Ackermann Catalogue. Systems that connect. Cable Management Systems for Floors and Walls

Transcription

1 Ackermann Catalogue Systems that connect Cable Management Systems for Floors and Walls

2 2 Introduction to Novar Novar plc is a UK quoted business with global sales of circa 1.5 billion. One of three divisions, Intelligent Building Systems supplies around 600m of products and services to the construction industry worldwide. Employing approximately 6,500 people, it is one of the largest businesses in its field, with operations in over 30 countries in North America, Europe, the Middle East, India, South East Asia and China. Novar s Intelligent Buildings Systems Division provides a wide range of high quality, leading offerings for electrical and data connectivity, high technology solutions for fire detection and alarm, access control, security, energy management and environmental controls to a diverse range of customers in both public and private sectors. BUILDING INFRASTRUCTURE WIRING DEVICES White, decorative, modular, surface, portable power, ingress protected, circuit protection, bell pushes and chimes. DATACOMS Structured cabling systems for data and voice communication, modular data, telecom and digital tv modules. CIRCUIT PROTECTION A range of pre, individual or factory assembled circuit protection products that set the standard in commercial, residential, and light industrial properties. CABLE MANAGEMENT Skirting and dado, perimeter and distribution, conduit and mini, alarm and communication, raised access floor, screeded floor, service poles and posts. BUILDING SYSTEMS SECURITY Intruder alarm panels, detection devices, internal and external sounders, conventional, digital CCTV and access control. FIRE DETECTION & EMERGENCY LIGHTING Domestic smoke detection, conventional control panels and ancillaries, analogue addressable panels and ancillaries, emergency exit signs and luminaries. COMMUNICATIONS Control modules, proximity readers, keypads, voice alarm, public address call systems. BUILDING MANAGEMENT AND ENERGY MONITORING Advanced building control systems for HVAC, lighting and environmental control.

3 Contents 3 The Ackermann company was founded in 1919 and has grown into an international organisation with subsidiaries in Dubai, France, Great Britain, Hong Kong, Poland, Singapore, Spain and Sweden and agents in over 30 countries around the world and is now a wholly owned business of Novar plc. Novar Ackermann GmbH + Co. KG is ISO 9001 certified and also received a TÜV certification for its environmental management system. The company designs and manufactures systems for the communication and cable management industries and specialises in the following: Telecommunication connectors and outlets. Connectors and components for Local Area Networks. Wall and underfloor cable trunking systems and accessories. Patient call systems for use in hospitals, clinics and homes for the elderly. This catalogue summarises the main products for our cable management systems. Due to the large number of products within the overall portfolio, it is not possible to include all items within our present manufacturing range. Hence, readers are asked to contact us or our appointed overseas agents in the event that further information is required. Separate catalogues are available on request: For markets using British and French standards. In Spanish and French. For product ranges and systems referred to above. Floor Systems F N 30-EÜK 35-OKA 53-HB 54-DB 55-AIK 56-TE LI Tank 57-GES Hanging Service Modules 63-VH Service Poles and Posts 66-ISS Wall Trunking Services 70-WIK Installation Devices 78-Installation Devices 80-83

4 4 Screed System CATALOGUE GROUP 30-EÜK Underfloor electrical installation duct for screed-covered installation a Underfloor installation duct, 3 compartment c b Coupler c Vertical bend e d b a b f h i j g d Underfloor box, empty (for installation of a service outlet box) e Stacking frame f Service outlet box, (flush with floor service units see Cat.-Gr. 57 GES) g T8NL te li tank (pedestal service outlet units, see Cat.-Gr. 56 te li tank) h Rough concrete i Screed a b j Floor covering a b For electrical installation in the floor, the Underfloor installation ducting system is laid on the construction concrete before the final floor screed is applied. A very high degree of connection flexibility from: Subsequent drilling of duct (fitting of a US 80 duct outlet, see page 13). Changing service box mounting plates (adding pedestal or flush floor service outlets, see Cat.-Gr. 56 and 57). Trunking in other widths and heights and other accessories available on request. Important instructions which must be considered before laying the carpet! Before laying the carpet, you need to decide what function the Underfloor box should perform, junction box (see Fig.1) or service box (see Fig.2), as this decision affects which end cover has to be fitted instead of the protective cover. This will determine where the floor covering is cut. Junction Box (Fig.1) For the junction box with SRU carpet protector frame, the entire area of the installation cover A is cut out of the carpet. A Insert of the final cover The final cover should only be fitted after the screed has hardened and the protection cover has been removed. Service Box (Fig.2) For the service box, only the area of the cover blanking plate B needs to be cut out of the carpet. When using the junction box insert ZES, the cutout corresponds to that for the service box (GES). Cutting the floor covering correctly Depending on the purpose: B only along the service outlet mounting plate aperture or A along the outside edge of the mounting plate. B B A Apparatus installation outlet closed by coverblind plate

5 Screed System 5 CATALOGUE GROUP 30-EÜK Cassette solutions for junction boxes and service boxes in floors with hard floorings The Cassette solutions are designed for use in dry rooms. The range includes cassettes with a center tube cord outlet for floors which are mopped and versions with a edge cord outlet for dry cleaned 1. 3 mm floors, plus blanking cassettes. They fulfil all the requirements of DIN VDE with respect to moisture protection and load-bearing capability. The narrow cassette frame fits flush with the floor covering after it is laid. The cables are protected and tread-proof, either by means of the edge cord outlet (for dry cleaned floors) or by means of a center tube cord outlet (for mopped floors). Cassettes of different heights are Mounting the cassette solutions on UZD underfloor junction box available to suit different flooring thicknesses. Cassette structure on UZD Adjusting the flooring thickness on the cassette frame and in the cassette Cassette frame Cassette E 75 H Underfloor box UZD.. Cassette recess = H-2 mm Tube cord outlet Cassette solutions number of mounting boxes which can be fitted For the RKS cassette with edge cord outlet, up to three mounting boxes (GB2, GB3) can be fitted into the UZD and This means the screed height must be at last 75 mm. For the cassette with the RKF center tube cord outlet, the number of mounting boxes also depends on the available height from the top Dimensions in mm edge of the raw floor to the top edge of the screed (see diagram opposite). The middle mounting box can only be used if E 130 mm. If there is sufficient installation depth, a ladder Cassette frame Cassette extension (Part No A must always be used for the middle mounting box. H Cassette recess = H-2 mm Tube cord outlet A WAEG-U or WAEG6C-U RJ45 connection unit can be fitted instead of a mounting box. E 120 Part No A Underfloor box UZD.. Rough concrete Dimensions in mm

6 6 Screed System CATALOGUE GROUP 30-EÜK EÜK duct and accessories, underfloor junction and branch box Description Underfloor box with external height adjustment to any height from 70 to 120 mm (UZD or UGD), opening side walls, pre-punched in accordance with the duct size. The box can be raised by 35 mm by stacking frames. Material Underfloor box body, side walls and installation protection cover made of pre-galvanised sheet steel. Levelling frame made of diecast aluminium. Delivery condition Underfloor box adjusted to a screed height of 70 mm. ACKERMANN - EÜK - VDE - ÖVE - KEMA - KE Underfloor installation duct S 2/3 compartments Standard length supplied = 2 m Material: sheet steel, pre-galvanised In accordance with DIN 18560, the minimum screed covering for cement screed is 35 mm. VME: 2 m Coupler VL For use as coupler or expansion joint. (25.5) h= 28 mm h= 38 mm (35.5) (25.5) h= 28 mm h= 38 mm (35.5) h= 28 mm h= 38 mm Notes Earth continuity For the earth continuity, a earth conductor clamp (8 AWR) connection bracket is required for the underfloor box. Underfloor junction and branch box Duct end cap SE To close duct ends. h= 27 mm h= 37 mm The inside of the box is sealed against on-site contamination by an installation protection cover. This installation protection cover must be replaced with a assembly cover prior to laying the floor covering. Nominal compartment widths in brackets 2 Compartment 200mm 200mm Vertical bend KV To change the direction of the duct 200 mm each. (25.5) h= 28 mm h= 38 mm (35.5) (25.5) h= 28 mm h= 38 mm (35.5) 2 Compartment 3 Compartment Underfloor junction and branch box UZD As described opposite, for ducts with nominal heights of mm. Important! Before laying the flooring, read notes on page 4 Dimensions: b = box body B = base plate 3 Compartment Stacking frame ARU To increase height of underfloor boxes by 35 mm each. Material: die-cast aluminium (4 or 8 thread stacking pins also supplied). VDE- ÖVE- KEMA- - EÜK- VDE- ÖVE- KEMA- KEUR- Earth conductor clamp 8 AWR For use in underfloor junction and branch boxes UZD and underfloor empty box UGD -. Material: sheet steel, galvanised, yellow passivated. Terminal range: 2 x mm. ACKERMANN - EÜK- VDE- ÖVE- A- KEUR - ACKERMANN Supplied in packs of 10.

7 Screed System 7 CATALOGUE GROUP 30-EÜK Duct width 190 mm Part no. Code Duct width 190 mm Part no. Code Duct width 190 mm Part no. Code 2 Comp B2 S2/ D2 S2/ Comp B2 S2/ D2 S2/ Comp B3 S3/ D3 S3/ Comp B3 S3/ D3 S3/ B VL D VL B VL D VL B VL D VL B SES D SES B SES D SES B SES D SES Comp B2 KV2/ D2 KV2/ Comp B2 KV2/ D2 KV2/ Comp B3 KV3/ D3 KV3/ Comp B3 KV3/ D3 KV3/35038 for ducts of 190 mm for ducts of mm for ducts of mm b = 270 mm B = 330 mm A UZD190 b = 330 mm B = 390 mm A UZD250-2 b = 430 mm B = 490 mm A UZD350-2 C = 250 mm A ARU190/35 C = 330 mm B ARU250/35-2 C = 430 mm C ARU350/35-2A CV 8AWR CV 8AWR CV 8AWR For ducts in other widths and heights and other accessories, see catalogue Screed-based electrical installation systems with installation equipment.

8 8 Screed System CATALOGUE GROUP 30-EÜK Accessories for use of the underfloor junction and branch box UZD as an underfloor service box UGD UGD = UZD + DUG Once the te li floor duct system has been laid and the screed has set, the installation protection cover of the underfloor junction and branch box is replaced with an appropriate mounting cover for Mounting cover^ DUG.2 For fitting a service outlet GES 2*. Material: 4 mm steel, pre-galvanised. fitting the service outlet box. The minimum screed height required is 70 mm. If the underfloor box is not used immediately, the flooring is glued over it. The flooring is later cut away to reveal the D D Blanking plate cover DUG-B. To fit. Material: 3 mm steel, pre-galvanised. blank cover plate and fit in the service outlet box (Cat. Gr. 57 GES) (see also instructions Cat. Gr. 30 EÜK). Note on assembly Mounting cover^ DUG.RM2 For fitting a service outlet GESRM 2*. Material: 4 mm steel, pre-galvanised. Before laying the carpet, the DUG assembly cover must be fitted. See note on page 4 for carpet cutting information. Danger! Installation openings in the floor must be covered so they are safe to walk on. See DIN VDE 0634 Part 2, Paragraph and the job site regulations. Mounting cover^ DUG.4- For fitting a service outlet GES 4* or a junction box ZES 4. Material: 4 mm steel, pre-galvanised. D D Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised. Mounting cover^ DUG.R4 For fitting a service outlet GESR 4* or a junction box ZESR 4. Material: 4 mm steel, pre-galvanised. D D Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised. Mounting cover^ DUG.6 For fitting a service outlet GES 6* or a junction box ZES 6. Material: 4 mm steel, pre-galvanised. D D Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised. Options for use as service box Mounting cover^ DUG.R7 For fitting a service outlet GESR 7* or a junction box ZESR 7. Material: 4 mm steel, pre-galvanised. D D Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised. Mounting cover^ DUG.9 For fitting a service outlet GES 9* or a junction box ZES 9. Material: 4 mm steel, pre-galvanised. D D Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised. D D Mounting cover^ DUG.R9 For fitting a service outlet GESR 9* or a junction box ZESR 9. Material: 4 mm steel, pre-galvanised. Blanking cover plate DUG-B. To fit. Material: 3 mm steel, pre-galvanised.

9 Screed System 9 CATALOGUE GROUP 30-EÜK Nominal size 190 for UZD 190 Part no. Code Nominal size 250 for UZD Part no. Code Nominal size 350 for UZD Part no. Code DUG290/ GES DUG-B A DUG190RM DUG190/GES4-1 D = 243 mm B DUG250-2GES4 D = 282 mm B DUG350-2GES4 D = 383 mm DUG-B DUG-B DUG-B DUG190GESR4-1 D = 243 mm C DUG250-2GESR4 D = 282 mm C DUG350-2GESR4 D = 383 mm DUG-B/R DUG-B/R DUG-B/R D DUG-250-2GES6 D = 282 mm D DUG-350-2GES6 D = 383 mm DUG-B DUG-B H DUG350-2GESR7 D = 383 mm D DUG-B/R E DUG350-2GES9 D = 383 mm A DUG-B G DUG350-2R9 D = 383 mm ^ 4 fixing screws included * Service outlets, see group 57-GES C DUG-B/R9

10 10 Screed System CATALOGUE GROUP 30-EÜK Accessories for dry areas with wet mopped floors Moisture protection as set out in DIN VDE Blanking cover DUF Including RD rubber seal and V2A cover fixing screws for flush, moisture-protected sealing of underfloor boxes. Material: 4 mm steel, pre-galvanised. 4 fixing screws included. Flooring insert cassette BEK/F Including rubber seal. For moistureprotected final sealing of underfloor junction and branch boxes. Material: V2A, 1 mm thick. Height H = 3 mm H = 4 mm H = 5 mm L Other cassette heights available on request. Cassette solutions Load tested and moisture protection in accordance with DIN VDE Material: V2A. Device installation under RKF and RKS in installation kit (MS2 GB2, MSRK). H L Cassette frame RK For junction boxes, with cassette for wood, ceramic and stone floorings, for smooth floorings only. Height H = 10 mm H = 15 mm H = 20 mm H = 25 mm H = 30 mm On request: Brass cassettes Cassettes with threaded sleeve Note: Floorings with a rough surface require additional equipment in the cassettes, e.g. threaded sleeves (on request). For round cassettes, see page 45. H L Cassette frame RKF With central tube cord outlet for the installation of installation devices in wet-mopped floorings. Height H = 10 mm H = 15 mm H = 20 mm H = 25 mm H = 30 mm Accessories for dry areas with floors cleaned using dry methods H L Cassette frame RKS With edge cord outlet for the fitting of installation devices in dry-cleaned floorings. Height H = 15 mm H = 20 mm H = 25 mm H = 30 mm Installation kit for device installations under cassettes Installation kit MS2GB2 For fitting of 4 individual installation devices in the underfloor junction and branch boxes. With 2 mounting boxes GB 2 and all the parts required for fitting. Note: no device installation possible to a height of 115 mm under RKF cassette (top edge of raw floor to top edge of finished floor E). Installation kit MSRK For fitting of 9 individual installation devices in the underfloor junction and branch box. With 3 mounting boxes GB 3 and all the parts required for fitting. Note: minimum fitting height 75 mm. Note for installation kit MS2GB2 and MSRK. E = installation height required. Cassette version UZD 190 US 250-2/ RKS 85 mm 90 mm - RKF 115 mm 130 mm* Ladder extension GES/RV 2-part component that can be slotted onto the MSRK installation kit. Note: Component is required if the middle mounting box is to be used under cassette RKF. Supplied in packs of 2. * The middle mounting box cannot be used for installation heights of between 85 and 130 mm.

