WiMAX Forum Mobile System Profile Release 1.0 Approved Specification (Revision 1.2.2: )

Transcription

1 WiMAX Forum Mobile System Profile Page -

2 Copyright otice, Use Restrictions, Disclaimer, and Limitation of Liability. Copyright 00 WiMAX Forum. All rights reserved. The WiMAX Forum TM owns the copyright in this document and reserves all rights herein. This document is available for download from the WiMAX Forum and may be duplicated for internal use, provided that all copies contain all proprietary notices and disclaimers included herein. Except for the foregoing, this document may not be duplicated, in whole or in part, or distributed without the express written authorization of the WiMAX Forum. Use of this document is subject to the disclaimers and limitations described below. Use of this document constitutes acceptance of the following terms and conditions: THIS DOCUMET IS PROVIDED AS IS AD WITHOUT WARRATY OF AY KID. TO THE GREATEST EXTET PERMITTED BY LAW, THE WiMAX FORUM DISCLAI ALL EXPRESS, IMPLIED AD STATUTORY WARRATIES, ICLUDIG, WITHOUT LIMITATIO, THE IMPLIED WARRATIES OF TITLE, OIFRIGEMET, MERCHATABILITY AD FITESS FOR A PARTICULAR PURPOSE. THE WiMAX FORUM DOES OT WARRAT THAT THIS DOCUMET IS COMPLETE OR WITHOUT ERROR AD DISCLAI AY WARRATIES TO THE COTRARY. Any products or services provided using technology described in or implemented in connection with this document may be subject to various regulatory controls under the laws and regulations of various governments worldwide. The user is solely responsible for the compliance of its products and/or services with any such laws and regulations and for obtaining any and all required authorizations, permits, or licenses for its products and/or services as a result of such regulations within the applicable jurisdiction. OTHIG I THIS DOCUMET CREATES AY WARRATIES WHATSOEVER REGARDIG THE APPLICABILITY OR O-APPLICABILITY OF AY SUCH LAWS OR REGULATIOS OR THE SUITABILITY OR O-SUITABILITY OF AY SUCH PRODUCT OR SERVICE FOR USE I AY JURISDICTIO. OTHIG I THIS DOCUMET CREATES AY WARRATIES WHATSOEVER REGARDIG THE SUITABILITY OR O-SUITABILITY OF A PRODUCT OR A SERVICE FOR CERTIFICATIO UDER AY CERTIFICATIO PROGRAM OF THE WiMAX FORUM OR AY THIRD PARTY. The WiMAX Forum has not investigated or made an independent determination regarding title or noninfringement of any technologies that may be incorporated, described or referenced in this document. Use of this document or implementation of any technologies described or referenced herein may therefore infringe undisclosed third-party patent rights or other intellectual property rights. The user is solely responsible for making all assessments relating to title and noninfringement of any technology, standard, or specification referenced in this document and for obtaining appropriate authorization to use such technologies, standards, and specifications, including through the payment of any required license fees. OTHIG I THIS DOCUMET CREATES AY WARRATIES OF TITLE OR OIFRIGEMET WITH RESPECT TO AY TECHOLOGIES, STADARDS OR SPECIFICATIOS REFERECED OR ICORPORATED ITO THIS DOCUMET. I O EVET SHALL THE WiMAX FORUM OR AY MEMBER BE LIABLE TO THE USER OR TO A THIRD PARTY FOR AY CLAIM ARISIG FROM OR RELATIG TO THE USE OF THIS DOCUMET, ICLUDIG, WITHOUT LIMITATIO, A CLAIM THAT SUCH USE IFRIGES A THIRD PARTY S ITELLECTUAL PROPERTY RIGHTS OR THAT IT FAILS TO COMPLY WITH APPLICABLE LAWS OR REGULATIOS. BY USE OF THIS DOCUMET, THE USER WAIVES AY SUCH CLAIM AGAIST THE WiMAX FORUM AD ITS MEMBERS RELATIG TO THE USE OF THIS DOCUMET. The WiMAX Forum reserves the right to modify or amend this document without notice and in its sole discretion. The user is solely responsible for determining whether this document has been superseded by a later version or a different document. WiMAX, Mobile WiMAX, WiMAX Forum, WiMAX Certified, WiMAX Forum Certified, the WiMAX Forum logo and the WiMAX Forum Certified logo are trademarks of the WiMAX Forum. Third-party trademarks contained in this document are the property of their respective owners. Page -

3 TABLE OF COTETS ABSTRACT.... SCOPE.... REFERECES.... DEFIITIOS.... ABBREVIATIOS.... DEFIITIOS OF SYSTEM PROFILES.... COVETIOS..... Item column..... Description column..... Reference column..... Status column..... BS/ column..... BS/ Values column..... column.... PHY PROFILE.... PROFILES OF BS AD..... System Parameters PHY Mode Sampling Factor Cyclic Prefix Frame Length TTG/RTG umber of OFDM Symbols in DL and UL..... Subcarrier Allocation DL Subcarrier Allocation UL Subcarrier Allocation Common SYC Symbol UL Sounding UL Control Channels Initial Ranging HO Ranging Periodic Ranging BW Request Fast-Feedback/CQI Channel Encoding Fast-Feedback/CQI Channel Allocation Method..... Channel Coding Repetition Randomization Convolutional Code Convolutional Turbo Code BTC LDPC Interleaving..... H-ARQ Support... Page -

4 Chase Combining Incremental Redundancy ACK Channel..... Control Mechanism Synchronization Closed-loop Power Control Open-loop Power Control..... Channel Measurement CIR Measurement RSSI Measurement Modulation PRBS (Subcarrier Randomization) Downlink Uplink Pilot Modulation Preamble Modulation Ranging Modulation MAP Support ormal MAP Compressed MAP Sub-DL-UL MAP H-ARQ MAP Message Extended HARQ IE in the ormal MAP DL Region Definition AAS AAS Zone Support Supported Permutation in DL Supported Permutation in UL AAS DL Preamble AAS UL Preamble Diversity MAP Scan DL AAS-SDMA Pilots UL AAS-SDMA Pilots AAS Private MAP AAS-FBCK-REQ/RSP support..... STC/MIMO Supported Features for DL PUSC Supported Features for DL FUSC Supported Features for DL Optional FUSC Supported Features for DL Optional AMC Supported Features for DL PUSC-ASCA Supported Features in UL PUSC Supported Features in UL Optional PUSC Supported Features in UL Optional AMC Closed-Loop MIMO MIMO Feedback MIMO Midamble... Page -

