Model 3244MV. MultiVariable Temperature Transmitter with Profibus PA. Product Data Sheet

Transcription

1 Product Data Sheet Model 3244MV MultiVariable Temperature Transmitter with Profibus PA PROFIBUS PA CAPABILITIES CanbeintegratedtoaProfibusDPnetwork Reduces wiring costs and installation commissioning, operation, and maintenance time compared to traditional smart transmitters MULTIVARIABLE BENEFITS Reduce process variability with differential temperature measurement Pre-configure your transmitter at the Rosemount factory with custom configuration options SUPERIOR PERFORMANCE AND RELIABILITY Accuracy: ±0.10 C (± 0.18 F) for Pt 100 RTDs 5 year stability 18 bit analog-to-digital converter with ambient temperature compensation provides outstanding measurement performance Dual-compartment housing provides superior reliability in high-humidity, corrosive, and RFI environments COMPLETE POINT SOLUTIONS Have your temperature assembly shipped installation-ready. This complete temperature assembly includes the transmitter, sensor, extension, and thermowell. This assembly is shipped fully assembled, calibrated, wired and configured. VISITROSEMOUNT PRODUCTSONTHE WORLD WIDEWEBAT

2 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA Rosemount Complete Point Solutions The Rosemount Complete Point Solutions program provides fully engineered measurement solutions, combining the best product and practices for improved performance, reliability, and cost of ownership. Rosemount Inc. will supply the complete temperature measurement assembly, including the transmitter, sensor, extension, and thermowell. When you purchase the complete measurement assembly from Rosemount Inc., you need only remove it from the box, tap into the process, and make electrical connections. To order Rosemount temperature sensors and accessories, refer to the appropriate volume of the Rosemount Temperature Sensors and Accessories Product Data Sheet. Items i n Volume 1 (document number ) can be ordered through the Rosemount sales offices in North America and Latin America. Items in Volume 2 (document number ) can be ordered through Rosemount sales offices in Europe and Asia-Pacific. TRANSMITTER DESCRIPTION Inputs The transmitter is compatible with any of the temperature sensor listed below: 2-, 3-, and 4-wire RTD Sensors Pt 100 Pt 200 Pt 500 Pt 1000 ( = ) Pt 100 ( = ) Ni 120 Cu 10 Thermocouples (1) Type B Type E Type J Type K Type N Type R Type S Type T Custom Input Sensors Special RTD or thermocouple calibration schedules NIST Type C thermocouple Refer to Table 1 on page 7 for a complete listing of input options and specifications. The sensor type and configuration are software-selectable using any Profibus PA Class 2-compliant host. In addition, you can select appropriate display scaling for convenient readout directly in engineering units including Celsius, Fahrenheit, Kelvin, Rankine scale, millivolts, and ohms. A complete line of temperature sensors, thermowells, and accessory mounting hardware are available from Rosemount Inc. Refer to the Temperature Sensors and Accessories for Temperature Transmitter Assemblies Product Data Sheets, Volumes 1, 2, or 3. Figure 1 illustrates how a temperature signal is channelled through the transmitter. Millivolt Input Sensors 10 to 100 millivolts 2-, 3-, and 4-wire Ohm Input Sensors 0 to 2000 ohms (1) To prevent ground loops and potential measurement errors, avoid using two independently-grounded thermocouples 2

