How to Build a DMR Simulcast Network
|
|
- Cora Fields
- 6 years ago
- Views:
Transcription
1 How to Build a DMR Simulcast Network Workshop: Digital Mobile Radio Association DMR Alessandro Guido DMR System Design, Leonardo S.p.A. Augusto Colombo DMR Sales Technical Support, Leonardo S.p.A. 1
2 Broadcast: Simulcast vs Cellular F1, F2 F7, F8 F7, F8 F1, F2 F1, F2 F1, F2 F3, F4 SIMULCAST: same channel used by neighbouring RBSs, only 2 frequencies for the whole system F1, F2 F3, F4 F5, F6 F7, F8 CELLULAR: different channels used by neighbouring RBSs (cluster) 2
3 Simulcast Key Factors Issue: to manage radio communications in overlapping areas Solution: implementation of effective procedures for synchronisation, equalisation and voting Result: the radio network acts as a single virtual repeater synchronisation equalisation voting Virtual repeater MAIN BENEFITS: The coverage area is actually improved, compared to the repeaters single contributions. Only one frequency pair RF spectral efficiency cost savings for licensed frequencies Optimal coverage of wide areas Easy-to-use Same operations like under a single site repeater 3
4 Simulcast Key Points Single Virtual Repeater Wide area coverage Requires a low number of frequencies in the network Intrinsic call Hand-Over Network Coverage easy to be increased 4
5 General Hypotheses for a Radio Coverage Study When evaluating the radio coverage for a simulcast network, that uses multiple synchronized and interconnected repeaters, it is essential to know the following parameters: exact location of repeater sites (lat., long., height from sea level) antenna height from ground ( i.e. tower height) accuracy and resolution of the terrain, building, and clutter data propagation model used choice of time/location/margin values physical characteristics of the study area (plains, mountains, urban, etc.) allocated frequency bands radio electrical characteristics of the radio equipment used ( both fixed and terminal) radio electrical characteristics of the antenna equipment used ( both fixed and terminal) requested service: portable and/or mobile, outdoor and/or indoor, in-car and/or mobile Only by knowing all the above parameters it is possible to simulate with a good approximation the service area (radio coverage). The service area is where a level of radio signal able to ensure the requested service is guaranteed. Since the radio propagation can be described by a statistical process, this requirement is satisfied only with a certain probability, called location probability, where the signal level is enough to ensure the requested service in the service area REQUIREMENTS: a sufficient value of the local average RF power a given coverage probability 5
6 DMR Simulcast - Radio Coverage project guidelines standards These standards are intended to provide information that allows accurate and consistent modeling of coverage performance. These standards utilize specified and measured product performance and other sources that provide a sound engineering basis to the values suggested. Calculation hypotheses 1. Calculation of the average path loss in quasi-smooth terrain, no obstructions 2. Diffraction losses (orography), roughness of the terrain => database 3. Local territorial morphology, Land Use => database models and mathematics algorithm for radio coverage 4. Power Budget, evaluation of useful signal for communication; 5. Additional losses to reach the coverage probability for the requested service. Simulcast Delay Spread Simulation vs real coverage verification radio equipement radio coverage probability Hess method 6
7 Calculation Hypotheses - steps 1, 2 and 3 1. Calculation of the average path loss in quasi-smooth terrain (Okumura Hata/Davidson Ext.) TIA recommends in TSB-88 a modification of the Hata model to cover a wider range of input parameters. The output parameter of Olumura Hata/Davidson Extended algorithm is the average path loss LdB calculated according to the terrain type. In addition to this extension, this model can optionally include additional path loss due to reflections and diffraction loss from terrain obstacles. 2. Diffraction losses (orography) (Epstein Peterson Diffraction) Diffraction attenuation is due to orographic obstacles due to local territory morphologies. A rich and dedicated Digital Terrain Model (DTM) database can be used together with the Epstein and Peterson algorithm. Recommended resolution not less than 1 arcsec (~30 meters). 3. Added attenuation due to local territory morphologies Clutter Added attenuation due to local territory morphologies to take into account urban and suburban density, the type of herbaceous or woody vegetation, rocky areas, glaciers, etc. There are different databases that can be used: - Land Use and Land Cover (LULC) database from the United States Geological Survey (USGS) - CORINE (COoRdination of INformation on the Environment) Land Cover - European Urban Atlas: it provides reliable high-resolution land use maps for 305 Large Urban Zones (i.e. with more than inhabitants) and their surroundings. They incorporate different data formats and at least 15 classes; resolutions are up to 1 arcsec (~30 meters). 7
8 Calculation Hypotheses - step 3 - terrain database exmples Terrain Orography The Digital Elevation Model normally used has a resolution plan (XY) of about 50x50 meters, and a height resolution (Z) of about 10 meters, and is built specifically for the coverage prediction tool ROME 8
9 Calculation Hypotheses - step 3 - terrain database exmples Terrain Morphology The Clutter Land Use normally used reproduces the morphological classes of territory, with a resolution plan (XY) of about 50x50, meters Different colors are associated to different terrain use: Urban Atlas database ROME 9
10 Calculation Hypotheses - step 3 - terrain database exmples Terrain Morphology Land Use Land Cover (LULC) from United States Geological Survey (USGS) BOSTON 10
11 Calculation Hypotheses - steps 4 and 5 4. Link Budget calculation Link budget is the calculation of the local average power, usually corresponding to a 50% coverage probability, obtained by summing gains and losses related to TX RBS, RX RBS and terminals. Link budget calculation assures the correct balance between uplink (Talk-In) and downlink (Talk-Out) paths; its output is the maximum allowed attenuation. The worst case, i.e. the one with minimum path loss that still guarantee the communication is used to identify the coverage area, i.e. the service area where terminals can actually send and receive with high reliability and good quality. 4.1) Delivered Audio Quality DAQ (TIA TSB-88) These documents contain recommendations for both public safety and non-public safety performance that are intended be used in the modeling and simulation of these systems. These documents also satisfy the need for a standardized empirical measurement methodology that is useful for routine proof-ofperformance and acceptance testing and in dispute resolution of interference cases that might emerge. 5) Coverage reliability calculation (90 or 95%) Coverage reliability is assumed as a function of radio service. The recommended values are as follows: 11