5 MIMO Soft-Handover Based Macro-diversity H-ARQ Downlink Support for MIMO H-ARQ Uplink Support for MIMO..... HO Support in PHY FBSS MIMO Soft-handover based macro-diversity transmission UL Macro diversity.... PERFORMACE/FIDELITY REQUIREMETS..... Minimum Performance SSTTG/SSRTG Max DL Concurrent Bursts Max Bursts in DL Subframe Max umber of Zones in DL/UL Subframe Measurement Processes and CQI Channels Max H-ARQ Bursts in DL/UL Subframe..... Transmit Requirements..... Receiver Requirements..... Frequency and Time Synchronization Requirements...9. MAC PROFILE.... PROFILES OF BS AD..... PHS..... CS Options..... MAC PDU formats..... MAC Support of PHY layer Feedback Mechanism..... Multicast connection..... etwork Entry..... ARQ MAC support for H-ARQ QoS Data delivery services for mobile network..... Request-Grant mechanism..... eighbor Advertisement Scanning and Association Scanning Scan Reporting Type Support Association Association Type Support HO/Scan/Report Trigger Metrics..... MAC layer HO procedures..... HO Optimization..... CID and SAID Update..... Fast BS Switching Macro Diversity Handover Sleep Mode Idle Mode..... Expedited etwork Re-entry from Idle Mode... Page -

6 Security Authorization Policy Support PKM Version Support PKMv Authorization policy support initial network entry PKMv Authorization policy support network re-entry Supported cryptographic suites Message Authentication Code Mode Security Association SA Service Type EAP Authentication methods Certificate profile Multicast Broadcast Re-keying Algorithm (MBRA) MBS AAS 's etwork Entry issued by BS restart PARAMETERS...8. RECOMMEDED COFIGURATIO...8. RADIO PROFILE...8. POWER CLASS PROFILE...89 Page -

7 LIST OF TABLES TABLE. STATUS COLUM ETRIES... TABLE. REQUIRED COLUM ETRIES... TABLE. VALUE COLUM ETRIES... TABLE. PHY MODE... TABLE. BAD CLASS IDEX... TABLE. SAMPLIG FACTOR... TABLE. CYCLIC PREFIX... TABLE 8. FRAME LEGTH... TABLE 9. TTG/RTG... TABLE 0. UMBER OF OFDM SYMBOLS I DL AD UL... TABLE. DL SUBCARRIER ALLOCATIO...8 TABLE. UL SUBCARRIER ALLOCATIO...9 TABLE. COMMO SYC SYMBOL...9 TABLE. UL SOUDIG...9 TABLE. UL SOUDIG...0 TABLE. IITIAL RAGIG... TABLE. HO RAGIG... TABLE 8.PERIODIC RAGIG... TABLE 9. BW REQUEST... TABLE 0. FAST-FEEDBACK/CQI CHAEL ECODIG... TABLE. FAST-FEEDBACK/CQI CHAEL ALLOCATIO METHOD... TABLE. REPETITIO... TABLE. RADOMIZATIO... TABLE. COVOLUTIOAL CODE... TABLE. COVOLUTIOAL TURBO CODE... TABLE. BLOCK TURBO CODE... TABLE. LOW DESITY PARITY CHECK CODE... TABLE 8. ITERLEAVIG... TABLE 9. CHASE COMBIIG H-ARQ... TABLE 0. HARQ PARAMETERS FOR CHASE WITH CTC... TABLE. ICREMETAL REDUDACY H-ARQ... TABLE. ACK CHAEL... TABLE. SYCHROIZATIO... TABLE. CLOSED-LOOP POWER COTROL... TABLE. OPE-LOOP POWER COTROL... TABLE. CIR MEASUREMET...8 TABLE. RSSI MEASUREMET...9 TABLE 8. PRBS...0 TABLE 9. DOWLIK MODULATIO...0 TABLE 0. UPLIK MODULATIO...0 TABLE. PILOT MODULATIO...0 TABLE. PREAMBLE MODULATIO... TABLE. RAGIG MODULATIO... TABLE. ORMAL MAP... TABLE. COMPRESSED MAP... TABLE. SUB-DL-UL MAP... TABLE. H_ARQ MAP MESSAGE... TABLE 8. EXTEDED H-ARQ IE I ORMAL MAP... TABLE 9. DL REGIO DEFIITIO SUPPORT... TABLE 0. AAS ZOE SUPPORT... Page -

8 TABLE. SUPPORTED PERMUTATIO I DL... TABLE. SUPPORTED PERMUTATIO I UL... TABLE. AAS DL PREAMBLE... TABLE. AAS UL PREAMBLE... TABLE. DIVERSITY MAP SCA... TABLE. DL AAS-SDMA PILOTS... TABLE. UL AAS_SDMA PILOTS... TABLE 8. AAS PRIVATE MAP... TABLE 9. AAS_FBCK/RSP SUPPORT... TABLE 0. SUPPORTED FEATURES FOR DL PUSC... TABLE. SUPPORTED FEATURES FOR DL FUSC... TABLE. SUPPORTED FEATURES FOR DL OPTIOAL FUSC... TABLE. SUPPORTED FEATURES FOR DL OPTIOAL AMC...8 TABLE. SUPPORTED FEATURES FOR DL PUSC-ASCA...9 TABLE. SUPPORTED FEATURES I UL PUSC...9 TABLE. SUPPORTED FEATURES I UL OPTIOAL PUSC...9 TABLE. SUPPORTED FEATURES I UL OPTIOAL AMC...0 TABLE 8. CLOSED-LOOP MIMO...0 TABLE 9. MIMO FEEDBACK... TABLE 0. MIMO MIDAMBLE... TABLE. MIMO SOFT-HADOVER MACRO-DIVERSITY... TABLE. H-ARQ DOWLIK SUPPORT FOR MIMO... TABLE. H-ARQ UPLIK SUPPORT FOR MIMO... TABLE. FAST BASE STATIO SWITCHIG... TABLE. MIMO SOFT-HADOVER BASED MACRO-DIVERSITY TRASMISSIO... TABLE. UL MACRO DIVERSITY... TABLE. SSTTG/SSRTG... TABLE 8. MAXIMUM DL COCURRET BURSTS... TABLE 9. MAX BURSTS I DL SUBFRAME... TABLE 80. MAX UMBER OF ZOES I DL AD UL SUBFRAMES... TABLE 8. MEASUREMET PROCESSES AD CQI CHAELS... TABLE 8. MAX H-ARQ BURSTS... TABLE 8. TRASMITTER REQUIREMETS... TABLE 8. RECEIVER REQUIREMETS... TABLE 8. FREQUECY AD TIME SYCHROIZATIO REQUIREMETS...9 TABLE 8. PHS... TABLE 8. COVERGECE SUBLAYER OPTIOS... TABLE 88. MAC PDU FORMATS... TABLE 89. FEEDBACK MECHAISM... TABLE 90. MULTICAST COECTIO... TABLE 9. ETWORK ETRY... TABLE 9. ARQ... TABLE 9. MAC SUPPORT FOR HARQ... TABLE 9. QOS... TABLE 9. DATA DELIVERY SERVICES FOR MOBILE ETWORK... TABLE 9. REQUEST-GRAT MECHAISM... TABLE 9. EIGHBOR ADVERTISEMET...8 TABLE 98. SCAIG...8 TABLE 99. SCA REPORTIG TYPE SUPPORT...9 TABLE 00. ASSOCIATIO...9 TABLE 0. ASSOCIATIO TYPE SUPPORT...0 Page - 8

