FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex

Transcription

1 Data Sheet 10/-8.54 EN Level 0: Information FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation Resistance thermometer (2, 3, 4 wire circuit) Thermocouples Resistance remote signalling unit ( Ω) Voltages, mv ( mv) 2 wire technique, HART signal 1 or 2 independent channels Electrical isolation (I/O) Measured error 0.1 K Customer-specific linearization 32 tie points Continuous sensor and self-monitoring Parameter saved permanently in EEPROM Monitoring of data integrety every 10 s Wire break monitoring in acc. with NAMUR NE 89 Substitution strategy in case of error (NE 43) Approvals for explosion protection Intrinsically safe II 2 (1) G EEx [ia] ib IIC T6, mount in zone 1 II 3 G EEx n A II T6, mount in zone 2 functionality (absolute, differential, average value) EMC acc. to EN and NE Parameterization Device Management Tool: SV401 (SMART VISION) Hand held terminals: 691HT, STT04, HHT275 CoMeter (HART configurator/lc display) 5 years warranty Excellent long term stability Temperature linear output signal Enhanced self diagnostics

2 10/-8.54 EN Technical data signal (temperature linear) Residual ripple (peak-to-peak) < 0.3 % Current consumption < 3.6 ma Maximum output current.6 ma Parameterizable current error signal Underranging 3.6 ma Overranging ma Default value ma Damping t 63 = s Resistance Resistance thermometer (IEC 751, JIS, SAMA) n Pt 100/Ni 100 to Pt 1000/Ni 1000; Cu (n = 0.1, 0.2, 0.5, 1, 1.2, 2, ) Min. measuring span 15 K/50 K Resistance Ω/ Ω Min. measuring span 5 Ω/50 Ω Maximum line resistance (R w ) per core 2, 3, 4 wire 7.5 Ω, 10 Ω, 50 Ω Measuring current 300 µa Sensor short-circuit < 5 Ω (for RTD) Sensor break (temperature/resistance measurement 2, 3, 4 wire) Measuring range Ω > 530 Ω Measuring range Ω > 5.3 kω Sensor wire break monitoring in accordance with NAMUR NE 89 Sensor wire break detection 3 wire resistance measurement > 35 Ω 4 wire resistance measurement > 3.7 kω filter 50/60 Hz Thermocouples Types B, E, J, K, L, N, R, S, T, U Voltages -5 mv mv -5 mv mv Minimum measuring span 2 mv/50 mv Sensor wire break monitoring in accordance with NAMUR NE 89 Pulsed with 1 µa outside of the measuring interval Monitoring disconnectible Thermocouple measurement > 5 kω Voltage measurement > 5 kω filter 50/60 Hz Internal reference junction Pt 100, via software switchable (no jumper necessary) Standard IEC DIN IEC 751; JIS; SAMA 1) 2, 3 and 4 wire DIN ) 2, 3 and 4 wire element Measuring range Min. measuring span Sensor Thermocouple type B Thermocouple type E Thermocouple type J Thermocouple type K Thermocouple type R Thermocouple type S Thermocouple type T Thermocouple type N Thermocouple type L Thermocouple type U Resistance thermometer Pt 100 Resistance thermometer Pt 1000 Resistance thermometer Ni 100 Resistance thermometer Ni C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) C ( F) Resistance Ω Ω/ Ω 5 Ω/50 Ω Voltage mv 5 mv mv 5 mv mv 2 mv 50 mv 5 C (4 F) 30 C ( 54 F) 37 C ( 67 F) 54 C ( 98 F) 171 C (308 F) 193 C (348 F) 50 C ( 90 F) 60 C (108 F) 36 C ( 65 F) 40 C ( 72 F) 15 C ( 28 F) 50 C ( 90 F) 8 C ( 15 F) 15 C ( 28 F) 1) IEC 751 a = , JIS a = , SAMA a = ) Edison Curve No. 7 2

