Compact & Powerful Inverter STARVERT ig5a 0.4~1.5kW 1phase 200~230Volts 0.4~22kW 3Phase 200~230Volts 0.4~22kW 3Phase 380~480Volts

Transcription

1 Compact & Powerful Inverter STARVERT ig5a 0.4~1.5kW 1phase 200~230Volts 0.4~22kW 3Phase 200~230Volts 0.4~22kW 3Phase 380~480Volts

2 Inverter STARVERT ig5a LS Starvert ig5a is very competitive in its price and shows an upgraded functional strength. User-friendly interface, extended inverter ranges up to 22kW, superb torque competence and small size of ig5a provides an optimum use environment. Standard compliance Compactness ig5a High performance Userfriendliness & Easy maintenance 2

3 Compact & Powerful Inverter ig5a Contents Overview Model & Type Standard Specifications Wiring Terminal Configurations Keypad Features Parameter Setting Trial Run Dimensions Braking Resistors and Peripheral Devices Function List Protective Functions Fault Remedy 3

4 ig5a Powerful & Upgraded Performance ig5a provides sensorless vector control, PID control, and ground-fault protection through powerful built-in functions. Sensorless vector control The built-in sensorless vector control provides the superb speed control and powerful high torque. Torque (%) Speed vs Torque Characteristics Ground-fault protection during running The ground-fault protection of output terminal is possible during running. Condition : Sensorless Vector Control Mode: Auto tuning Measure maximum torque (%) at each speed (1/5/10/20/30/40/50/60Hz) Speed (Hz) Analog control from -10V to 10V Inputting analog signals from -10V to 10V provides user-friendly operation. +10 Forward -10 Reverse Built-in PID control The built-in PID function enables to control flow-rate, oil-pressure, temperature, etc without any extra controller. PID control PI control Built-in dynamic braking circuit The built-in dynamic braking circuit minimizes deceleration time via braking resistors. Speed With braking resistor Normal state Built-in 485 communication The built-in RS-485 communication supports remote control and monitoring between ig5a and other equipment. Wide product range ig5a consists of the product range from 0.4 to 22KW. Reducing deceleration time Time 4

5 Compact & Powerful Inverter ig5a RS-485 communication Connected to PC RS C converter Monitoring Checking operation status (Voltage, Current, Frequency, etc) Checking modified parameters Windows support Remote Control Convenient remote control to modify operation status (Forward/Reverse operation, Frequency, etc) Easy parameter setting Available to control up to 31 Inverters RS-485, Modbus communication Connected to XGT panel Monitoring Checking operation time Automatic list-up of trip record Language support (Korean, English, Chinese) Remote Control Convenient remote control to modify operation status (Forward/Reverse operation, Frequency, etc) Easy parameter setting Available to control up to 31 Inverters RS-485, Modbus communication 5

6 ig5a User-friendly Interface & Easy Maintenance The parameter setting becomes easier by adopting the 4 directions key. And ig5a supports easy maintenance via diagnosis and fan changeable structure. Diagnosis of output module Through easy parameter setting, ig5a can diagnose the status of output module. Easy change of fan ig5a is designed to be the fan changeable structure in preparation for a fan breakdown. Cooling fan control By controlling the cooling fan, ig5a provides a virtually quiet environment according to the status of operation. User-friendly interface The 4 directions key provides easy handling and monitoring. External loader (Optional) The external loader away from a panel enables to control and monitor conveniently. And the parameters made by external loader can be copied and applicable to other Inverters. Loader type + External type (Optional) Model name INV, REMOTE KPD 2M (SV-iG5A) INV, REMOTE KPD 3M (SV-iG5A) INV, REMOTE KPD 5M (SV-iG5A) Remarks 2m 3m 5m 6

