PANELMDP Main Distribution Panel. Descriptions Energy Efficient Transformer

Transcription

1 PANELMDP Main Distribution Panel Eaton Corp Catalog Number Manufacturer Description Weight per unit Product Category Descriptions Product Type PANELMDP Eaton Corp 1.0 (lbs/each) Three Phase Energy Efficient D Energy Efficient Transformer Manufacturer Information Brand EATON CUTLER-HAMMER GTIN Manufacturers Part Number V9MT1EE UPC Availability Manufacturer Status Packaging Carton 1 Weight Per each 1 Non-Stock

2 .1 Transformers Type DT-3 Contents Description Features, Benefits and Functions Standards and Certifications Catalog Number Selection Product Selection Single-Phase Aluminum Single-Phase Copper Single-Phase Shielded Aluminum Single-Phase Shielded Copper Three-Phase Aluminum Three-Phase Copper Three-Phase Shielded Aluminum Three-Phase Shielded Copper Accessories Technical Data and Specifications K-Factor Aluminum Copper Page V-T-3 V-T-3 V-T-4 V-T-4 V-T-4 V-T-6 V-T-8 V-T-10 V-T-1 V-T-3 V-T-34 V-T-4 V-T-50 V-T-50 V-T-51 V-T-5 V-T-57 Product Description Note: The following pages provide listings for most standard transformer ratings and styles. For other ratings or styles not shown, or for special enclosure types (including stainless steel), refer to Eaton. Types DS-3, DT-3 Ventilated, NEMA enclosure standard Suitable for indoor applications, outdoors when weathershields are also installed Upright mounting only 0ºC 150ºC rise standard; 115 C or 80 C rise optional Available in single-phase ratings , 600 volts primary (DS-3) Available in three-phase ratings and up to 600 volts primary (DT-3) Application Description NEMA TP-1-00 compliant energy-efficient transformers are specifically designed to meet the energy efficiency standards set forth in NEMA Standards publication, TP-1-00, Guide for Determining Energy Efficiency for Distribution Surveys have shown that the average loading of low voltage dry-type distribution transformers, over a 4-hour period, is approximately 35%. NEMA TP-1 compliant transformers are optimized to offer maximum efficiency at 35% of nameplate rating. The range of products covered by NEMA TP-1-00 are: NEMA TP-1-00 Product Range Voltage Rating Class Dry-Type Rating Liquid Rating Primary voltage Secondary voltage Single-phase Three-phase Single-phase Three-phase Voltage 34.5 kv and below 600V and below Transformers that are currently specifically excluded from the scope of NEMA Standard TP-1-00 include: Liquid-filled transformers below 10 Dry-type transformers below 15 AC and DC drives transformers Rectifier transformers designed for high harmonics Autotransformers Non-distribution transformers, such as UPS transformers Special impedance or regulation transformers Regulating transformers Sealed and non-ventilated transformers Machine tool transformers Welding transformers Transformers with tap ranges greater than 15% Transformers with a frequency other than 60 Hz Grounding transformers Testing transformers Efficiency levels set forth in NEMA TP NEMA TP-1-00 Efficiency Levels Tables of Energy Efficiency NEMA Class 1 Efficiency Levels Dry-Type Distribution Transformers Low Voltage (600V and below) Single-Phase Three-Phase Efficiency Efficiency V-T- Volume Commercial Distribution CA E June 014

3 Transformers.1 Features, Benefits and Functions 60 Hz operation (except as noted) Short-term overload capability as required by ANSI Meet NEMA ST-0 sound levels Meet federal energy efficiency requirements for low voltage dry-type distribution transformers effective as of January 1, 007 Standards and Certifications UL listed Industry Standards All Eaton dry-type distribution and control transformers are built and tested in accordance with applicable NEMA, ANSI and IEEE Standards. All 600 volt class transformers are UL listed unless otherwise noted. Seismically Qualified Eaton manufactured dry-type distribution transformers are seismically qualified and exceed requirements of the Uniform Building Code (UBC), International Building Code (IBC) and California Code Title 4. Volume Commercial Distribution CA E June V-T-3