9 TABLE 0. HO/SCA/REPORT TRIGGER METRICS... TABLE 0. MAC LAYER HO PROCEDURES... TABLE 0. HO OPTIMIZATIO... TABLE 0. CID AD SAID UPDATE... TABLE 0. FAST BASE STATIO SWITCHIG... TABLE 0. MACRO DIVERSITY HADOVER... TABLE 08. SLEEP MODE...9 TABLE 09. IDLE MODE... TABLE 0. EXPEDITED ETWORK RE-ETRY FROM IDLE MODE... TABLE. AUTHORIZATIO POLICY SUPPORT... TABLE. PKM VERSIO SUPPORT... TABLE. PKMV AUTHORIZATIO POLICY SUPPORT-IITIAL ETWORK ETRY... TABLE. PKMV AUTHORIZATIO POLICY SUPPORT-ETWORK RE-ETRY... TABLE. SUPPORTED CRYPTOGRAPHIC SUITES... TABLE. MESSAGE AUTHETICATIO CODE MODE...8 TABLE. SECURITY ASSOCIATIO...8 TABLE 8. SA SERVICE TYPE...9 TABLE 9. EAP AUTHETICATIO METHODS...9 TABLE 0. CERTIFICATE PROFILE...9 TABLE. SERVICE TYPE...9 TABLE. MBS...80 TABLE. AAS...80 TABLE. 'S ETWORK ETRY ISSUED BY BS RESTART...8 TABLE. PARAMETERS...8 TABLE. MIIMUM PERFORMACE REQUIREMETS...8 TABLE. RECOMMEDED COFIGURATIOS...8 TABLE 8. RF PROFILES LIST...8 TABLE 9. POWER CLASSES...89 Page - 9

10 8 9 0 Participants This document was developed by the WiMAX Forum TM Technical Working Group (TWG). Co-chair; Wonil Roh, Samsung Co-chair: Vladimir Yanover, Alvarion Editor: Hassan Yaghoobi, Intel Corp. Following is the list of voting member companies during the development of this document. Adaptix, Agilent, Airspan, Alcatel, Alvarion, Amicus, Aperto etworks, ArrayComm, Beceem, British Telecom, Broadcom, AT Wireless, extwave, Ericsson, ETRI, Fujitsu, Huawei Technologies, Intel Corp., KDDI, KT Corp., LG Electronics, Lucent Technologies, Marvell, Mitsubishi Electronics, Motorola, avini, EC, okia, ortel etworks, PMC Sierra, Posdata, Redline, Rhode and Schwartz, Runcom Technologies Ltd., Samsung, SEQUAS Communications, Siemens Mobile, Soma etworks, Sprint, SR Telecom, Telecom Italia, Texas Instruments, Wavesat and ZTE Corp. Page - 0

11 Abstract This document is prepared by the Technical Working Group (TWG) to provide the descriptions of the OFDMA based system profiles of Mobile WiMAX.. Scope The main objective of this document is to provide OFDMA System Profile specification of mobile network, complementary to as amended by 80.e-00 standard, primarily for the purpose of certification of conformant Subscriber Stations and Base Stations. Page -

12 References [] IEEE Standard , IEEE Standard for Local and Metropolitan Area etworks - Part : Air Interface for Fixed Wireless Access Systems. [] IEEE Standard 80.e-00, Amendment to IEEE Standard for Local and Metropolitan Area etworks - Part : Air Interface for Fixed Broadband Wireless Access Systems- Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands [] WiMAX Forum TM Mobile Certification Profile, WiMAX, Certification Working Group, April 00 [] IEEE /Cor Ballot ary 80-0_0r.cmt, IEEE 80. Working Group, ovember 00 Page -

13 Definitions For the purposes of the present document, the following terms and definitions apply:. Abbreviations. Definitions of system profiles Profile definitions of different devices/usage models and releases are provided in this subsection.. Conventions.. Item column The Item column contains a number that identifies each description in the table... Description column The description column describes in free text each respective item (e.g., parameters, timers, etc.)... Reference column The reference column indicates the section of [] and [] from which the requirement for the item is derived... Status column The following notations are used in the status column to indicate whether each item is mandatory or optional in IEEE standard based on [] as amended by 80.e-00 []. Table. Status Column Entries m Explicitly shown as mandatory in the standard. It is required to implement pm Potentially mandatory, required for the system to perform basic operations (ot explicitly shown as mandatory in the standard). It is required to implement. o Explicitly mentioned as optional in the standard or is not explicitly mentioned but has capability negotiations. It may or may not be implemented. oi Qualified option for mutually exclusive or selectable options from a set. One or more of the options from the set shall be supported. po Potentially optional. ot explicitly mentioned as mandatory, but from the standard we may conclude it is, though not really required for the system to perform basic operations. We have to decide whether it should be defined as optional n/a ot applicable in the given context, it is impossible to use the capability. Page -

14 BS/ column The column indicates whether the item is required for every BS/ to implement for WiMAX certification purposes. Y or y. or n IO- n/a Table. Column Entries to implement ot required to implement. Inter-operable Options: Item belongs to group of features for which it is requested to provide testing procedure and distinct labeling of BS equipment. More specifically The item is not required to get general WiMAX certified label and Is required to get distinct WiMAX certified with capability label. ot applicable The following Inter-operable Options are defined and used in this document.. IO-MIMO: Group of Inter-operable Option features related to Multiple Input Multiple Output (MIMO) operation.. IO-BF: Group of Inter-operable Option features related to Beam Forming (BF) operation.. IO-MBS: Group of Inter-operable Option features related to Multicast and Broadcast Services (MBS) operation.. IO-ETHx (x =,, ): Groups of Inter-operable Option features related to Ethernet CS.. BS/ Values column This column indicates the specific value or range of values for each BS/ to implement for WiMAX certification purposes. 8 xx aa - bb n/a Table. Value Column Entries Set to value xx Set to range aa - bb ot applicable column This column provides additional clarification and reasoning for each item. Page -