3 Rosemount Inc. Function Blocks AI1,AI2,AI3 User-Selectable Input RTD Thermocouple Millivolt Ohm Sensor 1 Sensor 2 (optional) PROFIBUS PA Communication Stack Physical Block Physical device information Analog-to-Digital Signal Conversion Cold Junction Compensation Transducer Block Sensor 1 temperature Sensor 2 temperature Differential temperature Terminal temperature Diagnostics Engineering units Input-to-Output Galvanic Isolation _01B FIGURE 1. Block Diagram for the Model 3244MV MultiVariable Temperature Transmitter with Profibus PA. Output The output signal is linearized with temperature ( C, F, R, or K), or linear with input (ohm or mv). Thermocouple inputs are automatically compensated for cold junction variations. The Model 3244MV has the unique ability to output multiple digital signals. The transmitter comes with three analog input (AI) function blocks. Any three of the following outputs, which reside in the transducer block, can be assigned to the AI function blocks: Sensor 1 Sensor 2 Differential temperature Terminal temperature Electronics Module The electronics module uses digital application-specific integrated circuit (ASIC), microcomputer, and surface-mount technology. The electronics digitize the input signal from the sensor and apply correction coefficients selected from nonvolatile memory. LCD Meter The optional LCD meter easily plugs into the electronics module and displays the digital output in engineering units. Data Storage The transmitter stores configuration data in the nonvolatile FLASH memory of the electronics module. The data are retained in the transmitter when power is interrupted, allowing the transmitter to function immediately upon power-up. The configuration data is useful for equipment traceability, a requirement of ISO RTD EMF Correction RTD sensing elements often produce a small voltage that can initiate sensor errors. The voltage can be generated either by a battery effect (from electrolytes present in the sensor) or by a thermocouple effect at the sensing element junctions. EMF errors of this sort are present in RTDs even when no current is being passed through the sensor. The Model 3244MV transmitter, however, is capable of detecting and eliminating these errors, providing more precise measurement. 3

4 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA SOFTWARE CAPABILITIES The software used in the transmitter allows for remote testing and configuration using any Profibus PA Class 2-compliant host. Transducer Blocks Transducer blocks (TB) allow several inputs to be read by the host. TB1 contains sensor 1 data, TB2 contains sensor 2 data, and TB3 contains sensor differential data. All TBs contain the terminal temperature. Multiple transducer blocks give any Profibus PA Class 2-compliant host the ability to configure basic device features. The Siemens Profibus PA Class 2-compliant host, through the use of device description files, allows for additional configuration parameters, including: Special sensor types Calibration Diagnostics LCD meter configuration. Physical Block The physical block contains transmitter information including: Available memory Manufacturer identification Device type Software tag Any additional identification. Analog Input Function Block The analog input function block processes the measurement and makes it available to other function blocks. Using this block, the following can be changed: Filtering Alarming Engineering unit Basic Configuration Basic configuration of the of the Model 3244MV requires connecting the transmitter to a power supply, connecting the sensor, and defining operational parameters. The transmitter is easily configurable using any Profibus PA Class 2 compliant host. The following are some examples of user-configurable parameters: Sensor type Number of sensor input wires Damping Engineering unit selection Tagging information can be entered into the transmitter to allow identification and a physical description. 30-character tags are provided for identification of the transmitter and each function block. Advanced Configuration Using the Siemens Profibus PA Class 2-compliant host, the transmitter can be configured for advanced features such as: Transmitter-Sensor Matching LCD meter configuration 50 or 60 Hz line filtering option Increased Sensor Accuracy (Transmitter-Sensor Matching) A specifically matched temperature sensor and transmitter significantly improves measurement accuracy. The Model 3244MV is designed to accept Callendar-Van Dusen constants from a calibrated RTD schedule and generate a custom curve to match any specific sensor curve. These constants can be programmed at the factory by using option code C2 when ordering or they can be entered or changed s in the field using the Siemens Profibus PA Class 2-compliant host. Typical Example: System Accuracy Comparison at 150 C Span of 0 to 200 C Standard Series 68 Sensor Model 3244MV ± 0.10 C Standard 68 RTD Total System (1) ±1.05 C ±1.05 C Matched Series 68 Sensor Model 3244MV ± 0.10 C Matched 68 RTD ±0.18 C Total System (1) ±0.28 C (1) Calculated using RSS statistical method: Total System = Transmitter Accuracy 2 + Transmitter Accuracy 2 Accuracy 4

