SFP+ Dual LC 10G SMF 10Km 1310nm Transceiver. Features. Applications. Ordering Information APPLIED OPTOELECTRONICS, INC.

Transcription

1 Features Applications 10GBASE-LR Ethernet (9.95 to 10.31Gbps) CPRI 7 ( Mibit/s) CPRI 8 ( Mibit/s) SFP+ Type Dual LC Transceiver 1310nm DFB Laser PIN Photo Detector 10Km transmission with SMF 3.3V single power supply Compliant with SFP+ MSA Compliant with IEEE 802.3ae Hot pluggable Serial ID information support Digital diagnostic SFF-8472 compliant Compliant with RoHS Compliant with UL & TUV Compliant with SFF-8431 Ordering Information Form Factor Date Rate Media Distance Wavelength (nm) TX Power (dbm) RX Sensitivity (dbm) Voltage (V) Coupling Signal Detect DDM (Y/N) Temperature ( C) Part Number SFP-Dual-LC 10G SMF 10Km ~ -8.2 < AC/AC TTL Y -40 ~ +90 Page 1 of 10

2 Absolute Maximum Ratings Parameter Symbol Conditions Min Max Unit Storage Temperature T S C Storage Relative Humidity RH % Supply Voltage V CC V Recommended Operating Conditions Parameter Symbol Conditions Min Typ Max Unit Operating Temperature (Case) T C C Supply Voltage V CC V Supply Current I TX +I RX ma Data Rate DR Gbps Electrical Characteristics Parameter Symbol Conditions Min Typ Max Unit Transmitter Differential Input Impedance R DI Ohm Differential Input Voltage V DI AC-Coupled, peak to peak mv Tx Disable Input-High V DISH V CC+0.3 V Tx Disable Input-Low V DISL V Tx Fault Output-High V FOH V CC+0.3 V Tx Fault Output-Low V FOL V Receiver Differential Output Impedance R DO Ohm Differential Output Voltage V DO AC-Coupled, peak to peak mv Rx LOS Output-High V LOSH V CC+0.3 V Rx LOS Output-Low V LOSL V Optical Characteristics (Vcc=3.14V to 3.46V, 9/125um SMF) Parameter Symbol Conditions Min Typ Max Unit Transmitter Optical Center Wavelength λc nm Spectral Width (-20) nm Optical Output Power P o (Avg.) dbm Optical Extinction Ratio ER db Side Mode Suppression Ratio SMSR db Optical Modulation Amplitude OMA dbm Relative Intensity Noise RIN 12OMA db/hz Eye Mask -- Compliant with IEEE 802.3ae Receiver Operating Wavelength λ nm Receiver Overload P INMAX dbm Rx Sensitivity P INMIN dbm Rx Sensitivity P INMIN dbm Rx LOS Assert LOS A dbm Rx LOS De-Assert LOS D dbm Rx LOS Hysteresis db Receiver Reflectance db 1. Measured with PRBS at BER Page 2 of 10

3 Pin Description SFP+ Transceiver Electric Pad Layout SFP+ Transceiver Host PCB PAD Assignment Page 3 of 10

4 Pin Function Definitions Pin No. Pin Name Function/Description Power Sequence Order Note 1 VeeT Transmitter Ground 1st 1 2 Tx_Fault Transmitter Fault 3rd 2 3 Tx_Disable Transmitter Disable; Turns off transmitter laser output 3rd 3 4 SDA 2-wire Serial Interface Data Line (MOD-DEF2) 3rd 5 SCL 2-wire Serial Interface Clock (MOD-DEF1) 3rd 6 Mod_ABS Module Absent, connected to VeeT or VeeR in the module 3rd 4 7 RS0 Rate Select 0, (not functional) 3rd 8 Rx_LOS Receiver Loss of Signal Indication 3rd 2 9 RS1 Rate Select 1, (not functional) 3rd 10 VeeR Receiver Ground 1st 1 11 VeeR Receiver Ground 1st 1 12 RD- Receiver Inverted Data Output 3rd 13 RD+ Receiver Non-Inverted Data Output 3rd 14 VeeR Module Receiver Ground 1st 1 15 VccR Receiver 3.3 V Supply 2nd 16 VccT Transmitter 3.3 V Supply 2nd 17 VeeT Transmitter Ground 1st 1 18 TD+ Transmitter Non-Inverted Data Input 3rd 19 TD- Transmitter Inverted Data Input 3rd 20 VeeT Transmitter Ground 1st 1 Notes: 1. The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 2. This contact is an open collector/drain output contact and shall be pulled up with a 4.7k to 10k Ohms resistor to host_vcc on the host board. Pull ups can be connected to one of several power supplies, however the host board design shall ensure that no module contact has voltage exceeding module VccT/R V. 3. This contact is an input contact with a 4.7 kω to 10k Ohms pull up to VccT inside the module. 4. This contact shall be pulled up with a 4.7k to 10k Ohms resistor to host_vcc on the host board. Page 4 of 10

