XC3-19AR-E Module. Operating Manual WUXI XINJE ELECTRIC CO., LTD.
|
|
|
- Percival Robinson
- 5 years ago
- Views:
Transcription
1 XC3-19AR-E Module Operating Manual WUXI XINJE ELECTRIC CO., LTD. 1
2 Catalog CHAPTER 1 BRIEF INTRODUCTION OF THE FUNCTIONS... 3 CHAPTER PROGRAM AND APPLICATION... 7
3 Chapter 1 Brief Introduction of the Functions 1. Basic Performance Integrate logic Control, analog input/output in one body Digital Input:9 points (NPN type optical coupling insulation) Digital Output:1 points (Relay Type) Analog Input:8 points (~1 voltage) Analog Output: points (~1 voltage or ~ma) Support 3 channels AB phase input Support channels high speed count (1KHZ) Simple structure High performance-price ratio, save the space greatly.. General Specification Electric Specification Input Voltage AC1V~V Voltage Allow Bound AC9V~5V Rated Frequency 5/Hz Power Consumption Lower than 1W (TYP.W) Allow Momentary Lower than ms Power-off Power for sensor VDC±1% Maximum ma use Voltage Endurance AC1V-1MA 1 minute (between signal and earth) Insulated Resistance DC5V- about 1MΩ (between signal and earth) Ambient Condition Operating ~5 temperature Storage temperature 1~ Ambient temperature ~85% (no dew) Vibration Endurance 1~5Hz (X,Y,Z direction each 3 minutes G) Anti-interfere Voltage noise: 1Vp-p Ambient Air No corrosive air Protect Structure Fit for IP5F 3
4 Please use the power cable thicker than mm to prevent voltage decrease. Even power off within ms, PLC can keep on working. If long time power off or abnormal voltage decrease, PLC will stop working, output will appear OFF status, when power recovers on, PLC will automatic run Input/Output Specification Digital input/output Input 9 points:x~x1 Output 1 points:y~y11 Input Specification Input signal voltage Input signal current Input ON current Input OFF current Input response time Input signal form Circuit Insulation Input action display DCV±1% 7mA/DCV Up to.5ma Below 1.5mA About 1ms Contact input or NPN open collector transistor Optical coupling insulation LED lights when input is ON
5 Output Specification External Power Circuit Insulation Action Indication Maximum Resistor load Load Inductance load Lamp load Minimum Load Response OFF ON time ON OFF Below AC5V, DC3V Mechanic insulation LED indicate lamp 3A 8VA 1W DC5V ma 1ms 1ms Pulse output XC3-19AR-E has one channel of high speed pulse output Y, the pulse frequency can up to KHz. 5
6 Analog input/output Analog input: 8 channels (~1V voltage) Analog output: channels (~1V voltage or ~ma) Basic parameter table ITEMS Analog input (AD) Analog output (DA) Voltage input Voltage output Current output Analog input bound ~1V - Maximum input bound DC±18V - DC~1V DC~mA Analog output (External load (external load - bound resistor resistor is less KΩ~1MΩ) than 5Ω) Digital input bound - 8 bits binary data (~5) Digital output bound 1 bits binary data (~95) - 1/95(1Bit); the 1/5(8Bit); the converted data is Distinguish ratio converted data is stored into PLC in the form of Hex. stored into PLC in the (8Bit) form of Hex. (1Bit) Colligate precision.8% Convert speed 15ms/ channel ms/ channel Analog using power DCV±1%,1mA Installation Format Can use M3 screws to fix or directly install on DIN77 (width: 35mm) guild Shape and Size (unit: cm) Table of analog quantity with correspond register Analog input Analog output Channel Register Channel Register CH ID CH QD 1CH ID1 1CH QD1 CH ID 3CH ID3 CH ID 5CH ID5 CH ID 7CH ID7
7 High speed counter XC3-19AR-E Increment Pulse+Dir Input AB Phase Mode C C C C C C1 C1 C1 C1 C1 C C C C C C3 C3 C Max.F 1K 1K 1K 1K 1K 1K 5K 5K -times F 1 1/ Count Interrupt X U U A X1 Dir B X U U A X3 Dir B X U X5 U Chapter Program and Application Program Instructions About PLC program, please refer to XC series PLC manual. Program software: XCPpro edit tool. 7
XC3-19AR-E Module. Operating Manual. Thinget Electronic Co., Ltd.