7 Compact & Powerful Inverter ig5a Compact Size The compact size achieves cost-efficiency and various applications. Same height from 0.4 to 4.0kW (128mm) Global standard compliance CE UL Global standard ig5a series complies with CE and UL standards. PNP/NPN input Both PNP and NPN inputs become possible and these enable to use the outer power. To do so, users will be given wider choices of selecting the controller. 7

8 ig5a Model & Type Applicable motor ranges 1 Phase 200V 3 Phase 200V 3 Phase 400V 0.4kW (0.5HP) SV004iG5A-1 SV004iG5A-2 SV004iG5A kW (1HP) SV008iG5A-1 SV008iG5A-2 SV008iG5A-4 1.5kW (2HP) SV015iG5A-1 SV015iG5A-2 SV015iG5A-4 2.2kW (3HP) SV022iG5A-2 SV022iG5A-4 3.7kW (5HP) SV037iG5A-2 SV037iG5A-4 4.0kW (5.4HP) SV040iG5A-2 SV040iG5A-4 5.5kW (7.5HP) SV055iG5A-2 SV055iG5A-4 7.5kW (10HP) SV075iG5A-2 SV075iG5A kW (15HP) SV110iG5A-2 SV110iG5A kW (20HP) SV150iG5A-2 SV150iG5A kW (25HP) SV185iG5A-2 SV185iG5A kW (30HP) SV220iG5A-2 SV220iG5A-4 SV 015 ig5a 2 STARVERT Motor rating (kw) (004: 0.4kW~220: 22kW) ig5a series Input voltage (1: 1 phase 200~230[V], 2: 3 phase 200~230[V], 4: 3 phase 380~480[V]) 8

9 Compact & Powerful Inverter ig5a Standard Specifications 1 Phase 200V SV ig5a Max. capacity 1) Output rating (HP) (kw) Capacity (kva) FLA (A) 3) Max frequency 2) [Hz] 4) Max voltage 3 phase 200~230V 5) Input rating Rated voltage Rated frequency 1phase 200~230 VAC (+10%, -15%) 50~60 [Hz] (±5%) Cooling method Forced air cooling Weight (kg) Phase 200V SV ig5a-2 Max. (HP) capacity 1) (kw) Capacity (kva) 2) Output FLA (A) 3) rating Max frequency Max voltage Input Rated voltage rating Rated frequency Cooling method Weight (kg) [Hz] 4) 3 phase 200~230V 5) 3 phase 200~230 (+10%, -15%) 50~60 [Hz] (±5%) N/C 6) Forced air cooling Phase 400V SV ig5a-4 Max. capacity 1) (HP) (kw) Capacity (kva) 2) Output FLA (A) 3) rating Max frequency Max voltage Input rating Rated voltage Rated frequency Cooling method Weight (kg) N/C 6) [Hz] 4) 3 phase 380~480V 5) 3 phase 380~480 VAC (+10%, -15%) 50~60 [Hz] (±5%) Forced air cooling ) Indicate the maximum applicable motor capacity when using 4 pole LS standard motor. 2) Rated capacity is based on 220V for 200V series and 440V for 400V series. 3) Refer to 15-3 of user s manual when carrier frequency setting (39) is above 3kHz. 4) Max. frequency setting range is extended to 300Hz when H40 (Control mode select) is set to 3 (Sensorless vector control). 5) Max. output voltage cannot be higher than the input voltage. It can be programmable below input voltage. 6) Self-Cooling 9

10 ig5a Standard Specifications Control Control method Frequency setting resolution Frequency accuracy V/F pattern Overload capacity Torque boost Dynamic braking Operation mode Frequency setting Operation features Max. braking torque Max. Duty V/F, Sensorless vector control Digital command: 0.01Hz Analog command: 0.06Hz (Max. freq.: 60Hz) Digital command: 0.01% of Max. output frequency Analog command: 0.1% of Max. output frequency Linear, Squared, User V/F 150% per 1 min. Manual/Auto torque boost 20% 1) 150% when using optional DB resistor 2) Keypad/ Terminal/ Communication option/ Remote keypad selectable Analog: 0~10V, -10~10V, 0~20mA Digital: Keypad PID, Up-down, 3-wire NPN/PNP selectable Operation Input Multi-function terminal P1~P8 FWD/REV RUN, Emergency stop, Fault reset, Jog operation, Multi-step Frequency-High, Mid, Low, Multi-step Accel/Decel-High, Mid, Low, DC braking at stop, 2nd motor select, Frequency UP/Down, 3-wire operation, External trip A, B, PID-Inverter (V/F) operation bypass, Option-inverter (V/F) operation bypass, Analog Hold, Accel/Decel stop Output Open collector terminal Multi-function relay Fault output and inverter status output Less than DC 24V, 50mA (N.O., N.C.) Less than AC 250V, 1A; Less than DC 30V, 1A Protective function Analog output (AM) Trip Alarm Momentary power loss 0~10Vdc (less than 10mA): Output freq, Output current, Output voltage, DC link selectable Over voltage, Under voltage, Over current, Ground fault current detection, Inverter overheat, Motor overheat, Output phase open, Overload protection, Communication error, Loss of speed command, Hardware fault, Fan trip Stall prevention, Overload Below 15 msec.: Continuous operation (Should be within rated input voltage, rated output power.) Above 15 msec.: Auto restart enable Environ ment Protection degree Ambient temp Storage temp Humidity Altitude/Vibration Atmospheric pressure Location 1) Means average braking torque during Decel to stop of a motor. 2) Refer to Chapter 16 of user s manual for DB resistor specification. IP 20, NEMA1 (Optional) -10 ~50-20 ~65 Below 90% RH (No condensation) Below 1,000m, 5.9m/sec 2 (0.6G) 70~106 kpa Protected from corrosive gas, Combustible gas, Oil mist or dust 10

11 Compact & Powerful Inverter ig5a Wiring 0.4~7.5kW DB resistor (Optional) 3 phase AC input (Rated input voltage) B1 B2 R S T G U V W Ground 24 P1 P2 24V output FX (Forward run) RX (Reverse run) AM CM Multi-function analog output signal: 0~10V CM Input signal common P3 BX (Emergency stop) P4 RST (Trip reset) P5 JOG (Jog operation) 3A A contact output CM Input signal common P6 Multi-step freq. - Low P7 Multi-step freq. - Middle 3C 3B A/B contact common B contact output P8 Multi-step freq. - High Potentiometer (1kohm, 1/2W) MO Multi-function open collector output VR V1 I 10V power supply for potentiometer Freq. Setting Voltage signal input: -10~10V Freq. Current signal input: 0~20mA MG MO Common S+ RS-485 communication terminal CM Input signal common S- 11

12 ig5a Wiring 11.0~22.0kW DC reactor DB resistor (Optional) 3 phase AC input (Rated input voltage) P1(+) B1 B2 N(-) R U S V T G W Ground 24 P1 P2 24V output FX (Forward run) RX (Reverse run) AM CM Multi-function analog output signal: 0~10V CM Input signal common P3 BX (Emergency stop) P4 RST (Trip reset) P5 JOG (Jog operation) 3A A contact output CM Input signal common P6 Multi-step freq. - Low P7 Multi-step freq. - Middle 3C 3B A/B contact common B contact output P8 Multi-step freq. - High Potentiometer (1kohm, 1/2W) MO Multi-function open collector output VR V1 I 10V power supply for potentiometer Freq. Setting Voltage signal input: -10~10V Freq. Current signal input: 0~20mA MG MO Common S+ RS-485 communication terminal CM Input signal common S- 12