3 10/-8.54 EN Power supply (poling protected) Supply voltage Non-Ex-application U s = V DC For Ex-Application, max. U i = V DC 2 wire methode: power supply wires = signal wires Influence of supply voltage < 0.05 %/10 V maximum residual ripple 1 % U S (< 500 Hz) Maximum load Maximum permissible load R 910 Ω Z-20160_1 (HC) R( kω ) General characteristics signal refreshment rate Pt s ( signal change < 0.25 K/s) Thermocouples 0.2 s ( signal change < 2.5 K/s) Vibration resistance Vibration in operation 2g acc. to DIN IEC 68T.2-6 Resistance to shock acc. to DIN IEC 68T.2-27 Electrical isolation (I/O) 1.5 kv AC (60 s) Long-term stability 0.1 % p.a. Environment conditions Ambient temperature range C Transport and storage temperature C Relative humidity < 100 % Condensation Permitted 8,5 ( U smax U smin ) = ,4 Operation range V DC Power supply Us 30 Mechanical construction Dimensions Confer dimensional drawing Weight 250 g Housing material Polyamid Light grey (RAL 9002) Type of protection IP 20 (DIN 40050) Class of protection 2 (IEC 348) Class of combustibility V2 to V0 acc. to UL 94 Electrical connection Terminals, pluggable 2.5 mm 2, screw terminals Characteristics at rated conditions According to IEC 770 (related to 25 C) 1) Digital measured error Pt 100 ± 0.1 K Thermocouples ± 20 µv Linear resistance 500 Ω/5000 Ω ± 40 mω/200 mω Linear voltage 0 mv/00 mv ± 20 µv/50 µv D/A measured error ± 0.05 % of measuring span Additional influence of the internal reference junction Pt 100 DIN IEC 751 Kl. B Influences Influence of ambient temperature Pt 100/resistance measurement 2) < ( 0.05 % Thermocouple/mV 3) < ( 0.05 % ME ( Ω ) % ) 10 K MS ( Ω ) ME ( mv ) MS ( mv ) 0.01 % K 100 % ) 10 K MS ( K) Percentage related to measuring span MS = ME MA MA = lower range value, ME = upper range value 1) Percentage related to set measuring span Specified values corresponds to 3 σ (Gaussian normal distribution) 2) Pt 100 ( C): Influence of ambient temperature < (0.05 % %)/10 K = %/10 K 3) Type K ( C): Influence of ambient temperature < (0.05 % % %)/10 K = %/10 K 3

4 10/-8.54 EN Explosion protection Intrinsically safe Zone 1 Marking II 2 (1) G EEx [ia] ib IIC T6 EC-Type-Examination certificate PTB 99 ATEX 29 X Temperature class T6/T5/T4 50 C/65 C/85 C Supply circuit [ib] [ia] Max. voltage U i = 29.4 V U o = 5.6 V Short-circuit current I i = 0 ma I o = 1.5 ma 4) Max. power P i = 0.8 W P o = 20 mw Internal inductance L i = 0 µh L o = 1 mh Internal capacitance C i = 15 nf C o = 1.55 µf Zone 2 Marking II 3 G EEx n A II T6 Conformity statement PTB 99 ATEX 16 X Temperature class T6/T5/T4 50 C/65 C/85 C Electromagnetic compatibility (EMC) Pt 100: measuring range C, span 100 K Type of test Degree Influence IEC Burst to signal/ 3 kv < 0.1 % data lines Static discharge Contact plate (indirect) Terminals for supply 5) Terminals for sensors 5) 8 kv 6 kv 4 kv no influence no influence no influence Radiated field MHz...1 GHz 10 V/m < 1.0 % Coupling 150 khz - 80 MHz 10 V < 1.0 % According to NAMUR NE recommendation. In case of an input signal change > 0.25 K/s for Pt100 or > 2.5 K/s for thermocouples a measured value plausibility check is performed. 5) Air discharge (at 1 mm distance) 4) See 1. supplement PTB 99 ATEX 29 X 4

5 10/-8.54 EN Communication/parameterization Hand held terminal HHT 691HT, STT04, HHT275 CoMeter Hart conigurator and LC display Device Management Tool SV401 (SMART VISION) Parameter Sensor type, error signalling, measuring range, general characteristics (i. e. TAG number), damping, signal simulation of output Software interface AMS, Cornerstone CoMeter ABB TH102-Ex PTB 99 ATEX 29 X II 2 G EEx [ia] ib IIC T6 TA<=50 C Ex Elektr. Daten siehe EG-Baumusterprüfbesch. Kanal 1: PT 100-3L C Kanal 2: PT 100-3L C Line resistance GND (250 Ω min.)* (optional) Processinterface or Isolators Controller Recorders 1) or 691HT, STT04, HHT275 FSK Modem *if necessary Z-20162e 5