XC3-19AR-E Module Operating Manual Thinget Electronic Co., Ltd. 1 Chapter 1 Brief Introduction of the Functions 1. Basic Performance Integrate logic Control, analog input/output in one body Digital Input:9
XC series PLC expansion module User Manual
XC series PLC expansion module User Manual WUXI XINJE ELECTRIC CO., LTD. This manual includes some basic precautions which you should follow to keep you safe and protect the products. These precautions
S663 Preset Rate/Totalizer Counter
File# E199939 Easily programmed from the front panel Remote reset capability Input variety: Quadrature, Switch, TTL, CMOS, NAMUR, PNP, NPN Software functions include: Password Display Scaling Set Point
S662 Preset Batch/Dual Counter
File# E199939 Easily programmed from the front panel Remote reset capability Input variety: Quadrature, Switch, TTL, CMOS, NAMUR, PNP, NPN Software functions include: Password Display Scaling Set Point
XD series PLC WUXI XINJE ELECTRIC CO., LTD. No.PC
XD series PLC Users manual[hardware](xd3/xd5/xdm) WUXI XINJE ELECTRIC CO., LTD. No.PC01 20160323 3.3 XD series PLC Users manual[hardware] (XD3/XD5/XDM) 1 Preface 2 XD series PLC summary 3 PLC specifications
PLC-K506 Series FEATURES DESCRIPTION FEATURES
FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate With Up to 32 Devices DESCRIPTION
SENSORS S2Z SERIES MAXI SENSORS CARATTERISTICHE APPLICATIONS HIGHLIGHTS
MAXI SENSORS S2Z SERIES The new S2Z Maxi series offers 4 models, with basic optic functions: - through beam - polarized retroreflex - diffuse proximity - background suppression Versions with continuous
AIO and DIO PFXLM4B01DAK:Sink Output Type PFXLM401DAC:Source Output Type Virtual Resolution (pixels)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
PFXLM4B01 D * * (1) (2) (3) (4)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES
FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate with up to 32 devices DESCRIPTION
Inductive Proximity Sensor
Authorised Distributors:- Intech Systems Chennai Pvt. Ltd, Chennai-600 032 Ph: +91 44 4353 8888 Fax: 044 4353 7888 E-mail: info@intechchennai.com Website: www.intechchennai.com distance Supply voltage
Pulse Scaler for DIN Rail Attachment
Type 651 Pulse Scaler for DIN Rail Attachment Programmable pulse scaling factor up to 2047:1 NAMUR generator input PNP transistor output Max. pulse frequency 5 khz PROGRAMMING The divisor is set in binary
S660 Preset Totalizer Counter
File# E199939 Easily programmed from the front panel Remote reset capability Input variety: Quadrature, Switch, TTL, CMOS, NAMUR, PNP, NPN Software functions include: Password Display Scaling Set Point
DEA 115, Digital Input/Output Modules
Catalog 12 Input/Output Modules for S5 115 DEA 115, Digital Input/Output Modules Digital input/output module The digital input modules from the Systeme Helmholz GmbH convert the external binary signals
PG Interface Card "OPC-E2-PG"
Instruction Manual PG Interface Card "OPC-E2-PG" Thank you for purchasing this PG interface card "OPC-E2-PG." Installing this card to your inverter enables speed control with speed sensor and pulse train
CM3-SP04EAO CM3-SP04EAA CM3-SP04EOAI CM3-SP04EOAV
CM3-SP04EAO CM3-SP04EAA CM3-SP04EOAI CM3-SP04EOAV General Specifications Analog Input (Specifications) Items Specification Standards Operating Temp. Storage Temp. Operating Humidity Storage Humidity Vibration
No mark Time-limit SPDT (1c) A Time-limit DPDT (2c) B Time-limit SPDT (1c), Instantaneous SPDT (1c) S DIN W48 H48mm.