11 Screed System 11 CATALOGUE GROUP 30-EÜK Nominal size 190 for UZD 190 Part no. Code Nominal size 250 for UZD Part no. Code Nominal size 350 for UZD Part no. Code A DUF190/120 D = 244 mm A DUF250-2 D = 283 mm B DUF350-2 D = 383 mm A BEK/F250-2/ C BEK/F250-2/ D BEK/F250-2/5 L = 282 mm B BEK/F350-2/ C BEK/F350-2/ D BEK/F350-2/5 L = 383 mm A RK/V1/ B RK/V1/ C RK/V1/ D RK/V1/ E RK/V1/30 L = 244 mm A RK2V2/ B RK2V2/ C RK2V2/ D RK2V2/ E RK2V2/30 L = 282 mm A RK/V3/ B RK/V3/ C RK/V3/ D RK/V3/ E RK/V3/30 L = 383 mm A* RKF2V1/10* B* RKF2V1/15* C* RKF2V1/20* D* RKF2V1/25* E* RKF2V1/30* L = 244 mm A* RKF2V2/10* B* RKF2V2/15* C* RKF2V2/20* D* RKF2V2/25* E* RKF2V2/30* L = 282 mm A* RKF2V3/10* B* RKF2V3/15* C* RKF2V3/20* D* RKF2V3/25* E* RKF2V3/30* L = 383 mm B* RKS/V1/15* C* RKS/V1/20* D* RKS/V1/25* E* RKS/V1/30* L = 244 mm B* RKS2V2/15* C* RKS2V2/20* D* RKS2V2/25* E* RKS2V2/30* L = 282 mm B* RKS/V3/15* C* RKS/V3/20* D* RKS/V3/25* E* RKS/V3/30* L = 383 mm A MS2GB A MS2GB A MS2GB2 * Add the code for the colour required. The code with the RAL colour code E MSRK/2/3GB F MSRK3/3GB3 The part no. number with the code letter Colour RAL colour Code code letter Iron-grey 7011 A A1 GES/RV A1 GES/RV A1 GES/RV Grey-beige 1019 E Graphite 9011 F

12 12 Screed System CATALOGUE GROUP 30-EÜK Underfloor Service Box UGD ACKERMANN - EÜK- VDE- ÖVE- - EÜK- VDE- ÖVE- KEMA- KEUR- Part no. Code e Underfloor box empty UGD 190 For direct installation of a flush floor service unit GES installation unit or a ZES junction box insert. for GES 2 or ZES 2 for GES 4 or ZES 4 for GESR 4 or ZESR A UGD190/ B UGD190/ C UGD190R4 e Underfloor box empty UGD For direct installation of a flush floor service unit GES installation unit or a ZES junction box insert. for GES 4 or ZES 4 for GESR 4 or ZESR 4 for GES 6 or ZES A UGD250-2/ B UGD250-2R C UGD250-2/6 e Underfloor box empty UGD For direct installation of a GRAF9 or a flush floor service unit GES installation unit or a ZES junction box insert. for GES 4 or ZES 4 for GESR 4 or ZESR 4 for GES 6 or ZES 6 for GESR 7 or ZESR 7 for GES 9 or ZES 9 for GRAF9, GESR 9 or ZESR B UGD350-2/ C UGD350-2R D UGD350-2/ H UGD350-2R E UGD350-2/ G UGD350-2R9

13 Screed System 13 CATALOGUE GROUP 30-EÜK Floor box single outlet US 80 Fitting tools such as cover remover, pliers, fitting keys, drill bits or templates, see also Cat. Gr. W fitting tools. Part no. Code Underfloor outlet box UDL For conduit installation 2 x 2 Pg 16. Material: pre-galvanised metal sheet box sealed with assembly protection cover A UDL1-80/R16 UDL 1-80 For fitting of an pedestal service outlet unit which projects above the floor (te li tank) or a SH or SHF height-adjustable installation unit. For screed heights of 60 to 75 mm. Note: Assembly protection cover to be replaced after screed work. Single duct US 80 Suitable for fitting of an installation device in dry areas or fitting a te li tank (see Cat. Gr. 56 te li tank) for subsequent drilling of channels. Screed heights above the duct: mm. Material: die-cast zinc. Installation devices for fitting in US 80, see Cat. Gr. 78 Installation and connection device for electrical installation systems A US80/32 Adjustment ring AR To increase the height of the underfloor outlet box UDL 1-80/R16 and the duct outlet US 80 by 24 mm. Material: die-cast zinc AR80/24 Blanking plate DBS Can be used as assembly protection cover for duct outlet US 80. Material: 2 mm sheet steel, pre-galvanised DBS80 Blank cover BAB Can be screwed into US 80 Material: polyamide, matt surface. External dimension: ø100 mm. Colour: iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL A BAB80/ E BAB80/ F BAB80/9011

14 14 Screed System CATALOGUE GROUP 30-EÜK - EÜK Screed-covered duct system Notes on using screed-covered duct systems in screed Screed work Screed As the duct system or part of the duct system serves as a binding pull gauge for the screed, the levelling must be agreed with the construction company. When applying the screed, the person laying the screed must carefully prepare, seal and pull away the screed around the junction boxes. Divider strips must not be used as the junction boxes can only achieve the robustness specified if they are joined directly to the screed. Using divider strips can damage the flooring. Duct UZD / UGD Concrete Insulation layer (cover) Insulation Important: Screed can be damaged by cracks. Do not put strain on adjacent systems and system components that are joined to the screed before the screed has hardened. Screeds, general. Under some circumstances, chemical or thermal strain can occur which means taking special additional measures to protect the installed systems (see e.g. VOB Part C (ATV), DIN 18353, Paragraph 3.1.8). Use in poured screeds When using screed-covered duct system in poured screeds, all the openings in the duct system must be sealed using appropriate means (e.g. using adhesive tape). Care should be taken to ensure that the sealing process does not create hollow areas between the components and the screed. Possible openings can be found, for example, at joints between ducts and connection lugs and vertical bends or to underfloor boxes UZD/UGD. The top connections, like the assembly protection cover and the assembly or blanking covers should be sealed using appropriate means. Aggressive screed (e.g. magnesia screed) With this screed, all metallic components which come into contact with the screed should be protected with an accredited corrosion protection agent based on epoxy resin (two coats). See also VOB Part C (ATV) DIN paragraph Use in poured asphalt Essentially, there are no restrictions with respect to the use of the installation duct system in poured asphalt. The following is deemed as the most practical approach to using the system in poured asphalt: a) Under no circumstances must the screedcovered ducts come into direct contact with the poured asphalt. The high installation temperature (approx. 250ºC) means that it is not impossible for metallic components to be deformed. b) The duct systems are laid on the raw floor and fixed in accordance with the fitting instructions. c) The duct routes are protected against heat shock using an appropriate layer of insulation (e.g. Fasoperl sheets or bitumen-coated corrugated cardboard). d) The box bodies do not require additional insulating strips. e) The poured asphalt is applied.

15 MANN-EÜK-VDE-ÖVE-KEMA-KEUR- ACKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR- SD-3500 IMPEX ACKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR-ACKERMANN-EÜK-VDE-ÖVE-KEMA CKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR-ACKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR- ACKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR-ACKERMANN-EÜK-VDE-ÖVE-KEMA-KEUR- ACKERMANN-EÜK-VDE- ACKERMANN-EÜK-VD Screed System 15 CATALOGUE GROUP 30-EÜK 30 EÜK screed-covered underfloor electrical installation duct System installation instructions 1. Using the duct layout plan to select a fixed starting point for the installation, for example a junction box. 2. Tie two guide lines (approx 150mm above the raw concrete) at 90º to each other, ensuring that they match the duct layout plan. 3. Position the first junction box centrally below the intersection of the guide lines and level to required screed depth. (boxes supplied adjusted to 70mm). ACKERMANN-EÜK-VDE- ÖVE- KEMA-KEUR-A - EÜK- VDE- ÖVE- KEMA- KEUR-ACKERMA ACKERMANN-EÜK-VDE- ACKERMANN-EÜK-VD ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - ACKERMANN - EÜK- VDE-ÖVE A- KEUR - ACKERMANN-EÜK-VDE-ÖV 4. Lay duct / trunking sections to reflect the layout plan. Ensure ducting compartments are aligned as indicated by the continuous marking on the top of the duct. 5. Open the pre-punched side walls of the underfloor box and insert the duct as far as it will go. 6. Fasten the underfloor / junction box and re-adjust to required screed depth level. ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR -ACKERMANN - EÜ 7. Fasten the duct sections at coupling devices to the concrete. 8. Important: Ensure external duct partition markings are aligned. 9. Attach an earth continuity connector at all duct couplings or joints. 3 CKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - A ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - ACKERMANN - E ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - A ACKERMANN - EÜK - VDE - ÖVE - KEMA - KEUR - ACKERMANN The minimum screed depth is 70mm. Boxes can be adjusted to the required depth (max 120mm) using the leveling screws. 11. By means of stacking frame the height of the floorbox can be extended by +35 mm. Stacking frame has to be mounted on top of the floor box. 12. Underfloor outlet - US 80 - can be levelled to top screed level with help of adjustment rings (15mm or 24mm). Mounting sequence: unscrew balancing ring (1) + (2), add adjustment ring to balancing ring, screw levelled balancing ring into outlet (3).

16 16 Screed System CATALOGUE GROUP 35-OKA Flush floor trunking system OKA2 The desire to open the whole length and width of trunking is a practical requirement that makes laying cables easier and allows better use of the inside of the trunking. The number of cables laid can be changed rapidly and new connection requirements accommodated. The Open trunking for connection technology incorporates i b j n k covers to fit and extend flush floor service units and pedestal service units. Varying these device connections and usage covers can produce connection patterns that are oriented towards the requirements. The flush floor trunking system OKA 2 is supplied as a ready-to-fit f c a l m package. h The use of extension units means the trunking is left free for cables. d g e Flush floor trunking for dry-swept and wet mopped floors OKU f see Catalogue Key to diagrams h Trunking connection bracket a OKA-2 underfloor trunking unit i Trunking partition N N -22,5 b c Base tray Cover plate for installation of a GES service outlet j k Cover plate support profile te li tank T8NL (pedestal installation unit Cat. Gr. 56 te li tank) d End cap l Concrete N -60 N -31 N +150 e Fixing bracket m Screed f Screed anchor n Flooring g Aluminium side profile Accessories

17 Screed System 17 CATALOGUE GROUP 35-OKA Part no. Code OKA-2 trunking and accessories Trunking unit OKA 2 D With 3 blanking covers, one-compartment. Nominal size Levelling range mm mm mm mm mm mm mm mm Trunking unit OKA 2 DG With 3 covers with installation opening for flush floor service unit. Nom. size GES Lev. range mm mm mm mm mm mm mm End cap OKA 2 ES Fits OKA 2 D trunking units. Nominal size Levelling range mm mm mm mm mm mm mm mm Trunking Partition OKA2 / TW For optional internal separation of the OKA-2 Length supplied: 2400 mm. For trunking heights: 30 mm 40 mm 50 mm Extension unit OKA 2A To enable lateral flange connection to an OKA 2 trunking unit for fitting a flush floor service unit GES 4, 6 or 9, including end cap and trunking connection brackets. Fitting opening sealed with 3 mm cover blanking plate. With 3 mm floor guide profile. Levelling range: 30 mm Height: 60 mm Length: 460 mm Width: 400 mm GES 4 GES 6 GES AR OKA2/20030D BR OKA2/20040D BR OKA2/25040D CR OKA2/25060D BR OKA2/30040D CR OKA2/30060D CR OKA2/35060D CR OKA2/40060D CR OKA3/30060DG CR OKA3/35060DG CR OKA3/35060DG CR OKA3/35060DG CR OKA3/40060DG CR OKA3/40060DG CR OKA3/40060DG AR OKA2/20030ES BR OKA2/20040ES BR OKA2/25040ES CR OKA2/25060ES BR OKA2/30040ES CR OKA2/30060ES CR OKA2/35060ES CR OKA2/40060ES C OKA2TW D OKA2TW F OKA2TW AR OKA2A60DG4/ AR OKA2A60DG6/ AR OKA2A60DG9/3 Application Installation trunking that can be opened across its entire length and width to carry cables, for mounting pedestals or flush floor service units. Sidewalls can be adjusted to the screed height using levelling screws. Connection to screed using screed anchors (which can be fitted into the external groove on the side profile). Flooring guide profiles: Flush or 3 mm raised in the side profile (raised to protect the cut edge of the flooring). 4.5 mm raised on request. Use with flush floor service units Flush floor service units are fitted either along the course of the trunking or in additional units with flange connections on the side. (extension unit) Blanking covers can be replaced with assembly covers. A height of at least 70 mm is required to fit the device inserts. Ready-to-fit trunking unit consisting of: Trunking base tray (with side and floor guide profiles). 6 fixing brackets. 6 screed anchors. 3 cover plate joints or cover plates supports (for nominal sizes 350 and 400). 3 blanking covers or 3 covers with assembly opening for GES device insert. Material Trunking base made of 1 mm sheet steel, pre-galvanised: side and floor guide profiles aluminium. Blanking covers made of 4 mm steel, pre-galvanised. Length supplied: Bottom section of trunking: 2400 mm. Cover: 800 mm. Design OKA 2 trunking are available: In widths 200, 250, 300, 350 and 400 mm. In heights and levelling ranges mm mm mm mm. Earth conductor clamp 8 AWR For use in the side profiles and base tray of the trunking unit. Material: sheet steel, galvanised, yellow passivated. Terminal range: 2 x mm 2 Supplied in packs of CV 8AWR Earth continuity For earth continuity earth conductor clamps are required for the trunking unit order 8AWR separately for bottom section of trunking and side profiles. Partition pieces are automatically connected so earth continuity is given. Trunking units and extension units available for other flush floor service units and levelling heights on request.

18 Screed System CATALOGUE GROUP 35-OKA Part no. Code OKA 2 accessories Trunking connection angle OKU/VW For connecting trunking side profiles on T and cross branches. Material: steel, galvanised. Supplied in packs of C OKU/VW Trunking connection angle OKA 2VW For 90º bracket branch produced on-site Material: steel, galvanised D OKA2VW Cover plate support OKA/DT3 To support trunking lid at right angle intersections. ( T and 4 way junctions). Material: aluminium profile, extruded, cover support areas have self-adhesive rubber strips K OKA/DT200/4H J OKA/DT250/4H D OKA/DT300/4H E OKA/DT350/4H F OKA/DT400/4H3 Insert nuts T/EM For fixing te li tanks to cover plates. Supplied in packs of T/EM Individual OKA 2 parts Cover joint seal OKA 2 DSD For supporting and sealing cover joints. Material: sheet steel, galvanised with hard rubber seal glued on A OKA2DSD B OKA2DSD C OKA2DSD300 Cover joint seal OKA 2 DSU As above (OKA 2 DSD), but with adjustable central support. OKA2DSU A B Fixing bracket OKU/NEV 110 For fixing, connecting and levelling of trunking sections. Adjustment to height of screed to be done on site. Levelling max 110 mm. Supplied in packs of AV OKU.NEV110

19 Screed System 19 CATALOGUE GROUP 35-OKA OKA 2 Flush floor trunking system Notes on using flush floor trunking systems Screed work As the trunking system will form part of the finished floor it is Screed important to ensure that the entire system is levelled to the correct height, agreed within the construction company. Trunking Cover Screed anchor When applying the screed it must be ensured that the concrete is forced into and around the side profile leaving no air gaps. Protective strips must not be applied to the trunking, preventing air Aluminium side profile Separation layer (cover) gaps, as the trunking systems can only achieve the strength and robustness specified if they are joined directly to the screed. Using protective strips can damage the flooring and reduce its robustness. Base section of Trunking Concrete Fixing Bracket Important: Screed can be damaged by cracks. Do not put strain on adjacent systems and system components that are joined to the screed before the screed has hardened. Screeds, general. Under some circumstances, chemical or thermal strain can occur which means taking special additional measures to protect the installed systems (see e.g. VOB Part C (ATV), DIN 18353, Paragraph 3.1.8). Use in poured screeds When using flush floor trunking systems in poured screed, all the openings in the duct system must be sealed using appropriate means (e.g. using adhesive tape). Care should be taken to ensure that the sealing process does not create hollow areas between the components and the screed. Possible openings can be found, for example, at joints between trunking units, at branches, additional units and end caps, and where the bottom section of the trunking meets the side profile. The tops of the channels side profiles and cover joints - should also be sealed using appropriate means. Aggressive screed (e.g. magnesia screed) With this screed, all metallic components that come into contact with the screed should be protected with an accredited corrosion protection agent based on epoxy resin (two coats). See also VOB Part C (ATV) DIN paragraph Use in poured asphalt Essentially, there are no restrictions with respect to the use of the installation trunking system in poured asphalt. The following is deemed as the most practical approach to using the system in poured asphalt: a) Under no circumstances must the trunking system come into direct contact with the poured asphalt (with the exception of the screed anchors). The high installation temperature (approx. 250ºC) means that it is not impossible for metallic components to be deformed. b) The trunking system is laid on the raw floor and fixed in accordance with the fitting instructions (fit the screed anchors at the points shown). c) An insulating strip of approx. 15 to 20 mm is applied to both sides of the trunking. d) The poured asphalt is applied. Once it has cooled, the insulating strip between the duct and the screed plate is removed and the gap is filled with an appropriate sealant (e.g. cold bitumen) so the surface is flush.

20 SD-3500 IMPEX 20 Screed System CATALOGUE GROUP 35-OKA 35 OKA 2, open underfloor electrical installation duct System-specific fitting instructions Guide Line 1. Using the trunking / duct layout plan select a fixed starting point of the installation. Mark the position of the (branch units / junction boxes) on the slab (raw concrete). 2. Lay out the prefabricated parts reflecting the assembly plan. 3. Align the trunking bases. 1. Guide line Fasten fixing brackets (6 pes. to each trunking base) to couple trunking sections and adjust trunking roughly flush with floor level (screed level). Mounting distance of fixing angles is 80Omm. 5. Fasten fixing brackets to slab. 6. Branches to be built at site. Trunking base and side profile has to be cut out to width of branching unit. Use cover plate support profile for trunking covers. Trunking and branch unit are fixed with connecting brackets in the side profiles. When In-screed underfloor trunking EÜK is used for branching, only the trunking base has to be opened. N-11mm 11mm 7. 90º angle unit requires an end cap OKA..ES. One side profile is shortened by trunking width (N - 11 mm), opposite side profile is shortened by 11 mm acc. to figure above. End cap is fixed to trunking base. Trunking and angle unit are fixed with brackets in the side profiles. 8. Cross-over junctions should be carried out as described under fig. 6. Use cover plate supports on both sides. angle units are fixed with brackets in the side profiles of the trunking. 9. Adjust entire trunking system flush to the required screed depth. Fasten fixing angles on raw concrete. Remove handling aids. Attention: Trunking must not be applied to any load from now on! Don't walk over the trunking during further installation steps!

