GPON ONU Series. EOLF-GU5-25-P Series. Features. Applications. Ordering Information. Case Temperature. Part No. Input Output Burst-mode Interface

Transcription

1 EOLF-GU5-25-P Series Class B+ ONU for GPON Single Fiber Bi-Directional WDM Transceiver 1.244Gbps Upstream and 2.488Gbps Downstream RoHS6 Compliant Features 2X5 SFF Package With SC Pigtail 1.244Gbps, 1310nm Burst Mode Transmitter 2.488Gbps, 1490nm Continuous Mode Receiver Un-cooled DFB Laser and APD High Sensitivity Detector Single 3.3V Power Supply LVTTL Tx_Dis, SD Class 1 FDA and IEC Laser Safety Compliant Operating Case Temperature Standard: 0 ~+70 Industry: -40 ~+85 Applications Access Networks GPON ONU Class B+ Fiber to the Home, Curb, Office (FTTx) Compliant with ITU-T G.984.2, G Amendent-2006, G Compliant with SFF MSA Specification Ordering Information Part No. Input Output Burst-mode Interface Case Temperature EOLF-GU5-25-P* note1 DC AC LVTTL Pigtail 0 ~+70 EOLF-GU5-25-IP DC AC LVTTL Pigtail -40 ~+85 Note1: Standard Version Page 1 of 9

2 Regulatory Compliance Product Certificate Certificate Number Applicable Standard TUV R EN :2006+A11+A1+A12 EN :2007 EN :2004+A1+A2 UL E UL CSA C22.2 No EMC CE AE EN 55022:2006 EN 55024:1998+A1+A2 CB JPTUV M1 IEC IEC FCC WTF13F E 47 CFR PART 15 OCT., 2010 WTF13F E 47 CFR PART 15 OCT., 2010 FDA CDRH ROHS RLSZF /65/EU Functional Diagram The Signal Detect (SD), Logic 1 represents the normal optical input level. The following versions are available: 1. DC/AC Transceiver Standard PECL inputs and CML outputs, TX is DC coupling and RX is AC coupling. Product Description Eoptolink s high performance GPON ONU transceiver is designed for passive optical network application. It can fully support the Class B+ ODN application specified by the ITU-T G standard and ITU-T G Amendent1. The GPON ONU transceiver is packaged of small form factor 2x5 with a pigtail connector. The module consists of 1310nm un-cooled DFB Laser, InGaAs preamplifier and WDM filter in a high-integrated optical sub-assembly. It transmits 1.244Gbps at 1310nm in burst mode and receives 2.488Gbps at 1490nm in continuous mode. Page 2 of 9

3 Absolute Maximum Ratings * Parameter Symbol Min. Max. Unit Storage Temperature T S C Supply Voltage V CC V Operating Relative Humidity - 95 % Wave Soldering Conditions Temp/Time - 260/10 C/s * Exceeding any one of these values may destroy the device immediately. Recommended Operating Conditions Parameter Symbol Min. Typical Max. Unit Operating Case Temperature T c EOLF-GU5-25-P 0-70 EOLF-GU5-25-IP Power Supply Voltage V CC V Power Supply Current I CC ma Date Rate Upstream/Downstream / Gbps Performance Specifications - Electrical Parameter Symbol Min. Typ. Max Unit Notes Transmitter Tx DC Supply Current Icc ma LVPECL Inputs(Differential) Input Impedance (Differential) Vin mvpp Zin ohm Tx_Dis Tx ON / Enable V IH 2 - Vcc+0.3 Tx Off / Disable V IL V Receiver Rx Supply Current Icc ma CML Outputs (Differential) Output Impedance RX_SD (Differential) Vout mvpp Zout ohm C DC coupled inputs Rin > 100 DC LVTTL, Control Input AC coupled outputs SD 2 - Vcc+0.3 V Assert High when LOSS V signal is detected Page 3 of 9