13 Compact & Powerful Inverter ig5a Terminal Configuration Specifications for power terminal block wiring 0.4kW~0.75kW (1 phase) 0.4kW~1.5kW (3 phase) 1.5kW (1 phase) R T B1 B2 R S T B1 B2 R T B1 B2 U V W 2.2~4.0kW (3 phase) U V W U V W 5.5kW~7.5kW (3 phase) R S T B1 B2 U V W 11~22kW (3 phase) B1 B2 U V W R(L1) S(L2) T(L3) P1(+) B1 B2 N(-) U V W R S T SV004iG5A-1 SV008iG5A-1 SV015iG5A-1 SV004iG5A-2 SV008iG5A-2 SV015iG5A-2 SV022iG5A-2 SV037iG5A-2 SV040iG5A-2 SV055iG5A-2 SV075iG5A-2 SV110iG5A-2 SV150iG5A-2 SV185iG5A-2 SV220iG5A-2 SV004iG5A-4 SV008iG5A-4 SV015iG5A-4 SV022iG5A-4 SV037iG5A-4 SV040iG5A-4 SV055iG5A-4 SV075iG5A-4 SV110iG5A-4 SV150iG5A-4 SV185iG5A-4 SV220iG5A-4 R, S, T wire U, V, W wire Ground wire mm 2 AWG mm 2 AWG mm 2 AWG Terminal Screw Size M3.5 M3.5 M4 M3.5 M3.5 M3.5 M4 M4 M4 M5 M5 M6 M6 M8 M8 M3.5 M3.5 M4 M4 M4 M4 M5 M5 M5 M5 M6 M6 Screw Torque (kgf.cm) / lb-in 10/8.7 10/8.7 15/13 10/8.7 10/8.7 10/8.7 15/13 15/13 15/13 32/28 32/ / / / / /8.7 10/8.7 15/13 15/13 15/13 15/13 32/28 32/ / / / /

14 ig5a Terminal Configuration Control terminal specifications MO MG 24 P1 P2 CM P3 P4 S- S+ 3A 3B 3C P5 CM P6 P7 P8 VR V1 I AM Terminal Wire size (mm 2 ) Single wire Stranded Screw size 1) Torque (Nm) Specification P1~P8 Multi-function input T/M M CM Common terminal M VR V1 Power supply for external potentiometer Input terminal for voltage operation M2.6 M Output voltage: 12V Max. output current: 100mA Potentiometer: 1~5kohm Max. input voltage: -12V~+12V input I Input terminal for current operation M ~20mA input Internal resistor: 500ohm AM Multi-function analog output terminal M Max. output voltage: 11V Max. output current: 100mA MO Multi-function terminal for open collector M Below DC 26V,100mA MG 24 3A 3B 3C Ground terminal for external power supply 24V external power supply Multi-function relay output A contact Multi-function relay output B contact Common for multi-function relays M2.6 M2.6 M2.6 M2.6 M Max. output current: 100mA Below AC 250V, 1A Below DC 30V, 1A 1) Use the recommended tightening torque when securing terminal screws. When you use external power supply (24V) for multi-function input terminal (P1~P8), apply voltage higher than 12V to activate. Tie the control wires more than 15cm away from the control terminals. Otherwise, it interferes front cover reinstallation. 14

15 Compact & Powerful Inverter ig5a Keypad Features Display Term RUN Run key Run command STOP/RESET STOP/RESET key STOP: Stop command during operation, RESET: Reset command when a fault occurs. Up key Used to scroll through codes or increase parameter value KEY Down key Right key Used to scroll through codes or decrease parameter value Used to jump to other parameter groups or move a cursor to the right to change the parameter value Left key Enter key FWD Forward run 1) REV Reverse run LED RUN Run key SET Setting 1) 4 LEDs above are set to blink when a fault occurs. Used to jump to other parameter groups or move a cursor to the left to change the parameter value Used to set the parameter value or save the changed parameter value Lit during forward run Lit during reverse run Lit during operation Lit during parameter setting Dimensions 2- SET RUN RUN C L ENT FWD REV STOP RESET

16 ig5a Moving to Other Groups Parameter groups There are 4 different parameter groups in ig5a series as shown below. Parameter group Drive group Function group 1 Function group 2 I/O (Input/Output) group Basic parameters necessary for the inverter to run. Parameters such as Target frequency, Accel/Decel time settable. Basic function parameters to adjust output frequency and voltage. Advanced function parameters to set parameters for such as PID Operation and second motor operation. Parameters necessary to make up a sequence using multi-function input/output terminal. Moving to other groups Moving to other groups using the Right ( ) key Moving to other groups using the Left ( ) key 1) 1) 1) Target frequency can be set at 0.0 (the 1st code of drive group). Even though the preset value is 0.0, it is user-settable. The changed frequency will be displayed after it is changed. 16

17 Compact & Powerful Inverter ig5a When changing ACC time from 5.0 sec to 16.0 sec In the first code 0.00, press the Up ( ) key once to go to the second code. ACC [Accel time] is displayed. Press the Ent ( ) key once. Preset value is 5.0, and the cursor is in the digit 0. Press the Left ( ) key once to move the cursor to the left. The digit 5 in 5.0 is active. Then press the Up ( ) key once. The value is increased to 6.0 Press the Left ( ) key to move the cursor to the left is displayed. The first 0 in 0.60 is active. Press the Up ( ) key once is set. Press the Ent ( ) key once is blinking. 1) Press the Ent ( ) key once again to return to the parameter name. 8 ACC is displayed. Accel time is changed from 5.0 to 16.0 sec. 1) Pressing the Left ( )/Right ( )/Up ( )/Down ( ) key while a cursor is blinking will cancel the parameter value change. Pressing the Ent ( ) key in this status will enter the value into memory. In step 7, pressing the Left ( ) or Right ( ) key while 16.0 is blinking will disable the setting. Code change in Drive group In the 1st code in Drive group 0.00, press the Up ( ) key once. The 2nd code in Drive group ACC is displayed. Press the Up ( ) key once. The 3rd code dec in Drive group is displayed. Keep pressing the Up ( ) key until the last code appears. The last code in Drive group "drc is displayed. Press the Up ( ) key again. Return to the first code of Drive group. Use Down ( ) key for the opposite order. 17

18 ig5a Trial Run Multi-step operation + Run/Stop via FX/RX + Max. frequency change Operation condition Operation command: Run/Stop via FX/RX Frequency command: Multi-step operation [Low (20), Middle (30), High (80)] Max. frequency change: From 60Hz to 80Hz Wiring S1 P1 (Forward) S2 S3 S4 P2 (Reverse) P6 (Low) P7 (Middle) 3 phase AC input R S T G U V W S5 P8 (High) S / W P1 (Forward) P2 (Reverse) CM P6 (Low) P7 (Middle) P8 (High) CM 1. Please make sure that R, S, T are connected to 3 phase AC input, and U, V, W are also motor connection terminals. 2. After supplying the power, please set the frequency of multi-step among Low, Middle, and High. 3. If P1 (FX) turns on, the motor operates in forward. And after turning off, it stops according to the deceleration time. 4. If P2 (RX) turns on, the motor operates in reverse. And after turning off, it stops according to the deceleration time. VR V1 CM Parameter setting Step Command Code Default After change Max. frequency change (FU1) Multi-step frequency (DRV) Multi-step frequency (DRV) Multi-step frequency (I/O) Forward run (P1: FX) Reverse run (P2: RX) F21 st1 st2 I30 I17 I18 Change Max. frequency. Set Low step. Set Middle step. Set High step. The default is FX. This value may change. The default is RX. This value may change. 60Hz 10Hz 20Hz 30Hz FX RX 80Hz 20Hz 30Hz 80Hz FX RX 18

19 Compact & Powerful Inverter ig5a Potentiometer (Volume) + Run/Stop via FX/RX + Accel/Decel time change Operation condition Operation command: Run/Stop via FX/RX Wiring Frequency command: 0~60Hz analog input via potentiometer Accel/Decel time: Accel-10sec, Decel-20sec Potentiometer 1~5kohm, 1/2W VR V1 CM 3 phase AC input R S T G U V W Motor 0~60Hz P1 (FX) Forward P2 (RX) Reverse CM 1. Please make sure that R, S, T are connected to 3 phase AC input, and U, V, W are also motor connection terminals. 2. After supplying the power, please set the frequency of multi-step among Low, Middle, and High. 3. If P1 (FX) turns on, the motor operates in forward. And after turning off, it stops according to the deceleration time. 4. If P2 (RX) turns on, the motor operates in reverse. And after turning off, it stops according to the deceleration time. 5. Control the motor s speed via potentiometer. VR V1 CM Potentiometer 1~5kohm, 1/2W Parameter setting Step Command Code Default After change 1 Operation command (DRV group) Drv Turn on/off motor via terminal. 1 (FX/RX-1) 1 (FX/RX-1) 2 Analog input (DRV group) Frq Change keypad command to analog voltage command. 0 (Keypad-1) 3 (V1: 0~10V) 3 Accel/Decel time (DRV group) ACC dec Set Accel time to 10sec in ACC Set Decel time to 20sec in dec. 5sec (Accel) 10sec (Decel) 10sec (Accel) 20sec (Decel) 4 Forward run (P1: FX) I17 The default is FX. This value may change FX FX 5 Reverse run (P2: RX) I18 The default is RX. This value may change. RX RX 19

20 ig5a Dimensions SV004iG5A-2 / SV008iG5A-2, SV004iG5A-4 / SV008iG5A-4 W W1 A SV004IG5A-2 SV008IG5A-2 SV004IG5A-4 SV008IG5A mm (inches) SV015iG5A-2 / SV015iG5A-4 W W1 A H1 A1 H1 A H D B W1 Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg) D H B W1 SV015IG5A-2 SV015IG5A mm (inches) Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg)

21 Compact & Powerful Inverter ig5a SV022iG5A-2 / SV037iG5A-2 / SV040iG5A-2, SV022iG5A-4 / SV037iG5A-4 / SV040iG5A-4 W C L H1 A D H B W1 B Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg) SV022IG5A-2 SV037IG5A-2 SV040IG5A-2 SV022IG5A-4 SV037IG5A-4 SV040IG5A SV055iG5A-2 / SV075iG5A-2, SV055iG5A-4 / SV075iG5A mm (inches) W A W A H1 H D B W B SV055IG5A-2 SV075IG5A-2 SV055IG5A-4 SV075IG5A mm (inches) Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg)

22 ig5a Dimensions SV110iG5A-2 / SV150iG5A-2 / SV110iG5A-4 / SV150iG5A-4 W A W1 A H1 H D B W1 B mm (inches) Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg) SV110iG5A-2 SV150iG5A-2 SV110iG5A-4 SV150iG5A SV185iG5A-2 / SV220iG5A-2 / SV185iG5A-4 / SV220iG5A-4 W A W1 A H1 H D B W1 B mm (inches) Inverter model (kw) W (mm) W1 (mm) H (mm) H1 (mm) D (mm) A (mm) B (mm) (kg) SV185iG5A-2 SV220iG5A-2 SV185iG5A-4 SV220iG5A