4 .1 Transformers Accessories Please refer to Section.7 Page V-T-191. Technical Data and Specifications Frequency Eaton standard dry-type distribution transformers are designed for 60 Hz operation. Transformers required for other frequencies are available and must be specifically designed. Overload Capability Short-term overload is designed into transformers as required by ANSI. Dry-type distribution transformers will deliver 00% nameplate load for one-half hour, 150% load for one hour and 15% load for four hours without being damaged, provided that a constant 50% load precedes and follows the overload. See ANSI C for additional limitations. Continuous overload capacity is not deliberately designed into a transformer because the design objective is to be within the allowed winding temperature rise with nameplate loading. Insulation System and Temperature Rise Industry standards classify s and rise as shown below: Insulation System Classification Ambient + Winding Rise + Hot Spot = Temp. Class 40 C 55 C 10 C 105 C 40 C 80 C 30 C 150 C 5 C 135 C 0 C 180 C 40 C 115 C 30 C 185 C 40 C 150 C 30 C 0 C The design life of transformers having different insulation systems is the same the lower-temperature systems are designed for the same life as the higher-temperature systems. Enclosures Eaton s ventilated transformers, Types DS-3 and DT-3, use a NEMA rated (drip-proof) enclosure as standard, and are rated NEMA 3R with the addition of weathershields. Winding Terminations Primary and secondary windings are terminated in the wiring compartment. Encapsulated units have copper leads or stabs brought out for connections. Ventilated transformers have leads brought out to terminals that are pre-drilled to accept Cu/Al lugs. Aluminum-wound transformers have aluminum terminals; copper-wound models have copper terminals. Lugs are not supplied with these transformers. Eaton recommends external cables be rated 90 C (sized at 75 C ampacity) for encapsulated designs and 75 C for ventilated designs. Series-Multiple Windings Series-multiple windings consist of two similar coils in each winding that can be connected in series or parallel (multiple). Transformers with series-multiple windings are designated with an x or / between the voltage ratings, such as voltages of 10/40 or 40 x 480. If the series-multiple winding is designated by an x, the winding can be connected only for a series or parallel. With the / designation, a mid-point also becomes available in addition to the series or parallel connection. As an example, a 10 x 40 winding can be connected for either 10 (parallel) or 40 (series), but a 10/40 winding can be connected for 10 (parallel), or 40 (series), or 40 with a 10 mid-point. For additional information, please refer to Section.7 Page V-T-191. Sound Levels All Eaton 600 volt class general-purpose dry-type distribution transformers are designed to meet NEMA ST-0 sound levels listed here. These are the sound levels measured in a soundproof environment. Actual sound levels measured at an installation Average Sound Levels 1 NEMA ST-0 Average Sound Level in db will likely be higher (as much as 15 db greater) due to electrical connections and environmental conditions. Lower sound levels are available and should be specified when the transformer is going to be installed in an area where sound may be a concern. Up to 1. kv Above 1. kv Ventilated Encapsulated Ventilated Notes 1 Currently being reviewed and revised by NEMA. For other ratings or styles not shown, or for special enclosure types (including stainless steel), refer to Eaton. V-T-50 Volume Commercial Distribution CA E June 014

5 .6 Transformers Transformer Standards, Technical Data and Accessories Standards and Certifications Eaton dry-type distribution transformers are approved, listed, recognized or may comply with the following standards. Engineering Standards Catalog Product Name UL Standard 1 Notes 1 UL 5085 replaces UL 506. Applies to Applies to 5. 4 Applies to Applies to Applies to 3. 7 Applies to Applies to Applies to 30. UL/cUL File Number UL Listed Control Number cul Energy Efficiency File Number In addition to the above standards, Eaton dry-type distribution transformers are also manufactured in compliance with the applicable standards listed below. Not all of the following standards apply to every transformer. NEC: National Electrical Code NEMA ST-1: Specialty Transformers (C89.1) (control transformers). NEMA ST-0: General-Purpose NEMA TP-1: Guide for Determining Energy Efficiency for Distribution NEMA 50: Enclosures for Electrical Equipment (1000 volts maximum). IEEE C : General Requirements for Dry-Type Distribution and Power Transformers (including those with solidcast and/or resin-encapsulated windings). CSA File Number Insulation System Temp/ºC ANSI C : Terminal Markings and Connections for Distribution and Power ANSI C : Standard Test Code for Dry-Type Distribution and Power CSA C No. 47-M90: Air-Cooled Transformers (Dry-Type). CSA C9-M1981: Dry-Type CSA C. No. 66: Specialty CSA 80-94: Maximum Losses for Distribution, Power and Dry-Type NEMA TP-: Standard Test Method for Measuring the Energy Consumption of Distribution NEMA TP-3 Single- Phase Three- Phase Applicable IEC Standard Industrial Control Transformer MTE 5085 E X LR N/A MTK 5085 E X LR N/A Encapsulated Transformer AP 5085 E H N/A AP 1561 E H N/A EP 5085 E H LR N/A EP 1561 E H EV157 LR N/A / 76 5 EPT 5085 E H LR N/A / 76 7 EPT 1561 E H EV157 8 LR N/A MPC 106 E H LR Ventilated Transformer DS E H N/A 6076 DT E H 0 N/A KT 1561 E H 0 N/A N/A V-T-186 Volume Commercial Distribution CA E June 014