Series Digital LCD Timer DIN W48 H48mm Features Power supply : 4-4VAC 5/6Hz, 4-4VDC universal Easy to switch Up/Down mode programmable output modes and timing ranges () Selectable function by front digital
TL-W. Standard Flat Inductive Proximity Sensors. Ordering Information. Front and side facing surface IP67 DC 2-wire and DC 3-wire models
Standard Flat Inductive Proximity Sensors Front and side facing surface IP67 DC -wire and DC -wire models Ordering Information DC -wire Models Shape distance Model Output and operating status mm MD1 *1
XC-E6TCA-P Temperature control module User s manual
XC-E6TCA-P Temperature control module User s manual Xinje Electronic Co., Ltd. Catalog 1. Summarization... 3 1.1 Introduction... 3 1.2 Features... 3 1.3 Using requirements... 3 2 PID self-study introduction...
Solid-State Digital Counter H7AN
Solid-State Digital Counter Preset and Totalizing Counters with Up to 8-Digit LED Displays Draw-out construction allows setting, servicing without disconnecting wiring Choose from selectable UP/DOWN or
Power supply voltage Output configuration Output code Resolution (pulses/rotation) Connection method Model
60-mm-dia. Encoder Rugged Encoder for High-precision Detection of Automatic Machine Timing Rugged construction with the highest shaft loading. Radial: 120 N, Thrust: 50 N IP65f water- and oil-proof construction.
WHEN A PLC IS TOO MUCH, AND SPACE FOR
WHEN A PLC IS TOO MUCH, AND SPACE FOR A RELAY SEQUENCE CIRCUIT IS TOO LITTLE Pattern Selector 59 2.33 66 2.6 70 2.75 No programming required Select from among 15 preset patterns Wiring far simpler than
NPN PNP NPN PNP NPN PNP
Cam Positioner Low-Cost, High-Performance Electronic Cam Switch for Use with OMRON E6F Rotary Encoder Control outputs can be programmed to turn ON/OFF in 1 units of rotary encoder shaft rotation Handles
UniStream Uni-I/O Modules
UniStream Uni-I/O Modules Technical Specifications UIS-WCB1 This guide provides specifications for Unitronics Uni-I/O Wide module UIS-WCB1. This module comprises: 10 Digital inputs, 24VDC, sink/source,
2.1 General Specifications
Chapter 2. 2.1 General Specifications Table 2.1 shows general specifications of the GLOFA GM series and MASTER-K series. No Item Specifications Standards 1 2 3 4 Operating ambient temperature Storage ambient
Product Discontinuation Notices
PRODUCT NEWS Product Discontinuation Notices August 1, 2011 Ultrasonic Sensors No. 2011264E Discontinuation Notice of Ultrasonic Sensor E4A special specification model, E4B special specification model,
Ultraminiature Photoelectric Switches with Self-contained Amplifier
Ultraminiature Photoelectric Switches with Self-contained Amplifier HPJ Series Fingertip-size, Provided with a various slit attachments. (six types) Fingertip-size 22 x 11 x 8 mm (thru scan model) 30 x
Multi Function Timer with Free power, Compact size W38 H42mm
Multi Function with Free power, ompact size W8 H4mm Features Wide power supply range : 100-40VA 50/0Hz, 4-40VD (universal), 4VA 50/0Hz / 4VD (universal), 1VD Various output operations( operation modes)
High Reliability Of Fiber Optic Amplifier For Convenient Mounting
Amplifier Reliability Of Amplifier For Convenient Mounting Features speed response: Max. 0.5ms Auto (Button setting)/remote synchronization input, mutual interference protection, selfdiagnosis Reverse
D7F. Detects Changes in Machine. Vibration. Vibration Sensor with Linear Output or Manual Setting. Ordering Information
with Linear Output or Manual Setting Detects Changes in Machine ON/OFF output can be set and checked quickly and easily from the vibration level meter. waveforms can be checked using the AC monitor output.