15 . PHY Profile Profiles of BS and.. System Parameters... PHY Mode Table. PHY Mode OFDMA 8. m Y Y OFDMA is the sole PHY mode within the scope of this document.... Band Class Index System profile requirements of this document are applied to the following band class indices. Each index shall specify one frequency range and one or more combinations of channel bandwidth, FFT size, channel raster and duplexing mode. BS support for a particular band class requires support of a frequency range that is a subset of the complete frequency range defined by the band-class. The BS vendor shall provide a declaration of the supported frequency range. The supported frequency range shall be a minimum of three () times the largest supported channel bandwidth. must support the entire range of frequency defined by a band class (or sub-bands) while the BS is required to support only sub-range of the band class declared by vendor. Band Class Index Frequency Range (GHz) Channel Frequency Step (khz) , (00 KHz step size is also Table. Band Class Index Channel Bandwidth(s) (MHz) FFT Size Duplexing Mode TDD 0 0 TDD 8. 0 TDD. TDD TDD 0 0 TDD TDD 0 0 TDD s Both bandwidths must be supported by the Both bandwidths must be supported Page -

16 recommended for band class in Europe) Sampling Factor TDD 0 TDD 0 0 TDD TDD 0 TDD 0 0 TDD TDD 0 TDD 0 0 TDD TDD 0 TDD 0 0 TDD to by the Table. Sampling Factor If channel bandwidth is a 8... m Y Y multiple of.mhz then n=8/ else if channel bandwidth is a multiple of any of.,., or. MHz then n=8/ else if not otherwise specified then n=8/.... Cyclic Prefix Table. Cyclic Prefix / 8... oi / oi Y Y / 8... oi / 8... oi... Frame Length Table 8. Frame Length 0 ms 8... oi oi oi Page -

17 oi 8... oi Y Y 8... oi oi oi... TTG/RTG This parameter shall be applicable only to TDD mode. Table 9. TTG/RTG BS Values TTG 8... m Y 9 PS for 0 MHz, 8 PS for 8. MHz, PS for MHz, 8 PS for MHz and 88 PS for. MHz RTG 8... m Y 8 PS for 0 MHz, 8 PS for 8. MHz, 0 PS for MHz, 8 PS for MHz and 0 PS for. MHz n/a n/a us minimum specified in the referred section. The requirement is equivalent to " msec - (RTG+ umber of OFDM symols x symbol duration)" where "umber of OFDM symols" = for 0 and MHz, for 8. MHz and for MHz. us minimum specified in the referred section. The requirement is equivalent to 0 us for, 0 and MHz BW and. us for 8. MHz BW.... umber of OFDM Symbols in DL and UL This feature shall be applicable to TDD operation only and specifies number of OFDM symbols in DL and UL subframes. Table 0. umber of OFDM Symbols in DL and UL BS Values Values Page -

18 umber of 8... oi Y (, ), OFDM (, ), Symbols (, ), in DL and (, ), UL for (, ), and 0 (0, ), MHz BW (9, 8), (8, 9), (, 0), umber of OFDM Symbols in DL and UL for 8. MHz BW umber of OFDM Symbols in DL and UL for and. MHz BW.. Subcarrier Allocation (, ) 8... oi Y (0, ), (9, ), (8, ), (, ), (, ), (, ), (, 8) 8... oi Y (, 09), (, 0), (, ), (, ), (0, ), (9, ), (8, )... DL Subcarrier Allocation BS Values Values Y Y Y The same as BS values The same as BS values The same as BS values Table. DL Subcarrier Allocation Require d PUSC 8... m Y Y PUSC w/ all subchannels 8... po Y Y PUSC w/ dedicated pilots 8... po IO-BF Y Also refer [] and 8... FUSC 8... po Y Y FUSC w/ dedicated pilots 8... po and 8... Optional FUSC 8... o O-FUSC w/ dedicated pilots 8... o and AMC x 8... o Page - 8

19 AMC x 8... o Y Y AMC x 8... o Default Type 8... and... o Only applicable with HARQ_MAP 9 AMC x w/ dedicated pilots 8... and 8... o AMC x w/ dedicated pilots 8... and 8... o IO-BF Y Also refer [] AMC x w/ dedicated pilots 8... and 8... o 0 PUSC-ASCA 8... o... UL Subcarrier Allocation Table. UL Subcarrier Allocation. PUSC 8... po Y Y. PUSC w/o subchannel rotation o IO-BF Y Also refer []. Optional PUSC 8... o. AMC x 8... o AMC x 8... o Y Y Also refer [] AMC x 8... o. Mini-subchannel 8... o Only for PUSC & O-PUSC... Common SYC Symbol Table. Common SYC Symbol 8 Support of the Common SYC Symbol... UL Sounding 8... o 9 Table. UL Sounding Type A w/ Cyclic shift o IO-BF Y support for P values other than 9 and 8 Page - 9

20 Type A w/ Cyclic shift 8... o IO-BF Y Support P values of 9 and 8 Type A w/ Decimation 8... o IO-BF Y Type B 8... o Send Sounding Report 8... o Flag Direct transmission of DL channel coefficients (Include additional feedback, option 0b0) Decimation with randomization 8 Power Assignment Method: Equal Power (0b00) 9 Power Assignment Method: Interference dependent. Per subcarrier power limit; (0b0) 0 Power Assignment Method: Interference dependent. Total power limit.; (0b) 8... and 8... o 8... o 8... and and and 8... Power Boost 8... and 8... Feedback of Received Pilot Coefficients (include additional feedback option = 0b0) Feedback of message (include additional feedback option = 0b) 8... and 8... oi IO-BF Y oi oi o o 8... o Table. UL Sounding Item Description Reference Status Value Sounding response time capability max number of simultaneous sounding 8... and and.8... o Y ext Frame o Y This parameter specifies the max number of sounding transmutations Page - 0

21 instructions.. UL Control Channels... Initial Ranging by in a frame. Table. Initial Ranging Initial Ranging in PUSC zone w/ symbols Initial Ranging in PUSC zone w/ symbols Initial Ranging in Optional PUSC zone w/ symbols Initial Ranging in Optional PUSC zone w/ symbols Initial Ranging in AMC zone w/ symbols Initial Ranging in AMC zone w/ symbols... HO Ranging 8... oi 8... oi 8... oi 8... oi 8... oi 8... oi Y Y 8 Table. HO Ranging 9 0 HO Ranging in PUSC zone w/ symbols HO Ranging in PUSC zone w/ symbols HO Ranging in Optional PUSC zone w/ symbols HO Ranging in Optional PUSC zone w/ symbols HO Ranging in AMC zone w/ symbols HO Ranging in AMC zone w/ symbols... Periodic Ranging 8... o 8... o 8... o 8... o 8... o 8... o Y Y Table 8.Periodic Ranging Page -