5 Mechanical Design Diagram Page 5 of 10

6 Specific EEPROM Memory Contents Page A0h AOI E Add Name of field ACSII HEX 0 Identifier 03:SFP Transceiver 03 1 Ext. Identifier 04:SFP Transceiver 04 2 Connector 07:LC G Ethernet 20:10G Base-LR 20 4 SONET/SDH 00 5 SONET/SDH 00 6 Ethernet 00 Transceiver 7 Fiber Channel 00 8 Fiber Channel 00 9 Fiber Channel Fiber Channel Encoding 01:8B10B, 03:NRZ, 05:SONET, 06:64B/66B, BR, Nominal 100Mbps/unit -> HEX 67:10.3G Reserved Reserved Length(9um, km) 1km /unit -> HEX 0A :10KM 0A 15 Length (9um) 100m /unit -> HEX 64:10000M Length (50um), OM2 10m /unit -> HEX Length (62.5um), OM1 10m /unit -> HEX Length (Copper) 1m /unit -> HEX Length (50 um), OM3 10m /unit -> HEX A O 4F 22 I Vendor name SFP Vendor Name (ASCII) Page 6 of 10

7 36 Reserved Reserved Vendor OUI SFP Vendor IEEE company ID, No ID set "00" A E L 4C 44 L 4C 45 N 4E 46 D Vendor PN SFP Vendor Part Number (ASCII) 48 A D O 4F 51 A B 42 Hardware Revision (HEX) Ver B Vendor rev Firmware Revision (HEX) V Wavelength Wavelength -> HEX (051E: 1310nm) 61 1E 62 Reserved CC_BASE Check Sum 0 to 62 byte Options 18:TX-DIS,TX_Fault 1A:TX-DIS,TX_Fault,RX-LOS 66 BR, max 1% /unit BR, min 1% /unit A 68 XX 69 XX 70 XX 71 Vendor SN Vendor SN (ASCII) XX 72 XX 73 XX 74 XX Page 7 of 10

8 75 XX 76 XX 77 XX 78 XX 79 XX 80 XX 81 XX 82 XX 83 XX 84 XX Year (ASCII) 85 XX 86 XX Month (ASCII) 87 XX Date code 88 XX Day (ASCII) 89 XX Blank Diagnostic Monitoring Type 93 Enhanced Options 58:W/I DDM(Ext_Cal), 68:W/I DDM(Int_Cal) E0:A/W, Tx_Dis, Tx_fault F0:A/W, Tx_Dis, Tx_fault, Rx_LOS B0:A/W, Tx_fault, Rx_LOS 94 SFF-8472 Compliance 01:9.3, 02:9.5, 03:10.2, 04:10.4, 05:11.0, 06: CC_EXT Check Sum 64 to 94 byte XX 68 F Read-only Read-only Page 8 of 10

9 Page 9 of 10

10 Regulatory Compliance Item Electromagnetic Interference (EMI) Standard FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B MIL-STD-883E Method Electrostatic Discharge to the Electrical Pins (ESD) Electrostatic Discharge to the Receptacle (ESD) IEC RoHS 2011/65/EU Laser Eye Safety FDA 21CFR and Component Recognition UL and TUV Laser Safety Information All versions of this laser are Class 1 laser products per IEC 1 /EN Users should observe safety precautions such as those recommended by ANSI 3 Z136.1, ANSI Z36.2 and IEC This product conforms to FDA (CDRH) 21 CFR and except for deviations of laser safety class designation pursuant to 'Laser Notice No.50' Product labeling: Class 1 Laser Product Compliance with 21 CFR and If labeling is not affixed to the module due to size constraints; then rather, labeling is placed on the outside of the shipping box. This product is not shipped with a power supply. Caution: use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Certifications UL (E243407) TUV EN , EN , EN Documentation is available upon request. (1) IEC is a registered trademark of the International Electro technical Commission (2) Within Europe the IEC standard has been adopted as a European Normative standard known as EN 60825, and each European country will have its own version of this standard, for example, the British Standards version known as BS EN There can be small differences between the different countries versions of EN 60825, and these are in part caused by the process of translating the standard into the native language of that country. (3) ANSI is a registered trademark of the American National Standards Institute Note : All information contained in this document is subject to change without notice. Page 10 of 10