EOLC-1HG-C-XX-YYC2. Copper CFP2 Cable Preliminary. Features. Applications. Ordering Information

Transcription

1 Copper CFP Cable Preliminary EOLC-1HG-C-XX-YYC CFP Cable Assemblies, 0.5m/1m/m/3m/4m Reach RoHS6 Compliant Features Supports Gb/s and 118.3Gb/s bit rates Lower Power Consumption for Single Module < 1.3W AWG up to 3 meters distance 6AWG up to 4 meters distance CDR Inside Power Supply: +3.3V Compatible to CFP MSA Temperature Range: 0~ 70 RoHS6 Compliant Applications 1G Ethernet OTU4 Ordering Information Part No. Data rate Per Lane Length AWG Passive/Active Temp EOLC-1HG-C-H-C Up to 7.95G 0.5m Active 0~ 70 EOLC-1HG-C-01-C Up to 7.95G 1m Active 0~ 70 EOLC-1HG-C-0-C Up to 7.95G m Active 0~ 70 EOLC-1HG-C-03-C Up to 7.95G 3m Active 0~ 70 EOLC-1HG-C-04-C Up to 7.95G 4m Active 0~ 70 EOLC-1HG-C-05-C Up to 7.95G 5m Active 0~ 70 Page 1 of 15

2 Regulatory Compliance* Note1 Copper CFP Cable Preliminary Product Certificate Certificate Number Applicable Standard TUV R EN :6+A11+A1+A1 UL E EMC CE AE UL CSA C. No EN 550:010 EN 5504:010 CB JPTUV IEC FCC WTF14F E 47 CFR PART 15 OCT., 013 ROHS RHS01G /65/EU Note1:The above certificate number updated to June 014, because some certificate will be updated every year, such as FCC and ROHS. For the latest certification information, please check with Eoptolink. Absolute Maximum Ratings* Note Parameter Symbol Min. Max. Unit Storage Temperature Ts C Supply Voltage Vcc V Operating Relative Humidity RH 5 85 % Note: Exceeding any one of these values may destroy the device immediately. Product Description EOLC-1HG-C-XX-YYC Copper Cable assemblies are high-performance, cost effective I/O solutions for 1 GB Ethernet and OTU4 applications. CFP copper modules allow hardware manufacturers to achieve high port density, configurability and utilization at a very low cost and to reduce power budget. Recommended Operating Conditions Parameter Symbol Min. Typical Max. Unit Operating Case Temperature T C EOLC-1HG-C-XX-YYC C Power Supply Voltage Vcc V Power Consumption* Note3 P 1.3 W Note3: The power consumption value is just depended on single module. Performance Specifications - Electrical Parameter Symbol Min. Typ. Max Unit Notes Input Amplitude (Differential) Input Impedance (Differential) Transmitter Vin 5 1 mvpp Zin ohms Page of 15 AC coupled inputs Rin > 1 DC

3 Copper CFP Cable Preliminary Output Amplitude (Differential) Output Impedance (Differential) Receiver Vout mvpp Zout ohms AC coupled outputs 1.V MDIO Interface Specifications Parameter Symbol Min. Typ. Max Unit Input Voltage V IH V V IL V Input Leak current I IN -1 1 ua Output Voltage V OH V V OL V Input Capacitance C I 10 pf Input MDC Clock f MDC MHz MDC Clock Period T MDC 50 1 ns MDIO Hold Time T hold 10 ns MDIO SetupTime T setup 10 ns GLB_ALM T glb_alm_ass 150 ms T glb_alm_dea 150 ms CFP Transceiver Electrical Pad Layout Pin Function Definitions CFP Bottom 1 GND 104 GND (TX_MCK_N) 103 N.C. 3 (TX_MCK_P) 10 N.C. 4 GND 101 GND 5 N.C. 1 TX3n 6 N.C. 99 TX3p 7 3.3V_GND 98 GND 8 3.3V_GND 97 TXn 9 3.3V 96 TXp Page 3 of 15 CFP Top

