available with Remote Probe) H2-20 to 120 C H3-50 to 125 C (only available with Remote Probe) Probe Length 0 12mm / 1/2" (not Available with Remote Probe) 1 100mm / 4" 2 185mm / 7.25" (not Available with Remote Probe) Electrical Connection L3M Micro-DC plug, 4-Pin male L3P 3 Ft. PVC cable L3S Custom length PVC cable A B C D NEW Example MIK-5NAU4NL343 A Body Material 5NA Ryton with Buna-N Seal, 316L Electrode 5VA Ryton with FKM Seal, 316L Electrode 6FC PVDF with FFKM Seal, Hastelloy C4 Electrode B Range Fitting Set Size (") GPM N P M A U U /4 1/2 -- 1/2 U U /8 3/4 3/8 1/2 U U /2 1 1/2 1 UA UB /2 UD UE / /2 2 UG UH /4 C Fitting Set* N NPT female PVC P PVC hose barb M PVC glue socket A BSPP male D Output F300 Frequency 0-500Hz F390 User Specified Hz full scale L mA C34N 4-20mA & NPN switch C34P 4-20mA & PNP switch * PVDF butt weld tube & polypro NPT female fittings also available for some ranges.

3 Kobold Differential Pressure & Thermal Flow Sensors 1-7 through GPM Rates Bronze or Stainless Housing 4-20mA Process Output Rugged 316 Stainless Steel Bellows The RCD series uses an orifice technique to generate a differential pressure which varies with flowrate but is unaffected by system pressure fluctuations. The single measuring bellows is coupled to a high accuracy hall effect detector. Maximum Pressure: 580 PSIG Maximum Temperature: 176 F Seals: Buna-N Display: 3 digit LED 4-20mA, 3 wire Output ±3% of full scale Input 24VDC ±20%, 80mA Optional Switch: PNP or NPN open collector, 80mA max. Electronics Housing: 304 SS, NEMA 4x Electrical Connection: Micro-DC male, 5 pin KO/RCD- ABCD Example KO/RCD-1105GN4C34P A Material 11 Bronze 12 Stainless Steel B Flow Rate & Fitting Size 05GN GPM, 1 /2" NPT 10GN GPM, 1 /2" NPT 15GN GPM, 3 /4" NPT 20GN GPM, 3 /4" NPT 25GN GPM, 1" NPT 30GN GPM, 1" NPT 35GN GPM, 1 1 /2" NPT 40GN GPM, 1 1 /2" NPT 45GN GPM, 2" NPT 50GN GPM, 2" NPT 55GNB GPM, 3" NPT 60GNB GPM, 3" NPT 65GNB GPM, 3" NPT C Type C3 Compact Electronics D Output 4P 4-20mA and 1 PNP switch 4N 4-20mA and 1 NPN switch 0R 2 PNP switches 0M 2 NPN switches Options -C Calibrate for specific gravity other than water (<0.95 or >1.05) -V Calibrate for viscous liquids ( viscosity >10cSt) Gas flowmeters also available. Temperature Independent Output 8 Segment LED Flow Rate Bar Optional Setpoint Relay Wide Viscosity Range No Moving Parts Extremely Low Pressure Loss NPT & Sanitary Fittings The KAL-A uses the calorimetric principle to continuously monitor the flow of both viscous and non-viscous media. Flow rate is transmitted via a 4-20mA output, while an optional switch provides an alarm function. A single RTD element is used to both heat the probe tip and measure temperature. The internal microprocessor compensates for media temperature changes. An absence of protrusions prevents contaminants from building up on the probe tip. Sensing Range Water: m/s Oils (approx.): m/s Response Time: 5.6s typ. Maximum Pressure: 1450 PSIG (Sanitary 600 PSIG) Ambient Temperature: 0 F to 176 F CIP Temperature: 280 F Housing: NEMA 4 Nylon, Explosion Proof (Al) optional 4-20mA, 3-wire into 500Ω max. Linearity: ±10% of full scale Zero Adjustment: 0-75% of range Span Adjustment: % of range 24±2VDC, 300mA max Switch Option: Adjustment: by Potentiometer PNP open collector, 24V, 400mA max. Status Indicator: Bi-colored LED KO/KAL SS Sensor, 1 /2" NPT fitting KO/KAL Ti SS Sensor, 1 /2"" NPT fitting KO/KAL Ti SS Sensor, 3 /4" NPT fitting KO/KAL-7340S 316-Ti SS Sensor, 1 1 /2" Tri-Clamp fitting OPTIONS -P PNP Switch -M12 6 cable & Micro DC connector Also available with switch output in place of 4-20mA output. 116