21 OKA OKU OKA OKU Screed System 21 CATALOGUE GROUP 35-OKA Apply screed anchors to side profiles by using separate mounting instruction on packaging. 6 screed anchors fix to each trunking section. 11. Cut levelling screws of fixing brackets to 5mm lower than top of side profile. (Use a tape to cover the top sides of side profiles to prevent ingress of screed into fixing holes.) 12. After installation of OKA 2 trunking the screed work should start. Attention: - Don't walk over the trunking during screed work! Trunking can be used to even/smooth the screed. Side profiles must be fully supported by screed. 13. Earthing of trunking: All metallic parts of the trunking (base and side profiles) provide location for the earth conductor clamp 8AWR (separate order no.). 14. Trunking units with nominal size >350 cover joint supports are used instead of cover joints. Adjust cover joint supports to correct height. Adjust the adjustment screw to appropriate height. For uneven slabs, open trunking base so that the support stands on the raw concrete. 15. To ease electrical installation, the trunking covers, cover joints and cover joint supports can be removed. Attention: If cover joint supports are removed, the correct position and height adjustment of the support screw has to be checked carefully when trunking is closed. delivery status, flush floor covering Offset 16. Supplied as standard with the floor guide profile flush with the side profile. 17. When floor covering is laid, the floor guide profile has to be taken out, turned by 180º and laid back into the side profile. Offset height is either 3 or 4.5mm.

22 22 Hollow floors CATALOGUE GROUP 53-HB System components for hollow floors One way of supplying the work station with connections to power and information technology networks in administrative buildings is by using hollow floors. This floor replaces conventional screed and is a raised floor with a jointless support plate made of poured screed. Hollow floor with moulding plates mm mm mm mm Holes can be made in the support layer to fit flush floor service units either: 4 When pouring the floor by using appropriate boarding. By subsequent drilling using a diamond bit (dry drilling process). This means connection requirements can be accommodated anywhere and at any time. Hollow floor with film boarding mm mm mm mm Key to diagrams 1 Flooring 2 Poured screed 3 Film or plaster moulding plate 4 Concrete The installations are made in the hollow floor from the distribution systems for each floor, which are normally at the heart of the building. Supply zones in the hollow floor either have a considerable number of inspections opening in rows or, and this is the preferred option, have a feed trunking which is open throughout. The cables are gathered into bundles and then led individually to the relevant workplaces. Any underfloor subdistribution systems required should then be placed in these zones Fixing of a flush floor service unit into a hollow floor using a split clip. Part no. Code Note: other boarding dimensions available on request Boarding 7 SK/HB To produce a chamber to fit flush floor service units into hollow floors. Note: Once the screed has hardened, the part sticking out should be cut off with a carpet knife. d = 215 mm, H = 50 mm d = 275 mm, H = 55 mm d = 305 mm, H = 55 mm For flush floor service units, see page 33 and following A 7SK/HB C 7SK/HB B 7SK/HB305

23 Raised floor 23 CATALOGUE GROUP 54-DB System components for raised floors Raised floors generally consist of individual raised floor tiles (f) which are easy to re-configure or replace. This means the workstation connections can be arranged variably. Installation systems like the ACPS system, or the conventional installation system a combination of underfloor distribution, flush floor service units and pre-wired mounting boxes make providing electricity to large raised floor surfaces easier. Both system solutions ACPS and conventional c f a d offer great flexibility to future changes to workplace requirement. Underfloor distribution systems and ACPS system components are laid in e b a grid of 7 to 10 m and supply a corresponding number of work stations with all the necessary connections (power, data, and Key to diagram a) Underfloor distributor UVS for power telephone). When work stations are being regrouped, the flexible connecting b) Underfloor distributor UVF for telecommunication c) Underfloor distributor UVD WAEG-U for data d) GES 8/10 DB flush floor service unit cables between underfloor distribution systems or ACPS and floor boxes or cable outlets enable the raised floor connection tile, e) GES 6 DB flush floor service unit including the floor box, to be moved f) Raised floor tiles to its new work station within a limited area. This means it is not necessary to disconnect an existing electrical connection. All that is required is to pick up the relevant Detailed diagram of fitting flush floor service unit into raised floor row of floor plates and re-configure it. This can be done without the assistance of skilled electricians. Even more major installation changes, during which electrical connections need to be disconnected, can be done without skilled electricians. The pluggable connections mean that all the necessary workplace connections are quickly ready for use. For flush floor service units, see Page 33 and following. For pre-wires mounting boxes, see Page 42. For underfloor distributors, see Page 43.

24 On floor CATALOGUE GROUP 55-AIK On floor electrical installation trunking The on floor installation trunking AIK is used in projects to redevelop old buildings and has all the benefits of an underfloor trunking with respect to capacity and connection flexibility. All that is required for it to be added to the existing floor construction are holes through the walls. The on floor installation trunking AIK consists of a base tray section made of pre-galvanised sheet steel, which is attached to the floor with screws or dowels. Single compartment trunking base can be separated into 2 or 3 compartments using max. 2 partition walls. AIKA Branch trunking, with angles on both side as junction trunking at room depth, available on request. te li tank For insert nuts, see Cat. Gr. 56 te li tank. The trunking cover, which can be walked on, is made of 3 mm sheet steel (or 4 mm sheet steel for 350 mm nominal size) and is screwed to the base tray section before the flooring is glued onto it. Part no. Code H 1 B B tot. 3 ca. 45 Trunking base tray Included: 1 slot-in aluminium side profile in standard length and 6 short lengths to fix the trunking cover. Length supplied: 2400 mm. Material: sheet steel: galvanised. Nom. B H=40 H=70/75 length Btot Btot Single compartment H = 40mm H = 70mm H = 75mm B = 150mm 200mm 250mm B = 200mm 250mm B = 350mm A AIK/U A AIK/U A AIK/U B AIK/U B AIK/U A AIK/U35075 Trunking cover Fits the bottom section of the trunking, inc. 6 fitting screws, fits the screw nut on the aluminium side profile. Material: sheet steel, pre-galvanised (NA). Height for AIK bottom section 40,70, 75 mm. * te li tank pedestal units for installation of 4-12 installation devices, see Cat. Gr. 56 te li tank. AIKF/D blanking Length supplied: 800 mm suitable for: H = 40 mm H = 70 mm AIKF/D B B B C H = 75 mm C Additional option te li tank B = AIK width 150mm 200mm 250mm T4B x x x T6L - x x T12L - - x - DAT - With fitting opening for fitting a te li tank* Fits 40 mm AIK base tray sections Length supplied: 800 mm. AIKF/DAT/ B B B

25 On floor 25 CATALOGUE GROUP 55-AIK Trunking cover Fits the base tray section of the trunking, inc. 6 fitting screws, fits the screw nut on the aluminium side profile. The installation opening is sealed with a 3 mm thick cover blanking plate. For 70 mm AIK base tray sections. Material: sheet steel, pre-galvanised (NA). Part no. Code - DG 2 - For fitting a GES 2 flush floor unit** For 2 installation devices: Length supplied: 800 mm. - DG 2/2 -For fitting 2 GES 2 flush floor unit** For 2 installation devices each: Length supplied: 800 mm. - DG 4 - For fitting a GES 4 flush floor unit** For 4 installation devices: Length supplied: 400 mm. - DG 6 -For fitting a GES 6 flush floor unit** For 6 installation devices: Length supplied: 400 mm. - DG 9 -For fitting a GES 9 flush floor unit** For 9 installation devices: Length supplied: 400 mm. AIK/F/DG2/ C C AIK/F/DG2/ C C AIK/F/DG4/ B AIK/F/DG6/ B AIK/F/DG9/ B ** Flush floor service units GES 2, GES 4, GES 6, GES 9 for the fitting of 2-9 installation units, see Cat. Gr GES. Trunking partition piece AIK6TW - For internal separation of the single comp. trunking base tray section/ AIK/U Material: 1.4 mm sheet steel, pre-galvanised. L = 2400 mm. H = 40 mm H = 70 mm Trunking partition piece AIK/TWL - For the internal separation and cover support of the single line duct bottom section AIK/U Material: 1.4 mm sheet steel. L = 2400 mm. Earth conductor clamp - 8 AWR For use in the base tray section of the trunking and in the internal groove of the AIK side profile. Material: steel, galvanised, yellow passivated. Terminal range: 2 x mm 2 Supplied in packs of 10 AIK trunking corner cover Mitred 2-part cover for right-angle duct turns. Material: 3-mm sheet steel, pre-galvanised (NA). Standard length supplied: 800 mm. AIK trunking internal corner cover Including 10 fixing screws. AIK trunking external corner cover Including 8 fixing screws. Part no. Code A AIK6TW B AIK6TW70z B AIK/TWL CV *AWR Part no. Code B AIKF/IEA B AIKF/IEA C AIKF/IEA B AIKF/IEA C AIKF/IEA B AIKF/IEA B AIKF/AEA B AIKF/AEA C AIKF/AEA B AIKF/AEA C AIKF/AEA B AIKF/AEA35075 Trunking partition pieces AIK/TWL75 with fitting for earth conductor clamp 8 AWR. AIK trunking end cap AIK/ES AIK trunking end caps AIK/ES with connection terminal for earth continuity (up to 4 mm). Material: sheet steel, pregalvanised with left-handed edge AIK/ESL. suitable for H = 40 mm H = 40 mm H = 40 mm H = 70 mm H = 70 mm H = 75 mm B2 AIK/ESL B2 AIK/ESL B2 AIK/ESL C2 AIK/ESL C2 AIK/ESL B2 AIK/ESL35075 With right-handed edge AIK/ESR. H = 40 mm H = 40 mm H = 40 mm H = 70 mm H = 70 mm H = 75 mm B1 AIK/ESR B1 AIK/ESR B1 AIK/ESR C1 AIK/ESR C1 AIK/ESR B1 AIK/ESR35075 For other trunking designs and accessories, see Catalogue screed-flush electrical installation systems for installation devices.

26 26 Te li Tanks CATALOGUE GROUP 56-TE LI TANK - te li tank Pedestal service outlet units For fitting to electrical installation systems EÜK, OKA2, OKU, DB, HB and AIK te li tank T4B Te li tanks are installation units which project above the floor, used for installation devices for power, telecommunications and data. The various types of current are segregated from one another by means of partition walls. These installation units are available in various different sizes as a function of the number of installation devices to be fitted. They are generally fitted to junction boxes and trunking covers in which the appropriate holes have been made. Another option is to drill the trunking subsequently. However, it does not matter whether the floor is screed, stone tiles, wood, vinyl or carpet. The size of the trunking with the holes in is also irrelevant. Te li tanks have ground seals which prevent water getting into the underfloor trunking system when the floor is mopped. te li tanks must not be positioned in high-traffic areas and they must be arranged to fit with the furniture in the room. Care should be taken to ensure that they are placed as near as possible to or underneath the working equipment, so there is no risk of tripping over the casings and connecting cables. See the Workplace Ordinance and Safety Regulations for Office Workplaces from the Administrative Trade Association: Pedestal units which project above the floor must not be fitted in transport areas. 4 T/EM insert nuts must be used to fit the te li tanks to junction boxes or trunking covers. te li tank T8NL te li tank T4L te li tank T12L

27 Te li Tanks 27 CATALOGUE GROUP 56-TE LI TANK L B H te li tank T4B* With partition wall and no cover plates to fit 4 installation devices of the same voltage rating or 2x2 installation devices of 2 different voltage ratings. Material: polyamide. Colours available Housing grey-beige RAL 1019 Base sepia brown RAL Housing iron-grey RAL 7011 Base graphite RAL Part no. Code A2 T4B00C/ A4 T4B00C/7011 te li tank T4B * fixing screws provided. Strain-relief mechanism can be fitted, see accessories, Installation devices for fitting to te le tank, see Cat. Gr. 78 fitting and connection devices for electrical installation systems. Example T4B configuration Housing graphite RAL 9011 Base graphite RAL A4 T4B00C/9011 1/2 cover plates Dimensions: 55 x 77 mm. - T4B/P01 blanking. sepia brown graphite G1 T4B/P01B GA T4B/P01S ** Detailed view of 45 mm perforation - T4B/P1 round-perforated** for EK installation devices only. sepia brown graphite E1 T4B/P1B EA T4B/P1S 45 1/1 cover plates Dimensions: 110 x 77 mm - T4B/P02 blanking. sepia brown graphite - T4B/P2 round-perforated.** sepia brown graphite - T4B/P3 round-perforated** for 2 EK installation devices only. sepia brown graphite Cover plates - T4B/P6 1/2 length For one gang schuko or NF outlet Ackermann type. Dimensions: 55 x 77 mm. sepia brown graphite - T4B/P6 1/1 length For two gang schuko NF outlet Ackermann type. Dimensions: 110 x 77 mm. sepia brown graphite Cover plate - T4B/P5 for CEE 16 A or 32 A Fixing track 60 x 60 mm. sepia brown graphite F1 T4B/P02B FA T4B/P02S A1 T4B/P2B AA T4B/P2S C1 T4B/P3B CA T4B/P3S AD T4B/P6B AA T4B/P6S BD T4B/P7B BA T4B/P7S D1 T4B/P5B DA T4B/P5S Not suitable for installation devices with a round central insert in accordance with DIN Important: Cover plates with square or rectangular fitting openings are only suitable for fitting an Ackermann power socket outlet. Slot the sockets into the cover plate before connecting. Cross partition wall T4 B/TQ For additional partitioning of the interior in accordance with the sketch opposite C T4B/TQ Internal partitioning of te li tank T4B.

28 28 Te li Tanks CATALOGUE GROUP 56-TE LI TANK Part no. Code T4L and T8NL te li tank T4L application For the combined installation for 4 individual installation devices for power, data and telecommunications. Note: If fitting a 3 gang schuko outlet and 1 or 2 installation devices of other current types, the installation casing T4L/EG should be used as well. L B H - te li tank T4L - No cover plates, for fitting 4 individual installation devices of different voltage ratings. Material: polyamide. Dimensions in mm: L = 225, B = 125, H = 125. Colours available: Housing light grey RAL 7035 Base iron grey RAL Housing and base graphite RAL AA T4L00C AF T4L00C9011 T8NL application For the combined installation of 8 individual devices for power, data and telecommunications. Devices with different voltage ratings are insulated from one another by a partition. If using multiple installation devices, the connection capacity can be increased. Suitable for floor mounting. L B H -te li tank T8NL No cover plates, for fitting 8 individual installation devices of different voltage ratings. Material: polyamide. Dimensions in mm: L = 225, B = 225, H = 125. Colours available: Housing light grey RAL 7035 Base iron grey RAL Housing and base graphite RAL AA T8L00C AF T8L00C9011 T4L and T8NL version Screw fixing line for installation devices: 60 mm vertical. Housing base with seal, fixing screws included. - T8NL/EB Corner cover for subsequent installation in the te li tank housing. Material: polyamide. Supplied in packs of 2. Version curved inwards. graphite light grey Version curved outwards. graphite light grey AF T8NL/EB1/ AM T8NL/EB1/ BF T8NL/EB1/ BM T8NL/EB1/ T4L/EG - Installation housing for insulated installation of a combination of single+single or a 3 gang schuko socket outlet, Ackermann type, in te li tank T4L Material: polyamide A T4L/EG Cover plates for T4L and T8NL - T8NL/A Adapter for fitting Ackermann sockets under S 99 cover plates. For 1 gang schuko or NF outlet. For 2 and 3 gang schuko or NF socket outlet A T8NL/A B T8NL/A105 - T8NL/P01 Blanking, fits to narrow side and 1 /2 long side. graphite light grey DF T8NL/P01/ DM T8NL/P01/ T8NL/PCEE - For a CEE socket, fits narrow side (CEE 16 and 32 A) and 1 /2 long side (CEE 16 A only). graphite light grey CF T8NL/PCEE/ CM T8NL/PCEE/7035

29 Te li Tanks 29 CATALOGUE GROUP 56-TE LI TANK Part no. Code - T8NL / P45 For single Ackermann-type schuko or NF socket outlet, fits narrow side and long side. Cover plates for T4L and T8NL graphite light grey AF T8NL/P45/ AM T8NL/P45/ T8NL / P105 For 3 gang Ackermann-type schuko or NF socket outlet, fits long side. graphite light grey BF T8NL/P105/ BM T8NL/P105/ T8NL / P1 For installation devices with a 50º central plate, fits narrow side. graphite light grey EF T8NL/P1/ EM T8NL/P1/ T8NL / P2 For a single installation device with a 50º central plate, fits 1 /2 long side. graphite light grey FF T8NL/P2/ FM T8NL/P2/ T8NL / P3 For 2 installation devices with a 50º central plate, fits long side. graphite light grey GF T8NL/P3/ GM T8NL/P3/ T8NL / TQ Cross partition for internal insulation of T4L and T8NL te li tanks. Material: polyamide A T8NL/TW Accessories for T4L and T8NL - ZE2/3 strain relief - For use in T4L and T8NL te li tanks Material: polyamide. Supplied in packs of AV ZE2/3