4 Copper CFP Cable Preliminary V 95 GND V 94 N.C V 93 N.C V_GND 9 GND V_GND 91 N.C. 15 VND_IO_A 90 N.C. 16 VND_IO_B 89 GND 17 PRG_CNTL1 88 TX1n 18 PRG_CNTL 87 TX1p 19 PRG_CNTL3 86 GND 0 PRG_ALRM1 85 TX0n 1 PRG_ALRM 84 TX0p PRG_ALRM3 83 GND 3 GND 8 N.C. 4 TX_DIS 81 N.C. 5 RX_LOS 80 GND 6 MOD_LOPWR 79 (REFCLKn) 7 MOD_ABS 78 (REFCLKp) 8 MOD_RSTn 77 GND 9 GLB_ALRMn 76 N.C. GND 75 N.C. 31 MDC 74 GND 3 MDIO 73 RX3n 33 PRTADR0 7 RX3p 34 PRTADR1 71 GND 35 PRTADR 70 RXn 36 VND_IO_C 69 RXp 37 VND_IO_D 68 GND 38 VND_IO_E 67 N.C V_GND 66 N.C V_GND 65 GND V 64 N.C V 63 N.C V 6 GND V 61 RX1n V_GND 60 RX1p V_GND 59 GND 47 N.C. 58 RX0n 48 N.C. 57 RX0p 49 GND 56 GND 50 (RX_MCK_N) 55 N.C. 51 (RX_MCK_P) 54 N.C. 5 GND 53 GND Page 4 of 15

5 Bottom Row Pin Descriptions Copper CFP Cable Preliminary Pin Num. Name Function Notes 1 GND (TX_MCK_N) O CML For optical waveform testing. Not for normal use. 3 (TX_MCK_P) O CML For optical waveform testing. Not for normal use. 4 GND 5 N.C. 6 N.C V_GND 8 3.3V_GND 9 3.3V V V 3.3V Module Supply Voltage 1 3.3V V_GND V_GND 15 VND_IO_A Module Vendor I/O A. Do not connect! 16 VND_IO_B Module Vendor I/O B. Do not connect! 17 PRG_CNTL1 Programmable control 1 set over MDIO, MSA default: TRXIC_RSTn. TX&RX ICs reset. 0 : reset; 1 or NC: enabled = not used. 18 PRG_CNTL Programmable Control set over MDIO, MSA Default: Hardware Interlock LSB, "": 3W, "01": 6W, "10": 9W, "11" or NC: 1W = not used 19 PRG_CNTL3 Programmable Control 3 set over MDIO, MSA Default: Hardware Interlock MSB, "": 3W, "01": 6W, "10": 9W, "11" or NC: 1W = not used 0 PRG_ALRM1 Programmable alarm 1 set over MDIO, MSA default: HIPWR_ON. 1 : module power up completed; 0 : module not high powered up. 1 PRG_ALRM Programmable alarm set over MDIO, MSA default: MOD_READY. 1 : ready; 0 : not ready. PRG_ALRM3 Programmable alarm 3 set over MDIO, MSA default: MOD_FAULT, fault detected. 1 : fault; 0 : not fault. 3 GND 4 TX_DIS I LVCMOS Transmitter disable for all lanes. 1 or NC: transmitter disabled; 0 : transmitter enabled. 5 RX_LOS O LVCMOS Receiver loss of optical signal. 1 : low optical signal; 0 : normal condition. 6 MOD_LOPWR I Module Low power mode. 1 or NC: module in low power LVCMOS (safe) mode; 0 : power-on enabled. Page 5 of 15

6 Copper CFP Cable Preliminary 7 MOD_ABS O GND Module Absent. 1 or NC: module absent; 0 : module present. Pull up resistor on Host. 8 MOD_RSTn I LVCMOS Module Reset. 0 : resets the module; 1 or NC: module enabled. Pull Down Resistor in module. 9 GLB_ALRMn O LVCMOS Global Alarm. 0 : alarm condition in any MDIO alarm register; 1 : no alarm condition. Open Drain, Pull up resistor on Host GND 31 MDC I 1.V CMOS Management Data Clock 3 MDIO I/O 1.V CMOS Management Data I/O bi-directional data 33 PRTADR0 I 1.V CMOS MDIO Physical Port address bit 0 34 PRTADR1 I 1.V CMOS MDIO Physical Port address bit 1 35 PRTADR I 1.V CMOS MDIO Physical Port address bit 36 VND_IO_C I/O Module Vendor I/O C. Do not connect! 37 VND_IO_D I/O Module Vendor I/O D. Do not connect! 38 VND_IO_E I/O Module Vendor I/O E. Do not connect! V_GND V_GND V 4 3.3V V 3.3V Module Supply Voltage V V_GND V_GND 47 N.C. No Connect 48 N.C. No Connect 49 GND 50 (RX_MCK_N) O CML For optical waveform testing. Not for normal use. 51 (RX_MCK_P) O CML For optical waveform testing. Not for normal use. 5 GND Top Row Pin Descriptions Pin Num. Name Function Notes 53 GND 54 N.C. 55 N.C. 56 GND 57 RX0p Lane 0 Rx Output 58 RX0n O CML Output 59 GND 60 RX1p Lane 1 Rx Output 61 RX1n O CML Output 6 GND Page 6 of 15