5 Rosemount Inc. Specifications and Reference Data FUNCTIONAL SPECIFICATIONS Inputs See Table 1. User-selectable. (sensor terminals are rated to 42.4 V dc.) Outputs Manchester-encoded digital signal that conforms to IEC and ISA Isolation Input/output isolation tested to 500 V rms (707 V dc). Power Supply External power supply required. Transmitter operates between 9.0 and 32.0 V dc, 17.5 ma maximum. (Transmitter power terminals are rated to 42.4 V dc.) FIGURE 3. LCD - Measurement with UNCERTAIN Status. If the measurement status goes to BAD, the LCD toggles between the screens illustrated in Figure 4, which shows the BAD status and substatus diagnostic _03F, 03F Local Display he optional five-digit LCD meter includes display options for engineering units ( F, C, R, K, ohms, and millivolts) and milliamps. The display can alternate between selected measurements, including sensor 1, sensor 2, differential, and terminal temperatures. Digits are 0.4 inches (8 mm) high. Display settings are pre-configured at the factory according to the transmitter configuration. Display settings can be reconfigured in the field using the Siemens Profibus PA Class 2-compliant host. Figure 2 illustrates the temperature display when status is GOOD, while Figure 3 illustrates the temperature display when status is UNCERTAIN. FIGURE 4. LCD BAD Status and Substatus Diagnostic. Temperature Limits Ambient Limit Without LCD Meter 40 to 185 F ( 40 to 85 C) With LCD Meter 4 to 185 F ( 20 to 85 C) Storage Limit 60 to 250 F ( 50 to 120 C) 50 to 185 F ( 45 to 85 C) Status If self-diagnostics detect a sensor burnout or a transmitter failure, the status of the measurement will be updated accordingly _03G, 03H FIGURE 2. LCD Measurement with GOOD Status _03E Humidity Limits 0 100% relative humidity. Turn-on Time Performance within specifications is achieved less than 30.0 seconds after power is applied to the transmitter. 5

6 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA Update Time Approximately 0.5 seconds for a single sensor (1.0 second for two sensors). Profibus PA Specifications Class 1 Communications AI1.OUT AI2.OUT AI3.OUT Update rate 1.0 second Hazardous Locations Certifications NOTE: Information in this section may not be currently available. Please consult the factory for details. Factory Mutual (FM) Approvals E5 Explosion Proof for Class I, Division 1, Groups A, B, C, and D. Dust-Ignition Proof for Class II, Division 1, Groups E, F, and G. Dust-Ignition Proof for Class III, Division 1 hazardous locations. Non-Incendive for Class I, Division 2, Groups A, B, C, and D (T4). Indoor and outdoor use. Ambient Temperature Limit: 50 to 85 C. Explosion Proof approval only when connected in accordance with Rosemount drawing For Group A, seal all conduits within 18 inches of enclosure; otherwise, conduit seal not required for compliance with NEC 501-5a(1). I5 Intrinsically Safe for Class I, II, and III, Division 1, Groups A, B, C, D, E, F, and G. Non-Incendive Field Circuit for Class I, II, III; Division 2, Groups A, B, C, D, F, and G. Ambient Temperature Limit: 60 to 60 C. Intrinsically safe and Non-Incendive field circuit approval only when installed in accordance with Rosemount drawing K5 Combination of E5 and I5 Canadian Standards Association (CSA) Approvals E6 Explosion Proof for Class I, Division 1, Groups A, B, C, and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 hazardous locations. Suitable for Class I, Division 2, Groups A, B, C, and D. Conduit seal not required. Ambient Temperature Limit: 50 to 85 C. I6 Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 hazardous locations when installed in accordance with Rosemount drawing Ambient Temperature Limit: 60 to 60 C C6 Combination of E6 and I6 FM and CSA Combinations of Approvals KB Combination of K5 and C6 Institut Scientifique de Service Public (ISSeP)/CENELEC Flameproof Approval E9 EEx d IIC T6 (T amb = 20 to 60 C). Cert No. 95D British Approvals Service for Electrical Equipment in Flammable Atmospheres (BASEEFA)/CENELEC Approvals N1 I1 CENELEC Type n EEx nl IIC T5 (T amb = 40 to 70 C) Cert No. BAS98ATEX 3358 X Special Conditions for Safe Use (x): A transmitter fitted with the transient protection terminal block is not capable of withstanding the electrical strength test required by Clause 9.1 of EN 50021: This condition must be taken into account during installation. CENELEC Intrinsic Safety, EEx ia IIC T4 (T amb = 60 to 60 C) Cert. No. BAS98ATEX 1357 X Input Entity Parameters: Power/Communications U max:in = 30 V dc I max:in = 300 ma P max:in = 1.3 W C eq = µf L eq = 20 µh Special Conditions for Safe Use (x): A transmitter fitted with the transient protection terminal block is not capable of withstanding the insulation test required by EN 50020, Clause 5.7 (1977). This condition must be taken into account during installation. NOTE Additional Approvals Pending. 6