30 30 Te li Tanks CATALOGUE GROUP 56-TE LI TANK Device installation with S 99 installation device cover plates Device installation Ackermann type power socket outlet Device installation Standard installation devices with holder ring Part no. Code Front snap-in cover plates for power socket outlets 45 B H S99-AF1 single To cover an Ackermann single power socket outlet A..* S99-AF1/..* S99-AF2 2 gang To cover an Ackermann 2 gang power socket outlet B..* S99-AF2/..* S99-AF3 3 gang To cover an Ackermann 3 gang power socket outlet C..* S99-AF3/..* Front snap-in cover plates for S99 installation devices * Standard colours for S99 cover plates For the colour you want: add 50 B H S99 AF18 single To cover an installation device with a 50º central plate A..* S99-AF18/..* - the RAL no. to the code - the letter to the Part no. Colour RAL code Letter cream 9001 B white 9010 K light grey 7035 M 50 S99 AF18 2 x single To cover two installation devices with a 50º central plate B..* S99-AF28/..*

31 Te li Tanks 31 CATALOGUE GROUP 56-TE LI TANK Part no. Code H L B te li tank T12L With seal and partition wall, including 4 fixing screws, suitable for installation of 12 installation devices of the same voltage rating or 2x6 installation devices of 2 different voltage ratings. The interior can be divided still further using cross partition wall. Screw fixing track for installation devices: 60 mm. Dimension in mm: L = 375, B = 154, H = T12L te li tank T12L example configuration F N Material: Base and housing made of polyamide. Cover plates for Ackermann power socket outlets made of polyamide. Cover plates and cross partition all made of plastic moulding compound. Colours available: Housing in grey-beige RAL 1019 Base in sepia brown RAL Housing in iron grey RAL 7011 Base in graphite RAL Housing and base in graphite RAL A T12L00C/ A3 T12L00C/ AA T12L00C/9011 Cover plates to fit _ long side or _ narrow side of the te li tank T12L Dimensions: 71 x 88 mm T12L/P01 blank. sepia brown graphite J1 T12L/P01B JA T12L/P01S T12L/P1 round-perforated* for installation devices. sepia brown graphite T12/P15 for one gang Ackermann type power socket outlet. sepia brown graphite Cover plates to fit _ long side of the te li tank T12L Dimensions: 142 x 88 mm A1 T12L/P1B AA T12L/P1S AD T12L/P15B AA T12L/P15S Note: Cover plates with square or rectangular fitting openings are only suitable for fitting an Ackermann power socket outlet. Slot the sockets into the cover plate before connecting. T12L/P02 - blank. sepia brown graphite K1 T12L/P02B KA T12L/P02S T12L/P1 round-perforated* for 2 installation devices. sepia brown graphite B1 T12L/P2B BA T12L/P2S Cover plates to fit _ long side of te li tank T12L Dimensions: 213 x 88 mm. *Detailed view of 45 mm perforation. T12L/P03 - blank. sepia brown graphite L1 T12L/P03B LA T12L/P03S 45 T12L/P3 round-perforated* for 3 installation devices. sepia brown graphite C1 T12L/P3B CA T12L/P3S Not suitable for installation devices with a round central insert in accordance with DIN

32 5 32 Te li Tanks CATALOGUE GROUP 56-TE LI TANK Part no. Code Cover plate to fit 1 long side of te li tank T12L Dimensions: 284 x 88 mm. T12L/P04 - blank. T12L/P4 round-perforated* for 4 installation devices. sepia brown graphite sepia brown graphite M1 T12L/P04B MA T12L/P04S D1 T12L/P4B DA T12L/P4S Cover plate to fit _ long side of te li tank T12L Dimensions: 94.5 x 88 mm. T12L/P05 - blank. T12L/P7 / 63.5 mm hole 60 x 60 mm screw fixing track for CEE sockets. sepia brown graphite sepia brown graphite N1 T12L/P05B NA T12L/P05S G1 T12L/P7B GA T12L/P7S Note: Cover plates with square or rectangular fitting openings are only suitable for fitting an Ackermann power socket outlet. Slot the sockets into the cover plate before connecting. Cover plate to fit 1/3 long side of te li tank T12L Dimensions: 94.5 x 88 mm. T12/P16 for 2 gang Ackermann-type power socket outlet. sepia brown graphite BD T12L/P16B BA T12L/P16S *Detailed view of 45mm perforation 45 Cover plate to fit _ long side of te li tank T12L Dimensions: 142 x 88 mm. T12L/P17 for 3 gang Ackermann-type power socket outlet. sepia brown graphite CD T12L/P17B CA T12L/P17S Not suitable for installation devices with a round central insert in accordance with DIN Cross partition T12L/TQ - For additional internal partitioning of a te li tank T12L D T12L/TQ Accessories for T4B and T12L Strain relief For sleeve cables of up to / 16 mm, for fixing to the partition walls of the individual types of te li tank. 1 to 5 units can be used depending on the te li tank type Version T4B T12L Units 2 5. Supplied in packs of T/ZE 5 Insert nuts For fixing te li tanks T4B, T4L, T8NL and T12L to junction box or trunking covers. For installation devices to be fitted into te li tank, see Cat. Gr. 78 Installation and connection devices for electrical installation systems. Supplied in packs of T/EM

33 Underfloor 33 CATALOGUE GROUP 57-GES 110 Service outlet GESR.2US - With carpet protection frame. Design and materials as described on the right. Installation diameter: 120 mm. Design for screed system UZD/UDL Standard finish: Nickel Alternative: Old brass Old copper Chrome Design for raised / hollow floor Standard finish: Nickel Alternative: Old brass Old copper Chrome Service outlet GESR.2UA - with flush floor guide frame. Design and materials as described on the right. Design for screed system UZD/UDL Standard finish: Nickel Alternative: Old brass Old copper Chrome Underfloor box UDL For installation of a GESRM 2 service unit. For floor thicknesses of 60 to 75 mm. For floor thicknesses of 72 to 91 mm. (floor thickness = screed + flooring). Part no. Code DA GESRN2USB GA GESRMS2USB CA GESRK2USB EA GESRC2USB DA GESRN2HS GA GESRMS2HS CA GESRK2HS EA GESRC2HS DA GESRN2UAB GA GESRMS2UAB CA GESRK2UAB EA GESRC2UAB B UDL1-120/ C UDL1-120/91 Flush floor service unit For installation in underfloor systems (UZD and UDL 1-120) and hollow/raised floors. service unit GESR.2 Application Use in dry clean floors for fitting a power socket outlet and up to two RJ45 connection sockets. Notes Can also be cleaned wet when not in use. Design The device insert consists of: Installation housing with carpet protection frame or flush floor mounting frame. Adjustment ring with clamps to suit either hollow or raised access floors. Hinged lid can be secured in 2 positions. In the raised position the lid acts as the cord outlet protecting the cables where they exit the grommet. Mounting box supplied with pre-fitted schuko socket. Child proof lock on lid, separate compartment for installation of data. Available in four high quality finishes. Nickel Antique Brass Antique Copper Chrome Mounting plates For fitting WE8S80 unshielded RJ45A connection sockets in GESR-2 in order to connect telecommunications equipment. Material: Installation casing and cover: die-cast zinc, mounting box: polyamide. MPR2S80 For the fitting of awe8s80 unshielded RJ45 connection socket. MPR2/WAEGM For the fitting of two WAEGM STP/UTP RJ45 connection sockets B MPR2S H MPR2WAEGM Design of carpet protection frame Seal provided on-side MPR2/2WAEG6C-MK For the installation of 2 shielded WAEG6C-MK RJ45 connection sockets J MPR2/2..WAEG6C-MK MPR2 XD For fitting round slot-in connectors with a 24 mm diameter (e.g. XLR type D, Speakon). Material: V2A E MPR2XD Design of flush floor mounting frame RJ45 connection modules WE8 S80 RJ45 compact module, Cat. 3 with strain relief. Supplied singly JG WE8S80 WAEGM UTP RJ45 compact module, UTP, Cat 5. AWG 24, 26. Supplied singly CA WAEGM/UTP WAEGM-STP RJ45 compact module, STP, Cat 5. AWG 24, 26. Supplied singly CC WAEGM/STP WAEG6C-MK RJ45 compact module, shielded, Cat. 6, AWG 24, 26. Supplied in packs of QL WAEG6C-MK

34 34 Underfloor CATALOGUE GROUP 57-GES Device installation in underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow / raised floors - Dry-cleaned floors Flush floor service unit GES2, 4, 4/10, 6, 6/10, 9 Flush floor service unit GES 2 For 2 installation devices in 1 GB 2 mounting box. External dimension in mm: L = 194, W = 118. Installation opening in mm: L = 198, W = 105. Application Use in dry-cleaned floors for the fitting of installation devices in insulated mounting boxes. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 The number of individual installation devices to be fitted is as follows: GES 2: 2 units GES 4 and GES 4/10: 4 units GES 6 and GES 6/10: 6 units GES 9: 9 units If using multiple installation devices, the number of connections available increases accordingly. Design Flush floor service unit consist of: Carpet protection frame, including fitting bracket (hollow floor: split pin for raised floor and screed system: fitting bracket). Mounting box insert frame with ladders to lower the mounting box in 5 mm increments to a max. of 20 mm. Hinged cover (captive in carpet protection frame, closes automatically), including: 4 mm steel plate. Cord cap with foam seal. Adjustable handle to open the cover. Carpet recess: 5 mm, 10 mm only for /10 flush floor service unit. Minimum fitting depth for flush floor service unit: 70 mm, 75 mm for GES 4/10 and GES 6/10. Material Carpet protection frame and cover with cord cap: polyamide. Flush floor service unit GES 4 For 4 installation devices in 2 GB 2 mounting box. Installation opening in mm: L = W = 201. GES 4 With 5 mm carpet recess. External dimensions in mm: L = W = 217. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 GES 4/10 With 10 mm carpet recess. External dimensions in mm: L = W = 220. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Flush floor service unit GES 6 For 6 installation devices in 3 GB 2 mounting box. Installation opening in mm: L = 253, W = 200. GES 6 With 5 mm carpet recess. External dimensions in mm: L = 270, W = 215. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 GES 6/10 With 10 mm carpet recess. External dimensions in mm: L = 276, W = 220. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Flush floor service unit GES 9 For 9 installation devices in 3 GB 3 mounting box. External dimension in mm: L = W = 263. Installation opening in mm: L = W = 243. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 For mounting box and cover plates, see page 38 and following. For installation devices see Cat. Gr. 78 Installation and connection devices for electrical installation systems. Fitting bracket attachment GES.BG As a replacement for fitting flush floor service unit and carpet protection frame in hollow/raised floors. Clamping range: max. 50 mm. Fits: GES4DB, GES6DB, GES9DB Supplied in packs of 4. All flush floor service units are halogen-free. Slot in cable extension GES/RV For additional lowering of the mounting box by max. 25 mm. Fits all flush floor service units. Supplied in packs of 2.

35 Underfloor 35 CATALOGUE GROUP 57-GES 53 Hollow floor Part no. Code 54 Raised floor Part no. Code Screed system EÜK, OKA, OKU, AIK Part no. Code A GES2/ E GES2/ F GES2/ A1 GES4DB E1 GES4DB F1 GES4DB A GES4/ E GES4/ F GES4/ A GES4/10/ E GES4/10/ F GES4/10/ A1 GES6DB E1 GES6DB F1 GES6DB A GES6/ E GES6/ F GES6/ A GES6/10/ E GES6/10/ F GES6/10/ A1 GES9DB E1 GES9DB F1 GES9DB A GES9/ E GES9/ F GES9/ M GES4BG A1 GES/RV A1 GES/RV

36 36 Underfloor CATALOGUE GROUP 57-GES Device installation in underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow / raised floors Dry-Cleaned floors Flush floor service unit GESR4, R7, RA7/10, R9, R9SR Application Use in dry-cleaned floors for the fitting of installation devices in insulated mounting boxes. The number of individual installation devices to be fitted is as follows: GESR4: 4 units. GESR7 and GESRA7/10: 7 units. GESR9: 9 units. If using multiple installation devices, the number of connections available increases accordingly. Design Flush floor service unit consist of: Carpet protection frame, including fitting bracket (hollow floor: split pin for raised floor and screed system: fitting bracket). Mounting box insert frame with ladders to lower the mounting box in 5 mm increments to a max. of 20 mm. Hinged cover (captive in carpet protection frame, closes automatically), including: 4 mm steel plate. Cord cap with foam seal. Adjustable handle to open the cover. Carpet recess: 5 mm, 10 mm GESR(A)7/10.. Minimum fitting height for flush floor service unit: 70 mm, 75 mm for GESR7/10 and GESRA7/10. Material GESR: Carpet protection frame and hinged cover with cord cap: polyamide. GESRA7/10: Carpet protection frame and hinged cover made of die-cast aluminium, cord cap made of polyamide. Note for GESR7/10 The carpet recess can be deepened from 5 mm to 10 mm on-site. This requires the UDB conversion kit. For mounting boxes and cover plates, see page 38. For installation devices see Cat. Gr. 78 Installation and connection devices for electrical installation systems. All flush floor units are halogen-free. Flush floor service unit GESR 4 For 4 installation devices in 2 GB 2 mounting boxes. External dimension: = ø228mm. Installation opening: = ø215mm. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Flush floor service unit GESR 7 For 7 installation devices in 2 GB 2 and 1 GB3 mounting boxes. External dimension: = ø295mm. Installation opening: = ø275mm. GESR 7/10 Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 GESRA 7/10 Material: carpet protection frame and hinged cover made of die-cast aluminium (steel ball polished). Flush floor service unit GESR 9 For 9 installation devices in 3 GB 3 mounting boxes. External dimension: = ø325mm. Installation opening: = ø305mm. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Flush floor service unit GESR 9SR With additional carpet protection frame in hinged cover to prevent flooring from becoming detached. Installation opening: = ø305mm. Standard colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Conversion kit UDB To allow on-site conversion of a GESR7 device insert to a 10 mm carpet recess. Supplied in packs of 4. Fitting bracket attachment GES.BG As a replacement for fitting device inserts and carpet protection frame in hollow/raised floors. Clamping range: max. 50 mm. Fits: GESR4DB Supplied in packs of 4. Fits: GESR7DB, FSR9DB Supplied in packs of 6. Ladder extension GES/RV For additional lowering of the mounting box by max. 25 mm. Fits all flush floor service units. Supplied in packs of 2.

37 Underfloor 37 CATALOGUE GROUP 57-GES 53 Hollow floor Part no. Code 54 Raised floor Part no. Code Screed system EÜK, OKA, OKU, AIK Part no. Code A4 GRHB4/ E4 GRHB4/ F4 GRHB4/ A1 GESR4D/ E1 GESR4D/ F1 GESR4D/ A GESR/ E GESR/ F GESR/ A2 GRHB7/10/ E2 GRHB7/10/ F2 GRHB7/10/9011 GESR7/10DB A E F GESR7/ A E F A2 GRAHB7/ A1 GESRA7/10DB A GESRA7/ A2 GRHB9/ E2 GRHB9/ F2 GRHB9/ A1 GESR9DB E1 GESR9DB F1 GESR9DB A GESR9/ E GESR9/ F GESR9/ A2 GRHB9S E2 GRHB9S F2 GRHB9S9011 GESR95RDB A E F GESR9S A E F DE UDB DE UDB DE UDB M GES4BG N GES6BG A1 GES/RV A1 GES/RV A1 GES/RV

38 38 Underfloor CATALOGUE GROUP 57-GES Mounting boxes and cover plates Part no. Code Application For use in flush floor service unit GES 2, GES(R) 4, GES 6 and GESR 7, plus the hollow floor and raised floor versions. Enables the combined installation of two individual installation units for power, telecommunications and data. If using multiple installation devices, the number of connections available increases accordingly. Note: The total length of the cover plates must be 165 mm! So, for example: 2 cover 82.5 mm. 1 cover 61 mm and 1 cover 104 mm. Each cover plate can be used on either the left or right-hand side of the mounting box. Material: Polyamide, halogen-free. Fitting the connection devices Mounting boxes and cover plates enable screw-free fitting of connection devices. Ackermann power sockets are snapped into the cover plate provided before connecting the cable. Installation devices with a holder ring or holder bracket are snapped against the mounting box cover plate from underneath after the cable is connected. Strain-relief brackets are plugged into the cover plate. All cover plates are snapped into the mounting box without screws. Important: Devices with different voltage ratings in the same mounting box must be separated using a GB2/3 TW partition piece. Mounting box GB 2 - Empty suitable for the installation of 2 individual installation devices, with 2 strain relief brackets for incoming and outgoing cables. Dimensions in mm: L=165 W=76 D=39 Mounting box cover plates For blanking GB 2 mounting box. Material: polyamide, black RAL GB2/3 P01 L = 61 mm GB2 P01 L = 82.5 mm Mounting box cover plates For GB2 mounting box, for fitting an installation device with a holder bracket (EK version). Material: polyamide, black RAL GB2/3 P1 L = 61 GB2 P1 L = 82.5 mm (Also suitable for installation device with holder ring, EKR version). GP2/3 P5 L = 104 mm. With 60 mm screw-connection line, for WAEG6-K50. Mounting box cover plates GB 2 device holders, for fitting of an Ackermann power socket. Material: polyamide, black RAL 9011 GB2/3 P3 For fitting a 1 gang power socket. L = 61 mm GB2/ P2 For fitting a 1 gang power socket. L = 82.5 mm GB2/3 P4 For fitting a 2 gang power socket. L = 104 mm GB2 P3 For fitting a 3 gang power socket. L = 165 mm A GB A GB2/3P A GP2P B GB2/3P B GP2P G GB2/3P C GB2/3P C GB2P D GB2/3P D GB2P3 Accessories for mounting boxes GB 2 and GB 3 Blank slot cover Mounting box partition piece GB2/3 TW Made of polyamide. Labelling panel BF1 To be slotted into mounting box cover plates. Strain relief bracket ZE 2/3 Made of polyamide. For use in mounting box cover plates or in GB 2 and GB 3 mounting box Supplied in packs of 10. Blank slot cover For blanking of a fitting opening in a mounting box cover plate. Material: polyamide, black RAL 9011 LP 45 for square opening. LP/R for round opening A GB2/3TW A BF AV ZE2/ E LP F LP/R