4 Performance Specifications - Optical Parameter Symbol Min. Typical Max. Unit Date Rate (Upstream/Downstream) R / Gbps Transmitter Centre Wavelength λ C nm -20dB Spectral Width Δλ nm Side Mode Suppression Ratio SMSR db Average Output Power * (Note2) Pout dbm Extinction Ratio* (Note3) ER db Rise/Fall Time (10%~90%) t R,t F ns Output Optical Eye* (Note4) ITU-T G984.2 Compliant Optical Burst On/ Off Time t_on/t_off ns Additive Jitter Generation J A UI Optical Output Power with TX OFF* (Note2) P_off dbm Transmitter and Dispersion Penalty TDP db Transmit Reflectance RFL db Optical Return Loss R L db Receiver Centre Wavelength λc nm Receiver Sensitivity* (Note5) Pmin dbm Saturation Optical Power Pmax dbm Damage Threshold P DT dbm Receiver Reflectance Rf db Polarization Dependent Loss PDL db 1555nm Rx to 1490nm Isolation db SD Assert SDA dbm SD De-Assert SDD dbm Signal Detect Hysteresis* (Note6) dbm G Wavelength Blocking Filter, 1530nm to1539nm G Wavelength Blocking Filter, 1540nm to 1625nm WBF db Note2: Measured with 9/125um G.652 SMF 25 case temperature. Note3: Filtered, measured with PRBS test Note4: Eye Pattern Mask. Page 4 of 9

5 Note5: Measured with a PRBS test and ER=10dB, BER 1X Note6: LOS Hysteresis(SD signal coincides with the LOS signal inversion) Transmitter Burst Mode Timing Characteristics VccT Burst control Data Input Optical Output VccT < 2.5V X X OFF VccT > 3.13V X means don t care. Low X OFF High/NC Other means peak power less than +8dBm. High/Low means Logic high/low level. NO Yes No means data not present, Yes means data present. OFF means the optical power less than -45dBm. Other Laser bias and modulation signal output Page 5 of 9

6 Burst transmitter timing SFF 2x5 Pin Function Definitions Tx/Rx Pin No. I/O Pin Name Description 1 VeeR Receiver Ground 2 VccR +3.3V Receiver Power Supply 3 O SD Normal Optical Input indicated by logic High, and No Optical Input indicated by logic Low. Rx Inverted Receiver Data Output, RD- output will be 4 O RD(n) muted when SD Low level. (AC-Coupled internally and CML 50Ω Terminated) 5 O RD(p) Non-Inverted Receiver Data Output, RD+ output will be muted when SD Low level. (AC-Coupled internally and CML 50Ω Terminated) 6 VccT +3.3V Transmitter Power Supply* (Note7) 7 VeeT Transmitter Ground Tx 8 I Tx_DIS Default LVTTL Logic High to Enable Burst Transmitter, Disable Burst Transmitter by Logic Low. 9 I TD(p) Non-Inverted Transmitter Data Input (DC-Coupled) Internally 100R terminated between TD(p) and TD(n) 10 I TD(n) Inverted Transmitter Data Input (DC-Coupled) Internally 100R terminated between TD(p) and TD(n) F Mounting Studs/Connect this pin to Chassis ground Note7: VccR is not connected with VccT in the module. When VccT is turned off, the transmitter stops to work. Page 6 of 9

7 The following figure illustrates the SFF 2x5 pin arrangement. SC Pigtail Pin arrangement (Top View) Recommended Circuit Schematic 2x5 DC/AC Coupling Note A: Place Close to Serdes: R6/R7/ R8/R9 depending on the requirement of Serdes. Note B: CML output, AC coupled internally. Input stage in SerDes IC is assumed with high impedance and internal bias to Vcc-1.3V R1=R2=R3=R4=N.C, R5=100Ω Input stage in SerDes IC is assumed without internal bias to Vcc-1.3V R1=R2=82Ω, R3=R4=130Ω, R5= N.C. Page 7 of 9

8 Mechanical Specifications Laser Emission Pigtail with SC Connector Obtaining Document You can visit our website: Or contact listed at the end of the documentation to get the latest documents. Revision History Revision Initiated Reviewed Approved Description Release Date Oliver/ Wlat/Lyn/ Philo Initial Nov. 06, 2013 Jans Nygai Page 8 of 9

9 Notice: Eoptolink reserves the right to make changes to or discontinue any optical link product or service identified in this publication, without notice, in order to improve design and/or performance. Applications that are described herein for any of the optical link products are for illustrative purposes only. Eoptolink makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Contact: Add: Floor 5, Building 2, No. 21 Gaopeng Avenue, High-Tech District, CHENGDU, SICHUAN P.R. CHINA Tel: (+86) ext 816 & 809 Fax: (+86) Postal: Page 9 of 9