7 Copper CFP Cable Preliminary 63 N.C. 64 N.C. 65 GND 66 N.C. 67 N.C. 68 GND 69 RXp Lane Rx Output 70 RXn O CML Output 71 GND 7 RX3p Lane 3 Rx Output 73 RX3n O CML Output 74 GND 75 N.C. 76 N.C. 77 GND 78 (REFCLKn) Reference Clock 79 (REFCLKp) I Reference Clock Input 80 GND 81 N.C. 8 N.C. 83 GND 84 TX0p Lane 0 Tx Input 85 TX0n I CML Input 86 GND 87 TX1p Lane 1 Tx Input 88 TX1n I CML Input 89 GND 90 N.C. 91 N.C. 9 GND 93 N.C. 94 N.C. 95 GND 96 TXp Lane Tx Input 97 TXn I CML Input 98 GND 99 TX3p Lane 3 Tx Input 1 TX3n I CML Input 101 GND 10 N.C. 103 N.C. 104 GND Page 7 of 15

8 Copper CFP Cable Preliminary Memory Map EEPROM Definition EEPROM Address CFP NVR 1 Version V1.0 Field Data Size Addr (Byte) Name Of filed Description of field Coded value Hex BASE ID FIELDS 80h 1 Module Identifier Module Identifier CFP 11 81h 1 Extended Identifier Extended Identifier Power Class 1 Module ( 3W max),network lane : Host lane = Reserved,Non-WDM,No CLEI code present 8h 1 Connector Type Code Connector Type Code Undefined 83h 1 Ethernet Application Code Ethernet Application Code 1GE-CR4 Copper 1 84h 1 Fiber Channel Fiber Channel Application Application Code Code 85h 1 Copper Link Copper Link Application Application Code Code 86h 1 SONET/SDH SONET/SDH Application Application Code Code 87h 1 OTN Application Code OTN Application Code 88h 1 Additional Capable Additional Capable Rates Rates Supported Supported Gbps, Gbps 18 89h 1 Number of Lanes Number of Network Lanes:4; Number of Lanes Supported Supported Number of Host Lanes:4; 44 Media Type:Copper;Directionality:Norm 8Ah 1 Media Properties Media Properties al;without optical MUX/DEMUX;1 TX Lane and 1 RX Lane, C1 8Bh 1 Maximum Network Maximum Network Lane Bit Lane Bit Rate Rate 8Gbps 8C 8Ch 1 Maximum Host Lane Bit Rate Maximum Host Lane Bit Rate 8Gbps 8C 8Dh 1 Maximum Single Mode Optical Fiber Maximum Single Mode Optical Fiber Length Length 8Eh 1 Maximum Multi-Mode Optical Fiber Length Maximum Multi-Mode Optical Fiber Length Page 8 of 15