23 Braking Resistors and Peripheral Devices Compact & Powerful Inverter ig5a Braking resistors Voltage Inverter 200V Series 400V Series ) The wattage is based on Enable Duty (%ED) with continuous braking time 15sec. 100% braking 150% braking Resistor [Ω] Watt [W] 1) Resistor [Ω] Watt [W] 1) , ,000 1,400 2,000 2,400 2, ,000 1,400 2,000 2,400 2, , ,200 2,400 2,400 3,600 3, ,000 1,200 2,000 2,400 3,600 3,600 Breakers Model MCCB, ELCB (LS) MC 004iG5A-1 008iG5A-1 015iG5A-1 004iG5A-2 008iG5A-2 015iG5A-2 022iG5A-2 037iG5A-2 040iG5A-2 055iG5A-2 075iG5A-2 110iG5A-2 150iG5A-2 185iG5A-2 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs53 TD125U,EBs53 TD125U,EBs53 TD125U,EBs53 TD250U,EBs53 GMC-9 GMC-9 GMC-12 GMC-9 GMC-9 GMC-12 GMC-18 GMC-32 GMC-32 GMC-40 GMC-50 GMC-65 GMC-100 GMC-100 Model MCCB, ELCB (LS) MC 220iG5A-2 004iG5A-4 008iG5A-4 015iG5A-4 022iG5A-4 037iG5A-4 040iG5A-4 055iG5A-4 075iG5A-4 110iG5A-4 150iG5A-4 185iG5A-4 220iG5A-4 TS250U,EBs53 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs33 TD125U,EBs53 TD125U,EBs53 TD125U,EBs53 TD125U,EBs53 GMC-125 GMC-9 GMC-9 GMC-9 GMC-12 GMC-18 GMC-18 GMC-32 GMC-32 GMC-40 GMC-50 GMC-65 GMC-65 23

24 ig5a Braking Resistors and Peripheral Devices Fuses & AC reactors Model 004iG5A-1 008iG5A-1 015iG5A-1 004iG5A-2 008iG5A-2 015iG5A-2 022iG5A-2 037iG5A-2 040iG5A-2 055iG5A-2 075iG5A-2 110iG5A-2 150iG5A-2 185iG5A-2 220iG5A-2 004iG5A-4 008iG5A-4 015iG5A-4 022iG5A-4 037iG5A-4 040iG5A-4 055iG5A-4 075iG5A-4 110iG5A-4 150iG5A-4 185iG5A-4 220iG5A-4 Current [A] 10 A 10 A 15 A 10 A 10 A 15 A 25 A 30 A 30 A 30 A 50 A 70 A 100 A 100 A 125 A 5 A 10 A 10 A 10 A 20 A 20 A 20 A 30 A 35 A 45 A 60 A 70 A AC external fuse Voltage [V] AC reactor 4.20 mh, 3.5 A 2.13 mh, 5.7 A 1.20 mh, 10 A 4.20 mh, 3.5 A 2.13 mh, 5.7 A 1.20 mh, 10 A 0.88 mh, 14 A 0.56 mh, 20 A 0.56 mh, 20 A 0.39 mh, 30 A 0.28 mh, 40 A 0.20 mh, 59 A 0.15 mh, 75 A 0.12 mh, 96 A 0.10 mh, 112 A 18.0 mh, 1.3 A 8.63 mh, 2.8 A 4.81 mh, 4.8 A 3.23 mh, 7.5 A 2.34 mh, 10 A 2.34 mh, 10 A 1.22 mh, 15 A 1.14 mh, 20 A 0.81 mh, 30 A 0.61 mh, 38 A 0.45 mh, 50 A 0.39 mh, 58 A DC reactor mh, 56 A 0.57 mh, 71 A 0.49 mh, 91 A 0.42 mh, 107 A mh, 29 A 2.18 mh, 36 A 1.79 mh, 48 A 1.54 mh, 55 A 24