39 Underfloor 39 CATALOGUE GROUP 57-GES Mounting box Empty suitable for the installation of 3 individual installation devices with holder brackets, with 2 strain relief mechanisms for incoming and outgoing cables. Dimensions in mm: L=208 W=76 D=39 Mounting box cover plates For blanking GB 2 mounting box. Material: polyamide, black RAL GB2/3 P01 L = 61 mm A GB2/3 P02 L = 104 mm A GB3 P01 L = 147 mm B Mounting box cover plates For GB3 mounting box, for fitting an installation device with a holder bracket (EK version). Material: polyamide, black RAL GB2/3 P1 L = 61 mm GB2/3 P2 L = 104 mm (Also suitable for installation device with holder ring, EKR version). GB3 P1 L = 147 mm Part no. Code A GB A GB2/3P A GB2/3P B GB3P B GB2/3P C GB2/3P D GB3P1 Application For use in flush floor box GESR 7, GES 9 and GESR 9, plus the hollow floor and raised floor versions. Enables the combined installation of three individual installation units for power, telecommunications and data. If using multiple installation devices, the number of connections available increases accordingly. Note: The total length of the cover plates must be 208 mm! So, for example: 2 cover 104 mm or 1 cover 61 mm and 1 cover 147 mm. Each cover plate can be used on either the left or right-hand side of the device holder. Material: Polyamide, halogen-free. Fitting the connection devices Mounting boxes and cover plates enable largely screw-free fitting of connection devices. Ackermann power sockets are snapped into the cover plate before connecting the cable. Installation devices with a holder ring or holder bracket are snapped against the Mounting box cover plate from underneath after the cable is connected. All cover plates are snapped into the Mounting boxes without screws. Important: Devices with different voltage ratings in the same mounting box must be separated using a GB2/3 TW partition piece. GB3 P2 L = 208 mm E GB3P2 GP2/3 P5 L = 104 mm With 60 mm screw-connection line, for WAEG6-K G GB2/3P5 Mounting box cover plates For GB3 mounting box, for fitting an Ackermann power socket. Material: polyamide, black RAL GB2/3 P3 For fitting a 1 gang power socket. L = 61 mm C GB2/3P3 GB2/3 P4 For fitting a 2 gang power socket. L = 104 mm D GB2/3P4 GB3 P3 For fitting a 3 gang power socket. L = 147 mm F GB3P3

40 40 Underfloor CATALOGUE GROUP 57-GES NEW data installation in underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow / raised floors Installation of data connection sockets Application For snap-in installation of modular connection systems in GES flush floor service unit. Design Universal holder for carrier plates with insertion holes for snapping into mounting box GB 2/GB 3 or fitting holder MT2GBEU/MT3GBEU. Fitting holder with strain relief options for cable ties. Minimum fitting depth of device installation insert: 90 mm. Universal holder GBE-U For snap-in fitting of modular connection systems, consisting of a holder, hood and end piece. Fitting holder MT2GBEU For the fitting of 2 GBE-U universal holders to fit GES 2, 4, R4, 6, R7 and 8 flush floor service unit. Fitting holder MT3GBEU For the fitting of 3 GBE-U universal holders to fit GES R7, 9 and R9 flush floor service units. Part no. Code AV GBE-U D MT2GBEU E MT3GBEU Fitting options GB2 and MT2GBEU: 2 x GBE-U universal holder. GB3 and MT3GBEU: 2 x GBE-U universal holder. Material: Universal holder and dust-protection flap: polyamide. Holder plate: sheet steel, unpainted. Fitting holder: V2A. Dust protection flap GBE-U/SSK For sealing connection sockets which are not in use. Supplied in packs of AV GBE-U/SSK Holder plates: Design - Blanking. For snap-in connection systems: 2 x WE 8 2 x WAEGM 2 X WAEG6/C 2 x D-SUB 9 2 x ACO 2 x WAEG6C-MK/EMT 3 x 110connect 2 x ST 2 x SCD 1 x XLR A GBE-U/ B GBE-U/WE R GBE-U/WAEGM L GBE-U/WEAG6C D GBE-U/TSG G GBE-U/ACO H GBE-U/EMT J GBE-U110C P GBE-U2ST Q GBE-U2SCD V GBE-U/XLR RJ45 connection modules for fitting in universal holders For installation devices, see Cat. Gr. 78 Installation and connection devices for Electrical Installation Systems. RJ45 connection modules WE 8S80 RJ45 compact module Cat 3, with strain relief Supplied singly. WEAGM UTP RJ45 compact module UTP, Cat 5, AWG 24, 26 Supplied singly. WEAGM STP RJ45 compact module STP, Cat 5, AWG 24, 26 Supplied singly. WAEG6C-MK RJ45 compact module shielded, Cat 6, AWG 24, 26 Supplied in packs of J3 WE8S CA WAEGM/UTP CC WAEGM/STP QL WAEG6C-MK

41 Underfloor 41 CATALOGUE GROUP 57-GES Assembly holder MT For fitting 2 to 3 WAEG6-K50 connection sockets with a holder bracket into flush floor service unit: GES2, 4, R4, 6, R7 GESR7, 9, R9 Material: sheet steel, graphite RAL 9011 Part no. Code FA MT2WAEG6K BA MT3WAEG6K50 Device installation in underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow/raised floors. Over-voltage protection module - ÜSM4 - With acoustic fault display, no mains disconnection, for connection of a single or multiple socket. For fitting into mounting box GB2 and GB 3 using divider piece provided. REG installation unit MSREG For installation of circuit breaker switch or RCD in mounting box GB2 or GB3: Version for: 1 module device 2 module device SE USM A MSREG B MSREG2 ÜSM technical specifications Rated voltage: 230 V AC. Rated derived current: 2.5 ka/5ka (8/29 µs). Noise level: <= 1.5 kv. Initial fuse: max. 16 A gl. Short-circuit resistance: 6 ka/50 Hz. The over-voltage protection module complies with requirement class D in accordance with E DIN VDE and 6A1 and SPD type 3 in accordance with EN :2001. Assembly holder - MT For slot-in connection systems. on request Simple snap in fitting of installation devices a) b) a) The benefits to you Screw-free fitting of sockets into cover plates. Screw-free connection of cables into sockets. Simple fitting of installation devices with holder rings/brackets. Screw-free strain relief. Covers snap straight into device holders without using screws. Increased fitting space in the device holder. b) = simple, time-saving electrical installation

42 42 Underfloor CATALOGUE GROUP 57-GES Pre-wired mounting boxes for connection to underfloor distribution systems - to fit GES 2, GES(R)4, GES 6 and GESR(A) 7 Mounting box AGB2 Pre-wired with 3 gang 16 A schuko socket, including H05VV-F3G connection cable with 3-pin plug, with lock to fit VL extension cables. Cable cross section 1.5 mm 2, L = 0.6 mm Cable cross section 2.5 mm 2, L = 0.8 mm Part no. Code B AGB2/0.7/3CW B AGB2/1/3CW2.5 - to fit GESR(A) 7, GES 9 and GESR 9 Mounting box AGB2 S Pre-wired with one gang schuko socket (white) and one gang schuko socket (orange) with over-voltage protection module, including 2 x H05VV-F3G connection cable with 3-pin plug, with lock to fit VL extension cables. Cable cross section 1.5 mm 2, L = 0.6 mm Cable cross section 2.5 mm 2, L = 0.8 mm Mounting box AGB3 Pre-wired with 3 gang 16 A schuko socket and 1 gang schuko socket (orange), including 2 x H05VV-F3G connection cable with 3-pin plug, with lock to fit VL extension cables. Cable cross section 1.5 mm 2, L = 0.6 mm Cable cross section 2.5 mm 2, L = 0.8 mm AGB2/0.7/ B 1CW1ORS AGB2/1/ B 1CW1ORS2.5 AGB3/0.7/ B 3CW1OR AGB3/1/ B 3CW1OR2.5 Mounting box AGB3 Pre-wired with 2 gang 16 A schuko socket and 2-way schuko socket (orange), including 2 x H05VV-F3G connection cable with 3-pin plug, with lock to fit VL extension cables. Cable cross section 1.5 mm 2, L = 0.6 mm Cable cross section 2.5 mm 2, L = 0.8 mm Mounting box AGB3 S Pre-wired with 2 gang schuko socket and 2 gang schuko socket with overvolt protection (orange), including 2 x H05VV-F3G connection cable with 3-pin plug, with lock to fit VL extension cables. Cable cross section 1.5 mm 2, L = 0.6 mm Cable cross section 2.5 mm 2, L = 0.8 mm AGB3/0.7/ B 2CW2OR AGB3/1/ B 2CW2OR2.5 AGB2/0.7/ A 2CW2ORS AGB3/1/ A 2CW2ORS2.5 For pre-wired mounting boxes and underfloor distribution systems, see Catalogue System components for hollow and raised floors with installation devices. Versions with different units and halogen-free cables available on request. Extension cable - VL For connecting the pre-wired connection box to an underfloor distribution system. 1.5 mm 2 black, 4 m 1.5 mm 2 black, 7 m 1.5 mm 2 black, 11 m 1.5 mm 2 black, 14 m 1.5 mm 2 black, 4 m 1.5 mm 2 black, 7 m 1.5 mm 2 black, 11 m 2.5 mm 2 black, 14 m 2.5 mm 2 black, 4 m 2.5 mm 2 black, 7 m 2.5 mm 2 black, 11 m 2.5 mm 2 black, 14 m 2.5 mm 2 White, 4 m 2.5 mm 2 White, 7 m 2.5 mm 2 White, 11 m 2.5 mm 2 White, 14 m D VL/4/S G VL/7/S L VL/11/S P VL/14/S D VL/4/W G VL/7/W L VL/11/W P VL/14/W D VL/4/S G VL/7/S L VL/11/S P VL/14/S D VL/4/W G VL/7/W L VL/11/W P VL/14/W2.5

43 Underfloor 43 CATALOGUE GROUP 57-GES -UVS6S G4 Underfloor power distributor Pre-wired on a three-phase current circuit, with 6x 3-pin self-locking quick-fit plug-in connectors, 16 A. Internal wiring: H07V-U2.5 PVC cable in-feed connection: 5-pin screw-free plug-in terminal box. Part no. Code Underfloor distributor system to pre-wired mounting boxes UVS6.2,5 With terminal block for 2.5 mm 2 cable. Dimensions in mm: 210 x 150 x 45. Black plug-in connector. White plug-in connector. UVS6.4 With terminal block for 4 mm 2 cable. Dimensions in mm: 210 x 150 x 45. Black plug-in connector. White plug-in connector J1 UVS6S J2 UVS6W K1 UVS6S K2 UVS6W4 -UVS 6S6W G5 Underfloor power distributor UVS 6S6W Pre-wired on two three-phase current circuits, with 12 (6ws + 6sw) 3-pin self-locking quick-fit plug-in connectors, 16 A. Internal wiring: H07V-U2.5 PVC cable. Dimensions in mm: 210 x 300 x 45. In-feed connection: 2 5-pin screw-free plug-in terminal boxes for cable. 2.5 mm L1 UVS656W M1 UVS656W4 For further underfloor distributors and pre-wired mounting boxes, see Catalogue System components for hollow and raised floors with installation devices.

44 44 Underfloor CATALOGUE GROUP 57-GES Height-adjustable installation unit for use in dry rooms with drycleaned floors The dome lid can be screwed into trunking outlet US 80 and outlet box UDL 1-80/R16. Polyamide hinged cover and carpet protection frame supplied in matt finish. The hinged cover, which can be rotated 90º, guarantees that the cord outlet opening can be perfectly aligned with the required cable exit direction. The closed hinged cover slots into the carpet protection frame. The cord outlet opening has a foam seal. For flush floor blanking and sealing of the installation device, the dome lid can be replaced with a blanking cover Underfloor outlet USS 80 For fitting of a single installation device or attachment of a te li tank. Material: die-cast zinc. Application Opening Plate thickness EÜK 95 mm HB 95 mm DB 91.2 mm 38 mm DB 91.2 mm 60 mm Underfloor outlet box UDL 1-80 For installation of an SH or SHF heightadjustable installation unit. For screed heights of 60 to 75 mm. Important: Assembly protection cover to be used during screeding only. Part no. Code A US USS80W A USS80DB B USS80DB A UDL1-80/R16 Dome lid SH 80 A Height above floor: 26 mm. External diameter: 104 mm. Materials: polyamide, standard colours. iron grey: RAL 7011 grey-beige: RAL 1019 graphite: RAL A SH80/ E SH80/ F SH80/9011 Device cover plate For fitting of an installation device in US 80 or UDL 1-80/R161). US 80A For installation device with holder ring or bracket US80A US 80B For single Ackermann-type power socket AA US80B Height-adjustable installation unit for use in dry rooms with wetmopped floors Blanking cover BA80N With carpet recess (5 mm deep), can be screwed into trunking outlet US 80 or underfloor outlet box UDL 1-80/R16.1). Visible frame width: 10 mm Ext. diameter: 100 mm Material: polyamide. Standard colours, visible matt surface. iron grey: RAL 7011 grey-beige: RAL 1019 graphite: RAL 9011 Dome lid moisture proofed In accordance with DIN VDE 0634 part 1 as described left. Height above floor: 57 mm. External diameter: 112 mm. Colour: graphite RAL A BA80N/ E BA80N/ F BA80N/9011 SHF 80/30 With rib-reinforced polyamide ring and profile rubber seal E1 SHF80/30/9011 SHF 80/30 M Nirosta version (insulation material covered by Nirosta ring) E2 SHF80/30M/30 /9011 For installation devices to fit flush floor service units and trunking outlets, see Cat. Gr. 78 Installation and connection devices for electrical installation devices. Flush blanking cover moisture proof BABF For flush floor sealing of trunking outlet US80 and underfloor outlet box UDL 1 80/R16. With profile rubber seal. External diameter: 112 mm. Nickel Chrome Old brass Old copper D BABF80NI E BABF80CR F BABF80AM G BABF80AK

45 Underfloor 45 CATALOGUE GROUP 57-GES Round blanking cassette - RKR4 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: RKR7 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: RKR9 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: Round cassette with tube - RKRF4 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: RKFR7 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: RKFR9 - Material: V2A Flooring recess in mm: Material: brass Flooring recess in mm: Part no. Code A RKR4V B RKR4V C RKR4V A RKR4M B RKR4M C RKR4M A RKR7V B RKR7V C RKR7V A RKR7M B RKR7M C RKR7M A RKR9V B RKR9V C RKR9V A RKR9M B RKR9M C RKR9M A RKFR4V B RKFR4V C RKFR4V A RKFR4M B RKFR4M C RKFR4M A RKFR7V B RKFR7V C RKFR7V A RKFR7M B RKFR7M C RKFR7M A RKFR9V B RKFR9V C RKFR9V A RKFR9M B RKFR9M C RKFR9M25 - RK.R Round cassettes Round cassettes for fitting into hollowfloors, raised floors and screed systems. Application Blanking cassette as inspection opening for dry-cleaned and wetmopped floors. Cassette with tube for dry-cleaned and wet-mopped floors. Cassette with cord outlet cap for drycleaned floors. Design Cassette consisting of: Cassette frame with ladders. Four levelling supports for installation depth of E mm. 4 mm sheet steel cover. Cord cap for RKSR version in metal. Tube in RKFR version in polyamide with top cover in V2A or brass. Round cassette minimum total depth (E) Type E RKR 105 mm RKFR 125 mm RKSR 105 mm Fitting dimensions Type RKR 4, RKFR4, RKSR4 RKR7, RKFR7, RKSR7 RKR9, RKFR9, RKSR9 Cut Out ø215 mm ø275 mm ø305 mm Round cassette with cord outlet cap RKSR4 V2A Flooring recess in mm: Brass Flooring recess in mm: RKSR7 V2A Flooring recess in mm: Brass Flooring recess in mm: RKSR9 V2A Flooring recess in mm: Brass Flooring recess in mm: A RKSR4V B RKSR4V C RKSR4V D RKSR4V A RKSR4M B RKSR4M C RKSR4M D RKSR4M A RKSR7V B RKSR7V C RKSR7V D RKSR7V A RKSR7M B RKSR7M C RKSR7M D RKSR7M A RKSR9V B RKSR9V C RKSR9V D RKSR9V A RKSR9M B RKSR9M C RKSR9M D RKSR9M25 Levelling units for other fitting heights (E) mm Code Part no. RKNEV BV mm Code Part no. RKNEV CV Supplied in packs of 4. Tube colours For the colour you want, add: The RAL no to the code The code letter to the part no. Colour RAL code no. Code letter iron-grey 7011 A graphite 9011 F grey-beige 1019 E