7 Rosemount Inc. PERFORMANCE SPECIFICATIONS The transmitter maintains a specification conformance of at least 3 (See page 13). Accuracy Refer to Table 1. Sensor Options TABLE 1. Input Options/Accuracy. Sensor Reference Accuracy Over Input Ranges Range(s) C F C F 2-, 3-, 4-Wire RTDs Pt 100 ( = ) IEC 751; = , to to 1562 ± 0.10 ± 0.18 Pt 100 ( = ) JIS 1604, to to 1193 ± 0.10 ± 0.18 Pt 200 IEC 751; = , to to 1562 ± 0.22 ± 0.40 Pt 500 IEC 751; = , to to 1562 ± 0.14 ± 0.25 Pt 1000 IEC 751; = , to to 572 ± 0.08 ± 0.14 Ni 120 Edison Curve No to to 572 ± 0.08 ± 0.14 Cu 10 Edison Copper Winding No to to 482 ± 1.00 ± 1.80 Thermocouples Cold Junction Adds C to Listed Accuracy NIST Type B (Accuracy varies according to input range) NIST Monograph to to to to 3308 ±3.0 ±0.75 ±5.4 ±1.35 NIST Type E NIST Monograph to to 1832 ± 0.20 ± 0.36 NIST Type J NIST Monograph to to 1400 ± 0.25 ± 0.45 NIST Type K NIST Monograph to to 2502 ± 0.50 ± 0.90 NIST Type N NIST Monograph to to 2372 ± 0.40 ± 0.72 NIST Type R NIST Monograph to to 3214 ± 0.60 ± 1.08 NIST Type S NIST Monograph to to 3214 ± 0.50 ± 0.90 NIST Type T NIST Monograph to to 752 ± 0.25 ± 0.45 Millivolt Input Not approved for use with CSA option code I6 10 to 100 mv ± mv 2-, 3-, 4-Wire Ohm Input 0 to 2000 ohms ±0.35 ohm Accuracy Notes Differential capability exists between any two sensor types. For all differential configurations, the input range is X to +Y where X = Sensor 1 minimum Sensor 2 maximum Y = Sensor 1 maximum Sensor 2 minimum Using thermocouples in monitoring and differential temperature applications: Two independently-grounded thermocouples could create ground loops and could result in measurement errors. Avoid using two independently grounded thermocouples. Accuracy for differential configurations: If sensor types are similar (for example, both RTDs or both thermocouples), the accuracy will equal 1.5 times worst case accuracy of either sensor type. If sensor types are dissimilar (for example, one RTD and one thermocouple), the accuracy will equal Sensor 1 Accuracy + Sensor 2 Accuracy. 7