6 Transformers Transformer Standards, Technical Data and Accessories.6 Catalog Number Selection General-Purpose, Energy-Efficient, Mini Power Center, Shielded Isolation, Nonlinear, Buck-Boost, Marine Duty Transformers Example: S0N11S05A C Prefix Options = CSA labeled ventilated transformer Marine Duty QS = EPM marine (1-Ph encapsulated) LY = EPTM Marine (3-Ph encapsulated) RT = DS-3M marine (1-Ph ventilated) MV = DT-3M marine (3-Ph ventilated) Type S = EP (single-phase encapsulated) Y = EPT (three-phase encapsulated) T = DS-3 (single-phase ventilated) V = DT-3 (three-phase ventilated) P = Mini power center Z = Class 1 Division Groups A, B, C, D X = Harmonic mitigating (three-phase ventilated) Nonlinear H = KT-4 (three-phase ventilated) B = KT-9 (three-phase ventilated) N = KT-13 (three-phase ventilated) G = KT-0 (three-phase ventilated) J = KT-30 (three-phase ventilated) A = KT-40 (three-phase ventilated) K = KT-50 (three-phase ventilated) HT = KT-4 (single-phase ventilated) NT = KT-13 (single-phase ventilated) GT = KT-0 (single-phase ventilated) Notes 1 Model number is not used on newly designed/redesigned transformers. Copper windings. 3 Grade 304 stainless steel enclosure (does not imply a NEMA 4X rating). 4 Open type core and coil assembly. 5 Totally enclosed non-ventilated DS-3 or DT /60 Hz. 7 Low sound design. LS47 indicates low sound equal to 47 db; LS4 indicates 4 db. Primary Voltage 13 = 110 x 0 1 = = 10 x 40 9 = 08 7 = 00 5 = 0 3 = 30 4 = 40 0 = 40 x = = = = = = = = = = = = = Export model 54 = 10/08/40/77 Taps D = at +.5%, at.5% E = 1 at +5%, 1 at 5% F = 1 at 10% G = at 5% J = 4 at.5% K = 1 at 10% x at 5% L = at 5% x 4 at.5% M = at +.5%, 4 at.5% N = None R = 1 at +5%, at 5% P = 1 at +5%, at 5% x at +.5%, 4 at.5% T = 1 at +4.%, 1 at 4.% U = 1 at +.5%, 3 at.5% W = 1 at +3.5%, 1 at 3.5% X = at +3.1%, at 3.1% 8 Fungus proof. 9 Certified test report of standard production tests for the specific serial number to be shipped. j Certified sound level report. k CE Marked. l Thermal indicator embedded in center coil. Suffix TT indicates two thermal indicators of different temperature ratings, are installed. m NEMA TP-1 efficient. T S 0 N 11 S 05 A 81 = = = = = = = =1 16 =1.5 0 = T = 150 C rise with 0 C F = 115 C rise with 0 C B = 80 C rise with 0 C H = 130 C rise with 00 C G = 115 C rise with 00 C 04 = 1/4 06 = 16/3 08 = 4/48 14 = 110/0 1 = = 10 x = 10/40 54 = 17/54 19 = 190Y/110 8 = 08Y/10 9 = 08 5 = 0 delta 31 = 0Y/17 6 = 0 delta/110 midtap = 40 delta/10 midtap 64 = 40Y/139 4 = 40 delta 03 =3 05 =5 06 =6 07 = =9 10 =10 15 =15 1 =.5 5 =5 30 =30 Temperature Rise Secondary Voltage 37 = =45 50 =50 75 =75 99 =100 1 = = =167 =5 n 0 phase-shift (used with HMTs). o +15 phase-shift (used with HMTs). p 15 phase-shift (used with HMTs). q 30 phase-shift (used with HMTs). r CSL3 DOE 007 energy-efficient. s NEMA 4X Grade 304 stainless steel enclosure. t Easy install base. BK Grade 316 stainless steel enclosure (does not imply NEMA 4X rating). BL Integral -inch infrared viewing window. BM Integral 3-inch infrared viewing window. BN Integral 4-inch infrared viewing window. BO NEMA Premium Efficient. J = 80 C rise with 0 C P = 115 C rise with 130 C (encapsulated) S = 115 C rise with 180 C (encapsulated and MPC) L = 80 C rise with 180 C (encapsulated and MPC) 0 = 40 x = 40/480 7 = = 380 delta 37 = 380Y/0 34 = 400Y/31 51 = 416Y/40 35 = 440Y/54 6 = 460Y/66 47 = 480Y/77 48 = 480 delta 60 = 600 delta 61 = 600Y/346 4 = = 4160Y/ = = = = = = = = = = 1500 Suffix Options A...Y = 1 CU = SS = 3 ZZ = 4 NV = 5 X = 6 LS = 7 AF = 8 TR = 9 SR = j CE = k T = l EE = m NON = n POS = o NEG = p THR = q E3 = r SS4X = s Z = t S6 = BK I = BL I3 = BM I4 = BN N3 = BO For Eaton s industrial control transformers catalog number selection, see Page V-T-188. Contact your local Eaton sales office for voltage combinations not shown. Use table for catalog number breakdown only. Do not use to create catalog numbers because all combinations may not be valid. Volume Commercial Distribution CA E June V-T-187