46 46 Underfloor CATALOGUE GROUP 57-GES Device installation in underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow/raised floors - Wet-mopped floors Height-adjustable installation unit GRAF9. Application For use in wet-mopped floors for the fitting of installation devices in mounting boxes in accordance with DIN VDE 0634 Part 1. Up to 9 EK-type individual installation devices can be fitted. The number of connection option increases if multiple installation devices are used. Design Device inserts consisting of: Flooring protection frame or support frame, including: Fixing bracket (hollow floor, split pin, raised-floor and screed systems, fixing bracket). Hinged cover (captive in flooring frame, automatic closure) including: Flush floor adjustable or projecting cord outlet with seal. flush floor service unit GRAF 9 As described left, with flooring protection frame, including fittings. Surface polished metal with fine ribbed structure, recesses finished in the following colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Surface natural aluminium, recesses sand-blasted, raised areas polished metal, tube in black or iron-grey only. iron grey RAL 7011 graphite RAL 9011 Turn-lock fastener with automatic cover erection. Cover structured with concentric raised and indented circles. Minimum installation depth for flush floor service unit: 75 mm flush floor service unit GRAF 9 As described left, with flush flooring frame, including fittings. Surface polished metal with fine ribbed structure, recesses finished in the following colours: iron grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Material: Cover and protective frame made of die-cast aluminium, cord cap (tube) made of polyamide. Function and design The distinctive design concentric circles, emphasized by contrasting finish for the recesses means that the timeconsuming process of cutting the flooring into the cover recess is no longer necessary, and makes the unit lighter and easier to handle. Surface natural aluminium, recesses sand-blasted, raised areas polished metal, tube in black or iron-grey only. iron grey RAL 7011 graphite RAL 9011 Ladders GT GRAF9 To accommodate up to 3 GB3 mounting boxes underneath a GRAF9 flush floor service unit. The surface structure reliably prevents damage and scratching the finish, so they can also be used in high visibility areas, such as museums, ticket offices and exhibition centres. The circular form of the device insert is non-directional which means it can be combined with any shape of floor pattern. All the materials used are scratch resistant and resistant to normal detergents and cleaning agents. For device holder cover plates, see page 39. For installation devices, see Cat. Gr. 78 Installation and connection devices for electrical installation systems. Mounting box GB 3 Empty suitable for fitting 3 individual installation devices with holder bracket (EK version) with 2 strain relief mechanisms for incoming and outgoing cables. Dimensions in mm: L = 208, B = 76, D = 39. All flush floor service units are halogen-free.

47 Underfloor 47 CATALOGUE GROUP 57-GES 53 Hollow floor Part no. Code 54 Raised floor Part no. Code Screed system EÜK, OKA, OKU, AIK Part no. Code A2 GRAF9/ E2 GRAF9/ F2 GRAF9/ A1 GRAF9/ E1 GRAF9/ F1 GRAF9/ A GRAF9/ E GRAF9/ F GRAF9/ A2 GRAF9M F2 GRAF9M A1 GRAF9M F1 GRAF9M A GRAF9M F GRAF9M A2 GRAF9/ E2 GRAF9/ F2 GRAF9/ A1 GRAF9/ E1 GRAF9/ F1 GRAF9/ A GRAF9/ E GRAF9/ F GRAF9/ A2 GRAF9M F2 GRAF9M A1 GRAF9M F1 GRAF9M A GRAF9M F GRAF9M E GTGRAF E GTGRAF E GTGRAF A GB A GB A GB3

48 48 Underfloor CATALOGUE GROUP 57-GES Junction box inserts for underfloor systems EÜK (UGD), OKA, OKU, AIK and hollow floors. - Dry cleaned floors Junction box inserts ZES4, 4/10, 6, 6/10, 9 Application Used in dry cleaned floors for blanking of underfloor empty boxes (UGD) and to provide an inspection opening in hollow floors. Design Junction box inserts consist of: Junction box frame, including fixing bracket (hollow floor: split pin screed systems: fixing bracket). Blanking cover made of 4 mm steel plate. Carpet recess: 5 mm, 10 mm for.../10 Junction box inserts only. Junction box inserts / Carpet protection frames and flush floor service units have the same installation diameters and external dimensions. Material: ZES 4, 6 and 9 frame: polyamide. Blanking cover: 4 mm sheet steel. Junction box insert ZES 4 Design as described left. External dimensions in mm: L = W = 217. Installation opening in mm: L = W = 201. iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 7011 ZES 4/10 Design as described left. External dimensions in mm: L = W = 220. Installation opening in mm: L = W = 201. iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Junction box insert ZES 6 Design as described left. External dimensions in mm: L = 270, W = 214. Installation opening in mm: L = 253, W = 200. iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 7011 ZES 6/10 Design as described left. External dimensions in mm: L = 276, W = 220. Installation opening in mm: L = 253, W = 200. iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Junction box insert Carpet recess 5 mm ZES.. Flooring mm Steel cover Levelling plate Junction box frame Carpet recess 10 mm ZES../ ZES 9 Design as described left. External dimensions in mm: L = W = 263 Installation opening in mm: L = W = 243 iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011

49 Underfloor 49 CATALOGUE GROUP 57-GES 53 Hollow floor Part no. Code 54 Raised floor Part no. Code Screed system EÜK, OKA, OKU, AIK Part no. Code A ZES4/ E ZES4/ F ZES4/ A ZES4/10/ E ZES4/10/ F ZES4/10/ A ZES6/ E ZES6/ F ZES6/ A ZES6/10/ E ZES6/10/ F ZES6/10/ A2 ZHB9/ E2 ZHB9/ F2 ZHB9/ A ZHB9/ E ZHB9/ F ZHB9/9011

50 50 Underfloor CATALOGUE GROUP 57-GES Junction box inserts for underfloor systems Eük (UGD), OKA, OKU, AIK and hollow floors - Dry cleaned floors Junction box inserts ZESR4, R7, R9 Application Use in dry cleaned floors for blanking underfloor empty boxes (UGD) and to provide an inspection opening in hollow floors. Junction box insert ZESR 4 External diameter in mm: ø228 Installation opening diameter in mm: ø215 iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Design Junction box inserts consist of: Junction box frame, including fixing bracket (hollow floor: split pin screed systems: fixing bracket). Blanking cover made of 4 mm steel plate. Carpet recess: 5 mm, 10 mm for... /10 Junction box inserts only. Junction box inserts and flush floor service units have the same installation diameters and external dimensions. Material: ZES R4, R6 and R9 junction box frame: polyamide. Blanking cover: 4 mm sheet steel. ZESRA7: die-cast aluminium. Junction box insert ZESR 7 External diameter in mm: ø295 Installation opening diameter in mm: ø275 ZESR 7A External diameter in mm: ø295 Installation opening diameter in mm: ø275 iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011 Carpet recess 5 mm Flooring Carpet recess 10 mm Junction box insert ZESR 79 External diameter in mm: ø325 Installation opening diameter in mm: ø305 ZES mm Steel cover Levelling plate Junction box frame ZES../ iron-grey RAL 7011 grey-beige RAL 1019 graphite RAL 9011

51 Underfloor 51 CATALOGUE GROUP 57-GES 53 Hollow floor Part no. Code 54 Raised floor Part no. Code Screed system EÜK, OKA, OKU, AIK Part no. Code A2 ZRHB4/ E2 ZRHB4/ F2 ZRHB4/ A ZESR4/ E ZESR4/ F ZESR4/ A2 ZRHB7/10/ E2 ZRHB7/10/ F2 ZRHB7/10/ A ZESR7/10/ E ZESR7/10/ F ZESR7/10/ A2 ZRHB7/ A ZESRA7/ A2 ZRHB9/ E2 ZRHB9/ F2 ZRHB9/ A ZESR9/ E ZESR9/ F ZESR9/9011

52 52 Underfloor CATALOGUE GROUP 57-GES System 55 The underfloor system 55 enables electrical and data equipment to be fitted in floors with screed depths of 55 mm and above. Based on a flush floor service unit with a fixed height of 55 mm power socket outlets and data connection units which have been optimised to suit this application. The size of the flush floor service unit is sufficient to supply one or two office workplaces. Flush floor service unit for System 55 The flush floor service units have a metal device holder which is pre-fitted in the factory and into which the installation devices can be fitted directly. Installation devices Ackermann power socket outlets are mounted horizontally. They have their own strain-relief mechanism and a 105º angle of entry. Because of the restricted space, only connection cables with angled plugs can be used. Data connection sockets Because of the installation space available, only the connection sockets provided can be used: UAE, TAE and WAEG-U and WAEG6C-U connection units. Cable guidance The opening, flush floor trunking system OKA2 with nominal height of 40 mm + 30 mm levelling range is suitable for cable guidance. To keep the cable guidance area as small as possible, extension units that can be fitted on the side are also available (on request).

53 Underfloor 53 CATALOGUE GROUP 57-GES Flush floor service unit GES 6/55L Design as described right, including six fixing brackets. Minimum installation height for device insert: 55 mm. Carpet recess: 5 mm. Dimensions: g1 = 214 mm, g2 = 270 mm. Installation opening: 253 mm x 200 mm. Part no. Code * GES6/55L..* Flush floor service unit GES 9/55 Design as described right, including six fixing brackets. Minimum installation height for device insert: 55 mm. Carpet recess:: 5 mm. Dimensions: g = 263 mm. Installation opening: 243 mm x 243 mm * GES9/55..* Flush floor service unit GESR 9/55 Design as described right, including eight fixing brackets. Minimum installation height for device insert: 55 mm. Carpet recess:: 5 mm. Dimensions: dg = ø325 mm. Installation opening diameter: ø305 mm * GESR9/55..* Device holder GES/T5 With cover plate for fitting a single installation device with holder bracket (EK version) With strain relief mechanism. Device installation depth can be adjusted from 19.5 mm to 31.5 mm in 2 mm increments. Perforated cover plate: diameter ø45 mm F GES/T5 Flush floor service units for screed depth of 55 mm and higher For installation in OKA 2 flush floor trunking systems. Application The flush floor service unit consists of: Carpet protection frame including assembly frame to hold power sockets, device holders, WAEG6-U connection unit and fitting inserts. Hinged cover, captive carpet protection frame, automatic closure, includes: Load plate made of 4 mm sheet steel, pre-galvanised. Cord cap with foam seal. Adjustable holder handle to open the cover. Flush floor service unit and device holders are halogen-free. * For the colour you want, add: - the RAL colour code to the code - the letter code to the part no. Colour RAL colour code Letter code iron grey 7011 A grey-beige 1019 E graphite 9011 F Configuration plan for flush floor service unit GES 6/55L 2fach Schuko Pos. C H = 19,5-31,5 Pos. C H = 19,5-31,5 2fach Schuko 2fach Schuko H = 19,5-27,5 Pos. Pos. A Schnurauslassrichtung H = 19,5-27,5 H = 19,5-27,5 Pos. A Pos. B Schnurauslassrichtung H = 19,5-27,5 Pos. A H = 19,5-27,5 Configuration plan for flush floor service unit GE 9/55, GESR 9/55 Possible configurations Variant 2 gang power socket WAEG-U/WAEG6C-U Device holder Fitting insert GES 6/66L in pos. B + C 1 in pos A in pos A 1 in pos. B + C GES 9/55, GESR 9/ or 2 1 in pos B + C 2 in pos A + B + C or 2-2 in pos A or 2-2 in pos A 2 in pos B + C Dimensions of device holder Bottom edge of installation unit to Bottom edge of installation unit to Connection sockets that can be fitted bottom edge of holder bracket bottom edge of cover TAE UAE 20 SQ in pos A and B mm 46 mm x x x in pos C mm 46 mm x x x

54 54 Hanging Services Modules CATALOGUE GROUP 63-VH - VH Hanging service modules pre-wired or empty Housing made of high-impact resistant polyamide, suitable for 4 or 8 installation devices (max. installation depth 48 mm) with holder ring or bracket (60 or 67 mm fixing center) and for devices with flangefitting, e.g. CEE industrial plug connector (fixing center 60 x 60 mm or 70 x 70 mm). Each installation device is covered with a separate cover plate so it can be fitted or removed individually. Legend: 1 Housing 2 Base 3 Top piece 4 Installation device 5 Cover plate 1 3 There is a perforated insulation wall to separate devices with different voltage ratings or circuits from one another. Power is supplied through cable bushes* (with strain-relief clips for cables with a diameter of up to 14 mm) next to the suspension shackle in the housing. 5 Colour combination yellow/black in accordance with VBG 125, safety labelling in the workplace. CEE LE 16A Suspension is as follows: - Service modules for electrical connections only, using a knotted link chain. This is suspended in the shackle placed in the suspension shackle of the housing. - Service modules for electrical and compressed air connections, using an air conduit connected to a suspension shackle and a tension spring. The compressed air conduit is fed into the housing. VH 4 Housing dimensions Height: 162 mm Width: 140 mm Depth: 140 mm The VHF8 Service module is specially designed to be used in damp and wet areas, e.g. workshops, laboratory environments, large-scale kitchens, bakeries, slaughterhouses, etc. The installation of protective devices can secure workplaces in accordance with DIN VDE 0100 part 737. The module and the installation devices available (see Cat. Gr. 78 Installation and connection devices for electrical installation systems) offer a degree of protection of IP 44 (splash-proof). * Cable bushes must not be used as blanking stops. Cable blind plugs or twist nipples with M20 thread in accordance with DIN EN should be used for this purpose. These must be fixed with a hex head nut. 252 mm 327 mm

55 Hanging Services Modules 55 CATALOGUE GROUP 63-VH Hanging Service Module Part no. Code VH-4 Hanging service module for electrical connections VH 4/00 Consisting of: Housing in black (RAL 9011), with partition wall. Suspension shackle and holder hook. no cover plates. Weight: approx kg/unit. VH 4/N6 housing As VH 4/00, but with 4 cover plates* and fitted with 2 3-pin terminals and 4 x single schuko sockets 16A/250 V, pre-wired on 2x AC current circuits. Weight: approx kg/unit. VH 4/N8 housing As VH 4/N6, but fitted with: 1 3-pin terminal and 3 x single schuko sockets 16 A/ 250 V, pre-wired on 1 alternating current circuit A/415 V CEE socket Weight: approx kg/unit A0 VH4/ B1 VH4/N B3 VH4/N8 Fitting note Service modules must only be used with flexible cables. * Cover plates: Material: polyamide. Colour: rape yellow RAL Hanging Service Module VH 4 L/00 Consisting of: Housing in black (RAL 9011); with partition wall and 1m x 1 / 2 conduit with connection for compressed air hose (13 x 3.5) mm and 2-way distributor 1 / 2. Suspension shackle and support hook. no cover plates. Weight, approx 2.59 kg/unit. VN 4 L/N8 housing As VH 4 L/0, but with 4 cover plates* and fitted with: 1 3-pin terminal and 3 x single schuko sockets 16A/250 V, pre-wired on a single AC circuit; 1 16A/415V CEE socket Weight: approx kg/unit. Hanging Service Module VHF 8/00 Consisting of: Housing in black (RAL 9011) with partition wall. Suspension shackle and support hook; no cover plates. To hold up to 8 installation devices, specifically designed for use in damp and wet areas. Degree of protection: IP 44 Weight: approx kg/unit. Hanging Service Module A0 VH4L/ B3 VH4L/N A VHF8/00 VH 4 L Hanging service modules for electrical and compressed air connections Fitting note Service modules must only be used with flexible cables. * Cover plates: Material: polyamide. Colour: rape yellow RAL VHF 8 Hanging service modules electrical connections, specially designed for damp and wet areas Fitting note Service modules must only be used with flexible cables. VHF 8 L/00 As VHF 8/00 with 1m x 1 / 2 conduit for connection to air hose. 13 x 3.5 mm and 2-way distributor 1 / 2. Degree of protection: IP 44 Weight: approx kg/unit A VHF8L/00 VHF 8L 0 Hanging service modules for electrical and compressed air connections, specially designed for damp and wet areas

56 56 Hanging Services Modules CATALOGUE GROUP 63-VH Accessories for VH 4 Cover plates made of polyamide in rape yellow RAL * Not suitable for installation devices with a round central insert in accordance with DIN For installation devices for fitting in VH supply units, see Cat. Gr. 78 Installation and connection devices for electrical installation systems. Important: Cover plates with square or rectangular fitting openings are only suitable for fitting an Ackermann power socket. Snap the sockets into the cover plate before connecting. Cover plate VH 4 P01 Blanking, for special equipment on-site. Cover plate VH 4 P9 With 63.5 mm diameter hole for CEE 16/32 A socket, includes 4 fixing screws, Cover plate VH4 P10 With 45 mm diameter hole for installation devices with carrier handle or carrier ring. Part no. Code EW VH4P CW VH4P AW VH4P10 Cover plate VH 4 P7 For single Ackermann power socket. Cover plate VH 4 P8 For 2 gang Ackermann power socket DW VH4P BW VH4P8... Additional partition wall VH 4 TW For insulation of three different current types or circuits. Material: plastic moulding compound A VH4TW Accessories for VH 4 and VHF 8 Tension spring Made of spring steel with 2.8 mm diameter L0 = 200 mm. Ln = 500 mm at Fmax. Weight: approx. 0.3 kg/unit. for VH 4L/ with Fmax = 80 N. for VH 8L/ with Fmax = 100 N VHF VHF100 Knotted-link chain Made of steel, pre-copper-plated and nickelplated in accordance with DIN Max. tensile force: 800 N. (Please specify chain length required). Weight, approx kg/m VHGK Accessories for VHF 8 Hinged cover and mounting bracket 4 modules For protective devices, such as MCB, rcd, RCBO etc. Use cover plate VHF8P6 (34952F) A VHF/A Holders - VHF/T2 - With N and 4 x 10 mm 2 PE terminal strip (needed to fit a cable protection switch). VHF/T1 With 4 x 10 mm 2 PE terminal strip (needed to fit an FI protective switch) B VHF/T A VHF/T1