8 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA Stability ±0.1% of reading or 0.1 C (0.18 F), whichever is greater; 2 years for RTDs. ±0.1% of reading or 0.1 C (0.18 F), whichever is greater; 1 year for thermocouples. Five-Year Stability ± 0.15% of reading or 0.15 C (0.27 F), whichever is greater; 5 years for RTDs ±0.5% of reading or 0.5 C (0.9 F), whichever is greater; 5 years for thermocouples. RFI Effect Worst case RFI Effect is equivalent to the transmitter nominal accuracy specification, according to Table 1, when tested in accordance with EN , 10 V/m, 80 to 1000 MHz, and 30 V/m, MHz (Increased NAMUR), with twisted shielded cables. Vibration Effect Transmitters tested to the following specifications with no effect on performance: Frequency Acceleration Hz 0.21 mm peak displacement Hz 3 g Self Calibration When reading the temperature measurement, the analog-to-digital circuitry automatically self-calibrates for each temperature update by comparing the dynamic measurement to extremely stable and accurate internal reference elements. Ambient Temperature Effect Transmitters may be installed in locations where the ambient temperature is between 40 and 85 C ( 40 and 185 F). Each transmitter is individually characterized over this ambient temperature range in order to maintain excellent accuracy performance in dynamic industrial environments. This special manufacturing technique is achieved through extreme hot and cold temperature profiling with individual adjustment factors programmed into each transmitter. Transmitters automatically adjust for component drift caused by changing environmental conditions. Refer to Tables 2, 3, and 4. (1) TABLE 2. Ambient Temperature Effects on RTDs Sensor Type Pt 100 ( = ), Pt 100 ( = ), Pt 500 Pt 200 Ni 120, Pt 1000 Cu 10 Temperature Effects Example (see Tables 2, 3, and 4) When using a Pt 100 ( = ) sensor input with a 30 C ambient temperature, temperature effects would be C (30 20) = C. Worst case error would be Sensor Accuracy + Temperature Effects = 0.10 C = C Total Probable Error = Accuracy per 1.0 C (1.8 F) Change in Ambient Temperature (1) C ( F) C ( F) C ( F) C (0.027 F) TABLE 3. Ambient Temperature Effects on Thermocouples (R = the value of the reading) NIST Type Accuracy per 1.0 C (1.8 F) Change in Ambient Temperature (1) Temperature Range ( C) B R C (0.0021% of (R 300)) 300 R < C ( % of (R 100)) 100 R < 300 E C + ( % of R) All J C + ( % of R) R C + ( % of R ) R < 0 K C + ( % of R) R C + ( % of R ) R < 0 N C + ( % of R) All R, S C R C ( % of R) R < 200 T C R C + (0.0036% of R ) R < 0 TABLE 4. Ambient Temperature Effects on Millivolt or Ohm Input Accuracy per 1.0 C (1.8 F) Input Type Change in Ambient Temperature (1) Millivolt mv 2-, 3-, and 4-wire Ohm Ω = C _03E (1) Change in ambient is in reference to the calibration temperature of the transmitter (20 C (68 F) typical from factory). 8

9 Rosemount Inc. PHYSICAL SPECIFICATIONS Conduit Connections 1 /2 14 NPT, PG13.5 (PG11), M (CM20) or JIS G 1 /2 conduit. Materials of Construction Electronics Housing Low-copper aluminum or CF-8M (cast version of 316 Stainless Steel). Paint Polyurethane. Cover O-rings Buna-N. Mounting Transmitters may be attached directly to the sensor. Optional mounting brackets permit remote mounting (see page 11). Weight Aluminum: 3.2 lb (1.4 kg). Stainless Steel: 7.9 lb (3.6 kg). Add 0.3 lb (0.1 kg) for LCD meter options. Add 0.7 lb (0.3 kg) for B4 bracket options. Add 1.5 lb (0.7 kg) for B5 bracket options. Enclosure Ratings NEMA 4X and CSA Enclosure Type 4X, IP66, and IP68. Rosemount Conformance to Specifications You can be confident that a Rosemount product not only meets its published specifications, but most likely exceeds them. Our advanced manufacturing techniques and use of Statistical Process Control provide specification conformance to at least ± 3 (1).In addition, our commitment to continual improvement ensures that product design, reliability, and performance improve every year. For example, the Reference Accuracy distribution for the Model 3244MV MultiVariable Temperature Transmitter is shown to the right. (2) Our Specification Limits are ± 0.10 C, but, as the shaded area shows, approximately 68% of the units perform three times better than the limits. Therefore, it is very likely that you will receive a device that performs much better than our published specifications. Conversely, a vendor who grades product without using Process Control, or who is not committed to ± 3 performance, will ship a much higher percentage of units that are barely within (or even outside of) advertised specification limits. Lower Specification Limit 3 Typical Accuracy Upper Specification Limit GRAPH (1) Sigma ( ) is the Standard Deviation of a statistical distribution, and describes the dispersion (spread) of the distribution. (2) Accuracy distribution shown is for Model 3244MV, Pt 100 RTD sensor, Range 0 to 100 C. 9