20 AMP POWER RELAY HG RELAYS. a HG HG HG Unit weight. Ex. HG 2 AC 240 V
20 AMP POWER RELAY HG RELAYS a 3 1.4 5 RoHS Directive compatibility information http://www.nais-e.com/ a.0 50.0 1.99 8.0 2. FEATURES Large capacity 20 A 250 V AC resistive and 1.5 kw 3 phase 220 V AC motor
EE-SX770/771/772/870/871/872(A/P/R)
EE-SX770/771/772/870/871/872(A/P/R) Thin, Compact Photomicrosensor with Attached Cable H Next generation design available with NPN or output H Allows standard M3-screw mounting H Twenty-four models available
HG RELAYS 20 AMP POWER RELAY FEATURES SPECIFICATIONS
20 AMP POWER RELAY RELAYS a 3 1.4 5 a.0 50.0 1.99 8.0 2. FEATURES Large capacity 20 A V AC resistive and 1.5 kw 3 phase 220 V AC motor loads High contact reliability after long use Usable with direct soldering,
CQM1H-MAB42 Analog I/O Board Connector CN1: Analog inputs 1 to 4. Name Specifications Model number Slot 1 (left slot) High-speed Counter Board
Inner Boards The six available Inner Boards are shown below. Inner Boards can be mounted in slot 1 or slot 2 of a CQM1H-CPU51 or CQM1H- CPU61 CPU Unit. (Some Inner Boards must be mounted in either slot
Calhoon MEBA Engineering School. Study Guide for Proficiency Testing Industrial Electronics
Calhoon MEBA Engineering School Study Guide for Proficiency Testing Industrial Electronics January 0. Which factors affect the end-to-end resistance of a metallic conductor?. A waveform shows three complete
Proximity Sensor Terminology
The following descriptions refer to the European standard EN 60947-5-2. of 2007. The specifications given here are intended to be minimum performance values described by the standard. Alignment must not
PROXIMITY SENSOR TERMINOLOGY
Never use this desk reference for installation or operation of equipment. Refer to manual for installation and operation instructions. The following descriptions refer to the European standard EN 60947-5-2.
Position Detection Switch
521 ZE Type(Solid State) Item Type ZE135 ZE155 ZE235 ZE255 Wiring Method 2 Wire System 3 Wire System 2 Wire System 3 Wire System Lead Wire Leading Direction Straight Type L-shaped Power-supply Voltage
FC Series Signal Conditioners
FC Series Signal Conditioners FC-33 DC Selectable Signal Conditioner with 3-way isolation Field configurable input and output ranges of 0-5V, 0-10 V, 0-20 ma and 4-20 ma with 1500 VDC isolation between
PFXLM4201T A D * * (1) (2) (3) (4) (5) (6)
Model:PFXLM4201TADDK PFXLM4201TADDC PFXLM4201TADAK PFXLM4201TADAC Model Name Indication Notice to our valued customers who use LT4000M series (analog model) : You may experience instances when analog signals
General specifications and features
General specifications and features General specifications and features Table 1 General AC/DC/Relay DC/DC/Relay DC/DC/DC Order number 6ES7 212-1BE31-0XB0 6ES7 212-1HE31-0XB0 6ES7 212-1AE31-0XB0 Dimensions
This data sheet is only valid in association with the IL SYS INST UM E user manual.
Inline counter terminal, version for extreme conditions, 1 counter input, 1 control input, 1 output, 24 V DC, 500 ma Data sheet 106148_en_03 PHOENIX CONTACT 2015-11-04 1 Description The terminal is designed
MINIATURE POWER RELAY IN DS RELAY SERIES FEATURES resistance ORDERING INFORMATION. Ex. DSP 1 L DC12V R
MINIATURE POWER RELAY IN DS RELAY SERIES DSP- RELAYS DSPa DSP SPECIFICATIONS.. DSPa Coil (polarized) (at C F) Minimum mw power coil latching mw mw power coil latching mw.... Contact Arrangement a ab a
G2RV-SL Slim I/O Relay will be discontinued February 2019
NO: RL-162 PRODUCT: G2RV-SL Slim Relay DATE: February 2018 TYPE: Discontinuation Notice G2RV-SL Slim I/O Relay will be discontinued February 2019 Discontinuation Date: February 2019 Note: Date is subject
Solid-State Timer. ON-delay, Repeat cycle/signal OFF start, Repeat cycle/signal ON start, Signal ON/OFF-delay, Signal OFF-delay, and Interval
Solid-State Timer Analog Set Multifunction Timers in Slim Design for Track Mounting All settings are made though front panel Six operating modes in a single timer provides flexibility for many applications
Optimising controls Vacuum switches
Vacuum switches, pneumatic Converts a vacuum level to a pneumatic signal. Vacuum-actuated membrane linked to a pneumatic switch. Available preset or with adjustable vacuum level. Unit Value Feed pressure,
PHOTOELECTRIC S300 MAXI SENSORS APPLICATIONS.