57 Hanging Services Modules 57 CATALOGUE GROUP 63-VH Cover plate VHF 8 P0 Blanking plate. Part no. Code G VHF8P0 Accessories for VHF 8 Cover plates for VHF8 made of plastic moulding compound in rape yellow RAL For installation devices to fit into VH.. supply units, see Cat. Gr. 78 Installation and connection devices for electrical installation systems. Cover plate VHF 8 P1 With 2 x 45 mm diameter hole for 2 power sockets (same circuit) with hinged cover (901 F) A VHF8P1 Cover plate VHF 8 P2 With 45 mm diameter hole for power socket with hinged cover (901 F) and 60 mm diameter hole for 16/32 A CEE socket (sockets on same circuit), includes 4 fixing screws B VHF8P2 Cover plate VHF 8 P3 With 45 mm diameter hole for for power socket with hinged cover (901 F) E VHF8P3 Cover plate VHF 8 P4 With 63.5 mm diameter hole for 16/32 A CEE socket, includes 4 fixing screws C VHF8P4 Cover plate VHF 8 P6 With rectangular hole for fitting protective devices (4 modules). Use with hinged cover VHF/A (34953A) F VHF8P6 Additional partition wall VHF 8 TW Material: plastic moulding compound F VHF8TW Additional insulating wall VHF 8 LTW To provide 3 segregated compartments in combination with an air connection. Material: plastic moulding compound G VHF8LTW

58 58 Service Posts and Poles CATALOGUE GROUP 66-ISS ISS Service posts and poles Part no. Code Technical specifications for ISS HS2 Service posts made of aluminium for flush surface fitting of S99 installation devices on two opposite sides. Post body and cover: extruded aluminium profile, either anodised in natural colour or painted. 170 Service post ISS HS2 No equipment fitted, for direct mounting on the floor, with pre-cut cover segments in order to fit installation devices on two sides. Versions: Post, side profiles and covers anodised, top end plate painted in graphite RAL Post and covers anodised, side profiles and top end plate painted in graphite RAL ISSH A1 D120A1 ISSHS A1 D120A1/9011 Head plate: sheet steel, finished in graphite. Post cover: With 2 x 3 pre-cut segments to be replaced directly with installation trunking box which snap in at the front to fit S99 installation devices and finished S99 socket units Post and covers finished in: pure white RAL 9010 light grey RAL 7035 graphite RAL 9011 ISSHS AK D120A1/ AM D120A1/ AA D120A1/9011 Dimensions: Height: 680 mm Base area = 120 x 120 mm. Fixing: Internal floor-mounting. On request: Other heights, other colour combinations. ISS 120 Service pole body and cover: either anodised in natural colour or painted. Top and bottom end plates: Die-cast zinc Finished in RAL 9011 graphite if the column is anodised in natural colour. If the column is painted, in the same colour as the column. Dimension: Room height is the same as the column height, the column has adjustment tolerance of 35 / + 65 mm. Column cover: With 4 pre-cut segments to be replaced directly with installation trunking box which snap in at the front to fit S99 installation devices and finished S99 socket units. * for the painted version, please replace: - the 1 in the part number by the code letter - the A in the code with / and the RAL colour number. Colour RAL colour no. Code letter graphite 9011 A cream white 9001 B pure white 9010 K light grey 7035 M For installation devices that fit, see Cat. Gr Ceiling 370 Approx Finished Floor Service pole ISS 120 Service pole room height for surface-flush fitting of S 99 installation units. With pre-cut pole covers. The narrow side of the column has an external fitting groove on both sides in order to fit a coloured decorative strip. Service pole body includes C-rail to fit a divider. Room height: 2450 mm 2550 mm 2650 mm 2700 mm 2750 mm 2850 mm 2950 mm 3050 mm 3150 mm 3250 mm 3300 mm 3350 mm 3450 mm 3550 mm 3650 mm 3700 mm Decorative Strip BP For additional colour coding of the service pole ISS 120. Material: plastic moulding compound. Black similar to RAL 9005 Grey similar to RAL 7046 Red similar to RAL 3013 Green similar to RAL 6016 Black similar to RAL 9005 Grey similar to RAL 7046 Red similar to RAL 3013 Green similar to RAL F1* ISS120/245A* G1* ISS120/255A* H1* ISS120/265A* J1* ISS120/270A* K1* ISS120/275A* L1* ISS120/285A* M1* ISS120/295A* A1* ISS120/305A* B1* ISS120/315A* C1* ISS120/325A* D1* ISS120/330A* E1* ISS120/335A* F1* ISS120/345A* G1* ISS120/355A* H1* ISS120/365A* J1* ISS120/370A* AA BP3SW BA BP3GR CA BP3RT DA BP3GN AB BP4SW BB BP4GR CB BP4RT DB BP4GN

59 Service Posts and Poles 59 CATALOGUE GROUP 66-ISS ,5 47,5 Front snap-in installation trunking box for service posts and poles ISS HS2 and ISS 120 With hinged bottom section with 2 openings for NYM cables. Closing the box fixes the cables in place. Further openings in the side walls and base plate. Material: polyamide, black, flame-proof in accordance with DIN VDE 0471 part 1 Filament test 750ºC. 71 GD 1 1 gang For fitting 1 installation device. Dimensions in mm: W = 71, T = 42.5 Supplied in packs of GD 3 2 gang For fitting 2 individual installation devices or one multiple power socket, includes partition wall for the fitting of installation devices for different current types. Dimensions in mm: W = 150, D = Supplied in packs of 2. Strain relief mechanism 7 ZE Snap fits onto openings of installation trunking box. Cable clamping range: up to 14 mm. Material: polyamide. Supplied in packs of 50. Part no. Code MV 71GD PV 71GD V 7ZE Accessories for service posts and poles ISS HS2 and ISS H Front snap-in cover plates S90-AF 19 single To cover one installation device with a 50 mm central plate. Dimensions in mm: W = 86, H = A..* S99-AF18/* W S90-AF x single To cover two installation devices with a 50 mm central plate. Dimensions in mm: W = 170, H = B...* S99-AF28/* 50 W Ceiling duct ISS120DDF - Component to fix an installation pole ISS 120 to rooms with a suspended ceiling. To be adjusted on-site to the height required (distance from suspended ceiling to real ceiling). Cover blind pure white, RAL Length: 300 mm Length: 500 mm Length: 1000 mm ISS120DDF A 300RW B 500RW C 1000RW Earth conductor clamp 8AWR For use in the post / pole and cover. Material: sheet steel, galvanised. Supplied in packs of 10. Danger! Metallic components are still live in the event of a fault. Screw the contact screw up to at least 1.2 Nm CV 8AWE L oben Divider 61 TW/ISS 120 For vertical separation of service pole ISS120. Standard length supplied: 2000 mm. Material: 1 mm sheet steel, pre-galvanised. Cable retainer 7 KL 80 A Stabilises partition wall and holds cables in position A 6TW/ISS C 7KL80A

60 60 Service Posts and Poles CATALOGUE GROUP 66-ISS ISS Service poles Sheet steel Technical specifications for ISS 98 Service pole body made of galvanised sheet steel, surface silk-matt powder coating, with C rail. Divider piece 2000 mm. Covers have a total length of 2500 mm. Material and surface finish as service pole. Top end with adjustable telescopic fixing assembly 40 x 40 mm, to connect to the ceiling. Base with tension screw The standard length supplied is suitable for the following height range: min 2800 mm to max 3700 mm. Max Min.1200, Max.2100 Min.2800, Max.3700 Service pole - ISS 98 and ISS For fitting installation devices. Size: 98 x 63.5 x 2500 mm. Size: 133 x 63.5 x 2500 mm. Standard length supplied: 2500 mm. Standard colour: pure white RAL Weight: approx or 14.6 kg/unit. 63, ,5 133 Part no. Code AK ISS98/OT3/ AK ISS133/OT3/ Fixing clamp ISS 98 KF To fix the telescopic profile of the service post ISS98 or ISS 133 to the carrier rails on intermediate or suspended ceilings, cableways or other support systems. Material: pre-galvanised sheet steel. Weight: approx kg/unit B ISS98KF Cover plate ISS 98 B to cover the ceiling panel cut-outs next to where the telescopic profile of the service post ISS 98 or ISS 133 cuts through the ceiling (for suspended ceilings only!). Dimensions: 110 x 110 x 4 mm. Material: white plastic. Weight: approx kg/unit B ISS98B Technical specifications for ISS HS4 Service post made of sheet steel for fitting installation devices on four sides. The base protective frame to provide mechanical protection to the service post around the base is available as an optional accessory. Post body and cover: sheet steel, painted. 680 Service post ISS HS4 Made of sheet steel, for direct mounting to the floor, with four sections to fit installation devices on four sides. Column painted in the following colours: pure white RAL 9010 light grey RAL 7035 graphite RAL 9011 ISSHS4/61OT3/ AK 690/ AM 690/ AA 690/9011 Head plate: painted in graphite. Base protection frame: optional, sheet steel, painted in graphite RAL Dimensions: Height = 680 mm. Base area: 201 x 201 mm. Fitting: internal floor-mounting. On request: other heights and other colours. Base Protective frame ISS HS4 SR - For mechanical protection of the base of the service post. Material: 1.4 mm sheet steel, painted in graphite RAL AA ISSHS4SR40/9011 Device installation For S 990 cover plates and pre-assembled socket units for ISS 98 and ISS HS4, see pages 70 and 71. L Divider 61 TW - For vertical internal separation of the ISS HS4 service pole. Self-conductive contacting. Standard length supplied: 2000 mm. Material: 1 mm sheet steel: pre-galvanised A 61TW

61 Wall Trunking Systems 61 CATALOGUE GROUP 70-WIK Benefits of the wall trunking systems with 80 system opening Installation benefits Front snap-in installation trunking boxes Better utilisation of the space inside the trunking. Simple connection of the installation devices from hinged bottom sections of installation box. Divider Automatic earthing continuity. - WIK 3 Trunking systems for walls With extensive additional equipment for flexible applications in new buildings and the referbishment of old buildings. Benefits of trunking systems made of sheet steel and aluminium Pre-puched fixing holes in bottom sections of trunking for rapid fitting to consoles. Lids with integral earthing clips earth continuity at no additional cost (for sheet steel). Clip-in divider with automatic earth continuity, made of sheet steel consistent protective measure at no additional cost. Installation boxes snap in at the front without using tools saving time and making cable installation easier. Front snap-in S-990 covers to ensure no interruption during subsequent installations. Pre-punched fixing holes Simple, time-saving console fitting. 80 trunking cover No covers with holes required. Self-contacting thanks to earthing clips (only applies to sheet steel trunking systems). Device installation options in trunking with 80 system opening for Area programmes from external manufacturers. Te li ko S-990 cover plates (see pages 70 and 71). Earth continuity for sheet steel wall trunking systems Trunking Base Trunking Lid Trunking Divider In accordance with DIN EN Trunking couplings Fixing / earthing clip Self continuity Earth continuity for aluminium wall trunking systems Trunking Base Trunking Lid Trunking Divider Trunking couplings Earth conductor clamp Self continuity

62 62 Wall Trunking Systems CATALOGUE GROUP 70-WIK - 61 WIK 3 Trunking system made of sheet steel, galvanised or powder coated, with 80 system opening Trunking design Galvanised or galvanised and powder coated, supplied according to the individual part number. Material Trunking base and formed sections: 1 mm sheet steel, pre-galvanised and shaped 1. Lids Sheet steel 61 OT3 with fixing clips for mechanical and electrical connection to the bottom section of the trunking. Plastic 71 OT3 PVCu, with grooved surface 2 in 3 standard colours, RAL 9001, 9010 and Lid External corner cover Material Short code 61OT3..* Short code 61AO3..* smooth sheet steel 1 Part no A..* Part no A..* Material Short code 71OT3K..* Short code 71AO3K..* Grooved plastic 2 Part no A* Part no A* Standard delivery Length of trunking base sections and covers: 2000 mm. standard colours (see colour table to right). On request Different lengths of trunking base sections and covers, up to 3000 mm, other trunking depths (e.g. 80 mm), other colours, cutting block. Accessories See page 70 and following. Notes Painted visible surfaces protective film-covered. Unpainted trunking for on-site coating only. 1) DIN EN 10142: Surface smooth. 2) Visible surface ribbed Trunking base section Coupling External corner base section Short code 61UT3/98* Short code 6KU65 Short code 61AE3/98 Part no A* part no A Part no A* Short code 61UTA3/98100/* Short code 6KU100 Short code 61AE3/98100/* Part no C* part no A Part no C* Short code 61UT3/98100/* Short code 6KU65 Short code 61AE3/133/* Part no A* part no A Part no A* Short code 61UTA3/133100/* Short code 6KU100 Short code 61AE3/133100/ Part no C* part no A Part no C* Short code 61UTA3/1731/* Short code 6KU65 Short code 61AE3/173 Part no A* part no A Part no A* Short code 61UTA3/173100/* Short code 6KU100 Short code 61AE3/173100/ Part no C* part no A Part no C* Short code 61UTA3/213/* Short code 6KU65 Short code 61AE3/213 Part no A* part no A Part no A* Short code 61UTA3/213100/* Short code 6KU100 Short code 61AE3/ Part no C* part no A Part no C*

63 Wall Trunking Systems 63 CATALOGUE GROUP 70-WIK 70W Flat angle cover Touch-up stick 70 WZ 3 Cutting block Suction lifter WZ 1059 Short code 61FO3..* Short code 70WZ3/..* Short code on request Short code WZ1059 Part no A..* Part no * Part no. on request Part no E Short code Part no. 71FO3K..* A To repair minor damage to paintwork. To reinforce the trunking base sections when lengths are adjusted on-site. To open trunking systems with smooth trunking covers. * Standard colours for painted sheet steel covers, bottom sections and plastic covers. Visible external surfaces mattpowder coated, plastic covers dyed. For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M The T-branch base section is covered with a consistent trunking cover. For nominal depth 63.5 D = 40 mm. For nominal depth 100 D = 60 mm. Flat angle base section - Down Flat angle base section - Up Internal corner base section T-branch base section End cap Short code 61FU3/98..* Short code 61FO3/98..* Short code 61IEV3/98..* Short code 61TS3/98..* Short code 61ES3/98..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FU3/98100* Short code 61FO3/98100* Short code 61IEV3/98100* Short code 61TS3/98100* Short code 61ES3/98100* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..* Short code 61FU3/133..* Short code 61FO3/133..* Short code 61IEV3/133..* Short code 61TS3/133..* Short code 61ES3/133..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FU3/133100* Short code 61FO3/133100* Short code 61IEV3/133100* Short code 61TS3/133100* Short code 61ES3/133100* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..* Short code 61FU3/173..* Short code 61FO3/173..* Short code 61IEV3/173..* Short code 61TS3/173..* Short code 61ES3/173..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FU3/173100* Short code 61FO3/173100* Short code 61IEV3/173100* Short code 61TS3/173100* Short code 61ES3/173100* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..* Short code 61FU3/213..* Short code 61FO3/213..* Short code 61IEV3/213..* Short code 61TS3/213..* Short code 61ES3/213..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FU3/213100* Short code 61FO3/213100* Short code 61IEV3/213100* Short code 61TS3/213100* Short code 61ES3/213100* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..*

