600T Series Transmitters. Specification Sheet. Model 653T Electronic temperature transmitter (PC programmable)

Transcription

1 Specification Sheet 600T Series Transmitters Model 65T Electronic temperature transmitter (PC programmable) High flexibility and wide rangeability Single transmitter accepts RTD/THC/mV/ohm Galvanically isolated from sensor Primary element and calibration selectable User-selectable output drive under input failure conditions Complies with relevant IEC requirements for test procedure and environmental protection CENELEC Intrinsic Safety / Flameproof and Factory Mutual approvals Configurable to the actual application by standard PC 600T Series transmitter A complete family of process transmitters providing high performance in real operating conditions

2 FEATURES Model 65T electronic transmitter is an extension of the Kent- Taylor 2-wire analog product line. It is designed for factory setting, in order to meet the specific application requirement of measuring low level signals from thermocouples (THC), resistance thermometer (RTD), resistance (ohm) or e.m.f. (mv) sources. The instrument can be easily reconfigured for actual requirements by simple procedures through a standard PC equipped with a specific software available on request. (Part no. AN029) The temperature transmitter can be mounted directly on a thermowell and thermowell extension, or it can be mounted remotely on a pipestand. The transmitter assures operational security by using non-volatile memory and also handling up/down scale procedure under sensor anomalies. Compact, rugged, lightweight, easy to install and service, Kent- Taylor transmitters provide consistently reliable and stable performance under all types of process conditions, coupled with minimum maintenance requirements FUNCTIONAL SPECIFICATIONS Standard IEC 584- DIN 470 ASTM E 998 IEC 75 / DIN4760 (α = ) DIN4760 (α = ) INPUT SOURCE Linear resistance 2 wires Linear resistance wires Linear resistance 4 wires Voltage (millivolt) Sensor Thermocouple Type B Thermocouple Type E Thermocouple Type J Thermocouple Type K Thermocouple Type R Thermocouple Type S Thermocouple Type T Thermocouple Type N Thermocouple Type L Thermocouple Type U Thermocouple Type W Thermocouple Type W5 Resistance thermometer Pt 00 2 wires Resistance thermometer Pt 00 wires Resistance thermometer Pt 00 4 wires Resistance thermometer Ni 00 2 wires Resistance thermometer Ni 00 wires Resistance thermometer Ni 00 4 wires MEASURING RANGE to C (+ 752 to + 08 F) - 00 to C (- 48 to + 82 F) - 00 to C (- 48 to F) - 80 to + 70 C (- 292 to F) - 50 to C (- 58 to F) - 50 to C (- 58 to F) to C (- 28 to F) - 80 to + 00 C (- 292 to F) - 00 to C (- 48 to F) to C (- 28 to + 2 F) to C (+752 to F) to C (+752 to F) to C (- 28 to F) to C (- 28 to F) to C (- 28 to F) - 60 to C (-76 to F) - 60 to C (-76 to F) - 60 to C (-76 to F) 0 to 5000 Ω 0 to 5000 Ω 0 to 5000 Ω -0 to 800 mv MIN SPAN 200 C (60 F) 200 C (60 F) 200 C (60 F) 00 C (80 F) 75 C (5 F) 200 C (60 F) 200 C (60 F) 0Ω 0Ω 0Ω 5 mv Response Time selectable time constant (6%) to 60 sec. as defined. Loss of input The analog signal can be programmed up to a minimum value of.5 ma or a maximum value of 2 ma. Power supply (at transmitter terminals) The transmitter operates on 7 to 5 Vdc with no load and is protected against reverse polarity connection. Minimum operating voltages : 7 Vdc without options 9 Vdc with optional LCD meter For Ex ia approval power supply must not exceed 28 Vdc. Warm-up time Operation within specification in less than 5 min. Update time 0.5 sec. approx. Isolation voltage 500 Vac for 60 sec. Output signal Two-wire 4 to 20 ma dc., linear with ohms and mv or linear with true temperature for THC and RTD. Optional output meter LCD : /2 digit (±999 counts) with 0 mm (/8 in) high, 7-segment characters. Engineering unit labels are provided. Max. offset (input) 50% of maximum span value