6 10/-8.54 EN Connection diagram 31 + Us= 8,5...30V DC 32 - Microprocessor Channel 1 Reference- Junction + - VDCV V VDC 41 + Us= 8,5...30V DC 42 - Microprocessor Channel 2 Reference- Junction + - VDCV V VDC a) b) c) d) e) f) g) h) i) For the 1 channel version view wiring diagram of channel 1 Z a) Resistance thermometer, 2 wire circuit b) Resistance thermometer, 3 wire circuit c) Resistance thermometer, 4 wire circuit d) Double resistance thermometer, 2 wire circuit (average value or differential temperature measurement) e) Potentiometer input, 4 wire circuit f) Thermocouple g) Double thermocouple (average value or differential temperature measurement) h) Voltage measurement i) Double voltage measurement (average value or differential temperature measurement) Dimensional diagram (Dimensions in mm) 99 ABB TH102-Ex PTB 99 ATEX 29 X II 2 G EEx [ia] ib IIC T6 TA<=50 C Ex Elektr. Daten siehe EG-Baumusterprüfbesch. Kanal 1: PT 100-3L C Kanal 2: PT 100-3L C Us= 8,5...30V DC Us= 8,5...30V DC Microprocessor Channel 1 Reference- Junction Microprocessor Channel 2 Reference- Junction a) b) c) d) e) VDCV V VDC VDCV V VDC f) g) h) i) 35,5 4,5 Z

7 10/-8.54 EN Ordering information Catalog No. EUR Deliv. time TH102/TH102-Ex V517- ex stock Without Explosion protection: TH102 1-channel 1 264,60 * TH102 2-channel 3 496,70 * With Explosion protection Zone 1 TH102-Ex 1-channel ATEX: II 2 (1) G EEx [ia]ib IIC T ,90 * TH102-Ex 2-channel ATEX: II 2 (1) G EEx [ia]ib IIC T ,30 * Zone 2 / type N TH102-Ex N 1-channel ATEX: II 3 G EEx n A II T6 N 291,90 * TH102-Ex N 2-channel ATEX: II 3 G EEx n A II T6 M 552,30 * Programming 1-channel Factory standard parameter 0 - Pt 100, C, 4 wire circut, damping off, direct action characteristic overranging at sensor or device error (.5 ma) Customer-specific parameter setting, one-channel version 1,50 * 2-channel Factory standard parameter 2 - Pt 100, C, 4 wire circuit, damping off, direct action characteristic overranging at sensor or device error (.5 ma) Customer-specific parameter setting, two-channel version 3 32,20 * Calibration certificates without 0-1-channel 2 point 1 75,60 * 1-channel 9 point 2 107,10 * 2-channels 2 point A 107,10 * 2-channels 9 point B 160,70 * Accessories Catalog No. EUR Deliv. time ABB FSK modem [EEx ib] IIC (parameter setting in the installation) see Data Sheet 10/ EN Device Management Tool SV401 (SMART VISION) see Data Sheet 10/ EN TH02/-102/-202 driver for AMS software 1.4 (Rosemount) 1) ,10 * 1) already integrated in AMS software version 5.0 or higher Notice: For a lokal programming on the desk can used as Hardware the universal FSK Programming-Set (without Parasoft). (see Data Sheet 10/ EN ordering information) 7

8 The Industrial IT wordmark and all mentioned product names in the form XXXXXX IT are registered or pending trademarks of ABB. ABB has Sales & Customer Support expertise in over 100 countries worldwide. The Company s policy is one of continuous product improvement and the right is reserved to modify the information contained herein without notice. Printed in the Fed. Rep. of Germany (10.02) ABB /-8.54 EN Rev. A ABB Ltd. Salterbeck Trading Estate Workington, Cumbria CA 5DS UK Tel: +44 (0) Fax: +44 (0) ABB Inc. 5 E. County Line Road Warminster, PA USA Tel: Fax: ABB Automation Products GmbH Borsigstr Alzenau Germany Tel: Fax: