XFP Series. Applications. Data Rate. Laser. EOLX-1696-TDW-14XXX1 8.5~11.35G MZM SMF 14dB

Transcription

1 EOLX-1696-TDW-14XXX series Single-Mode Tunable XFP Transceiver RoHS6 Compliant Features Available in all C-Band Wavelengths on the 50GHz DWDM ITU Grid Supports 8.5Gb/s to 11.35Gb/s bit Rates Hot-Pluggable XFP Footprint power budget >14dB Monolithic MZM Tunable TOSA High performance PIN Receiver Duplex LC Connector Built-in Digital Diagnostic Functions Temperature Range: -5 C to 70 C Applications DWDM 10Gb/s SONET/SDH DWDM 10Gb/s Ethernet & 10Gb/s Fibre Channel DWDM 10Gb/s SONET/SDH w/fec DWDM 10Gb/s Ethernet and 10Gb/s Fibre Channel w/fec Ordering Information Part No. Data Rate Laser Fiber Type Power budget EOLX-1696-TDW-14XXX* note1 8.5~11.35G MZM SMF 14dB EOLX-1696-TDW-14XXX1 8.5~11.35G MZM SMF 14dB Performance Standard Performance High performance Note1: XXX refers to the default DWDM Wavelength channel as ITU-T specified, listing in the following table in detailed. Page 1 of 13

2 DWDM Wavelength List: *Channel (X) Part NO. Frequency (THz) Center Wavelength (nm) 170 EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW Page 2 of 13

3 365 EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW Page 3 of 13

4 580 EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW EOLX-1696-TDW *: The wavelength is default while manufacture, please contact EOPOTLINK while ordering. Regulatory Compliance XFP Series Product Certificate Certificate Number Applicable Standard EN :2006+A11+A1+A12 TUV UL R E EMC CE AE CB FCC JPTUV M1 EN :2007 EN :2004+A1+A2 UL CSA C22.2 No EN 55022:2006 EN 55024:1998+A1+A2 IEC IEC WTF13F E 47 CFR PART 15 OCT., 2010 WTF13F E 47 CFR PART 15 OCT., 2010 FDA CDRH ROHS RLSZF /65/EU Absolute Maximum Ratings Parameter Symbol Min Typ. Max Unit Maximum Supply Voltage 1 Vcc V Maximum Supply Voltage 2 Vcc V Storage Temperature T S C Maximum Input Power Pm 0.5 dbm Recommend Operating Condition Parameter Symbol Min Typ. Max Units Operating Temperature Tc C Supply Voltage 1 Vcc V Supply Voltage 2 Vcc V Electrical Characteristics Parameter Symbol Min Typ Max Unit Page 4 of 13

5 Main Supply Voltage Vcc V Supply Voltage #2 Vcc V Supply Current Vcc5 supply Icc5 500 ma Supply Current Vcc3 supply Icc3 750 ma Module Total Power P 3.5 W Transmitter Input Differential Impedance Rin 100 Ω Differential Data Input Swing *note2 Vin, pp mv Transmit Disable Voltage VD 2.0 Vcc V Transmit Enable Voltage VEN GND GND+ 0.8 V Transmit Disable Assert Time 10 us Receiver Differential Data Output Swing *note2 Vout, pp mv Rise Time (20~80%) tr 38 ps Fall Time (20~80%) tf 39 ps LOS Fault *note3 VLOS fault Vcc 0.5 Vcc_Host LOS Normal *note3 VLOS norm GND GND+0.5 V Note2. After internal AC coupling. Note3. Loss of signal is open collector to be pulled up with a 4.7k 10kohm resistor to V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. Optical Characteristics Parameter Symbol Min Typ Max Unit Transmitter Output Opt. Pwr: 9/125 SMF Pout dbm Center Wavelength Spacing V 50 GHz 0.4 nm Transmitter Center Wavelength BOL λ C X-20 X X+20 pm Optical Extinction Ratio ER db Transmitter and Dispersion Penalty TDP 2 db Average Launch Power of OFF transmitter POFF -30 dbm TX Jitter (SONET) 20kHz-80MHz TXj1 0.3 UI TX Jitter (SONET) 4MHz-80MHz TXj2 0.1 UI Receiver Maximum Input Power Pmax 0 dbm Optical Center Wavelength λ C nm LOS De-Assert LOSD -17 dbm LOS Assert LOSA -29 dbm LOS Hysteresis 0.5 db EOLX-1696-TDW-14XXX Page 5 of 13