3 Load limitations Total loop resistance including optional remote indicator line : see figure. R- Total loop resistance (Ω) 200 R(kΩ) = Supply voltage - min. operating voltage (Vdc) 2 Temperature limits Ambient -40 and +85 C (-40 and +85 F) with LCD meter : -20 and +80 C (-4 and +76 F) Storage -50 and +20 C (-58 and +248 F) with LCD meter : -40 and +85 C (-40 and +85 F) Humidity 0 to 90% RH PERFORMANCE SPECIFICATIONS For data where two values are stated the greater one should be considered for the specific case. If not otherwise stated values as % should be considered percent of calibrated span. COMMON CHARACTERISTICS Linearity error < 0.% <± 0.0% / C Signal/noise ratio min. 60 db Output meter indication accuracy LCD : ± 0.% of calibrated span ± digit Operating area Va - Supply voltage (Vdc) Supply voltage Within voltage/load specified limits the total effect is less than 0.005%/V. Load Within load/voltage specified limits the total effect is less than 0.0%/00Ω. EMI/RFI Meets EN5008 for emmission and EN50082 for immunity when instrument is properly installed with or without output meter. Vibration IEC Test FC Lloyd's specification no. : 4g / 2-00 Hz Mounting Position The transmitter may be mounted in any position with no effect on output signal. THC INPUT type E, J, K, L, N, T, U : < ±.0 C type B, R, S, W, W5 : <± 2 C cold junction compensation (CJC) : < ±.0 C type E, J, K, L, N, T, U - span <500 C : ± 0.05 C/ C - span >500 C : ± 0.0%/ C type B, R, S, W, W5 : 0.2 C/ C VOLTAGE INPUT ± 0.0 mv or ± 0.% ± µv / C or ± 0.0% / C Input resistance 0 MΩ RTD INPUT ± 0.2 C Sensor current nom. 0.2 ma span <00 C : ± 0.0 C/ C span >00 C : ± 0.0%/ C Effect of sensor cable resistance (/4 wire) <0.002 Ω/Ω Max. cable resistance per wire 5 Ω LINEAR RESISTANCE INPUT ± 0. Ω or ± 0.% ± 0.0 Ω / C or ± 0.0% / C Sensor current nom. 0.2 ma Effect of sensor cable resistance (/4 wire) < Ω/Ω Max. cable resistance per wire 5 Ω

4 Configuration The transmitter is supplied according to ordered configuration option as follows : Standard configuration Sensor type, 4-20 ma values (specify range when ordering), response time, broken sensor drive and optional LCD meter scale are in accordance with selected options. Custom configuration Customer must specify the calibration schedule to which the transmitter is to be calibrated according to the special option, in a Kent-Taylor specified format. PHYSICAL SPECIFICATIONS Materials Housing and covers Low copper aluminium alloy with baked epoxy finish; AISI 6 L ss Covers O-ring Buna N Tagging AISI 6 ss data plate attached to the electronics housing. Mounting bracket (*) Zinc plated carbon steel with chrome passivation; AISI 6 L ss Optional extras Output meter Plug-in rotatable type, LCD. Standard LCD meter scale is 0 to 00% linear; special linear scale to specified range and engineering unit is available. Supplemental customer tag AISI 6 ss tag fastened to the transmitter with stainless steel wire for customer's tag data up to a maximum of 56 characters and spaces on two lines for tag number and tag name, and up to a maximum of 28 characters and spaces for calibration details. Configuration kit Includes.5" configuration program disk, a RS22 interface unit, a cable set for transmitter and PC connection providing adaptor and the user manual (order as Part no. AN029). Mounting bracket For 60 mm. (2in) stand pipe or wall mounting. Environmental protection Wet and dust-laden atmospheres The transmitter is dust and sand tight and protected against immersion effects as defined by IEC 529 (989) to IP67. Suitable for tropical climate operation as defined in DIN , application class GQC. Hazardous atmospheres With or without output meter INTRINSIC SAFETY - CENELEC DEMKO approval; certificate no. 95D.929 EEx ia IIC T4 (Tamb -40 to +85 C)/T6 (Tamb -40 to +60 C) FLAMEPROOF - CENELEC/CESI Approval; certificate no. Ex-95.D. EEx d IIC T5 (Tamb -40 to +85 C)/T6 (Tamb -40 to +70 C) FACTORY MUTUAL : - Explosionproof: Class I, Div., Groups B, C, D - Dust ignitionproof : Class II, Div., Groups E, F, G - Suitable for : Class II, Div. 2, Groups F, G; Class III, Div., 2 - Nonincendive: Class I, Div. 2, Groups A, B, C, D - Intrinsically safe: Class I,II, III, Div., Groups A, B, C, D, E, F, G Electrical connections Two /2 NPT or M20 x.5 or PG.5 or /2 GK threaded conduit entries, direct on housing, both available for output/ supply signal when the sensor is mounted remotely. Alternatively, one /2 NPT threaded entry for integrally mounted sensor and one /2 NPT or M20 x.5 or PG.5 or /2 GK threaded entry for output/supply signal, direct on housing. Terminal block - two terminals for 4-20 ma output/supply signal wiring up to 2.5 mm 2 (4 AWG) and two jacks compatible with mm dia miniature plugs. - four terminals for input signal wiring up to.5 mm 2 (6 AWG) Grounding Internal and external 6 mm 2 (0 AWG) ground termination points are provided Mass kg approx (2 lbs) without sensor and options Packing Expanded polythene box (*) U-bolt material : AISI 400 ss; screws material: high-strength alloy steel or AISI 6ss