9 8Fh h h 1 Maximum Copper Cable Length Transmitter Spectral Characteristics 1 Transmitter Spectral Characteristics Copper CFP Cable Preliminary Maximum Copper Cable Length Transmitter Spectral Characteristics 1 Transmitter Spectral Characteristics 801h Minimum Wavelength Minimum Wavelength per 8013h per Active Fiber Active Fiber 8014h Maximum Wavelength Maximum Wavelength per 8015h per Active Fiber Active Fiber 8016h Maximum per Lane Maximum per Lane Optical 8017h Optical Width Width 8018h 1 Device Technology 1 Device Technology 1 Copper h 1 Device Technology Device Technology Page 9 of 15 x(m) No wavelength control,un-cooled transmitter device,transmitter not Tunable,Detector side VOA not implement,detector Type:Undefined;CDR without 801Ah 1 Signal Code Signal Code Undefined;Non-PSK 801Bh 1 801Ch 1 801Dh 1 801Eh 1 801Fh 1 800h 1 801h Maximum Total Optical Output Power per Connector Maximum Optical Input Power per Network Lane Maximum Power Consumption Maximum Power Consumption in Low Power Mode Maximum Operating Case Temp Range Minimum Operating Case Temp Range Maximum Total Optical Output Power per Connector Maximum Optical Input Power per Network Lane Maximum Power Consumption Maximum Power Consumption in Low Power Mode Maximum Operating Case Temp Range Minimum Operating Case Temp Range EDC xx 16mW 08 15mW 4B E 45 80h o 6F 803h p 70 8 Vendor Name Vendor Name 804h t h o 6F 806h l 6C

10 Copper CFP Cable Preliminary 807h i h n 6E 809h k 6B 80Ah <space> 0 80Bh <space> 0 80Ch <space> 0 80Dh <space> 0 80Eh <space> 0 80Fh <space> 0 80h <space> h 803h 3 Vendor OUI Vendor OUI 8033h 8034h E h O 4F 8036h L 4C 8037h C h h H Ah G Bh C Vendor Part Number Vendor Part Number 803Ch x xx 803Dh x xx 803Eh x xx 803Fh x xx 8040h C h 3 804h <space> h <space> h C h- 804Dh 16 Vendor Serial Number Vendor Serial Number x xx 804Eh- 8053h <space> h Year xx 8055h Year xx 8056h Year xx 8057h Year xx 8 Date Code Date Code 8058h Month xx 8059h Month xx 805Ah Day xx 805Bh Day xx 805Ch Lot Code Lot Code <space> 0 Page 10 of 15

11 Copper CFP Cable Preliminary 805Dh <space> 0 805Eh- 8067h 8068h h 1 10 CLEI Code CLEI Code CFP MSA Hardware Specification Revision Number CFP MSA Management Interface Specification Revision Number CFP MSA Hardware Specification Revision Number CFP MSA Management Interface Specification Revision Number Page 11 of 15 0 V1.4 0E V1.4 0E 806Ah Module Hardware Module Hardware Version 01 V Bh Version Number Number 806Ch Module Firmware Module Firmware Version 01 V Dh Version Number Number 806Eh 1 Digital Diagnostic Monitoring Type 806Fh h h 1 807h h 1 Digital Diagnostic Monitoring Capability Module Enhanced Options Maximum High-Power-up Time Maximum TX-Turn-on Time Digital Diagnostic Monitoring Type Digital Diagnostic Monitoring Capability 1 Digital Diagnostic Monitoring Capability Module Enhanced Options Maximum High-Power-up Time 60s Maximum TX-Turn-on Time 1s h 1 Host Lane Signal Spec Host Lane Signal Spec FF 8075h 1 Heat Sink Type Heat Sink Type Heat Sink Type:Flat top 8076h h h h 1 807Ah 1 807B- 807Eh Maximum TX-Turn-off Time Maximum High-Power-down Time Module Enhanced Options Transmitter Monitor Clock Options Receiver Monitor Clock Options Maximum TX-Turn-off Time 1ms 14 Maximum High-Power-down Time 3C 0s 01 Module Enhanced Options Transmitter Monitor Clock Options Receiver Monitor Clock Options 4 Reserved Reserved 807Fh 1 CFP NVR 1 Checksum CFP NVR 1 Checksum Note4 xx Note4: The check code shall be the 8 bit unsigned result of the checksum of all of the CFP register LSB contents from addresses 80h to 807Eh inclusive.