10 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA REFERENCE DATA Transmitter Exploded View Standard Cover with Wiring Diagram Nameplate (includes serial number and model number) Approvals Label Profibus PA Electronics Module Assembly LCD Meter (Optional) Housing Assembly with Permanent Terminal Block LCD Meter Cover (Optional) A03A FIGURE 5. Transmitter Exploded View. Top View Side View Standard Cover 1 /2 14 NPT (1) Conduit Entry Meter Cover 5.2 (132) 4.4 (112) With LCD Meter 2.0 (51) 4.4 (112) Nameplate 3 /8 16 UN 2B 4.4 (112) 1 /2-14 NPT (1) Conduit Entry B02A, 0000A07A Note: Dimensions are in inches (millimeters) Note: Dimensions are in inches (millimeters) 1) M20 x 1.5 (CM20), PG 13.5 (PG 11), and JIS G 1 /2 threads made with adapter that extends approximately one inch from housing. FIGURE 6. Transmitter Dimensional Drawings 10

11 Rosemount Inc. Option Code B4 Bracket Panel Mount Pipe Mount (2) 5 /16-inch Bolts not provided 3.65 ±0.06 (92.7) 2.81 ±0.03 (71.4) 1.55 (39.4) 2.0 ± 0.03 (50.8) 1.04 (26) 1.0 (25.4) 0.41 (10.4) Diameter (9.5) Diameter 2-inch (50.8) Pipestand A01A, A14A, 0000A01A, 0427B, 0427C Note: Dimensions are in inches (millimeters) Note: Dimensions are in inches (millimeters) FIGURE 7. Optional Transmitter B4 Mounting Bracket. Option Code B5 Bracket 2 (51) Diameter Washer (Provided) 6.6 (162.6) 1.0 (25) 7.15 ( ) A01B ÿþýüûúùø üöõøþöõúôóüúøöúøöòñüõúð øïïø üýüóõî FIGURE 8. Optional Transmitter B5 Mounting Brackets 11

12 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA ORDERING INFORMATION Model Product Description 3244MVW Temperature Transmitter with Dual Sensor Input and Profibus PA Digital Signal Code Housing Conduit Thread 1 Aluminum ½ 14 NPT 2 Aluminum M (CM20) 3 Aluminum PG 13.5 (PG 11) 4 Aluminum JIS G ½ 5 SST ½ 14 NPT 6 SST M (CM20) 7 SST PG 13.5 (PG 11) 8 SST JIS G ½ Code Hazardous Locations Certifications E5 FM Explosion-Proof and Non-Incendive Approval I5 FM Intrinsic Safety and Non-Incendive Field Circuit Approval K5 FM Intrinsic Safety, Explosion-Proof, and Non-Incendive Approval Combination E6 CSA Explosion-Proof and Non-Incendive Approval I6 CSA Intrinsic Safety and Non-Incendive Field Circuit Approval C6 CSA Intrinsic Safety, Explosion-Proof, and Non-Incendive Approval Combination KB FM and CSA Intrinsic Safety, Explosion-Proof, and Non-Incendive Approval Combination E9 ISSeP/CENELEC Flameproof Approval N1 BASEEFA/CENELEC Type n Approval I1 BASEEFA/CENELEC Intrinsic Safety Approval NA No Approval Required Note: Additional approvals pending Please Contact Rosemount Customer Central for more information. Code Options Accessory Options B4 Universal Mounting Bracket for 2-inch Pipe Mounting and Panel Mounting SST Bracket and Bolts B5 Universal L Mounting Bracket for 2-inch Pipe Mounting SST Bracket and Bolts M5 LCD Meter G1 External Ground Lug Assembly Custom Configuration Options U4 Two Independent Sensors U5 Differential Temperature C1 Factory Configuration of Date, Descriptor, and Message Fields C2 Trim to Specific Rosemount RTD Calibration Schedule (Transmitter-Sensor Matching) C4 5-Point Calibration (use option code Q4 to generate a Calibration Certificate) F5 50 Hz Line Voltage Filter Assembly Options X1 Assemble Transmitter to a Sensor Assembly (hand tight, Teflon (PTFE) tape where appropriate, fully wired) X2 Assemble Transmitter to a Sensor Assembly (hand tight, no Teflon (PTFE) tape, unwired) X3 Assemble Transmitter to a Sensor Assembly (wrench tight, Teflon (PTFE) tape where appropriate, fully wired) Note: Option codes X1 and X3 are not available with CSA approvals. Calibration Certification Options Q4 Calibration Certificate (3-Point standard; use C4 with Q4 option for a 5-Point Calibration Certificate) Typical Model Number: 3244MVW 1 NA B4 M5 X1 12

