celduc SILD r e l a i s celpac PATENTED! AC Semiconductor Contactor pitch 22,5mm with Diagnostic compact size and DIN rail mounting.

Transcription

1 AC Semiconductor Contactor pitch,5mm with Diagnostic compact size and DIN rail mounting. Ready to use SinglePhase Relay: " Install it & Forget it!" Zero cross model : 55VAC 5A back to back thyristors on output TMS technology I t value > 5A s I t values on request to 5 A s. Model with diagnostic : status of the SSR and the load. Normally closed status output. Without external power supply. Status visualization by yellow LED (*). Status output can be chained. Very high immunity : Voltage protection on output and input 4kV according IEC644 & 5 Large range : 3,53VDC with an input current < ma on all the range. Green LED visualization on the input. IP housing Low zero cross voltage ( <5V) Mounting and dismounting on DIN rail without any tool or directly mountable on panel. Designed in conformity with EN (IEC94743) and EN695 ULcUL Dimensions : (*) : was Red on the first pieces. page /5 GB SILD8657 Output : 55VAC 3A(*) Input : 3,53VDC I<mA Diagnostic : 3VDC ma PATENTED! Mains 4VAC 5hz 8A (*) see conditions (thermal curve page 4) Output status diag SSR Typical application: 9kW resistor (AC5 load) on 4 VAC Input Control CHARGE/LOAD Proud to serve you All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis.

2 Control characteristics (at 5 C) DC Input : Ic = f( Uc) Paramètre / Parameter Symbol Min Nom Max Unit Control voltage Uc 3, V Control current (@ Uc ) Ic < < < ma 8 Release voltage Uc off V 6 Input LED green Reverse voltage Urv 3 V 4 Clamping voltage Uclamp 4 V Input immunity : EN644 kv Input immunity : EN645 KV Output characteristics (at 5 C) Parameter Conditions Symbol Typ. Unit Load voltage Ue 4 V rms Operating range Ueminmax 55 V rms Peak voltage Up V Clamping voltage Uclamp 8 (@ma) V Zero cross level Usync 4 V Latching voltage Ie nom Ua 4 V AC5 nominal current : permanent ( see Fig. page 4 ) Ie AC5 3 A rms AC53 nominal current Ie AC53 A rms Non repetitive overload current tp=ms (Fig. 3) Itsm 55 A On state voltage drop (typical 5 C Vt,9 V Dynamic resistance (typical value) rt 8 mω Output Power dissipation (typical value) Pd,8xIe,8xIe W Thermal resistance between junction to air Rthj/a 3,3 (,5) K/W Off state leakage 5Hz Ilk <5 ma Minimum load current Iemin ma Turn on time Uc nom DC,f=5Hz ton max ms Turn off time Uc nom DC,f=5Hz toff max ms Operating frequency range f 444 Hz Off state dv/dt dv/dt 5 V/µs Maximum di/dt non repetitive di/dt 5 A/µs It (<ms) I t 5 A s Conducted immunity level IEC 44 (burst) 4kV criterion A Conducted immunity level IEC 45(schocks) 4kV criterion A Short circuit protection FERRAZ grc 5A/3A/5A/63A 4x5 Fax 33 () Service Commercial France Tél. : 33 () Sales Dept.For Europe Tel. : 33 () Sales Dept. Asia : Tél. 33 () Ic ( ma) Uc ( VDC) page /5 GB General characteristics (at 5 C) Input to output insulation Ui 4 VRMS Output to status insulation Ui 5 VRMS Output to case insulation Ui 4 VRMS Insulation resistance Ri (@5VDC) MΩ Rated impulse voltage Uimp 4 V Protection level / CEI59 IP Pollution degree Vibration resistance 55 Hz according to CEI68 : double amplitude,5 mm Shocks resistance according to CEI68 ( on DIN rail / with screws) 3/5 g Ambient temperature (with no icing or condensation) 4 /8 C Storage temperature (with no icing or condensation) 4/ C Ambient humidity HR 4 to 85 % Weight 6 g Conformity EN (IEC94743) Conformity UL/cUL pending

3 page 3 /5 GB Status output answer characteristics (at 5 C) Paramètre / Parameter Conditions Symbol Min Nom Max Unit Voltage range Us 4 3 V Output current Id,, A On resistance Rdson Ω Open delay (faults) fig. Uenom 7 ms Total open delay (faults) fig. Uenom, Uc=V ms Closed mains delay Uenom, Uc=Ucnom tc ms Closed mains delay Uenom, Uc=Ucnom tc ms Maximum cable length for open load ( maximum load due to capacitor) 4 m Diagnostic description Control Control LED Mains Load SSR Status LED Output status No x x Open No x x Open Yes OK OK closed Yes OK OK closed Yes Open OK Open Yes OK shortcircuit Open Yes Open OK Open Yes OK shortcircuit Open Notices The red LED luminosity depends on : Ue voltage. Control : ON,OFF Load type. The status outputs can be connected in serial for only one information. NPN/ PNP output is possible with status ( insulation with the ) and no power supply for the relay. In case of using with a mains voltage lower than specifications, the SSR works correctly, but an alarm status can be given with OFF. In this case, the status works only with ON with the diagnostic of open load or SSR shortcircuit. ON OFF Ouvert/ Open Fermé/ Closed Reaseau / Mains Commande / Control Courant / Current Sortie d'état / Status output ABSENCE RESEAU / OPEN MAINS ton tc Synoptic : CHARGE COUPEE / OPEN LOAD tc toff THYRISTORS EN COURT CIRCUIT / SHORTCIRCUIT SCR tc * Status (static output) is normally closed without failure on the relay and the load, and the yellow LED is switched ON : That means there is voltage across the SSR without. current inside the SSR with. * In case of failure on the load ( opened) or on the SSR (shortcircuited) : the status is opened. the yellow LED is switched OFF. Led de commande / Control LED Led d'état / Status LED Mains 55V Important : In case of long wiring cable between the SSR and the load ( > 5 meters), it is possible than the diagnostic system can't detect an open load. Control Ic Uc Id A A green L Fuse Status Vds red Load T Fax 33 () Service Commercial France Tél. : 33 () Sales Dept.For Europe Tel. : 33 () Sales Dept. Asia : Tél. 33 ()