22 Periodic Ranging in PUSC zone w/ symbols Periodic Ranging in PUSC zone w/ symbols Periodic Ranging in Optional PUSC zone w/ symbols Periodic Ranging in Optional PUSC zone w/ symbols Periodic Ranging in AMC zone w/ symbols Periodic Ranging in AMC zone w/ symbols... BW Request 8... oi 8... oi 8... oi 8... oi 8... oi 8... oi Y Y Table 9. BW Request BW Request in PUSC zone w/ symbols BW Request in PUSC zone w/ symbols BW Request in Optional PUSC zone w/ symbols BW Request in Optional PUSC zone w/ symbols BW Request in AMC zone w/ symbols BW Request in AMC zone w/ symbols 8... oi 8... oi 8... oi 8... oi 8... oi 8... oi... Fast-Feedback/CQI Channel Encoding Y Y 8 9 Table 0. Fast-Feedback/CQI Channel Encoding bits po bits o Y Y bits o Primary/Secondary o This feature is needed for FBSS. ote on Item : If the "Feedback Type" in CQICH_Alloc_IE() is set to "0b0 = Effective CIR Feedback" and the negotiation capability Type, bit# = Enhanced FAST_FEEDBACK is Page -

23 enabled which indicates support for "-bit CQI", the reported effective CIR shall be in the 0b00xxxx format where the LSBs is described in Table 98b of Section in [].... Fast-Feedback/CQI Channel Allocation Method Table. Fast-Feedback/CQI Channel Allocation Method 8 9 Fast-Feedback Allocation Subheader support Fast feedback channel allocation using CQICH Allocation IE Fast feedback channel allocation using CQICH Enhanced Allocation IE.. Channel Coding... Repetition... o 8... o Y Y 8... o 0 Table. Repetition Repetition 8..9 m Y Y FCH uses repetition coding (8...)... Randomization Table. Randomization Randomization m Y Y... Convolutional Code Table. Convolutional Code Tail Biting m Y Y Zero Tail o Page -

24 ... Convolutional Turbo Code Table. Convolutional Turbo Code CTC excluding BTC o Y Y Table. Block Turbo Code BTC o... LDPC Table. Low Density Parity Check Code LDPC o... Interleaving Table 8. Interleaving Interleaving m Y Y The interleaving subject of this section should not be applied to CTC mode. Optional interleaver for CC.. H-ARQ Support and.8... o This interleaver mode is only applicable to Convolutiona l Encoding Page -

25 ... Chase Combining Table 9. Chase Combining H-ARQ Chase w/ CC 8... o Chase w/ CTC 8... o Y Y Chase with LDPC 8... o Item Parameter Description Table 0. HARQ Parameters for Chase with CTC Reference Values H-ARQ DL Buffer size per channel H-ARQ UL Buffer size per channel DL Aggregate flag for HARQ buffer UL Aggregate flag for HARQ buffer HARQ ACK Delay for DL Burst HARQ ACK Delay for UL Burst Category =,8 (K=0), Category = 89 (K=), Category =,8 (K=0), Category =,0 (K=) Category =,8 (K=0), Category =,8 (K=0), Category =,8 (K=0), Category =,8 (K=0) Category = O or OFF, Category = O, Category = O, Category = O Category = OFF, Category = O, Category = O, Category = O...,.....,.. /A Status for the four categories is oi, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. Status for the four categories is oi, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. Status for the four categories is oi, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. Status for the four categories is i.o, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. Page -

26 Item Parameter Description Reference Values umber of DL H- ARQ Channels supported by 8 umber of UL H- ARQ Channels supported by.8... and. D.8... and. D Category =, Category =, Category =, Category = Category =, Category = 8, Category = 8, Category = 8 Status for the four categories is oi, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. Status for the four categories is oi, that is support for values of items - and -8 corresponding to one or more of the categories from the set shall be supported. ote that the HARQ buffer size shall be interpreted as softbits buffer size, i.e. relating to coded data bits and not un-coded. This means the buffer size refers to both the systematic and parity bits transmitted over the air. It is left to vendor s implementation to determine the amount of memory space for each bit of transmitted information. The buffer size is related to buffer size parameter K according to the following Equation. ( K / ) Buffer size = floor[ * ]... Incremental Redundancy Table. Incremental Redundancy H-ARQ IR w/ CC o IR w/ CTC o... ACK Channel Table. ACK Channel 8 ACKCH 8... m Y Y Conditioned by H-ARQ" support.. Control Mechanism Page -

27 ... Synchronization Table. Synchronization BS Synchronization in time /slot BS Synchronization in frequency BS to eighbor BS Synchronization in frequency ,... o Y /A Refer to "Time/Frequency Synchronization Indicator" in Table 08h of the referred section o Y /A... o Y /A Refer to "Time/Frequency Synchronization Indicator" in Table 08h of the referred section. SS Synchronization m /A Y... Closed-loop Power Control 8 Table. Closed-loop Power Control CL Power Control m Y Y... Open-loop Power Control Table. Open-loop Power Control OL Power Control o Y Y Passive Uplink open loop o Y Y power control Active Uplink open loop o power control UL Tx power and Headroom transmission condition using bandwidth request and UL Tx Power Report header and... o Y Y Page -

28 UL Tx power and Headroom transmission condition using PHY channel report header UL Tx power and Headroom transmission condition using Tx power report extended subheader.. Channel Measurement... CIR Measurement and and... o o Table. CIR Measurement Physical CIR measurement from the preamble for frequency reuse== (feedback type=0b00 and report type=0 and CIR preamble report type=0) Physical CIR measurement from the preamble for frequency reuse== (feedback type=0b00 and report type=0 and CIR preamble report type=) Physical CIR measurement for a permutation zone from pilot subcarriers (feedback type=0b00 and report type= and CIR zone measurement type=0) Physical CIR measurement for a permutation zone from data subcarriers (feedback type=0b00 and report type= and CIR zone measurement type=) Effective CIR measurement from the preamble for frequency reuse== (feedback type=0b0 and report type=0 and CIR preamble report type=0)..8, 8..., 8... and , 8..., 8... and , 8..., 8... and , 8..., 8... and , 8..., 8... and oi Y Y oi Y Y oi Y Y Also refer [] oi oi This option provides capability to the to report MCS preference to BS. Page - 8