PHOTOELECTRIC MAXI SENSORS sensors S300 The S300 series of advanced MAXI photoelectric sensors represents the most suitable solution for critical applications thanks to excellent performances and resistance
HPJSeries HPJ. Ultraminiature Photoelectric Sensors with Self-contained Amplifier
Ultraminiature Photoelectric Sensors with Self-contained Amplifier HPJSeries HPJ Fingertip-size, Provided with a various slit attachments. (six types) Fingertip-size 22 x 11 x 8mm (thru scan model) 30
EP-5111, EP-5112, EP-5212, EP-5261, EP-5311, EP-5422, EP-5442
October 2017 RSTI-EP Slice I/O Specialty Modules EP-5111, EP-5112, EP-5212, EP-5261, EP-5311, EP-5422, EP-5442 Module Status LED Channel Status LED GE provides several RSTi-EP specialty modules, which
Operating mode. distance. 7 m Light ON Dark ON (selectable) 2 m [100 mm] (See note 1.) 100 mm (wide view)
![Operating mode. distance. 7 m Light ON Dark ON (selectable) 2 m [100 mm] (See note 1.) 100 mm (wide view)](/thumbs/83/88087955.jpg "Operating mode. distance. 7 m Light ON Dark ON (selectable) 2 m [100 mm] (See note 1.) 100 mm (wide view)")
Built-in Amplifier Photoelectric Sensor E3S-A/B Revolutionary High-performance High-quality Sensor with Built-in Amplifier can be adjusted in seconds because the optical axis coincides with the mounting
Capacitive Proximity Sensor
Capacitive Proximity Sensor Compact and Ideal for Robot Hands and Various Built-in Applications for LCD, Wafer, and PDP (Plasma Display Panel) Detection Flat head is only 5.5-mm thick. Robot Cable ensures
General-Purpose Photoelectric Sensors with Self-Contained Amplifier
General-Purpose Photoelectric Sensors with Self-Contained Amplifier HP Series The convenience of industry standards, plus reliability. Effective light axis alignment 50% power savings Prevention of accidental
Incremental encoders Redundant sensing, isolated blind hollow shaft ø mm, cone shaft ø17 mm pulses per revolution
Features Robust, compact housing Two bearings with large distance, one at each end High shaft load up to 450 N Shock resistant up to 250 g Shaft insulation up to 2.8 kv Highest operating speed 10000 rpm
UMK M A A. RoHS-Compliant. 2-Phase Stepping Motor and Driver Package. Features. Product Number Code. Product Line
RoHS-Compliant Stepping Motor and Package UMK Series Additional Information Technical reference Page F- The UMK Series is a -phase stepping motor (resolution: per rotation) with easy-handling AC input
Model Number Structure. Ordering Information. Solid-state Power OFF-delay Timer H3DE-H. Model Number Legend. List of Models
Solid-state Power OFF-delay Timer H3DE-H Timers Two delay-time models available. 0.1 to 12 seconds (S Series) 1 to 120 seconds (L Series) Covers wide range of supply voltage. Model Number Structure Model
F4 04DAS 1 4-Channel Isolated 4 20mA Output
F44DAS 4-Channel Isolated 4mA F44DAS 4-Channel Isolated 4mA Module Specifications The F44DAS 4-channel Isolated Analog module provides several features and benefits. ANALOG 4 CHANNELS PUT F44DAS 4-Ch.
Count/Time Totalizers
/Time Totalizers Compact or Time Totalizers with Easy-to-Read and NEMA 4 Protection High-visibility, 8.5 mm negative transmissive LCD. NEMA 4 when used in conjunction with Y92S-32 rubber gasket supplied
BS-3520 Digital Indicator
BS-3520 Digital Indicator The Better Way for Weighing & easurements Table of Contents. Introduction...3 - Trait... 3-2 Warning... 4 2. Specification...5 3. External Size...6 4. Description on Front Panel...7
Multifunctional counter tico 772/773/774
Universally applicable as a tachometer, timer, shift counter, batch counter Easy to operate Four different backlight colours Intensity of backlighting can now be adjusted Large, clearly readable 48 x 48
Enclosure rating. LED indicator with test button G2R-1-SNI G2R-2-SNI Unsealed Diode. LED indicator and diode with test button G2R-1-SNDI G2R-2-SNDI
General-purpose Relay CSM_GR-_-S_DS_E Slim and Space-saving Power Plug-in Relay Lockable test button models now available. Built-in mechanical operation indicator. Provided with nameplate. AC type is equipped
G70R-SOC08 CSM_G70R-SOC08_DS_E_2_1
Relay Terminal CSM DS_E 1 Space-saving and Labor-saving 8-point Output Block Relay terminal is just 136 80 55 mm (W H D, when mounted upright). Independent contacts and short bar allow easy common connections.
General Specifications
General Specifications Model UM330 Digital Indicator with Alarms GS 05F0D00E General Model UM330 Digital Indicator with Alarms is a precision alarm instrument with universal input /8DIN. For excellent
2000 h at 25 C Battery, charging time h at 25 C Battery, charging time. 8 mm 8 mm via push-button decade switches
ddition/subtraction Counters ddition/subtraction counters preselections or decade devices Order code KCX-WM-V KCX-WM-V Technical data General data Preselection Counter storage Controls and displays Type
General Specifications
General Specifications MODEL UM0 Digital Indicator with Alarms GS 0F0D00E General Model UM0 Digital Indicator with Alarms is a precision alarm instrument with universal input /8DIN. For excellent monitoring
General Specifications
General Specifications GS 77J04H0-0E Model MH Isolator (Free Range Type) General The MH is a plug-in type isolator that converts DC current or DC voltage signals into isolated DC current or DC voltage
Scanning Laser Range Finder
Date: 2011.11.25 Scanning Laser Range Finder UTM-30LX-EW Specification Symbol Amendment Details Amendment Date Amended by Number Approved by Checked by Drawn by Designed by MORI KAMITANI TAGAMI HINO Drawing.
Electronic Thermostat TE-1 Version according to EN
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 3639 Fulda, Germany Postal address: 3635 Fulda, Germany Phone: +49 661 63- Fax: +49 661 63-67 e-mail: mail@jumo.net Internet: www.jumo.net JUMO
Fuzzy Temperature Controllers E5AF
Fuzzy Temperature Controllers 1/4 DIN Controller Combines Fuzzy and PID Control For Fast Response to Process Disturbances Advanced PID control provides optimal response during start-up and steadystate
onlinecomponents.com
Analog Photoelectric Sensor Analog Output Proportional to Light Received, Ideal For Inspection and Measurement Analog object detection ideal for position, size, color and surface characteristics Both analog
Distance-setting Photoelectric Sensor
Distance-setting Photoelectric Sensor The Combination of the Hyper LED and Shine-proof Achieves both Ease-of-use and High Performance Hyper LED mounted. Finest pin-point beam in the industry allows detection
RDV-X/RDV-P Robot driver Only for pulse train control
Single axis Robot driver Only for pulse train control As the size is small and weight is light, it is easy to use in automated machinery. Features 1 Dedicated pulse train control The dedicated pulse train