12 Link Budget Calculation - 1 A mobile radio channel experiences short-term variations due to multipath fading. This has undesirable effects on the audio quality or BER of a wireless link. Propagation models of practical use do not predict this variation. Its impact is included within the sensitivity of the receiver via a parameter called the faded Cf/(I+N) ratio. This ratio depends on the modulation type, coding and error correction details and the rate of fading. The analysis process requires the following parameters: 1. Noise floor 2. Static carrier-to-noise ratio (Cs/N) 3. Required Cf/(I+N) (faded performance threshold) 4. Reliability margin In order to determine the noise floor of the receiver, subtract the static carrier-to-noise ratio (Cs/N) from the reference sensitivity (12 db SINAD Analog, 5% BER DMR Digital): reference sensitivity (DMR = -118dBm typical) _ Modulation Type Analog FM (12,5kHz) Cs/N (db) Source 7 db TSB-88 DMR 5.3dB TSB-88 12
13 Link Budget Calculation - 2 Determining the required faded carrier to interference plus noise ratio Cf/(I+N) at a given Delivered Audio Quality (DAQ): Modulation Type Analog FM (12,5kHz) DAQ 3.0 DAQ 3.4 DAQ 4.0 Source 23.0 db 26.0 db 33.0 db TSB-88 DMR 14.3dB 15.6dB 19.4dB TSB-88 Determining the faded performance threshold (e.g. for DAQ 3.4): Typical body loss (from ITU-R P.1406): -107,7dBm -118dBm Dynamic Threshold (Faded Performance Threshold) Static Threshold (Reference Sensitivity) Noise Floor Cf/(I+N) = 15,6dB Cs/N = 5,3dB 13
14 OL OL JE PV SU SU SU OL OL JE PV SU SU SU Link Budget Calculation - 3 Body loss and inc-ar loss down link Required Delivered Audio Quality Reference Sensitivity Faded Sensitivity Power Budget Talk OUT Power Budget Talk IN Channels Type Česká republika Česká republika Česká republika Česká republika Česká republika Česká republika Česká republika Range VHF VHF VHF VHF VHF VHF VHF Antenna TX RX #1 #1 #1 #1 #1 #1 #1 Antenna Type Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Model RF331NH RF331NH RF331NH RF331NH RF331NH RF331NH RF331NH Antenna Azimut N Antenna Cable Type Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Model LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN Antenna Height m Antenna Cable Length m DMR TX Power W 25,0 25,0 25,0 25,0 25,0 25,0 25,0 DMR TX Power dbmw 44,0 44,0 44,0 44,0 44,0 44,0 44,0 Combiner Loss db 0,00 0,00 0,00 0,00 0,00 0,00 0,00 Circulator Loss db 0,40 0,40 0,40 0,40 0,40 0,40 0,40 Jumper Loss db 0,60 0,60 0,60 0,60 0,60 0,60 0,60 Duplexer Loss db 1,20 1,20 1,20 1,20 1,20 1,20 1,20 TX Power W 15,1 15,1 15,1 15,1 15,1 15,1 15,1 Antenna Gain dbd Cable Loss db 2,38 1,72 1,87 1,09 1,72 1,44 1,72 TOTAL TX Inse. Loss db 4,58 3,92 4,07 3,29 3,92 3,64 3,92 ERP dbmw 43,4 44,1 43,9 44,7 44,1 44,3 44,1 ERP W 21,9 25,5 24,6 29,4 25,5 27,2 25,5 Portable Mobile Talk OUT Loss Path Loss TX Power W Antenna Gain dbd Refer. Sensitivity dbmw -118,0-118,0-118,0-118,0-118,0-118,0-118,0 Faded Sensitivity dbmw -107,7-107,7-107,7-107,7-107,7-107,7-107,7 TX Power W Antenna Gain dbd Refer. Sensitivity dbmw -118,0-118,0-118,0-118,0-118,0-118,0-118,0 Faded Sensitivity dbmw -107,7-107,7-107,7-107,7-107,7-107,7-107,7 Body Loss db In Car Loss db Buinding Loss db TOTAL Mar. Pt. IC db TOTAL Mar. Pt. OD db TOTAL Mar. Mb. db DownLink Pt. IC db 127,1 127,8 127,6 128,4 127,8 128,0 127,8 DownLink Pt. OD db 133,1 133,8 133,6 134,4 133,8 134,0 133,8 DownLink Mb. db 151,1 151,8 151,6 152,4 151,8 152,0 151,8 Portable IN CAR Talk OUT Signal Threshold Portable OUT DOOR Talk OUT Signal Threshold Mobile Talk OUT Signal Threshold dbmw dbmw dbmw -85,7-85,7-85,7-91,7-91,7-91,7-85,7-85,7-91,7-91,7-107,7-107,7-107,7-107,7-107,7-85,7-85,7-91,7-91,7-107,7-107,7 Channels Type Česká republika Česká republika Česká republika Česká republika Česká republika Česká republika Česká republika Range VHF VHF VHF VHF VHF VHF VHF Antenna TX RX #1 #1 #1 #1 #1 #1 #1 Antenna Type Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Omnidirez. Model RF331NH RF331NH RF331NH RF331NH RF331NH RF331NH RF331NH Antenna Azimut N Antenna Cable Type Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Cellflex 1/2" Model LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN LCF12-50JFN Antenna Height m Antenna Cable Length m DMR Refer. Sensitivity dbmw -118,0-118,0-118,0-118,0-118,0-118,0-118,0 DAQ 3.4 Faded Sensitivity dbmw -107,7-107,7-107,7-107,7-107,7-107,7-107,7 Combiner Loss db 0,00 0,00 0,00 0,00 0,00 0,00 0,00 Circulator Loss db 0,40 0,40 0,40 0,40 0,40 0,40 0,40 Jumper Loss db 0,60 0,60 0,60 0,60 0,60 0,60 0,60 Duplexer Loss db 1,20 1,20 1,20 1,20 1,20 1,20 1,20 RX Add. Loss db 0,0 0,0 0,0 0,0 0,0 0,0 0,0 Antenna Gain dbd Cable Loss db 2,38 1,72 1,87 1,09 1,72 1,44 1,72 TOTAL RX Inse. Loss db 4,58 3,92 4,07 3,29 3,92 3,64 3,92 Frequency Range VHF Portable Mobile Talk IN Loss Path Loss TX Power W Antenna Gain dbd Refer. Sensitivity dbmw -118,0-118,0-118,0-118,0-118,0-118,0-118,0 Faded Sensitivity dbmw -107,7-107,7-107,7-107,7-107,7-107,7-107,7 TX Power W Antenna Gain dbd Refer. Sensitivity dbmw -118,0-118,0-118,0-118,0-118,0-118,0-118,0 Faded Sensitivity dbmw -107,7-107,7-107,7-107,7-107,7-107,7-107,7 Body Loss db In Car Loss db Buinding Loss db TOTAL Mar. IC db TOTAL Mar. OD db TOTAL Mar. Mb. db UpLink Pt. IC db 126,1 126,8 126,6 127,4 126,8 127,1 126,8 UpLink Pt. OD db 132,1 132,8 132,6 133,4 132,8 133,1 132,8 UpLink Mb. db 147,1 147,8 147,6 148,4 147,8 148,1 147,8 Portable IN CAR Talk IN Signal Threshold Portable OUT DOOR Talk IN Signal Threshold Mobile Talk IN Signal Threshold dbmw -84,7-84,7-84,7 dbmw -103,7-103,7-103,7 Body loss and in-car loss up link dbmw -90,7-90,7-90,7-90,7-84,7-84,7-90,7-103,7-103,7-84,7-84,7-90,7-90,7-103,7-103,7 Talk Out Signal Threshold 28 November Worst case 2017 Talk In Signal Threshold 14
15 Coverage reliability calculation Coverage reliability is assumed as a function of radio service. The recommended values are as follows: Radio Service Faded Performance Threshold Public Safety DAQ 3.4 LMR DAQ 3.0 The reliability is the probability that the received local average signal strength predicted in a given tile equals or exceeds the desired Faded Performance Threshold. Link budget gives a 50% coverage probability to have a local average power better than the signal threshold. To have a much more accurate coverage probability, it is needed to take into account two others parameters: local average power statistical law: to find the space and time probability in which the signal level is above the required minimum level standard deviation: data dispersion from average value measurement normal distribution as a function of probability (ITU P. 1546) additional attenuation for local territorial morphology probability of coverage 50% + ( standard deviation on the local morphology x ) 15
16 DMR Simulcast Delay Spread - 1 Two signals transmitted at precisely the same time will arrive at a receiver at different times, depending on the distance that the signal travels. This difference in arrival times of the two signals time is known as delay. The combined effect of multiple signals in a simulcast environment can be computed using the "Delay Spread" factor. A method of quantifying modulation performance in simulcast and multipath environments is desired. Hess designed a model, called the multipath spread model. The model is based on the observation that for signal delays that are small with respect to the symbol time, the bit error rate (BER) observed is a function of RMS value of the time delays of the various signals weighted by their respective power levels. This delay spread represents the entire range of multipath possibilities to a single number. The multipath spread for N signals is given by: Since BER is affected by Tm more strongly than N, any value of N can be more simply represented as if it were due to two rays of equal signal strength. This would be interpreted as Tm can be calculated by evaluating for two signals, where P1 equals P2. The value for Tm is the absolute time difference in the arrival of the two signals. 16
17 DMR Simulcast Delay Spread - 2 In the simulcast delay spread Hess studies, two parameters are used: the Capture Margin and the Maximum Simulcast Delay Spread value: "Capture Margin": if any signal exceeds at least one from all the others by this value, then this single signal is the only one recognized by the receiver. If the capture margin criterion is not met, the delay spread value is computed with the multipath spread delay model "Maximum Simulcast Delay Spread (SDS)": it is the maximum permitted delay value. If the computed delay spread exceeds the maximum value, then the point is considered to have no usable signal. If the computed delay is less than the maximum specified delay, the signal at the point is the sum of the received power of the signals The delay spread capabilities of the various modulations are predominantly a function of the characteristics of that modulation. Given the delay spread capabilities of the various modulations, it is possible to predict system performance for the applicable modulation type and thereby design the system to meet coverage and propagation requirements. 17
18 DMR Simulcast Delay Spread - 3 Slave Master Slave Slave The whole simulcast-coverage area can be separated into two main types: capture areas: radio terminals receive a signal from only one transmitter (or where one signal only captures the receiver), non-capture (or overlap) areas: where the signal strength from adjacent transmitters is approximately equal In non-capture (or overlap) areas the delay made by the multipath from the two or more RBS toward the radio terminal must be simulated, controlled and adjusted to be non-destructive. 18
19 DMR Simulcast Delay Spread - 4 Hess described a method where multipath spread and the total signal power necessary for given BER criteria are plotted and used to determine coverage. BER (%) vs Multi-Path Spread (μs) The delay spread curves can be represented for various DAQ values, as the value of Tm is associated to the BER% and to the DAQ. TIA reported DAQ Scores DMR 2 slot TDMA (AMBE +2) Simulcast Performance Cf/N vs Multi-Path Spread (μs) BER (%) The loss of sensitivity becomes extreme as the delay spread increases. An important reference is the asymptote on the delay spread axis, which is the point at which it becomes impossible to meet the BER criterion independently of the signal strength. Another important reference for a modulation is the signal strength necessary for a given BER at Tm = 0 μs. Given these attributes, the delay performance of the candidate modulation is bounded. 19
20 DMR Simulcast Delay Spread - 5 Local reflectors Master Base Station Local reflectors Mobile d1 Slave Base Station d2 The delay spread can be expressed in a simplified way as: T ( d d ) 1 2 c
21 DMR Simulcast Delay Spread - 6 Launch time adjustment: The usual procedure is to delay the transmission of RBS that have a smaller coverage area versus others which have a bigger coverage area In this example, the transmission of BS 3 must be delayed according to: ( 1 2 d d ) 1000 c = t 21
22 DMR Simulcast Delay Spread in practice - 1 If the differences in travel times of the various paths are negligible compared to the symbol time, the signal components arrive at the receiver at the same time, leading to an increase in the intensity of the signal received by the sum of the components The higher the bit rate of the system, the lower the symbol time => the differences in arrival times can become significant compared to the symbol time itself. This effect creates destructive Inter Symbol Interference (ISI) due to the sum of the current symbol with echoes of previous symbols, with an adverse effect on system performance The ISI begins to degrade the BER when the delay spread is greater than 1/7 to 1/10 of symbol time DMR modulation has a symbol duration of µs, so attention has to be payed when the delay spread is higher than 20 to 30 µs 22
23 DMR Simulcast Delay Spread in practice - 2 To reduce the interference in the overlapping areas it is necessary to maintain the RMS delay spread at a value of less than 20 to 30 µsec To achieve this goal there are typically three means: by introducing a delay or an advance on the transmitted signal from RBS, this is achieved by changing Overlap Area Distance Compensation (OADC) parameters by changing the antenna bearing and kind (omnidirectional vs directional antenna) by changing the RF power level of the RBS (also with potential energy savings) The delay spread has higher impact in outdoor environments because multiple paths have more impact than in indoor environments 23
24 DMR Simulcast Delay Spread in practice - 3 Delay spread analysis should be performed within a distance range great enough (ideally infinity) to take into account also the RF field components from those RBS which, while not contributing to the communication (far more than the theoretical 75Km for DMR), can still contribute the delay spread Once completed, the static and dynamic analysis and solved the delay spread issue, it is necessary to verify that the new coverage allows the communication in all the user s area. This is because the changes due to the solution of the delay spread issue change the RF coverage of the system If needed, it is necessary to iterate the described procedure starting from the calculation of the link budget and correct the parameters (powers, delays, antenna bearings and types, etc.) so as to ensure RF coverage and solve the delay spread issue in the service area 24
25 DMR Simulcast Delay Spread - simulation examples 1 Performance for DAQ = 3.4 (BER = 2.0%) delay offset for equalized map The Signal Delay Spread (SDS) capability is the amount of delay between two independently faded equal amplitude signals that can be tolerated, when the standard input signal is applied through a faded channel simulator that will result in the standard BER at the receiver detector. The channel simulator provides a composite signal of two, equal amplitude, independently faded rays, the last of which is a delayed version of the first. 25
26 DMR Simulcast Delay Spread - simulation examples 2 26
27 Thank you! For more info: 27
28 I M P R E S S U M PMRExpo bis 30. November 2017 in Köln Veranstalter und Herausgeber EW Medien und Kongresse GmbH Kleyerstr Frankfurt am Main November 2017 Copyright: Das Werk einschließlich aller seiner Teile ist urheberrechtlich geschützt. Jede Verwertung außerhalb der engen Grenzen des Urheberrechtsgesetzes ist ohne Zustimmung des Verlages unzulässig und strafbar. Das gilt vor allem für Vervielfältigungen in irgendeiner Form (Fotokopie, Mikrokopie oder ein anderes Verfahren), Übersetzung und die Einspeicherung und Verarbeitung in elektronischen Systemen.
Radio Coverage Studies for DMR Simulcast Systems
Radio Coverage Studies for DMR Simulcast Systems Workshop: Digital Mobile Radio Association DMR Alessandro Guido DMR System Design, Leonardo S.p.A. Augusto Colombo DMR Sales Technical Support, Leonardo
More informationEuropean PMR Communication Session What s happening in UK?
European PMR Communication Session What s happening in UK? Peter Clemons Founder & Managing Director, Quixoticity Kolnemesse, Kӧln November 24, 2015 11/24/2015 1 Quixoticity? Clemons Consulting dedicated
More informationCoverage Impact of Implementing Narrowband Equipment. Bernie Olson Chair TIA TR8.18
Coverage Impact of Implementing Narrowband Equipment Bernie Olson Chair TIA TR8.18 It Depends ON Lots of variables to take into consideration Migration process Link Budget Tradeoff of sensitivity and interference
More informationInformation on the Evaluation of VHF and UHF Terrestrial Cross-Border Frequency Coordination Requests
Issue 1 May 2013 Spectrum Management and Telecommunications Technical Bulletin Information on the Evaluation of VHF and UHF Terrestrial Cross-Border Frequency Coordination Requests Aussi disponible en
More informationSimulcasting Project 25
ATLAS Simulcasting Project 25 2013 April Copyright 2012-2013 by EFJohnson Technologies, Inc. The EFJohnson Technologies logo, ATLAS, and StarGate are trademarks of EFJohnson Technologies, Inc. All other
More informationPMR in France Shift towards LTE
PMR in France Shift towards LTE PMRexpo 2015 Cologne, the 24th of November 2015 Agenda PMR market Overview Shifting towards LTE Zoom on indoor PMR market Overview Shifting towards LTE Zoom on indoor The
More informationRevision of Lecture One
Revision of Lecture One System blocks and basic concepts Multiple access, MIMO, space-time Transceiver Wireless Channel Signal/System: Bandpass (Passband) Baseband Baseband complex envelope Linear system:
More informationLinking Narrowband to Broadband Networks (TETRA -Mission Critical LTE Interworking) PMRexpo Workshop, 28 Nov 2017, Cologne, Germany
Linking Narrowband to Broadband Networks (TETRA -Mission Critical LTE Interworking) PMRexpo Workshop, 28 Nov 2017, Cologne, Germany What are the important aspects for an operator? Topics What is the status
More informationPROPAGATION MODELING 4C4
PROPAGATION MODELING ledoyle@tcd.ie 4C4 http://ledoyle.wordpress.com/temp/ Classification Band Initials Frequency Range Characteristics Extremely low ELF < 300 Hz Infra low ILF 300 Hz - 3 khz Ground wave
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2003 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationRevision of Lecture One
Revision of Lecture One System block Transceiver Wireless Channel Signal / System: Bandpass (Passband) Baseband Baseband complex envelope Linear system: complex (baseband) channel impulse response Channel:
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2004 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationECE 476/ECE 501C/CS Wireless Communication Systems Winter Lecture 6: Fading
ECE 476/ECE 501C/CS 513 - Wireless Communication Systems Winter 2005 Lecture 6: Fading Last lecture: Large scale propagation properties of wireless systems - slowly varying properties that depend primarily
More informationAtoll. SPM Calibration Guide. RF Planning and Optimisation Software. Version AT271_MCG_E2
Atoll RF Planning and Optimisation Software Version 2.7.1 SPM Calibration Guide AT271_MCG_E2 Contact Information Forsk (Head Office) 7 rue des Briquetiers 31700 Blagnac France www.forsk.com sales@forsk.com
More informationEvaluation of Power Budget and Cell Coverage Range in Cellular GSM System
Evaluation of Power Budget and Cell Coverage Range in Cellular GSM System Dr. S. A. Mawjoud samialmawjoud_2005@yahoo.com Abstract The paper deals with study of affecting parameters on the communication
More informationRoger Kane Managing Director, Vicom Australia
Understanding and testing of DMR standard Roger Kane Managing Director, Vicom Australia @CommsConnectAus#comms2014 Presentation Title: Understanding and Testing DMR Speaker: Roger Kane @CommsConnectAus
More informationSupporting Network Planning Tools II
Session 5.8 Supporting Network Planning Tools II Roland Götz LS telcom AG / Spectrocan 1 Modern Radio Network Planning Tools Radio Network Planning Tool Data / Result Output Data Management Network Processor
More informationPropagation Modelling White Paper
Propagation Modelling White Paper Propagation Modelling White Paper Abstract: One of the key determinants of a radio link s received signal strength, whether wanted or interfering, is how the radio waves
More informationSpecifying, predicting and testing:
Specifying, predicting and testing: Three steps to coverage confidence on your digital radio network EXECUTIVE SUMMARY One of the most important properties of a radio network is coverage. Yet because radio
More informationThe Radio Channel. COS 463: Wireless Networks Lecture 14 Kyle Jamieson. [Parts adapted from I. Darwazeh, A. Goldsmith, T. Rappaport, P.
The Radio Channel COS 463: Wireless Networks Lecture 14 Kyle Jamieson [Parts adapted from I. Darwazeh, A. Goldsmith, T. Rappaport, P. Steenkiste] Motivation The radio channel is what limits most radio
More informationSmall-Scale Fading I PROF. MICHAEL TSAI 2011/10/27
Small-Scale Fading I PROF. MICHAEL TSAI 011/10/7 Multipath Propagation RX just sums up all Multi Path Component (MPC). Multipath Channel Impulse Response An example of the time-varying discrete-time impulse
More informationAtoll SPM (Standard Propagation Model) calibration guide
Atoll SPM (Standard Propagation Model) calibration guide January 2004 FORSK 7 rue des Briquetiers 31700 BLAGNAC France www.forsk.com SARL au capital de 150 000 - RCS Toulouse 87 B 1302 - SIRET 342 662
More informationSimulcast Radio Network Design. Jay M. Jacobsmeyer, P.E. Pericle Communications Co Vindicator Drive, Suite 100 Colorado Springs, CO 80919
Simulcast Radio Network Design Jay M. Jacobsmeyer, P.E. Pericle Communications Co. 1910 Vindicator Drive, Suite 100 Colorado Springs, CO 80919 Outline Company Overview Background Information Needs Analysis
More information1 Minimum usable field strength
1 RECOMMENDATION ITU-R BS.412-8* PLANNING STANDARDS FOR FM SOUND BROADCASTING AT VHF (Questions ITU-R 74/1 and ITU-R 11/1) (1956-1959-1963-1974-1978-1982-1986-199-1994-1995-1998) The ITU Radiocommunication
More informationIntroduction. TV Coverage and Interference, February 06, 2004.
A New Prediction Model for M/H Mobile DTV Service Prepared for OMVC June 28, 2011 Charles Cooper, du Treil, Lundin & Rackley, Inc. Victor Tawil, National Association of Broadcasters Introduction The Open
More informationRECOMMENDATION ITU-R BS
Rec. ITU-R BS.1194-1 1 RECOMMENDATION ITU-R BS.1194-1 SYSTEM FOR MULTIPLEXING FREQUENCY MODULATION (FM) SOUND BROADCASTS WITH A SUB-CARRIER DATA CHANNEL HAVING A RELATIVELY LARGE TRANSMISSION CAPACITY
More informationOptimizing 16 db Capture Effect to Overcome Class A 'Channelized' Signal Booster Group Delay problems within Public Safety Communications Systems
Optimizing 16 db Capture Effect to Overcome Class A 'Channelized' Signal Booster Group Delay problems within Public Safety Communications Systems July 30, 2008 2008 Jack Daniel Company 2008 Jack Daniel
More informationChapter 1: Telecommunication Fundamentals
Chapter 1: Telecommunication Fundamentals Block Diagram of a communication system Noise n(t) m(t) Information (base-band signal) Signal Processing Carrier Circuits s(t) Transmission Medium r(t) Signal
More informationMobile Radio Wave propagation channel- Path loss Models
Mobile Radio Wave propagation channel- Path loss Models 3.1 Introduction The wireless Communication is one of the integral parts of society which has been a focal point for sharing information with different
More information3GPP TR V7.0.0 ( )
TR 25.816 V7.0.0 (2005-12) Technical Report 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; UMTS 900 MHz Work Item Technical Report (Release 7) The present document
More informationSimulation of Outdoor Radio Channel
Simulation of Outdoor Radio Channel Peter Brída, Ján Dúha Department of Telecommunication, University of Žilina Univerzitná 815/1, 010 6 Žilina Email: brida@fel.utc.sk, duha@fel.utc.sk Abstract Wireless
More informationInternational Journal of Engineering and Technology Volume 3 No. 6, June, 2013
International Journal of Engineering and Technology Volume 3 No. 6, June, 2013 Spectrum Compatibility Study of Terrestrial Digital Audio Broadcasting System and the Microwave Radio Relay Links in the L-Band
More information1/27. White Paper June Signal propagation modeling In Urban Environment. Emmanuel Grenier
1/27 White Paper June 2005 Signal propagation modeling In Urban Environment Emmanuel Grenier 2/27 Signal propagation modeling in Urban Environment When working with ICS Telecom to simulate wireless propagation
More informationiq.link Key Features Comsearch A CommScope Company
2016 iq.link Key Features Comsearch A CommScope Company Table of Contents Near and Non-Line of Sight (nlos) Propagation Model:... 2 Radio State Analysis Graphics... 3 Comprehensive support for Adaptive
More informationNXDN Signal and Interference Contour Requirements An Empirical Study
NXDN Signal and Interference Contour Requirements An Empirical Study Icom America Engineering December 2007 Contents Introduction Results Analysis Appendix A. Test Equipment Appendix B. Test Methodology
More informationAntennas & Propagation. CSG 250 Fall 2007 Rajmohan Rajaraman
Antennas & Propagation CSG 250 Fall 2007 Rajmohan Rajaraman Introduction An antenna is an electrical conductor or system of conductors o Transmission - radiates electromagnetic energy into space o Reception
More informationTechnical Support to Defence Spectrum LTE into Wi-Fi Additional Analysis. Definitive v1.0-12/02/2014. Ref: UK/2011/EC231986/AH17/4724/V1.
Technical Support to Defence Spectrum LTE into Wi-Fi Additional Analysis Definitive v1.0-12/02/2014 Ref: UK/2011/EC231986/AH17/4724/ 2014 CGI IT UK Ltd 12/02/2014 Document Property Value Version v1.0 Maturity
More informationAdjacent Channel Studies in the FM Band
Adjacent Channel Studies in the FM Band Prepared for the NRSC By ibiquity Digital Corporation 11/09/00 Adjacent Channel Studies in the FM Band Page 1 As part of its AM IBOC development effort, ibiquity
More informationWHITEPAPER IMPRovIng THE safety And EFFEcTIvEnEss of TETRA RAdIo users THRougH IncREAsEd RAdIo sensitivity And PoWER
MAY 2012 IMPROVING THE SAFETY AND EFFECTIVENESS OF TETRA RADIO USERS THROUGH INCREASED RADIO SENSITIVITY AND POWER 2dB or not 2dB, that is the question * *Hamlet s guide to radio planning Introduction
More informationKing Fahd University of Petroleum & Minerals Computer Engineering Dept
King Fahd University of Petroleum & Minerals Computer Engineering Dept COE 543 Mobile and Wireless Networks Term 0 Dr. Ashraf S. Hasan Mahmoud Rm -148-3 Ext. 174 Email: ashraf@ccse.kfupm.edu.sa 4//003
More informationMulti-Path Fading Channel
Instructor: Prof. Dr. Noor M. Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office), 186 (Lab) Fax: +9
More informationLevel 6 Graduate Diploma in Engineering Wireless and mobile communications
9210-119 Level 6 Graduate Diploma in Engineering Wireless and mobile communications Sample Paper You should have the following for this examination one answer book non-programmable calculator pen, pencil,
More informationTESTING OF FIXED BROADBAND WIRELESS SYSTEMS AT 5.8 GHZ
To be presented at IEEE Denver / Region 5 Conference, April 7-8, CU Boulder, CO. TESTING OF FIXED BROADBAND WIRELESS SYSTEMS AT 5.8 GHZ Thomas Schwengler Qwest Communications Denver, CO (thomas.schwengler@qwest.com)
More informationRadio Path Prediction Software
Radio Path Prediction Software for Command and Control Scenario Developers Reference# C-168, Michael Shattuck Command and Control Research and Technology Symposium June 2006 Topics Link Planning for Wireless
More informationCHAPTER 2 WIRELESS CHANNEL
CHAPTER 2 WIRELESS CHANNEL 2.1 INTRODUCTION In mobile radio channel there is certain fundamental limitation on the performance of wireless communication system. There are many obstructions between transmitter
More informationChannel Models. Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1
Channel Models Spring 2017 ELE 492 FUNDAMENTALS OF WIRELESS COMMUNICATIONS 1 Narrowband Channel Models Statistical Approach: Impulse response modeling: A narrowband channel can be represented by an impulse
More informationPoint to point Radiocommunication
Point to point Radiocommunication SMS4DC training seminar 7 November 1 December 006 1 Technical overview Content SMS4DC Software link calculation Exercise 1 Point-to-point Radiocommunication Link A Radio
More informationChannel Modelling ETIM10. Propagation mechanisms
Channel Modelling ETIM10 Lecture no: 2 Propagation mechanisms Ghassan Dahman \ Fredrik Tufvesson Department of Electrical and Information Technology Lund University, Sweden 2012-01-20 Fredrik Tufvesson
More informationChannel. Muhammad Ali Jinnah University, Islamabad Campus, Pakistan. Multi-Path Fading. Dr. Noor M Khan EE, MAJU
Instructor: Prof. Dr. Noor M. Khan Department of Electronic Engineering, Muhammad Ali Jinnah University, Islamabad Campus, Islamabad, PAKISTAN Ph: +9 (51) 111-878787, Ext. 19 (Office), 186 (Lab) Fax: +9
More informationPath-loss and Shadowing (Large-scale Fading) PROF. MICHAEL TSAI 2015/03/27
Path-loss and Shadowing (Large-scale Fading) PROF. MICHAEL TSAI 2015/03/27 Multipath 2 3 4 5 Friis Formula TX Antenna RX Antenna = 4 EIRP= Power spatial density 1 4 6 Antenna Aperture = 4 Antenna Aperture=Effective
More informationMitigating Interference & Maximizing Throughput in 700MHz for SCADA
Mitigating Interference & Maximizing Throughput in 700MHz for SCADA Paul Reid and Kathy Shaft (GRE) October 2018 WAS SPUN OUT OF 2 3 Phoenix US Headquarters US Headquarters Technical Support Hub Repair
More informationUNIK4230: Mobile Communications Spring 2013
UNIK4230: Mobile Communications Spring 2013 Abul Kaosher abul.kaosher@nsn.com Mobile: 99 27 10 19 1 UNIK4230: Mobile Communications Propagation characteristis of wireless channel Date: 07.02.2013 2 UNIK4230:
More informationWCDMA Mobile Internet in High-Mobility Environment Case Study on Military Operations of the Royal Thai Armed Forces
ontree Sungkasap, Settapong alisuwan and Vichate Ungvichian WCDA obile Internet in High-obility Environment Case Study on ilitary Operations of the Royal Thai Armed Forces General ontree Sungkasap 1, Colonel
More informationEC 551 Telecommunication System Engineering. Mohamed Khedr
EC 551 Telecommunication System Engineering Mohamed Khedr http://webmail.aast.edu/~khedr 1 Mohamed Khedr., 2008 Syllabus Tentatively Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week
More informationRECOMMENDATION ITU-R SF.1719
Rec. ITU-R SF.1719 1 RECOMMENDATION ITU-R SF.1719 Sharing between point-to-point and point-to-multipoint fixed service and transmitting earth stations of GSO and non-gso FSS systems in the 27.5-29.5 GHz
More informationUNIVERSITY OF TECHNOLOGY, SYNDEY
Cover Page - Type B: THIS PAPER MUST NOT BE REMOVED FROM EXAM CENTRE TO BE RETURNED AT THE END OF THE EXAMINATION UNIVERSITY OF TECHNOLOGY, SYNDEY SURNAME: FIRST NAME: STUDENT NO: COURSE: AUTUMN SEMESTER
More informationDerivation of Power Flux Density Spectrum Usage Rights
DDR PFD SURs 1 DIGITAL DIVIDEND REVIEW Derivation of Power Flux Density Spectrum Usage Rights Transfinite Systems Ltd May 2008 DDR PFD SURs 2 Document History Produced by: John Pahl Transfinite Systems
More informationWireless Physical Layer Concepts: Part III
Wireless Physical Layer Concepts: Part III Raj Jain Professor of CSE Washington University in Saint Louis Saint Louis, MO 63130 Jain@cse.wustl.edu These slides are available on-line at: http://www.cse.wustl.edu/~jain/cse574-08/
More informationCOMPATIBILITY AND SHARING ANALYSIS BETWEEN DVB T AND TALKBACK LINKS IN BANDS IV AND V
European Radiocommunications Committee (ERC) within the European Conference of Postal and Telecommunications Administrations (CEPT) COMPATIBILITY AND SHARING ANALYSIS BETWEEN DVB T AND TALKBACK LINKS IN
More informationADJACENT BAND COMPATIBILITY OF 400 MHZ TETRA AND ANALOGUE FM PMR AN ANALYSIS COMPLETED USING A MONTE CARLO BASED SIMULATION TOOL
European Radiocommunications Committee (ERC) within the European Conference of Postal and Telecommunications Administrations (CEPT) ADJACENT BAND COMPATIBILITY OF 400 MHZ AND ANALOGUE FM PMR AN ANALYSIS
More informationPlanning Parameters for DRM Mode E ( DRM+ )
German DRM Platform - DRM+ Technical Expert Group - Planning Parameters for DRM Mode E ( DRM+ ) concerning the use in VHF bands I, II and III V 3.0 04/05/2011 TABLE OF CONTENTS 1 Scope... 4 2 Reception
More information03_57_104_final.fm Page 97 Tuesday, December 4, :17 PM. Problems Problems
03_57_104_final.fm Page 97 Tuesday, December 4, 2001 2:17 PM Problems 97 3.9 Problems 3.1 Prove that for a hexagonal geometry, the co-channel reuse ratio is given by Q = 3N, where N = i 2 + ij + j 2. Hint:
More informationSingle Frequency Network Structural Aspects & Practical Field Considerations
Single Frequency Structural Aspects & Practical Field Considerations November 2011 Featuring GatesAir s Rich Redmond Chief Product Officer Copyright 2015 GatesAir, Inc. All rights reserved. Single frequency
More informationProject = An Adventure : Wireless Networks. Lecture 4: More Physical Layer. What is an Antenna? Outline. Page 1
Project = An Adventure 18-759: Wireless Networks Checkpoint 2 Checkpoint 1 Lecture 4: More Physical Layer You are here Done! Peter Steenkiste Departments of Computer Science and Electrical and Computer
More informationRadio Propagation Fundamentals
Radio Propagation Fundamentals Concept of Electromagnetic Wave Propagation Mechanisms Modes of Propagation Propagation Models Path Profiles Link Budget Fading Channels Electromagnetic (EM) Waves EM Wave
More informationP25 C4FM & LSM SIMULCAST TESTING WITHOUT SYSTEM INFRASTRUCTURE YOSEMITE NATIONAL PARK
P25 C4FM & LSM SIMULCAST TESTING WITHOUT SYSTEM INFRASTRUCTURE YOSEMITE NATIONAL PARK Tom Eckels, P.E. Hatfield & Dawson Consulting Engineers 9500 Greenwood Avenue N. Seattle, WA 98103 (206) 783-9151 18
More informationDigital Audio Broadcasting Eureka-147. Minimum Requirements for Terrestrial DAB Transmitters
Digital Audio Broadcasting Eureka-147 Minimum Requirements for Terrestrial DAB Transmitters Prepared by WorldDAB September 2001 - 2 - TABLE OF CONTENTS 1 Scope...3 2 Minimum Functionality...3 2.1 Digital
More informationLink Budget Calculation
Link Budget Calculation Training materials for wireless trainers This 60 minute talk is about estimating wireless link performance by using link budget calculations. It also introduces the Radio Mobile
More informationApplication Note 37. Emulating RF Channel Characteristics
Application Note 37 Emulating RF Channel Characteristics Wireless communication is one of the most demanding applications for the telecommunications equipment designer. Typical signals at the receiver
More informationHow to Conduct a Drive Test Survey
How to Conduct a Drive Test Survey Presented By: Jay M. Jacobsmeyer, P.E. George W. Weimer, P.E. Pericle Communications Company Trott Communications Group 1910 Vindicator Drive, Suite 100 4320 N. Beltline
More informationRadio propagation modeling on 433 MHz
Ákos Milánkovich 1, Károly Lendvai 1, Sándor Imre 1, Sándor Szabó 1 1 Budapest University of Technology and Economics, Műegyetem rkp. 3-9. 1111 Budapest, Hungary {milankovich, lendvai, szabos, imre}@hit.bme.hu
More informationECC Report 276. Thresholds for the coordination of CDMA and LTE broadband systems in the 400 MHz band
ECC Report 276 Thresholds for the coordination of CDMA and LTE broadband systems in the 400 MHz band 27 April 2018 ECC REPORT 276 - Page 2 0 EXECUTIVE SUMMARY This Report provides technical background
More informationRECOMMENDATION ITU-R F.1819
Rec. ITU-R F.1819 1 RECOMMENDATION ITU-R F.1819 Protection of the radio astronomy service in the 48.94-49.04 GHz band from unwanted emissions from HAPS in the 47.2-47.5 GHz and 47.9-48.2 GHz bands * (2007)
More informationNATIONAL INSTITUTE OF TECHNOLOGY, Arunachal Pradesh
NATIONAL INSTITUTE OF TECHNOLOGY, Arunachal Pradesh (Established by Ministry of Human Resources Development, Govt. Of India) Yupia, District-Papum Pare, Arunachal Pradesh -791112. M.Techl20I End-semester
More informationIEEE C a-01/09. IEEE Broadband Wireless Access Working Group <
Project IEEE 82.16 Broadband Wireless Access Working Group Title Coexistence between point to point links and PMP systems (revision 1) Date Submitted Source(s) Re: Abstract Purpose
More informationRF GUIDELINES MHz THE ERICSSON GSM SYSTEM R8
RF GUIDELINES 1800 MHz THE ERICSSON GSM SYSTEM R8 Ericsson Radio Systems AB 2000 The contents of this product are subject to revision without notice due to continued progress in methodology, design and
More informationGTBIT ECE Department Wireless Communication
Q-1 What is Simulcast Paging system? Ans-1 A Simulcast Paging system refers to a system where coverage is continuous over a geographic area serviced by more than one paging transmitter. In this type of
More information8800SX DMR Repeater Test Option 06
8800SX DMR Repeater Test Option 06 DMR Repeater Test Option The DMR Repeater test option allows testing of a DMR Repeater that is in conventional DMR Mode. Trunking or analog configurations are not supported.