29 Effective CIR measurement from the preamble for frequency reuse== (feedback type=0b0 and report type=0 and CIR preamble report type=) Effective CIR measurement for a permutation zone from pilot subcarriers (feedback type=0b0 and report type= and CIR zone measurement type=0) 8 Effective CIR measurement for a permutation zone from data subcarriers (feedback type=0b0 and report type= and CIR zone measurement type=) 9 Support for concurrent CQI channels with effective CIR reports 0 Frequency selectivity characterization report Major group indication (applicable to PUSC zone only) MIMO permutation feedback cycle (applicable to MIMO only)... RSSI Measurement..8, 8..., 8... and , 8..., 8... and , 8..., 8... and , 8... and , 8... and oi This option provides capability to the to report MCS preference to BS. oi Y Y This option provides capability to the to report MCS preference to BS. Also refer [] oi This option provides capability to the to report MCS preference to BS. o This feature only addresses two concurrent CQI channels reporting Effective CIR measurements. o 8... o IO-BF Y 8... o IO- MIMO Y Table. RSSI Measurement RSSI Measurement 8... and...0 m /A Y Processing of RSSI Page - 9

30 ..8 Modulation..8. PRBS (Subcarrier Randomization) measurements in the BS is specified in Section Table 8. PRBS PRBS m Y Y..8. Downlink Table 9. Downlink Modulation QPSK m Y Y -QAM m Y Y -QAM o Y Y..8. Uplink Table 0. Uplink Modulation QPSK m Y Y -QAM m Y Y -QAM o..8. Pilot Modulation Table. Pilot Modulation Pilot Modulation m Y Y Page - 0

31 ..8. Preamble Modulation Table. Preamble Modulation Preamble Modulation m Y /A shall demodulate the preamble..8. Ranging Modulation Table. Ranging Modulation 8 9 Ranging Modulation 8... m /A Y BS shall demodulate the ranging signal...9 MAP Support..9. ormal MAP 0 Table. ormal MAP ormal MAP... and Compressed MAP m Y Y Table. Compressed MAP Compressed MAP 8... po Y Y..9. Sub-DL-UL MAP Table. Sub-DL-UL MAP Page -

32 Sub-DL-UL MAP...0 o Y Y See.8... OFDMA MAP Capability of []. Support for Extended HARQ IE in ormal MAP mandates a support for Sub MAP for first zone. Also refer []..9. H-ARQ MAP Message Table. H_ARQ MAP Message Compact DL-MAP IE... o Compact UL-MAP IE... o..9. Extended HARQ IE in the ormal MAP Table 8. Extended H-ARQ IE in ormal MAP 8 9 Extended HARQ IE in the ormal MAP..9. DL Region Definition 8... & 8... & 8... & 8... o Y Y 0 Table 9. DL Region Definition Support DL Region Definition Support..0 AAS 8..., 8...,.8... o Page -

33 ..0. AAS Zone Support Table 0. AAS Zone Support DL AAS Zone 8... o UL AAS Zone 8... o..0. Supported Permutation in DL Table. Supported Permutation in DL PUSC 8... and 8... FUSC 8... and 8... Optional PUSC 8... and 8... AMC x 8... and 8... TUSC 8... and 8... TUSC 8... and Supported Permutation in UL oi Support for all the items in this table is conditional to the support of DL AAS Zone. oi oi oi oi oi Table. Supported Permutation in UL PUSC 8... and 8... Optional PUSC 8... and 8... oi Support for all the items in this table is conditional to the support of AAS Zone. oi Page -

34 AMC x 8... and 8... oi..0. AAS DL Preamble Table. AAS DL Preamble Frequency shifted 8... o Time shifted 8... o PHY Modifier 8... o DL AAS Preamble Support..0. AAS UL Preamble 8... o Support for 0- symbols Table. AAS UL Preamble 8 9 Frequency shifted 8... o Time shifted 8... o Physical Modifier 8... o UL AAS Preamble 8... o Power Control UL AAS Preamble Support..0. Diversity MAP Scan 8... o Support for 0- symbols Table. Diversity MAP Scan 0 Diversity-Map Scan 8... o..0. DL AAS-SDMA Pilots Table. DL AAS-SDMA Pilots AMC AAS-SDMA 8... o with All SDMA Pilots PUSC AAS-SDMA o Page -

35 TUSC AAS- SDMA TUSC AAS- SDMA AMC AAS-SDMA with SDMA pilots A&B only..0.8 UL AAS-SDMA Pilots 8... o 8... o 8... o Table. UL AAS_SDMA Pilots AMC AAS-SDMA 8... o with All SDMA Pilots PUSC AAS-SDMA o Optional PUSC o AAS-SDMA AMC AAS-SDMA 8... o with SDMA pilots A&B only..0.9 AAS Private MAP Table 8. AAS Private MAP 8 9 AAS Private MAP 8... o Reduced Private o MAP Reduced Private MAP Chain Support o..0.0 AAS-FBCK-REQ/RSP support Table 9. AAS_FBCK/RSP Support 0 AAS-FBCK-REQ/RSP support.. STC/MIMO 8... o Page -

36 ... Supported Features for DL PUSC Table 0. Supported Features for DL PUSC FHDC o -antenna, matrix A o IO MIMO Y -antenna, matrix B, o IOvertical encoding MIMO Y -antenna, matrix B, o horizontal encoding -antenna enhancement using directivity o -antenna, matrix A o antenna, matrix B, o vertical encoding 8 -antenna, matrix B, o horizontal encoding 9 -antenna, matrix C, o vertical encoding 0 -antenna, matrix C, o horizontal encoding... Supported Features for DL FUSC Table. Supported Features for DL FUSC FHDC o -antenna, matrix A o antenna, matrix B, vertical o encoding -antenna, matrix B, o horizontal encoding -antenna enhancement using directivity o -antenna, matrix A o -antenna, matrix B, vertical encoding o 8 -antenna, matrix B, horizontal encoding o two modulation and coding modules Page -

37 9 -antenna, matrix C, vertical encoding 0 -antenna, matrix C, horizontal encoding o o... Supported Features for DL Optional FUSC Table. Supported Features for DL Optional FUSC -antenna, matrix A antenna, matrix B, vertical encoding -antenna, matrix B, horizontal encoding antenna, matrix C antenna, matrix A antenna, matrix B antenna, matrix C antenna, matrix A antenna, matrix B, vertical encoding 0 -antenna, matrix B, horizontal encoding o consecutive OFDMA symbols o o o o logical subcarriers over consecutive symbols o o o logical subcarriers over consecutive symbols o o Page -

38 -antenna, matrix C, vertical encoding -antenna, matrix C, horizontal encoding Supported Features for DL Optional AMC o o Table. Supported Features for DL Optional AMC -antenna, matrix A antenna, matrix B, vertical encoding -antenna, matrix B, horizontal encoding antenna, matrix C antenna, matrix A antenna, matrix B antenna, matrix C antenna, matrix A antenna, matrix B, vertical encoding 0 -antenna, matrix B, horizontal encoding o bins over OFDMA symbols o Figure i o Figure i o o adjacent subcarriers over consecutive symbols o o o adjacent subcarriers over consecutive symbols o o Page - 8