5 ORDERING INFORMATION Select one character or set of characters from each category and specify complete catalog number. PRODUCT CODE abcde f gh i j k l mn o BASE MODEL INPUT SENSOR ELECTRICAL CERTIFICATION HOUSING OUTPUT METER MOUNTING BRACKET CALIBRATION/CERTIFICATE YY 00 abcde BASE MODEL - st to 5th characters Temperature Transmitter Codice 65TY f INPUT SENSOR - 6th character Remote Integrally mounted (NOTE ) (one /2" NPT CONNECTION ENTRY IS PROVIDED) NOTE : quoted separately 5 gh i 7th and 8th characters Use code ELECTRICAL CERTIFICATION - 9th character General Purpose Intrinsic Safety to CENELEC EN5004/20 DEMKO approval to EEx ia IIC T6/T4 Flameproof to CENELEC EN5004/8 CESI approval to EEx d IIC T6/T5 (NOTE 2) Intrinsic Safety and Flameproof, as above, CESI approval (NOTE 2) Factory Mutual (FM) (only available with Remote sensor and /2" NPT electrical connections) NOTE 2 : if integral sensor is required this must be supplied by ABB Kent-Taylor Lenno YY 2 U 7 HOUSING - 0th character j Material Aluminium alloy AISI 6 L ss Electrical connections /2" NPT CM 20 Pg.5 /2" GK /2" NPT CM 20 Pg.5 /2" GK 2 4 A C D F k OUTPUT METER - th character None Digital LCD linear 0-00% user scalable Digital LCD linear scale (specify range and engineering units) 5 l MOUNTING BRACKET- 2th character None Carbon steel AISI 6 L ss 2 mn th - 4th character Use code 00 o CALIBRATION CERTIFICATE - 5th character Not required For the transmitter only For the transmitter and the integrally mounted input sensor 4

6 ELECTRICAL CONNECTIONS Internal ground termination point INPUT TYPE Thermocouple and voltage Resistance thermometer and Linear resistance TERMINAL CONNECTION Terminal 5 = positive Terminal 4 = negative Terminal and 6 = inputs Terminal 4 = rd wire (if any) Terminal 5 = 4th wire (if any) NOTE: Use terminals and 6 for external CJC of thermocouple (if any by Pt 00) External ground termination point Connection entry for integrally mounted sensor Line load GND + Power - - source + Optional Receiver DIMENSIONS AND MOUNTING DETAILS (Not for construction unless certified) Electrical connection 00 (.9) Locking fastener for cover (EEx d only) Meter housing 00 (.9) 5 (0.59) ENERGISED NOT OPEN WHILE! Certification tag DO WARNING UNDER HAZARDOUS CONDITIONS C 28 (5.0) Serial No. Terminals side 65 (2.56) 5 (2.08) 90 (.54) 70 (6.69) The Company's policy is one of continuous product improvement and the right is reserved to modify the specifications contained herein without notice. SS/65T Rev 4 ABB Instrumentation spa Via Statale 2206 Lenno (Como) Italia Tel. (044) 58 Facsimile (044) ABB Automation Ltd. Howard Road St. Neots, Cambs. England PE9 EU Tel. (0480) 4752, Facsimile (0480) ABB Automation Inc. 25 East County Line Road Warminster, Pa USA Tel. (25) /620/6777 Facsimile (25)