6 Receiver Sensitivity XFP Series Datarate (Gb/s) BER dispersion (ps/nm) sensitivity B-B at OSNR>30dB (dbm) Dispersion penalty at OSNR>30dB (dbm) Threshold adjust request E to No E to No E to YES E to YES OSNR performance Min OSNR B-B Max OSNR penalty Datarate dispersion Threshold BER at power: at power: (Gb/s) (ps/nm) adjust request -14~-2dBm(dB) -14~-2dBm(dB) E to No E to No E to YES E to YES EOLX-1696-TDW-14XXX1 Receiver Sensitivity sensitivity B-B Dispersion penalty Datarate dispersion Threshold BER at OSNR>30dB at OSNR>30dB (Gb/s) (ps/nm) adjust request (dbm) (dbm) E to No E to No E to YES E to YES E to YES OSNR performance Min OSNR B-B Max OSNR penalty Datarate dispersion Threshold BER at power: at power: (Gb/s) (ps/nm) adjust request -14~-2dBm(dB) -14~-2dBm(dB) E to No E to No E to YES E to YES E to YES Pinout arrangement Page 6 of 13

7 Pin Descriptions Pin Symbol Name/Description Note 1 GND Module Ground 4 2 VEE5 Optional 5.2 Power Supply Not required 3 Mod-Desel Module De-select; When held low allows the module to respond to 2-wire serial interface commands 4 Interrupt Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface 5 TX_DIS Transmitter Disable; Transmitter laser source turned off 6 VCC5 +5 Power Supply 7 GND Module Ground 4 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 SCL Serial 2-wire interface clock line 5 11 SDA Serial 2-wire interface data line 5 12 Mod_Abs Module Absent; Indicates module is not present. Grounded in the module. 13 Mod_NR Module Not Ready; 5 14 RX_LOS Receiver Loss of Signal indicator 5 15 GND Module Ground 4 16 GND Module Ground 4 17 RD- Receiver inverted data output 18 RD+ Receiver non-inverted data output 5 5 Page 7 of 13

8 19 GND Module Ground 4 20 VCC2 +1.8V Power Supply Not required Power Down; When high, places the module in the low power 21 stand-by mode and on the falling edge of P_Down initiates a P_Down/RS module reset T Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 VCC2 +1.8V Power Supply Not required 23 GND Module Ground 4 24 RefCLK+ Reference Clock non-inverted input, AC coupled on the host 6 board Not required 25 RefCLK- Reference Clock inverted input, AC coupled on the host board 6 Not required 26 GND Module Ground 4 27 GND Module Ground 4 28 TD- Transmitter inverted data input 29 TD+ Transmitter non-inverted data input 30 GND Module Ground 4 Note4. Module circuit ground is isolated from module chassis ground within the module. Note5. Open collector; should be pulled up with 4.7k 10k ohm on host board to a voltage between 3.15Vand 3.6V. Note6. A Reference Clock input is not required. General Specifications Parameter Symbol Min Typ Max Units Note Bit Rate BR Gb/s 8 Max. Supported Link Budget LMAX db Note8. SONET OC-192, SONET OC-192 with FEC, 10G Ethernet with FEC, 10G Fiber Channel with FEC, 10G Ethernet Digital Diagnostic Functions Eoptolink s EOLX-1696-TDW-14XXX Small Form Factor 10Gbps (XFP) transceivers are compliant with the current XFP Multi-Source Agreement (MSA) Specification Rev 4.5. As defined by the XFP MSA, Eoptolink XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: Transceiver temperature Laser bias current Transmitted optical power Received optical power Page 8 of 13

9 Transceiver supply voltage TEC Temperature It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. Tuning Management Interface for ITU Frequency Grid Application Implementation of wavelength or frequency tuning is indicated in Serial ID Byte 221(Table 01h) bit1. Data Address Bit Description 221 (Table 01h) 1 Wavelength orfrequency tunability implemented The Eoptolink tunable XFP supports wavelength and frequency tuning (as specified in INF-8077i), the wavelength tuning support is indicated by the transceiver description encoded in Serial ID Byte 138 bits 2 and 3. Address Bit Description of transceiver Tunable DWDM(selection by Channel number,bytes ) Tunable DWDM(selection in 50pm steps,bytes 72-73) Reserved Upon a power up, the module will go to a default wavelength or the last channel set by the host. If Tx_DIS is asserted upon power up, the laser will be disabled and the set wavelength will be cleared. Once the Tx_DIS is de- asserted, the firmware will maintain the laser in an off state until the host sets the desired ITU channel. If the module is powered-down before the ITU channel was set and TX_DIS de-asserted, the module will re-start at the default channel. A desired wavelength can be commanded by the user by writing into Bytes 72(MSB)and 73 (LSB). Wavelength control command: Address Bit Name Description 72(MSB)&73(LSB) All Wavelength Set User input of Wavelength set point(in units of Page 9 of 13