12 Copper CFP Cable Preliminary EEPROM Definition EEPROM Address CFP NVR 1 Version V1.0 Data Field Size Name Of filed Description of field Coded value Hex Addr (Byte) Alarm & Warning Thresholds 8080h 49 Temp High Alarm Temp High Alarm h 808h 46 Temp High Warning Temp High Warning h 8084h FB Temp Low Warning Temp Low Warning h 8086h F8 Temp Low Alarm Temp Low Alarm h 8088h 88 VCC High Alarm VCC High Alarm 3.5V 8089h B8 808Ah 84 VCC High Warning VCC High Warning 3.4V 808Bh D0 808Ch 7D VCC Low Warning VCC Low Warning 3.V 808Dh 808Eh 79 VCC Low Alarm VCC Low Alarm 3.1V 808Fh h SOA Bias Current High Alarm SOA Bias Current High Alarm N/A 8091h 809h SOA Bias Current High SOA Bias Current High Warning N/A 8093h Warning 8094h SOA Bias Current Low SOA Bias Current Low Warning N/A 8095h Warning 8096h SOA Bias Current Low Alarm SOA Bias Current Low Alarm N/A 8097h 8098h Auxiliary 1 Monitor High Auxiliary 1 Monitor High Alarm 8099h Alarm 809Ah Auxiliary 1 Monitor High Auxiliary 1 Monitor High Warning 809Bh Warning 809Ch Auxiliary 1 Monitor Low Auxiliary 1 Monitor Low Warning 809Dh Warning 809Eh Auxiliary 1 Monitor Low Auxiliary 1 Monitor Low Alarm 809Fh Alarm 80A0h Auxiliary Monitor High Auxiliary Monitor High Alarm 80A1h Alarm 80Ah Auxiliary Monitor High Auxiliary Monitor High Warning Page 1 of 15

13 Copper CFP Cable Preliminary 80A3h Warning 80A4h Auxiliary Monitor Low Auxiliary Monitor Low Warning 80A5h Warning 80A6h Auxiliary Monitor Low Auxiliary Monitor Low Alarm 80A7h Alarm 80A8h Laser Bias Current High Laser Bias Current High Alarm 80A9h Alarm 80AAh Laser Bias Current High Laser Bias Current High Warning 80ABh Warning 80ACh Laser Bias Current Low Laser Bias Current Low Warning 80ADh Warning 80AEh Laser Bias Current Low Laser Bias Current Low Alarm 80AFh Alarm 80B0h Laser Output Power High Laser Output Power High Alarm 80B1h Alarm 80Bh Laser Output Power High Laser Output Power High Warning 80B3h Warning 80B4h Laser Output Power Low Laser Output Power Low Warning 80B5h Warning 80B6h Laser Output Power Low Laser Output Power Low Alarm 80B7h Alarm 80B8h Laser Temperature High Laser Temperature High Alarm 80B9h Alarm 80BBh Laser Temperature High Laser Temperature High Warning 80BBh Warning 80BCh Laser Temperature Low Laser Temperature Low Warning 80BDh Warning 80BEh Laser Temperature Low Laser Temperature Low Alarm 80BFh Alarm 80C0h Receive Optical Power High Receive Optical Power High Alarm 80C1h Alarm 80Ch Receive Optical Power High Receive Optical Power High 80C3h Warning Warning 80C4h Receive Optical Power Low Receive Optical Power Low 80C5h Warning Warning 80C6h Receive Optical Power Low Receive Optical Power Low Alarm 80C7h Alarm 80C8-80F 55 Reserved E 80FF 1 CFP NVR Checksum Note5 xx Note5: The check code shall be the 8 bit unsigned result of the checksum of all of the CFP register LSB contents from addresses 8080h to 80FFh inclusive. Mechanical Specifications Page 13 of 15

14 Copper CFP Cable Preliminary CFP Obtaining Document You can visit our website: Or contact listed at the end of the documentation to get the latest documents. Page 14 of 15

15 Copper CFP Cable Preliminary Revision History Revision Initiated Reviewed Approved Revision History Release Date V1.a Picard Kelly/Torres/Marvin /Airon/Abby/Angela Preliminary. July, 015 Update regulatory V1.b Roty compliance and Picard /Marvin Modified power /Airon consumption maximum value NOV 03, 015 Marvin Angela Add picture and update the cable length. Oct Notice: Eoptolink reserves the right to make changes or discontinue any optical link product or service identified in this publication, without notice, in order to improve design and/or performance. Applications that are described herein for any of the optical link products are for illustrative purposes only. Eoptolink makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Contact: Add: Floor 5, Building, No. 1 Gaopeng Avenue, High-Tech District, CHENGDU, SICHUAN 6141 P.R. CHINA Tel: (+86) ext 816 or 809 Fax: (+86) Postal: sales@eoptolink.com Page 15 of 15