64 64 Wall Trunking Systems CATALOGUE GROUP 70-WIK - 61 WIKD 3, 6 WIKP 3 Sheet steel trunking system, galvanised or powder coated, with 2 system openings 80/50 or 80/80 or with 80 system opening trunking design Galvanised or galvanised and powder coated, supplied according to the individual part number. 61 WIKD 3 in painted version only! Material Trunking base and formed sections: 1 mm sheet steel, pre-galvanised and shaped 1. Lids Sheet steel 61 OT3 with rest clips for mechanical and electrical connection to the bottom section of the trunking. Plastic 71 OT3 PVCu, with grooved surface 2 in 3 standard colours, RAL 9001, 9010 and Standard delivery Length of trunking base sections and covers: 2000 mm standard colours (see colour table to right). On request Different lengths of trunking base sections and covers, up to 3000 mm, other trunking depths (e.g. 80 mm), other colours, sawed cores. Accessories See page 70 and following. Notes Painted visible surfaces protective film-covered. Unpainted trunking for on-site coating only. 1) DIN EN 10142: Surface smooth. 2) Visible surface ribbed. Lid External corner cover Material: Short code 61OT3..* Short code 61AO3..* smooth sheet 1 Part no A..* Part no A..* steel w = 80 mm Material: Short code 71OT3K..* Short code 71AO3K..* Grooved 2 Part no A* Part no A* plastic Material: Short code 61OT3/50..* Short code 61AO3/50..* smooth sheet 1 Part no A..* Part no A..* steel w = 50 mm Trunking Base section coupling External corner base section Short code 61UTD3/173* Short code 6KU65 Short code 61AED3/173* Part no A* part no A Part no A* Sales unit 2 units Short code 61UTD3/173/1/* Short code 6KU100 Short code 61AED3/173/1/* Part no C* part no A Part no C* Sales unit 2 units 213 D Short code 61UTD3/213* Short code 6KU65 Short code 61AED3/213* Part no A* part no A Part no A* Sales unit 2 units Short code 61UTD3/213/1/* Short code 6KU100 Short code 61AED3/213/1/* Part no C* part no A Part no C* Sales unit 2 units Trunking base section coupling External corner base section Short code 61UTP3/110133* Short code 6KUP133 Short code 61AEP3/110133* Part no A* part no A Part no A* External corner cover Short code Part no. 61AOP/3..* A

65 Wall Trunking Systems 65 CATALOGUE GROUP 70-WIK 70W Flat angle cover Touch-up stick 70 WZ 3 Cutting Block Suction lifter WZ 1059 Short code 61FO3..* Short code 70WZ3/..* Short code on request Short code WZ1059 Part no A..* Part no * Part no. on request Part no E Short code Part no. 71FO3K..* A To repair minor damage to paintwork. To reinforce the trunking base sections when lengths are adjusted on-site. To open trunking systems with smooth trunking covers. * Standard colours for painted sheet steel covers, base sections and plastic covers. Visible external surfaces mattpowder coated, plastic covers dyed. For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M Short code Part no. 61FO3/50..* A...* The T-branch base section is covered with a consistent trunking cover. For nominal depth 63.5 D = 40 mm. For nominal depth 100 D = 60 mm. Flat angle base section - Down Flat angle base section - Up Internal corner base section T-branch base section End cap Short code 61FUD3/173..* Short code 61FOD3/173..* Short code 61IEDV3/173..* Short code 61TSD3/173..* Short code 61ES2/173..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FUD3/173/1* Short code 61FOD3/173/1* Short code 61IEDV3/173/1* Short code 61TSD3/173/1* Short code 61ES2/173/1* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..* Short code 61FUD3/213..* Short code 61FOD3/213/..* Short code 61IEDV3/213..* Short code 61TSD3/213..* Short code 61ES2/213..* Part no A..* Part no A..* Part no A..* Part no A..* Part no A..* Short code 61FUD3/213/1* Short code 61FOD3/213/1* Short code 61IEDV3/213/1* Short code 61TSD3/213/1* Short code 61ES2/213/1* Part no C..* Part no C..* Part no C..* Part no C..* Part no C..* Flat angle base section - Down Flat angle base section - Up Internal corner base section End cap left End cap right Short code 61FWUP3/110133* Short code 61FWOP3/110133* Short code 61IEP3/110133* Short code 61EP2L100133* Short code 61EP2r100133* Part no A..* Part no A..* Part no A..* Part no B Part no A Flat angle cover Flat angle cover Internal corner cover Short code 61FUOP3..* Short code 61FOOP3..* Short code 611OP3..* Part no B Part no A Part no a

66 66 Wall Trunking Systems CATALOGUE GROUP 70-WIK - 81 WIK 3 Aluminium trunking system, anodised or powder coated, with 80 system opening trunking design Anodised or powder coated, supplied according to the individual part number. Material Trunking base section: Sheet steel back wall with aluminium profiles fitted at the factory. With pre-punched fixing holes for wall and console mounting. Lid External corner cover Material: Short code 81OT3..* Short code 81AO3A..* smooth Part no A1..* Part no A1 aluminium Lids Self-locking lid profile made of aluminium. Standard delivery Length of trunking base sections and covers: 2000 mm. standard colours (see colour table to right). On request Un-finished version, other colours, lengths of up to 6 mm, cutting block. Accessories See page 70 and following. 1) Al MG Si 0.5 EQ anodised in natural colour. Notes Anodised aluminium trunking can exhibit slight colour difference because of material and process-related light scattering (in accordance with DIN 17611). Important: Trunking systems must always be fitted with 7 KL 80 cable retainer (page 72) (2 per metre) Trunking base section Coupling External corner base section Short code 81UT3/98A* Short code 8KU65 Short code 81AE3/98A* Part no A1* part no A Part no A1* Short code 81UT3/133A* Short code 8KU65 Short code 81AE3/133A* Part no A1* part no A Part no A1* Short code 81UT3/173A* Short code 8KU65 Short code 81AE3/173A* Part no A1* part no A Part no A1* 213D 100 Short code 81UT3/213/1A* Short code 8KU100 Short code 81AE3/213/1A* Part no A1* part no B Part no A1*

67 Wall Trunking Systems 67 CATALOGUE GROUP 70-WIK 70W Flat angle cover Touch-up stick 70 WZ 3 Cutting Block Suction lifter WZ 1059 Short code 81FO3A* Short code 70WZ3/..* Short code on request Short code WZ1059 Part no A1 Part no * Part no. on request Part no E To repair minor damage to paintwork. To reinforce the trunking base sections when lengths are adjusted on-site. To open trunking systems with smooth trunking covers. * Standard colours for painted sheet steel covers, base sections and plastic covers. Visible external surfaces mattpowder coated, plastic covers dyed. For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M The T-branch base section is provided without lids, use trunking lids. For nominal depth 63.5 D = 40 mm. For nominal depth 100 D = 60 mm. Flat angle base section - Down Flat angle base section - Up Internal corner base section T-branch base section End cap Short code 81FWU3/98A* Short code 81FWO3/98A* Short code 81IE3/98A Short code 8ITS3/98A* Short code 81ES2/98A..* Part no A1* Part no A1* Part no A1..* Part no A1..* Part no A1* Short code 81FWU3/133A* Short code 81FWO3/133A* Short code 81IE3/133A Short code 8ITS3133A* Short code 81ES2/133A..* Part no A1* Part no A1* Part no A1..* Part no A1..* Part no B1* Short code 81FWU3/173A* Short code 81FWO3/173A* Short code 81IE3/173A Short code 8ITSA3/173A* Short code 81ES2/173A..* Part no A1* Part no A1* Part no A1..* Part no A1..* Part no C1* Short code 81FUD3/213/1A* Short code 81FOD3/213/1A* Short code 81IED3/213/1A Short code 8ITSD3/213/1A* Short code 81ES2/213/1A..* Part no A1* Part no A1* Part no A1..* Part no A1..* Part no D1*

68 68 Wall Trunking Systems CATALOGUE GROUP 70-WIK - 71 WIK PVCu wall trunking with 80 system opening Standard lengths Trunking base and cover sections 2000 mm. Trunking design Trunking base sections with grid holes. Self-locking trunking cover. Materials Trunking, covers and form sections made of PVC. Trunking coupling Trunking divider piece Short code 71KU70 Short code 71TW70 part no A Part no A Sales unit 10 units Sales unit 2 m Standard delivery and what is supplied: Trunking base sections with two couplings: Internal corner, external corner and flat angle come with cover. Standard colours RAL 9010 pure white. RAL 9001 cream white. RAL 7035 light grey. Accessories: See page 70 and following. *Standard colours For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M Trunking base section Lid Cable retainer Short code 71UT100/* Short code 71OT3/* Short code 71KL76 Part no A..* Part no A..* Part no A Sales unit 2 m Sales unit 2 m Sales unit 10 units Short code 71UT130/* Short code 71OT3/* Short code 71KL76 Part no A..* Part no A..* Part no A Sales unit 2 m Sales unit 2 m Sales unit 10 units Short code 71UT170/* Short code 71OT3/* Short code 71KL76 Part no A..* Part no A..* Part no A Sales unit 2 m Sales unit 2 m Sales unit 10 units 210D 70 Short code 71UT210/* Short code 71OT3/* Short code 71KL76 Part no A..* Part no A..* Part no A Sales unit 2 m Sales unit 2 m Sales unit 10 units

69 Wall Trunking Systems 69 CATALOGUE GROUP 70-WIK External corner Flat angle Internal corner T-branch End cap Short code 71AE100/ Short code 71FW100/ Short code 71IE100/ Short code 71TS100/ Short code 71ES100/ Part no A Part no A Part no A Part no A Part no A Length 130 mm Length 100 mm Length 130 mm Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Short code 71AE130/ Short code 71FW130/ Short code 71IE130/ Short code 71TS130/ Short code 71ES130/ Part no A Part no A Part no A Part no A Part no A Length 130 mm Length 130 mm Length 130 mm Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Short code 71AE170/ Short code 71FW170/ Short code 71IE170/ Short code 71TS170/ Short code 71ES170/ Part no A Part no A Part no A Part no A Part no A Length 130 mm Length 130 mm Length 130 mm Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Short code 71AE210/ Short code 71FW210/ Short code 71IE210/ Short code 71TS210/ Short code 71ES210/ Part no A Part no A Part no A Part no A Part no A Length 130 mm Length 90 mm Length 130 mm Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit Sales unit 1 unit

70 70 Wall Trunking Systems CATALOGUE GROUP 70-WIK - S990 Installation device cover plates for trunking systems with 80 system opening Application Cover plates in the colours below (see table) for device installations in trunking systems with 80 system opening. Design The cover plates snap in at the front and fit into the front snap-in accessory mounting box using rest hooks. Versions with labelling panel available on request. Installation devices See Cat. Gr. 78 Installation and connection devices for electrical installation systems. Front snap-in cover plates - S 990-AF 18 Single With a square 50 x 50 mm fitting opening to cover an installation device with a square central insert, for use with front snap-in accessory mounting box 71GD6. Version: cover plate, no labelling panel. Dimensions: W = 86 mm, H = 86 mm. - S 990-AF 28 Double With two square 50 x 50 mm fitting openings to cover installation devices with a central insert, for use with front snap-in accessory mounting box 71GD7. Version: cover plate, no labelling panel. Dimensions: W = 170 mm, H = 86 mm. Part no. Code A S990-AF18/* B S990-AF28/* Pre-assembled power socket units Ready-to-connect pre-assembled single box for front snap-in wall trunking, consisting of: Accessory mounting box with hinged bottom section. Power socket with childproof safety mechanism. Front slot-in S990 cover plate with no labelling panel. Pre-assembled 2 gang power schuko unit *For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M KS990.1 Single power schuko socket supplied in units of 4 cream white RAL 9001 pure white RAL 9010 fire red RAL 3000 light grey RAL 7035 KS gang power schuko socket supplied in units of 2 cream white RAL 9001 pure white RAL 9010 fire red RAL 3000 light grey RAL 7035 KS gang power schuko socket supplied in units of 2 cream white RAL 9001 pure white RAL 9010 fire red RAL 3000 light grey RAL 7035 KS990N.1 1 gang NF type socket supplied in units of 4 cream white RAL 9001 pure white RAL 9010 light grey RAL 7035 KS990N.2 2 gang power NF type socket supplied in units of 2 cream white RAL 9001 pure white RAL 9010 light grey RAL 7035 KS990N.3 3 gang power NF type socket supplied in units of 2 cream white RAL 9001 pure white RAL 9010 light grey RAL 7035 For colour combinations for cover plate and socket, see part code. Other colour combinations available on request BB KS990B1CW KK KS990K1RW KU KS990K1RT MK KS990M1RW BB KS990B2CW KK KS990K2RW KU KS990K2RT MK KS990M2RW BB KS990B3CW KK KS990K3RW KU KS990K3RT MK KS990M3RW BB KS990N/B1CW KK KS990N/K1RW MK KS990N/M1RW BB KS990N/B2CW KK KS990N/K2RW MK KS990N/M2RW BB KS990N/B3CW KK KS990N/K3RW MK KS990N/M3RW

71 Wall Trunking Systems 71 CATALOGUE GROUP 70-WIK Part no. Code Front snap-in accessory mounting box With hinged and, if necessary, removable bottom section to save time connecting cables, with insert openings for cables with a diameter of up to 14 mm Material: polyamide, grey flame-resistant in accordance with DIN VDE 0471 part 2, filament inspection to 750ºC. 71 GD 6 single For fitting of one installation device, 60 mm horizontal fixing track. Dimensions in mm: W = 71, D = 51. Supplied in packs of GD 7 2 gang For fitting of two installation devices (EKR version) or one multiple power socket, including partition wall to enable fitting of installation devices of different voltage ratings. 60 mm vertical fixing centres. Dimensions in mm: W = 142, D = 51. Supplied in packs of AV 71GD BV 71GD ,5 47,5 71 GD 8 For a single appliance with 45mm rest clips. Multiple cable entry points in box sides and box underside. Dimensions in mm: W = 71, H = 42,5. Supplied in packs of GD 9 For 2 or 3 single appliances with 45mm rest clips. Multiple cable entry points in box sides and box underside. Dimensions in mm: W = 160, H = 47,5. Supplied in packs of AV 71GD BV 71GD9 CEE installation unit CEE 16 E2 For fitting a CEE 16 in wall channels with 80 mm covers, consisting of modified front snap-in trunking box and 16 A CEE b CEE16E2 Cover Plates S W H S 990-AF1 single Cover plate for installation of a single accessory, in front-loading mounting box 71 GD 8. Dimensions in mm: W = H = 86. Planning dimension: 71mm A S990-AF1/* S 990-AF2 double Cover plate for installation of 2 accessories, in front-loading mounting box 71 GD 9. Dimensions in mm: W = 170; H = 86. Planning dimension: 160mm B S990-AF2/* S 990-AF3 triple Cover plate for installation of 3 accessories, suitable for teliko wall trunking systems with 80mm cover in combination with front-loading. mounting box 71 GD 9. Dimensions in mm: W = 170; H = 86. Planning dimension: 160mm C S990-AF3/* *For the colour you want, add: the RAL colour number to the short code the code letter to the part number. Colour RAL Code Cream white B Pure white K Light grey M

72 72 Wall Trunking Systems CATALOGUE GROUP 70-WIK Accessories for steel and aluminium wall trunking Part no. Code channels with 80 system opening Trunking divider 61 TW For the internal, horizontal, separation of the base sections of trunking. Self-conductive contacting. Nominal Nominal Standard length supplied: 2000 mm. depth size Material: 1 mm sheet steel, pre-galvanised For nominal depth of A 61TW 65 2/m 2/m 2/m 2/m For nominal depth of C 61TW/ /m 2/m 2/m 2/m For console trunking, nominal depth of A 61TW/P133 Cable retainer 7 KL 80 A /m 2/m Stabilises trunking divider piece and holds 100 2/m 2/m cables in position. oben Material: plastic moulding compound. If used in 81 WIK 2, 2 unit/m recommended C 7KL80A Fitting fixing clamps Insert fitting clamp and push both ends (***) in with a screwdriver. Earth conductor clamp 8AWR For use in the base section of trunking. Material: sheet steel, galvanised. Supplied in packs of CV 8AWR (***) On request: REG installation units for trunking with 110 m cover. Device covers made of aluminium. Clamp units. * Standard colours for painted sheet steel covers and plastic covers. Danger! Metallic components are still live in the event of a fault. Screw the contact screw up to at least 1.2 Nm. Fixing clips 6 RKV3 To fit into on-site cut-outs in sheet steel covers. Note: As the rest clips provide not only the mechanical, but also the electrical connection (earth continuity) to the base section of the trunking, the following minimum numbers must be adhered to with respect to cover cut-outs. Cover lengths: L =< 1000 mm, 4 units. L = mm, 6 units. L > 2000 mm, 8 units. Supplied in packs of B 6RKV3 REG installation unit For in-trunking installation of up to 2 x 3 modules or clamp units to reduce the crosssection in wall trunking with 80 system opening. IKR Installation housing for suspension in divider piece holder loops, with N and PE terminal strips. Material: sheet steel. Device covers 61 GS Perforated made of sheet steel. 1 x 3 Modules painted 2 x 3 Modules painted Device covers 71 GS Perforated made of grooved PVC. 1 x 3 Modules 2 x 3 Modules Clear inspection cover KAB - With transparent swivel hood and fixings, for fitting to device covers. 1 x 3 Modules 2 x 3 Modules B IKR A 61GS3/..* B 61GS6/..* A 71GS3/..* B 71GS6/..* A KAB3/ * B KAB6/..*

73 Wall Trunking Systems 73 CATALOGUE GROUP 70-WIK Fitting installation devices simply snapin Pre-assembled power socket units consisting of a power socket, accessory mounting box and a S-990 cover plate make fitting into wall trunking easier because the individual components have largely been pre-fitted. The power sockets with screw-free plugin terminals are connected to the supply cables in front of the trunking and then inserted into the trunking from the front. Once the trunking has been closed, all that remains is to snap in the S-990 cover onto the accessory mounting box no screws required. The functional design of the S 990 cover range is tailored in terms of shape and colour to our trunking system with the 80 system opening, making it simple to use telecommunications and data installation devices by simple snap-in fixing. The benefits to you Installation times are reduced, from: Pre-assembled combination of power socket and cover. Front snap-in accessory mounting box. Front snap-in S-990 covers, with optional labelling panels.