EC centrifugal fan G3G200-GN backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating.

Transcription

1 GG-GN- ebm-papst GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com Nominal data Type Motor GG-GN- MG8-DF Phase ~ Nominal voltage VAC Nominal voltage range VAC 8.. Frequency Hz 5/6 Type of data definition ml Speed min - 6 Power input W 89 Current draw 8 V Min. ambient temperature C - Max. ambient temperature C 5 Min. temp. of flow medium C Max. temp. of flow medium C 5 ml = max. load me = max. efficiency rfa = running at free air cs = customer specs cu = customer unit Subject to alterations Item no.: Revision: 686 Print-out 7// K. Boruzki (VI-I) Page of 5 ebm-papst Landshut GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com

2 GG-GN- Technical features Mass Size Surface of rotor Material of protective cover Material of impeller Housing material Number of blades 7 Direction of rotation 9. kg mm Type of protection IP Insulation class Max. permissible ambient motor temp. (transp./ storage) Min. permissible ambient motor temp. (transp./storage) Mounting position Condensate discharge holes Operation mode Motor bearing Technical features EMC interference immunity EMC interference emission Coated in black Polyflam RPP 7-ND CS (UL 97-V) Aluminium sheet Die-cast aluminium Clockwise, seen on rotor "B" +8 C - C Any Rotor-side S Ball bearing - Tach output - Over-temperature-protected electronics / motor - PFC, active - Motor current limit - Line undervoltage / phase failure detection - PWM control input - Control input - V Acc. to EN 6-6- (industrial environment) Acc. to EN 6-6- (industrial environment) EMC harmonics Acc. to EN 6--/ Leakage current Electrical leads Motor protection Protection class <=.5 ma With plug Locked-rotor protection Approval CSA C. Nr.; UL 57 I Item no.: Revision: 686 Print-out 7// K. Boruzki (VI-I) Page of 5 ebm-papst Landshut GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com

3 GG-GN- Product drawing Y Z Detail Y View Z / plug assignment -pole strip to fit mating connector (not included in standard scope of delivery) Tyco No , female connector Tyco No L. N. PE 5-pole strip to fit mating connector (not included in standard scope of delivery) Molex No. 9--5, female connector Molex No Speed monitoring. - VDC. PWM input.5 - Pressure tap optionally available Item no.: Revision: 686 Print-out 7// K. Boruzki (VI-I) Page of 5 ebm-papst Landshut GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com

4 GG-GN- Connection screen No. Pin Signal Function / assignment ST ; ; L; N; PE Power supply VAC, 5-6 Hz, phase, neutral, protective earth ST UB External voltage 6-5 VDC, residual ripple +/-.5%, SELV ST DUE Speed monitoring, pulses per revolution, SELV ST - V Control input - V, impedance k, SELV ST PWM Control input PWM, - 6 khz, SELV ST 5 GND GND - Connection for control interface, SELV Item no.: Revision: 686 Print-out 7// K. Boruzki (VI-I) Page of 5 ebm-papst Landshut GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com

5 GG-GN- Charts: Air flow 5 Hz Druck psf [Pa]für Rho=,kg/m^. qv[cfm] psf [Pa] ,5,5 9,5 9 8,5 8 7,5 7 6,5 6 5,5 5,5 psf_e[in HO] Measurement: LU-5 Air performance measured as per ISO 58 Installation category A. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 7 / LpA measured with m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed ,5, qv[m^/h] 8 9 psf [Pa]....,5,5. Measured values U f n P e I qv p sf V Hz min - W A m /h Pa Item no.: Revision: 686 Print-out 7// K. Boruzki (VI-I) Page 5 of 5 ebm-papst Landshut GmbH Hofmark-Aich-Str. 5 D-8 Landshut Phone Fax info@de.ebmpapst.com