Baureihen Series Séries U150R

Transcription

1 Baureihen Series Séries 150R Miniatur Radial Gebläse Miniature Radial Blower Ventilateur miniature radial SN EN ISO 9001 CERTIFICATED 150R-01KK-4 1 VDC 3600 Pa CFM VDC VDC 8 VDC VDC l/min R 150R-04KK-4 4 VDC 3600 Pa CFM VDC VDC 3 1 VDC 1 8 VDC VDC l/min R mm inch D Connector 3 gnd 1 vp vp 4 gnd Typ: Tyco V3535-A tacho 7 analog speed control 9 brake 10 dir 8 analog grd 6 nos / os D D3 ø 55 ø.170 L L L S ø 4.3 ø SW T1 ø 38 ø T T Z A4 150R 006 / 1000

2 Technische Daten Technical data Caractéristiques techniques Die 150R-Baureihe ist mit einem bürstenlosen Motor mit integrierter Elektronik ausgerüstet. The 150R-serie is equiped with brushless motor with integrated electronic. La série 150R est équipée avec un moteur brushless avec électronique intégrée. Flachmotor / Discmotor hohe Laufzeit integrierter Temperaturschutz (Motor) Tachosignal (Drehzahlrückmeldung) NOS (Non Operating Signal) analog speed control 4 V DC-Ausführung ohne Strombegrenzung flat motor / disc motor long operation time integrated temperature monitoring tacho signal (speed indicator) NOS (Non Operating Signal) analog speed control 4 V DC version without current limites moteur plat / moteur à disque long temps d'usage surveillance de température intégrée signal tacho (tachomètre) NOS (Non Operating Signal) analog speed control Execution 4 V sans limitation de courrent N I I N I I block P N V V A W n min ~1 n N min ~1 n min ~1 V l/min;cfm V l/min;cfm p Pa p Pa LpA db(a) MTTF hr T C/F m gr/oz. Lead Length mm Housing Material Sleeve Bearing Ball Bearing Tacho Signal Inlet Adapter Outlet Adapter Explosion Protection 150R-01KK R-04KK , / / / /1.0 15±15 (AWG 6) PPO L-94V / / / /1.0 15±15 (AWG 6) PPO L-94V-1 Freiblasend Prüfarbeitspunkt bei ca. 50% Luftmenge Druckerhöhung statisch Free blowing Inspection working point at approx. 50% air vol. Pressure difference static Refoulement libre Point de travail de contrôle appr.à 50% volume d air Différence de pression statique

3 Power supply requirements and Blower operating The power supply must limit the current according the absolute maximum ratings!!! Absolute maximum ratings 97DR 150R 1 V 4 V 1 V 4 V Blower voltage range Ripple < 5 % 8 16 V 1 7 V 8 16 V 1 7 V Power supply minimal current Current limit maximal at the power supply 3 ADC ADC 3 ADC 3 ADC 7 ADC 4 ADC 7 ADC 5 ADC Maximal Blower operating current.4 ADC.4 ADC.4 ADC.4 ADC* Blower locked rotor protection se of BRAKE function allowed yes no yes no yes no yes no * max. current ADC at 7 V The values are measured at 5 C / 77 F Exceeding the absolute maximum ratings may cause permanent damage.

4 Connector pre- connection External 470µF / 35 V capacitor is necessary Pin 1 and to 3 and 4 ( near the connector ) 97DR 4V: pre-connect Poly Switch Tyco RXE110 to Pin 1 /! Connector: notice arrow (Pin 1) VP 6 NOS VP 7 PWM 3 GND 8 AN. GND 4 GND 9 Brake 5 Tacho 10 nc Pin 1 / VP power supply positive potential Pin 1 and must be connected 470µF / 35 V capacitor is necessary Pin 1 and to 3 and 4 Pin 3 / 4 GND power supply ground potential Pin 3 and 4 must be connected Pin 5 Tacho Open drain output: pull-up resistor (kω) to 5V is integrated. (max. 10, no direct connection to GND and +VP) f Tacho [ Hz] * 5 = rpm [1/min] (8 pol. Motor) Supply voltage 5V Tacho Frequency 0.3 V

5 Pin 6 NOS Non Operating Signal Open drain output: pull-up resistor (kω) to 5V is integrated. (max. 10, no direct connection to GND and +VP) motor run: low motor blocked: high Supply voltage non rotating 5V 0.3 V rotating t Pin 7 PWM Analog speed control Input: 0 5 VDC Potentiometer 100kΩ to be connected with AN. GND (Pin 8). Adjustable ~10 100% PWM V5V PWM = 5V Motor = V5V * R PWMPoti (15 kω + R * 8.75 PWMpoti ) R 15 kω is integrated. ( pull-up resistor to 5V ) Motor = Pin PWM * 8.75 ( Independent of supply voltage ) Without Pin PWM connection: motor rotate with 100 % speed Pin 9 Brake At activated Brake signal, the motor is stopped immediately by shorting all driver outputs to ground. max = 5V ( rotate ) < 0.3 V = blocked Pin 10 nc please do not use max = 5V Caution - Handle connector only in currentless condition. - no polarity protection - power supply must limit the current! ( please see chart at page nr. 1 )