More informationAbstract. Propagation tests for land-mobile radio service
Abstract Propagation tests for land-mobile radio service VHF (200MHz) and UHF (453, 922, 1310, 1430, 1920MHz) Various situations of irregular terrain/environmental clutter The results analyzed statistically
More informationNetwork Design Considerations and Deployment Concerns for a Ground Aircraft Communication System
Network Design Considerations and Deployment Concerns for a Ground Aircraft Communication System CelPlan Technologies Leonhard Korowajczuk CEO/CTO Leonhard @celplan.com 703-259-4022 www.celplan.com 9/10/2013
More informationRF Engineering Training
RF Engineering Training RF Engineering Training Boot Camp, RF Engineering Bootcamp is the unique answer to your RF planning, design and engineering in any wireless networks needs. RF Engineering Training,
More informationReview of Path Loss models in different environments
Review of Path Loss models in different environments Mandeep Kaur 1, Deepak Sharma 2 1 Computer Scinece, Kurukshetra Institute of Technology and Management, Kurukshetra 2 H.O.D. of CSE Deptt. Abstract
More informationUnit-1 The Cellular Concept
Unit-1 The Cellular Concept 1.1 Introduction to Cellular Systems Solves the problem of spectral congestion and user capacity. Offer very high capacity in a limited spectrum without major technological
More informationRECOMMENDATION ITU-R P Guide to the application of the propagation methods of Radiocommunication Study Group 3
Rec. ITU-R P.1144-2 1 RECOMMENDATION ITU-R P.1144-2 Guide to the application of the propagation methods of Radiocommunication Study Group 3 (1995-1999-2001) The ITU Radiocommunication Assembly, considering
More informationContents. Telecom Service Chae Y. Lee. Data Signal Transmission Transmission Impairments Channel Capacity
Data Transmission Contents Data Signal Transmission Transmission Impairments Channel Capacity 2 Data/Signal/Transmission Data: entities that convey meaning or information Signal: electric or electromagnetic
More informationChapter 2 Channel Equalization
Chapter 2 Channel Equalization 2.1 Introduction In wireless communication systems signal experiences distortion due to fading [17]. As signal propagates, it follows multiple paths between transmitter and
More informationDavid Tipper. Graduate Telecommunications and Networking Program
Wireless Communication Fundamentals David Tipper Associate Professor Graduate Telecommunications and Networking Program University it of Pittsburgh Telcom 2700 Slides 2 Wireless Networks Wireless Wide
More informationAdvanced Communication Systems -Wireless Communication Technology
Advanced Communication Systems -Wireless Communication Technology Dr. Junwei Lu The School of Microelectronic Engineering Faculty of Engineering and Information Technology Outline Introduction to Wireless
More informationFM Transmission Systems Course
FM Transmission Systems Course Course Description An FM transmission system, at its most basic level, consists of the transmitter, the transmission line and antenna. There are many variables within these
More informationGUIDELINES With elements of technical solution depending on the nature of radiocommunication service
GUIDELINES With elements of technical solution depending on the nature of radiocommunication service Technical solution within the application form for the issuance of an individual licence for the use
More informationSession2 Antennas and Propagation
Wireless Communication Presented by Dr. Mahmoud Daneshvar Session2 Antennas and Propagation 1. Introduction Types of Anttenas Free space Propagation 2. Propagation modes 3. Transmission Problems 4. Fading
More informationProtection Ratio Calculation Methods for Fixed Radiocommunications Links
Protection Ratio Calculation Methods for Fixed Radiocommunications Links C.D.Squires, E. S. Lensson, A. J. Kerans Spectrum Engineering Australian Communications and Media Authority Canberra, Australia
More informationUnit 3 - Wireless Propagation and Cellular Concepts
X Courses» Introduction to Wireless and Cellular Communications Unit 3 - Wireless Propagation and Cellular Concepts Course outline How to access the portal Assignment 2. Overview of Cellular Evolution
More informationCellular Expert Radio Links module features
Cellular Expert Radio Links module features Tasks Features Network data management Site, sector, construction, customer, repeater management: Add Edit Move Copy Delete Site re-use patterns for nominal
More informationM Y R E V E A L - C E L L U L A R
M Y R E V E A L - C E L L U L A R The hexagon cell shape If we have two BTSs with omniantennas and we require that the border between the coverage area of each BTS is the set of points where the signal
More informationOFDMA Networks. By Mohamad Awad
OFDMA Networks By Mohamad Awad Outline Wireless channel impairments i and their effect on wireless communication Channel modeling Sounding technique OFDM as a solution OFDMA as an improved solution MIMO-OFDMA
More informationIntegrated Mission-Critical Network Planning Using EDX SignalPro
Integrated Mission-Critical Network Planning Using EDX SignalPro Integrated Mission-Critical Network Planning Using SignalPro Steve Webster Director of Sales Engineering EDX Wireless, Inc. (www.edx.com)
More informationIEEE c-01/39. IEEE Broadband Wireless Access Working Group <
Project Title Date Submitted IEEE 802.16 Broadband Wireless Access Working Group Analysis and calculations of re-use factors and ranges for OFDMA in comparison to TDMA systems 2001-03-08
More informationTechnical Annex. This criterion corresponds to the aggregate interference from a co-primary allocation for month.
RKF Engineering Solutions, LLC 1229 19 th St. NW, Washington, DC 20036 Phone 202.463.1567 Fax 202.463.0344 www.rkf-eng.com 1. Protection of In-band FSS Earth Stations Technical Annex 1.1 In-band Interference
More informationSC - Single carrier systems One carrier carries data stream
Digital modulation SC - Single carrier systems One carrier carries data stream MC - Multi-carrier systems Many carriers are used for data transmission. Data stream is divided into sub-streams and each
More information