4 Kobold Target-Type Flow Sensor to GPM Water, Bronze and Stainless Bodies Variety of Wetted Materials Line Sizes 3/8" to 3" NPT Compact LED display with switch and 4-20 ma flow transmitter Standard Ranges (specify bronze or stainless body): Fitting GPM water 3/8" NPT /2" NPT /4" NPT " NPT /2" NPT " NPT " NPT DPT-C Flow Range, Liquids: Repeatability: Straight Pipe Required: Operating Temperature: -10 to 176 F Maximum Pressure: F Wetted Materials: Bronze Versions: Stainless Versions: Programmable Functions: Input Display: Switch Type: Switch Rating: Analog GPM through GPM water ±3% of full scale ±1% of full scale Inlet: 10 X Diameter Outlet: 5 X Diameter Bronze, 316-Ti stainless steel, buna-n, ceramic 316-Ti stainless steel, viton, ceramic Lockout code, switch logic, switch setpoint and hysteresis, dampening 24 VDC ±20%, 80 ma Max. 3 digit LED PNP open collector 300 ma Max. short circuit protected 4-20 ma, 3-wire, RL=500 Ohms Max. Westcon Photoelectric Sensors Designed to W7703 NEMA 6 / IP67 Visible Narrow Beam for Small Object Detection Input VDC, Dual Output (PNP & NPN) Separate Power and Signal LEDs PICO Style Quick Disconnect or 6" Pig Tail Available Designed to NEMA 6 / IP67 Background Suppression Light-ON and Dark-ON Operate (Switch Selectable) Highly visible Power and Output LEDs Small Object Detection Maximum Sensing Distance: 4", 6" or 8" W7706 Small footprint, M18 Compatible Housing Visible Narrow Beam for Small Object Detection Easy Setup Separate Power and Signal LED s Retroreflective or Diffuse W7708 Polarized Retroreflective (Model 3BR) Retroreflective or Diffuse (Model 3AR) DETECTION RANGE Up to 160 ft. (48.8m) - Retroreflective Up to 12" (30.5cm) - Diffuse 10 to 30 VDC Convergent Beam DETECTION RANGE 4 in., 6 in., 8 in. (10.16, 15.2, 20.3cm) VDC Polarized Retroreflective Retroreflective or Diffuse DETECTION RANGE Up to 160 ft. (48.8m)- Retroreflective Up to 12" (30.5cm)- Diffuse 10 to 30 VDC 770 3AR 04 N 3 B QP 3AR Retro-reflective/Diffuse 3BR Polarized 04 Switch selectable (light on/dark on) POWER 3 Laser PT Pig Tail 6" standard (Micro 4 Pin) 770 6AD 04 N 3 B QP 6AD Diffuse 04 Switch selectable (light on/dark on) POWER 3 Laser (Convergent) 770 8AR 04 N 3 B QP 8AR Retroreflective 8BR Polarized Retroreflective 04 On/Off POWER 3 Laser PT Pig Tail 6 in. Standard (micro 4 pin) 117

5 Only a few products from each manufacturer are shown on our website. Please call or for information and assistance on the product you selected. WESCHLER INSTRUMENTS Manufacturer & Distributor of Meters, Instruments and related equipment Action Instruments Adalet AEMC Alaron Altek Amprobe API (Absolute Process) Applied Technical Ashcroft ATC (Westcon/Diversified) Bacharach Control Switches Crompton Dixson EIL Electro Industries E-Mon D-Mon Empro ENM Extech Flexcore Fluke Fuji Electric / TTI Hioki Hoyt Instrument Transformer International Instrument Ideal Jewell Kessler Ellis (KEP) Kobold Laurel Electronics MANUFACTURERS LFE London Electronics Madison Martel / Beta Megger / Biddle Meterman MeterMaster Midwest Transformers Modutec Monarch National Meter Newport NK Technologies Non-Linear Systems Noshok Partlow Pyragon Pyromation Raytek Red Lion Selco / Asahi Simpson Texmate Transmation Triplett Vaisala VAS / Doric Veris Weschler Westinghouse Weston (A&M) Yokogawa Meters Analog Digital Bargraph Panel Process Power Switchboard Mil Spec Large Display Meter Relays Sensors Temperature Pressure Flow Strain Position Load Voltage Current Speed Level Humidity Vibration Transducers Current Transformers Potential Transformers Shunts PRODUCTS Signal Conditioners Isolators Transmitters Looop Splitters Alarms Switches Test Equipment Multimeters Clamp-On Meters Thermometers Humidity Meters Light Meters Megohmmeters Hipot Testers Ground Testers Insulation Testers Cable Testers Power Analyzers Process Calibrators Miscellaneous Counters Timers Clocks Controllers Recorders Data Loggers Power Supplies Protection Relays Enclosures & More fax: info@weschler.com