10 50pm) XFP Series 74(MSB)&75(LSB) All Wavelength Error Monitor of Current Wavelength Error(in units of 5pm) Thus for instance a target wavelength of nm would correspond to 79h (MSB) written to Byte address 72 and 9Bh(LSB) written to Byte address 73. A desired frequency Channel can be commanded by the user by writing into Bytes 112(MSB) and 113(LSB). Address Bit Name Description 112(MSB)&113(LSB) All Wavelength Set User input of channel number, which is an integer 1 to N (N=Number of Channel) 114(MSB)&115(LSB) All Wavelength Error Frequenvy error reported in 16 bit signed All Reserved Reserved integer with LSB=0.1HGHz *Note: the channel bunmer is derived from the following equation using parameters found in Module capabilities as listed in Byte Addresses 60-69: Channel number = 1+(Desried Frequency Frist Frequency)/Grid Spacing. Alarm and Warning Threshold Values Address Parameter Threshold Values UNITS Temp High Alarm 78 C Temp Low Alarm -13 C Temp High Warning 73 C Temp Low Warning -8 C Reserved Bias High Alarm 120 ma Bias Low Alarm 10 ma Bias High Warning 110 ma Bias Low Warning 15 ma TX Power High Alarm +5 dbm TX Power Low Alarm -3 dbm TX Power High Warning +4 dbm TX Power Low Warning -2 dbm RX Power High Alarm 1 dbm RX Power Low Alarm -18 dbm RX Power High Warning 0 dbm RX Power Low Warning -17 dbm AUX 1 High Alarm 57 C AUX 1 Low Alarm 20 C AUX 1 High Warning 54 C AUX 1 Low Warning 25 C AUX 2 High Alarm V AUX 2 Low Alarm V Page 10 of 13

11 54-55 AUX 2 High Warning V AUX 2 Low Warning V Digital Diagnostic Monitor Specification Address Parameter Accuracy Resolution Units Notes Module Case Temp +/-3 +/-0.1 C PCB mounted thermocouple Reserved TX bias current +/-8 +/-2 μa Transmit Power +/-1.5dB 0.1 μw Receive Power +/-1.5dB +/-0.1 μw Auxiliary monitor1 +/-3 +/-0.1 C Laser Temperature Auxiliary monitor2 +/-3 +/-100 μv 3.3V Supply Voltage Recommended Host Board Power Supply Circuit Recommended High-Speed Interface Circuit Page 11 of 13

12 Mechanical Specifications Eoptolink s XFP transceivers are compliant with the dimensions defined by the XFP Multi-Sourcing Agreement (MSA). Eye Safety This single-mode transceiver is a Class 1 laser product. It complies with IEC and FDA 21 CFR and The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. Obtaining Document You can visit our website: Or contact Listed at the end of the documentation to get the latest Page 12 of 13

13 documents. XFP Series Revision History Revision Initiated Reviewed Approved DCN Release Date V1.a Abby Kelly Release Mar 13, 2013 V1.b Angela Kelly Update product picture and mechanical spec. Apr 15,3013 Update regulatory V1.c Angela performance. Kelly/Walt/ compliance and October 16, Jason/Frank add OSNR 2013 V1.d Angela/Sky Kelly Add 170 and 615 channels Dec 04,2013 Angela Kelly Correct some slip of the pen. Mar 20,2014 Notice: Eoptolink reserves the right to make changes to or discontinue any optical link product or service identified in this publication, without notice, in order to improve design and/or performance. Applications that are described herein for any of the optical link products are for illustrative purposes only. Eoptolink makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Contact: Add: Floor 5, Building 2, No. 21 Gaopeng Avenue, High-Tech District, CHENGDU, SICHUAN P.R. CHINA Tel: (+86) ext 816 & 809 Fax: (+86) Postal: Page 13 of 13