4 page 4 /5 GB Thermal specifications. The curve "" gives the limits of the product. The temperature reached are acceptable for the components. These values are in compliance with most of SSRs manufacturers. In a cabinet with a minimum of ventilation or a non permanent current, these values are correct. The curve "" gives the limits of the product according to EN with a maximum rise temperature of 5 C (@4 C) for a permanent working and in air calm ( test during 8 hours). For a non permanent current, you can calcule the average power = Pd x duty cycle and check the rise temperature : Tj = Pd x Rthj/a (Pd and Rthj/a are given page )). The junction temperature must not exceed 5 C at the maximum ambient temperature. The maximum current is limited to the size of the thyristors = 5A. The thermal constant (Cth) of the product is 7 minutes. That means the rise temperature is only 63% of the stabilized temperature after a running time of 7 minutes. I(A) Tambient( C) fig Overload current. No repetitive Itsm is given without voltage reapplied. This curve is used for the determination of the protection. Repetitive Itsm is given for inrush current with initial Tj = 7 C. In normal working, this curve musn t be exceed. Be carefull, the repetition of the surge current decrease the lifetime SSR s. fig 3 Itsm (Apeak) Fig.3 Surge current : Itsm (Apeak) = f(t) for 5A models with Itsm =55A 6 4, Repetive surge current with voltage reapplied., No repetive surge current without voltage reapplied. t (s) Mounting and dismounting on DIN rail without any tool. Panel Mounting M5 M4 Mounting Dismounting DIN rail connected to protection wire (ground). Drill for vertical can be adjusted,7mm 88±mm Warning! semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction with an adapted circuit breaker with isolation feature or a similar device in order to ensure a reliable isolation in the event of wrong function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration...). Fax 33 () Service Commercial France Tél. : 33 () Sales Dept.For Europe Tel. : 33 () Sales Dept. Asia : Tél. 33 ()

5 Connections. celpac For the output terminals, the wire cross sections must be adapted to the load current and to the overcurrent protection device characteristics. The relay rated voltage must be adapted to the mains rated voltage. celpac use screw clamp connections. Mounting Only in vertical position: The user should protect heat sensitive materials as well as persons against any contacts with the heatsink. For non vertical mounting, the load current must be 5% lower than the rated one. For a good cooling, the SSR needs an air convection. Less convection air produces an abnormal heating. Keep a distance between the upper SSR and the lower SSR. In case of no space between two SSR (zero space between two SSRs), please reduce the load current. For further details refer to below : Derating current with no space between SSRs AC5 nominal currents are given with a space of,5mm between each SSR, for a permanent current during a minimum time of 8 hours in air calm according to IEC In case of non permanent currents or in case of SSRs are mounted with no space, you must check the heatsink temperature never exceed 9 C. When the SSRs are mounted side to side ( no space between each relay) a derating current of 5% must be take into account. A forced cooling ( fan inside the cabinet) improves significantly the thermal performances. Typical application : LOADS SILD product is designed mainly for AC5 résistive load. AC53 motor current are also given. For other loads, check the inrush current at turn ON and possible overvoltages at turn OFF or consult us : * AC55b : Incandescent lamps : Inrush current is generally times In during few ms. So limit the nominal current at about 5A. * AC55a : Electric discharge lamp : These loads often have overcurrent at turn ON and overvoltage at turn OFF, so we advise to use 4VAC SSR on 3VAC mains. * AC56a : Transformers loads : Very high inrush current up to times In. We advise to use random SSR. * AC56b : Capacitors loads : Very high current at turn ON and overvolatge at turn OFF, please consult us with 6V peak SSR with high inrush current. L wires (mm ) x(,75>,5) L = 6mm Power x(,5>6) x(,5>) L = mm L torques,4n.m (,6N.m max),n.m (,8N.m max) vertical position diagnostic outputs in serie page 5 /5 GB screwdriver screwdriver 3,5x,5mm Pozidriv/,8x5,5 (x6) Fuse Fusible 8mm Protection : To protect the SSR against a shortcircuit of the load, use a fuse with a I t value = / I t value specified page. A test has been made with FERRAZ fuse ( see page ). It is possible to protect SSR by MCB ( miniature circuit breaker). In this case, see application note ( SSR protection) and use a SSR with high I t value (5A s minimum). L Diag L Diag EMC : Immunity : We give in our datasheets, the immunity level of our SSRs according to the main standards for this type of products : EN644 &5. You can see the high immunity level in comparison with the products on the market. Emission: SSRs are complex devices which must be interconnected with other equipment (loads, cables,etc.) to form a system. Because the other equipment or the interconnections may not be under the of celduc, it shall be the responsibility of the system integrator to ensure that systems containing SSRs comply with the requirements of any rules and regulations applicable at the system level.. Consult celduc laboratory which can make some tests in your application. T A A Load Charge T A A Fax 33 () Service Commercial France Tél. : 33 () Sales Dept.For Europe Tel. : 33 () Sales Dept. Asia : Tél. 33 () N N