12 V DC ±10 % 150 ma max. 130 ma max. 120 ma max.
96 PHOTO PHOTO ON/OFF Input SERI Related Information General terms and conditions... F-3 General precautions... P.9 MEASURE panasonic.net/id/pidsx/global Multi-functional D rail mounting slim sensor controller
High Accuracy Eddy Current Type Displacement Sensor GP-A SERIES. Resolution 0.04 % F.S., Linearity ±0.5 % F.S., IP67G environment resistance
1 High Accuracy Eddy Current Type Sensor SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.1 guide... P.11~ General precautions... P.19 PHOTO PHOTO MEASURE panasonic.net/id/pidsx/global
Ultra-Slim PLC (FP Sigma)
Ultra-Slim PLC (FP Sigma) Real-world motion and temperature control. Arc and linear interpolation is very handy for pick & place (linear) or glue (arc) applying applications. With the combination of FP
DIGEM f 96 x 48 EK. Applications. Description
3-349-002-03 1/7.98 Front panel dimensions: 96 x 48 mm LED display: red or green, 14 mm high Max. display range: 19 999 to + 32 765 Modular connectors for flexible use Simple adjustments at front panel
DCS810 Brushed DC Servo Drive
Datasheet of Brushed DC Servo Drive DCS810 DCS810 Brushed DC Servo Drive 18-80VDC, 0-20A, 20-400W Based on DSP control technology and high smooth servo control algorithm Parameter visible tuning tools,
Incremental encoders Blind hollow shaft or cone shaft pulses per revolution
Features TTL output driver for cable length up to 550 m Very high resistance to shock and vibrations Hybrid bearing for extended service life Shaft insulation up to.8 kv Large terminal box, turn by 80
DIN48 SIZE ANALOG MULTI-RANGE CYCLIC TWIN TIMERS
DIN SIZE ANALOG MULI-ANGE CYCLIC WIN IMES UL File No.: E122222 CSA File No.: L39291 FEAUES A single twin timer unit that repeats (variable) ON/OFF. Multiple ranges with a.1 s to 5 h time specification
Ordering Information. Stepping Relay Unit G9B. Model Number Legend
Stepping Relay Unit CSM DS_E_4_1 Ideal for Controlling Pumps and Production Lines with Six or Twelve Stepping Circuits Built-in relays switch 2 A at 250 VAC or 30 VDC. Initialization of stepping with reset
CMM System - Encapsulated Modules
CMM System - Encapsulated Modules Bearing Monitoring BMM-40 BDM-40 BMM-42 BDM-42 DMM-13 DMM-12 SPM 40000 SPM 42000 45011-L (max. 4 m) 45011-L (max.100 m) VMM-14/15 VMM-20/21 VDM-14/15 VDM-20/21 90296-L
Opaque materials of Min. Ø60mm. Hysteresis - Max. 10% at rated setting distance
Small and light, common type Features Easy to mount at a narrow space with small size and light weight. Convenient to adjust the sensitivity by external sensitivity adjustment control.(diffuse reflective
Programmable Universal Frequency Transducer
Programmable Universal Frequency Transducer Data Sheet 0A April 000 Features Completely programmable frequency range from 0. Hz 0 khz (programmed using membrane keypad) LCD to display the input or output
HPA Series. Self-contained Photoelectric Controls with High Functions. Specifications CLICK FEATURES ORDER GUIDE. Pre-leaded type (2m lead)
6 HPA Series Specifications Self-contained Photoelectric Controls with Functions FEATURES Strobe Light Emission, Margin Regulation, Front Incoming Light Display, and Output Inhibit Functions Allow Sensing
И М. 2 24VAC 50/60Hz, 24-48VDC VAC 50/60Hz
8 Pin Plug Type DIN W48 H48mm 8 Pin Plug Features Upgraded counting speed: 1cps / 3cps / kcps / 5kcps Selectable voltage input (PNP) method or no-voltage input () method Decimal point setting (fixed decimal
SLIM COMPACT SAFETY RELAY
SLIM COMPACT SAFETY RELAY SF-RELAYS Slim type Max. 24.945 Max. 24.945 Max. 4.575 Max. 5.969 Max. 3.52 Max. 3.52 mm inch FEATURES Forcibly guide contact structure (EN525 ClassA TÜV recognized) Slim profile
High Accuracy Eddy Current Type Displacement Sensor GP-A SERIES. Resolution 0.04 % F.S., Linearity ±0.5 % F.S., IP67g environment resistance
13 High Accuracy Eddy Current Type Sensor SERIES Related Information General terms and conditions... F- Glossary of terms... P.139 Sensor selection guide... P.9~ General precautions... P.1 PHOTO PHOTO
Incremental Rotary Encoder E6B2
Incremental Rotary Encoder General-Purpose Rotary Encoder Withstands arge Shaft oads Wide variety of supply voltages and output forms Easy-to-adjust zero index (phase Z) with origin indicating function
:PMM-BA ø 60 ø 86 ø 106
Pulse I/ (AC power input) The -Phase Stepping Driver PMM-BA-- PMM-BA-- ACV/V -step/half-step ( x division) ( x divisions) Applicable motor ø ø ø Characteristics lexible These drivers can drive various
Contents H3CR. DIN 48 x 48-mm Multifunctional Timer Series. Broad Line-up of H3CR Series H3CR-A. Solid-state Timer. Common to ALL Timers
Solid-state Timer H3CR DIN 48 x 48-mm Multifunctional Timer Series Conforms to EN61812-1 and EN60664-1 (VDE0110) 4 kv/2 for Low Voltage, and EMC Directives. Approved by UL and CSA. Lloyds/NK approvals.