39 -antenna, matrix C, vertical encoding -antenna, matrix C, horizontal encoding Supported Features for DL PUSC-ASCA o o Table. Supported Features for DL PUSC-ASCA STC/MIMO for PUSC- ASCA... Supported Features in UL PUSC o Table. Supported Features in UL PUSC -antenna, matrix A o -antenna, matrix B, o vertical encoding -antenna, matrix B, o horizontal encoding pp. in [] 8 9 Collaborative SM for two with single transmit antenna Collaborative SM for two with two transmit antennas o o... Supported Features in UL Optional PUSC IO- MIMO Y Pilot pattern C and D defined in[] 0 Table. Supported Features in UL Optional PUSC -antenna, matrix A o consecutive slots Page - 9

40 -antenna, matrix B, vertical encoding -antenna, matrix B, horizontal encoding Collaborative SM for two with single transmit antenna Supported Features in UL Optional AMC o o o Table. Supported Features in UL Optional AMC -antenna, matrix A antenna, matrix B, vertical encoding -antenna, matrix B, horizontal encoding Collaborative SM for two with single transmit antenna...9 Closed-Loop MIMO o Same AMC pilots as in DL x format o o o Table 8. Closed-loop MIMO Antenna Grouping w/ Tx matrix A Antenna Grouping w/ Tx matrix B Antenna Selection w/ Tx matrix C Antenna Grouping w/ Tx matrix A Antenna Grouping w/ Tx matrix B , o Table 98 o o Table 98a Table f o Table 98 o Page - 0

41 Antenna Selection w/ Tx matrix C Codebook Based Precoding 8 Quantized Weight Feedback 9 Quantized Weight Feedback...0 MIMO Feedback , o Table 98a Table g , o o -bit CQICH o -bit CQICH Table 9. MIMO Feedback 8 Fast MIMO Feedback o (complex weights) w/ bits Mode Selection Feedback o w/ bits -bit MIMO Fast Feedback o Fast DL measurement feedback w/ more than one Rx antennas Fast MIMO Feedback (complex weights) w/ bits Mode Selection Feedback w/ bits... MIMO Midamble o IO-MIMO Y o o IO-MIMO Y Table 0. MIMO Midamble Tx o Tx o Tx o... MIMO Soft-Handover Based Macro-diversity 9 Table. MIMO Soft-Handover Macro-diversity Macro MIMO w/ o Page -

42 MIMO_in_another_BS_IE() Macro MIMO w/ Macro_MIMO_DL_Basic_IE()... H-ARQ Downlink Support for MIMO o Table. H-ARQ Downlink Support for MIMO MIMO DL Chase 8... o IO-MIMO Y MIMO DL Chase is applicable to CC, CTC or LDPC from the perspective of IEEE 80.. In this document, the feature is only used in CTC mode. MIMO DL IR 8... o w/ CTC MIMO DL IR for 8... o Convolutional Code MIMO DL STC 8... o... H-ARQ Uplink Support for MIMO Table. H-ARQ Uplink Support for MIMO MIMO UL Chase 8... o IO-MIMO Y MIMO DL Chase is applicable to CC, CTC or LDPC from the perspective of IEEE 80.. In this document, the feature is only used in CTC mode. MIMO UL IR 8... o MIMO UL IR for 8... o Convolutional Code MIMO UL STC o.. HO Support in PHY Page -

43 ... FBSS Table. Fast Base Station Switching Anchor BS Report for FBSS and 8... o Anchor BS CQI and switch indication via CQICH... MIMO Soft-handover based macro-diversity transmission Table. MIMO Soft-handover based macro-diversity transmission MIMO Soft-handover based macro-diversity transmission Support Macro Diversity Handover using DL soft combining Support Macro Diversity Handover using DL burst in another segment in PUSC mode Support anchor BS indication of DL data burst in active BS Support of active BS indication of DL data burst in anchor BS Support of CID translation between Anchor BS and Active BS... UL Macro diversity o 8... o 8... o 8... o 8... o 8... o 8 Table. UL Macro Diversity Page -

44 UL Macro diversity 8... o To be used with UL PUSC Burst Allocation in Other Segment IE Support of Macro 8... o Diversity Handover using UL transmission in another segment in PUSC mode Support of anchor BS o indication of UL data burst in active BS Support of active BS indication of UL data burst in anchor BS o. Performance/Fidelity Requirements.. Minimum Performance... SSTTG/SSRTG 8 Table. SSTTG/SSRTG Item Description Reference Status Values SSTTG 8... m Y 0 usec SSRTG 8... m Y 0 usec... Max DL Concurrent Bursts 9 0 Table 8. Maximum DL Concurrent Bursts Item Description Reference Status Values Max Concurrent 8... and m Y 0 Burst..8. Page -

45 ... Max Bursts in DL Subframe Table 9. Max Bursts in DL Subframe Item Description Reference Status Values Max Burst in 8... m Y Frame... Max umber of Zones in DL/UL Subframe Table 80. Max umber of Zones in DL and UL Subframes Item Description Reference Status Maximum numbers of zones UL Maximum numbers of zones DL Values Y The number is the same as the number of Zone Switch IEs plus Max 8 Y The number is the same as the number of Zone Switch IEs plus.... Measurement Processes and CQI Channels Table 8. Measurement Processes and CQI Channels Item Description Reference Status Values Maximum numbers Y of CQI Channels transmitted by an per frame Maximum number of Y Maximum number of CIR concurrent CIR measurement processes (for measurement physical or effective CIR) that processes are active concurrently. A CIR measurement process is active from the frame in which it was allocated by a CQICH_Alloc_IE() until the frame in which the last CQI periodic transmission is sent or in which the CQI was deallocated by the BS. Page -

46 ... Max H-ARQ Bursts in DL/UL Subframe Table 8. Max H-ARQ Bursts Item Description Reference Status Values Max Burst in 8..., o Y Category DL Subframe 8..., =, with H-ARQ.8... Category =, Category =, Category Max Burst in UL Subframe with H-ARQ 8..., 8...,.8... = o Y Category =, Category =, Category =, Category =.. Transmit Requirements ote: unless specified otherwise, requirement applies to both BS and. Status for the four categories is oi, i.e. support for values corresponding to one or more of the categories from the set shall be supported in correlation to the categories of Section... Table 8. Transmitter Requirements Item Requirement Reference Values Specified Values. BS Tx dynamic db Range. Tx dynamic 8... db Range. Tx power level min adjustment step 8... db db. Tx power level 8... min relative step ± 0. db ± 0. db accuracy. Spectral flatness 8... ± db for spectral lines from used/ to and + to used/ Within +/- db for spectral lines from used/ to used/ and +used/ to used/ ± db for spectral lines from used/ to and + to used/ Within +/- db for spectral lines from used/ to used/ and +used/ to used/. Power difference 8... between adjacent 0. db 0. db subcarriers Page -