13 Rosemount Inc. Tagging Hardware Tag no charge tagged in accordance with customer requirements stainless steel construction permanently attached to transmitter character height is 1 /16-in. (1.6 mm) Software Tag no charge transmitter can store up to 30 characters. If no such characters are specified, the first 30 characters of the hardware tag are used as the default. TRANSMITTER CONFIGURATION The transmitter is available from the factory with either the standard configuration or one of the custom configuration options when specified in the model number. Use Configuration Data Sheet on page 15 if any modifications are needed to the selected configuration. The configuration settings and block configuration may be changed in the field using a Profibus PA Class 2-compliant host. Custom Configuration If you want to have the Model 3244MV factory configured for one of the applications described under Monitoring Applications Option Code U4 (Two Independent Sensors) indicate the appropriate option code in the model number when ordering. If you do not order one of these option codes, the transmitter will be shipped with its standard configuration. Standard Configuration Unless otherwise specified, the transmitter will be shipped as follows: Standard Block Configuration TB1 T 1 T 1 T b Monitoring Applications Option Code U4 (Two Independent Sensors) This configuration optimizes the transmitter for use in applications involving basic process monitoring. Two single-element sensors are used with this option. When this option is ordered, the transmitter will be shipped with the standard configuration settings with the following changes/additions: Option Code U4 Custom Configuration Settings Sensor Type Sensor 1 3-wire Pt 100 = RTD Sensor 2 3-wire Pt 100 = RTD Function Block Tags: Analog Input Blocks AI1, AI2, AI3 Transducer Block TB1, TB2, TB3 Physical Block RB Option Code U4 Custom Block Configuration TB1 TB2 T 1 T b T 2 T b AI 1 T 1 = Sensor 1 Temperature T b = Terminal Temperature AI 1 AI 2 T 1 = Sensor 1 Temperature T b = Terminal Temperature T 2 = Sensor 2 Temperature Standard Configuration Settings Sensor Type 4-wire Pt 100 = RTD Damping 2.0 seconds Units of Measurement Degrees Celsius ( C) Line Voltage Filter (1) 60 Hz Software Tag See Tagging Function Block Tags: Analog Input Blocks AI1, AI2, AI3 Transducer Block TB1, TB2, TB3 Physical Block RB Local Display (1) (when installed) Engineering Units (1) These configuration setting can only be changed using the Siemens Profibus PA Class 2 host. 13

14 Model 3244MV MultiVariable Temperature Transmitter with Profibus PA Option Code U5 (Differential Temperature) This configuration is used to measure the differential between two process temperatures. When this option is ordered, the transmitter will be shipped with the standard configuration settings with the following changes/additions: Option Code U5 Custom Configuration Settings Sensor Type Sensor 1 3-wire Pt 100 = RTD Sensor 2 3-wire Pt 100 = RTD Function Block Tags: Analog Input Blocks AI1, AI2, AI3 Transducer Block TB1, TB2, TB3 Physical Block RB Option Code U5 Custom Block Configuration TB1 TB2 TB3 T 1 T b T 2 T b T T b AI 2 AI 3 AI 1 T 1 = Sensor 1 Temperature T 2 = Sensor 2 Temperature T b = Terminal Temperature T = Differential Temperature Option Code C1 Customer specifies the following data in addition to the standard configuration parameters: Date: day, month, year Descriptor: 16 alphanumeric characters Message: 32 alphanumeric characters Completion of Configuration Data Sheet is required. Option Code C2 (Transmitter-Sensor Matching) A customer must specify and order a Rosemount Series 65, 68, or 78 RTD sensor with a special calibration schedule. Option Code C4 (Five-Point Calibration) Transmitter is calibrated and verified at 0, 25, 50, 75, and 100% digital output points. Use with Rosemount Calibration Certificate Q4 to generate a 5-point calibration certificate. External Ground Lug Assembly The external ground lug assembly can be ordered by specifying option code G1 in the transmitter model number (see Ordering Information on page 12) when an enclosure is also specified. However, some approvals automatically include the ground lug assembly in the transmitter shipment. In these cases it is not necessary to order option code G1. See below to determine which approval options include the external ground lug assembly. Approval Type Ground Lug Included? E5 No Order option code G1 for ground lug I5 No Order option code G1 for ground lug K5 No Order option code G1 for ground lug E6 No Order option code G1 for ground lug I6 No Order option code G1 for ground lug External Ground Lug Assembly C6 KB NA E9 No Order option code G1 for ground lug No Order option code G1 for ground lug No Order option code G1 for ground lug Yes 1groundlug A02A N1 Yes 1groundlug I1 Yes 1groundlug FIGURE 9. Option Code G1 External Ground Lug Assembly Installed on the Transmitter. 14

15 Rosemount Inc. CONFIGURATION DATA SHEET CUSTOMER INFORMATION Customer P.O. No. Model No. Line Item INPUT/OUTPUT INFORMATION Sensor Type Sensor 1 No of Leads. Sensor 2 No of Leads. Pt 100 = Wire Pt 100 a = Wire Pt 200 = Wire Pt 200 = Wire Pt 500 = Wire Pt 500 = Wire Pt 1000 = Pt 1000 = Pt 100 = Pt 100 = Cu 10 Cu 10 Ni 120 Ni 120 Transmitter-Sensor Matching (C2 option) Ohms NIST Type B T/C NIST Type E T/C NIST Type J T/C NIST Type K T/C NIST Type RT/C NIST Type S T/C NIST Type T T/C NIST Type N T/C mv Transmitter-Sensor Matching (C2 Option) Ohms NIST Type B T/C NIST Type E T/C NIST Type J T/C NIST Type K T/C NIST Type RT/C NIST Type S T/C NIST Type T T/C NIST Type N T/C mv Damping (for all AI function blocks) 2 Seconds Other (Value must be less than 32 seconds) Units (for all function blocks) C C F K R mv ohm 15

16 PRINTED TAGGING Hardware Tag Permanent Stainless Steel Tag Information (2 Lines 28 Character Max.) Software Tag Permanent Stainless Steel Tag Information TRANSMITTER INFORMATION (30 Character Max.) Descriptor (C1 Option) Message (C1 Option) Permanent Stainless Steel Tag Information (16 Character Max.) Permanent Stainless Steel Tag Information (16 Character Max.) Date (C1 Option) (numeric) (alphabetic) (numeric) SWITCH SELECTION Day Month Year Write Protect (Security) Off On = Standard Configuration Rosemount, the Rosemount logotype, Complete Point Solutions, and MultiVariable (MV) are registered trademarks of Rosemount Inc. Teflon is a registered trademark of E.I. du Pont de Nemours & Co. Rosemount Inc Market Boulevard Chanhassen, MN USA Tel Fax (952) Rosemount, Inc. IN U.S. A. Fisher-Rosemount Limited Heath Place Bognor Regis West Sussex PO22 9SH England Tel 44 (1243) Fax 44 (1243) Fisher-Rosemount Singapore Pte Ltd. 1 Pandan Crescent Singapore Tel (65) Fax (65) AP.RMT-Specialist@frco.com Rev. AA 04/00