E2S World's Smallest Square Sensor with Built-in Amplifier
Compact Square Inductive ES World's Smallest Square Sensor with uilt-in mplifier Features 5.5 mm World's Smallest Sensor with uilt-in mplifier The 5.5 mm x 5.5 mm type permits smaller, space-saving machines
General Specifications
General Specifications GS 05F01D01E MODEL UM351 Digital Indicator with Alarms with Active Color PV Display General Model UM351 Digital Indicator with Alarms is a precision alarm instrument provided with
VersaPoint I/O Module
Module provides two-input channels for resistive temperature sensors. It supports platinum or nickel sensors according to the DIN standard and SAMA Directive. In addition, CU10, CU50, CU53, KTY81 and KTY84
Two outputs: contact and non-contact
SRIS Sensor Controller Multi-functional slim sensor controller DI rail mounting Two outputs: contact and non-contact Connects two sensors -C7W Mountable on 3 mm.378 in DI rail by one-push. It reduces mounting
FX-CM. HQ Color Mark Sensor. Model Number Legend SALIENT FEATURES. Sensors. Proximity. Photoelectric. Sensors
HQ Color Mark Sensor SALIENT FEATURES 18mm ±2mm Pushbutton Teach RGB LED light source 8 Remote Memory Setting Shock Resistant casing - 50G Model Number Legend 1 2 3 4 5 1. Series 4. Output FX 2. Type CM:
Absolute Rotary Encoder
Absolute Rotary Encoder Use the Tough (Rated IP64 for Degree of Protection) Combined with a PLC or Cam Positioner for Optimum Control and Ease-of-Use Incorporates a sealed bearing, meeting IP64 for durability
analog output inductive sensors analog output for distance control analog
for distance control analog output inductive sensors KEY ADVANTAGES ü Highest sensing ranges ü Best temperature stability ü Excellent repeat accuracy ü Resolution in µm range Range overview Housing size
Model Number Structure
Total Counter/Time Counter (DIN 72 x 36) CSM DS_E_4_1 DIN 72 x 36-mm Total Counter/Time Counter with Easy-to-read Displays and Water and Oil Resistance Equivalent to IP66 Large, easy-to-read displays:
Built-in Amplifier Photoelectric Sensor
Built-in Amplifier Photoelectric Sensor Easy-to-use, Low-cost Photoelectric Sensor Incorporating s that can be clearly seen from a distance Conforms to EN and IEC standards Incorporating polarizing function,
ECM3 EARTH CONTINUITY RELAY
TECHNICAL DATASHEET ECM3 EARTH CONTINUITY RELAY Electrical Protection for Hard Rock Mines Application The ECM3 has been designed to provide earth continuity protection for cables containing pilot cores.
High Speed Response Type With Built-in Output Protection Circuit
High Speed Response Type With Builtin Output Protection Circuit Features Reverse power polarity and overcurrent High speed response: Max. ms ight /Dark mode selectable by control wire Builtin the sensitivity