47 Item Requirement Reference Values. BS Tx reference timing accuracy 8. Tx relative constellation error 8..., for BS and 8... for.. Receiver Requirements Specified Tx downlink radio frame shall be time-aligned with the pps timing pulse QPSK-/ -.0 db QPSK-/ QAM-/ QAM-/ QAM-/ (if -QAM supported) QAM-/ (if -QAM supported) QAM-/ (if -QAM supported) -8.0 db -0. db -.0 db -.0 db -8.0 db -0.0 db Table 8. Receiver Requirements Item Requirement Reference Values Specified Values usec -.0 db -8.0 db -0. db -.0 db -.0 db -8.0 db -0.0 db Values Page -

48 Item Requirement Reference Values. Min SR requirements for BER=0 - with CTC in AWG channel (The Min SR requirements are used along with Eq. 9b to define sensitivity specifications for CTC.) Specified 8... QPSK-/ with 0 bytes block size QPSK-/ with bytes block size QAM-/ with 0 bytes block size QAM-/ with bytes block size QAM-/ with bytes block size (if -QAM supported) Values.9 db. db 8. db. db.8 db QAM-/ with 8 bytes block size (if -QAM supported) QAM-/ with bytes block size (if -QAM supported).9 db 8 db. Rx max input level on-channel reception tolerance. BS Rx Max input level on-channel reception tolerance. Rx max input level on-channel damage tolerance. BS Rx Max input level on-channel damage tolerance. Min adjacent channel rejection at BER=0 - for db degradation C/I. Min alternate channel rejection at BER=0 - for db degradation C/I QAM-/ with 0 bytes block size (if 9.9 db -QAM supported) db -0 db dbm - dbm db 0 db dbm -0 dbm 8... QAM-/ QAM-/ (if - QAM supported) 8... QAM-/ QAM-/ (if - QAM supported) db db 0 db db db db 0 db db Page - 8

49 Item Requirement Reference Values 8. Implementation loss plus oise Figure" (db) value assumed for for deriving receiver minimum sensitivity (equation 9b) 9. "Implementation loss plus oise Figure" (db) value assumed for BS for deriving receiver minimum sensitivity (equation 9b) Specified 8... The min requirement for Implementation Loss and oise Figure in [] are and 8 db respectively The min requirement for Implementation Loss and oise Figure in [] are and 8 db respectively... Frequency and Time Synchronization Requirements Values db ote: Eq. 9b of [] shall be used for calculation of Rx sensitivity requirements where min SR values for CC are given in Table 8 of [] and the min SR values for CTC mode are specified in the item of this table. db ote: Eq. 9b of [] shall be used for calculation of Rx sensitivity requirements where min SR values for CC are given in Table 8 of [] and the min SR values for CTC mode are specified in the item of this table. Table 8. Frequency and Time Synchronization Requirements Item Requirement Reference Values Values Specified. UL symbol timing accuracy. BS reference frequency accuracy. BS to BS frequency synchronization accuracy for Hand Over ± (Tb/8)/ ± (Tb/)/ This requirement includes only the timing error due to component and not the effect of inaccuracy of the BS ranging feedback ±*0 - ±* % of OFDMA carrier spacing % of OFDMA subcarrier spacing Page - 9

50 . to BS frequency synchronization tolerance 8... % of the subcarrier spacing % of the subcarrier spacing Page - 0

51 . MAC Profile. Profiles of BS and.. PHS Table 8. PHS PHS CS Options o Y Y Item Description Reference Statu s Table 8. Convergence Sublayer Options BS. Packet, IPv..,..9 oi Y Y. Packet, IPv..,..9 oi Y Y. Packet, 80./Ethernet..,..9 oi IO-ETH * * For, not required for WiMAX certified label, only optionally certified. Packet, 80.Q..,..9 oi VLA. Packet, IPv over 80./Ethernet. Packet, IPv over 80./Ethernet..,..9 oi IO-ETH * * For, not required for WiMAX certified label, only optionally certified..,..9 oi IO-ETH * * For, not required for WiMAX certified label, only optionally certified..,..9 oi. Packet, IPv over 80.Q VLA 8. Packet, IPv over..,..9 oi 80.Q VLA 9. ATM..,..9 oi Page -

52 Item Description Reference Statu s BS 0. Packet, IPv with Header Compression (ROHC). Packet, IPv with Header Compression (ECRTP). Packet, IPv with Header Compression (ROHC). Packet, IPv with Header Compression (ECRTP). Packet, IPv over 80./Ethernet with Header Compression (ROHC). Packet, IPv over 80./Ethernet with Header Compression (ECRTP). Packet, IPv over 80./Ethernet with Header Compression (ROHC). Packet, IPv over 80./Ethernet with Header Compression (ECRTP) 8. Packet, IPv over 80.Q VLA with Header Compression (ROHC) 9. Packet, IPv over 80.Q VLA with Header Compression (ECRTP)..,..9 oi Y Y..,..9 oi..,..9 oi Y Y..,..9 oi..,..9 oi..,..9 oi..,..9 oi..,..9 oi..,..9 oi..,..9 oi Page -

53 Item Description Reference Statu s BS 0. Packet, IPv over..,..9 oi 80.Q VLA with Header Compression (ROHC). Packet, IPv over 80.Q VLA with Header Compression (ECRTP)..,..9 oi ote: At least one of options shall be implemented... MAC PDU formats Table 88. MAC PDU Formats Reassembly at Rx Fragmentation at Tx Packing of fixedlength MAC SDUs Packing of variable-length MAC SDUs at Packing ARQ Feedback Payload Extended subheader support...,......,......,......,... m Y Y m Y Y Capability is mandatory. o o /A Y Unpacking is mandatory. Refer o Y Y ARQ Feedback Payload is treated like any other payload (Refer to... of []) Unpacking of ARQ Feedback Payload is mandatory if ARQ implemented/enabled at the connection...,.. o Y Y Extended subheader support is negotiated Page -

54 Capability of receiving bandwidth requests using Grant management Subheader... o Y /A 8 -bit FS support o See [] negotiated during SBC, bits is default.. MAC Support of PHY layer... Feedback Mechanism Table 89. Feedback Mechanism. Feedback Header... o Y Y. FAST-FEEDBACK... o allocation subheader. MIMO mode , o feedback extended subheader.... Feedback request... o extended subheader. Mini-Feedback... o extended subheader. Feedback Polling IE o Y Y. PHY channel report... o header 8. UL Tx Power Report... o extended subheader.. Multicast connection Table 90. Multicast Connection 8 9 Multicast traffic connection.. etwork Entry.. o Y Y Page -