25 Function List Compact & Powerful Inverter ig5a Drive Group LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run This parameter sets the frequency that the inverter is commanded to output A100 [Frequency 0 ~ 400 command] [Hz] During Stop: Frequency Command During Run: Output Frequency During Multi-step operation: Multi-step frequency 0. It cannot be set greater than F21- [Max frequency] O ACC dec A101 A102 [Accel time] [Decel time] 0 ~ 6000 [Sec] During Multi-Accel/Decel operation, this parameter serves as Accel/Decel time O 10.0 O 0 Run/Stop via Run/Stop key on the keypad drv Frq St1 St2 St3 A103 [Drive mode] 0 ~ 3 A104 [Frequency setting method] 0 ~ 7 A105 [Multi-Step frequency 1] A106 [Multi-Step 0 ~ 400 frequency 2] [Hz] A107 [Multi-Step frequency 3] FX: Motor forward run 1 RX: Motor reverse run Terminal operation FX: Run/Stop enable 2 RX: Reverse rotation select 3 RS485 communication 4 Set to Field Bus communication 1) 0 Keypad setting 1 Digital 1 Keypad setting 2 2 V1 1: -10 ~ +10 [V] 3 V1 2: 0 ~ +10 [V] 4 Analog Terminal I: 0 ~ 20 [ma] 5 Terminal V1 setting 1 + Terminal I 6 Terminal V1 setting 2+ Terminal I 7 RS485 communication 8 Digital Volume 9 Set to Field Bus communication 1) Sets Multi-Step frequency 1 during Multi-step operation. Sets Multi-Step frequency 2 during Multi-step operation. Sets Multi-Step frequency 3 during Multi-step operation O O O CUr A108 [Output current] Displays the output current to the motor. - - rpm A109 [Motor RPM] Displays the number of Motor RPM. - - A10A [Inverter DC dcl link voltage] [User display vol A10B select] 1) This function can be available with ig5a Communication Option Module. Displays DC link voltage inside the inverter. This parameter displays the item selected at H73- [Monitoring item select]. vol Output voltage POr Output power tor Torque - - vol - 25

26 ig5a Function List Drive Group LED display non drc drv2 1) Frq2 ref 2) 2) Fbk Address for communication A10C Parameter name [Fault Display] [Direction of Min/Max range A10D motor rotation F, r select] A10E [Drive mode 2] 0 ~ 3 [Frequency A10F setting 0 ~ 7 A110 A111 method 2] PID control standard or 0~400[Hz] value setting 0~100 [%] PID control feedback amount 1) Only displayed when one of the Multi-function input terminals 1-8 [I17~I24] is set to 22. 2) It is indicated when H49(PID control selection) is 1. 3) This function can be available with ig5a Communication Option Module. Displays the types of faults, frequency and operating status at the time of the fault Sets the direction of motor rotation when drv - [Drive mode] is set to either 0 or 1. F Forward r Reverse 0 Run/Stop via Run/Stop key on the keypad FX: Motor forward run 1 RX: Motor reverse run Terminal operation FX: Run/Stop enable 2 RX: Reverse rotation select 3 RS-485 communication 4 Set to Filed Bus Communication 3) 0 Keypad setting 1 Digital 1 Keypad setting 2 2 V1 1: -10 ~ +10 [V] 3 V1 2: 0 ~ +10 [V] 4 Analog Terminal I: 0 ~ 20 [ma] 5 Terminal V1 setting 1 + Terminal I 6 Terminal V1 setting 2+ Terminal I 7 RS485 communication 8 Digital Volume 9 Set to Filed Bus Communication 3) If H58 is 0, it is expressed as a [Hz] unit. If H58 is 1, it is expressed as a [%] unit. In [Hz] unit, you can t set Max. frequency more than (F21). In [%] unit, 100% means Max. frequency. It indicates a feedback amount in PID control. If H58 is 0, it is expressed as a [Hz] unit. If H58 is 1, it is expressed as a [%] unit. Factory defaults - - F Adj. during run O Function group 1 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run F 0 A200 [Jump code] 0 ~ 71 Sets the parameter code number to jump. 1 O F 1 [Forward/ A201 Reverse run 0 ~ 2 disable] 0 Fwd and rev run enable 1 Forward run disable 2 Reverse run disable F 2 F 3 A202 A203 [Accel pattern] [Decel pattern] 0 ~ 1 0 Linear 1 S-curve 26

27 Compact & Powerful Inverter ig5a Function group 1 LED display F 4 F 8 1) F 9 F10 F11 F12 F13 F14 F20 F21 2) F22 F23 F24 3) F25 F26 F27 F28 F29 Address for communication A204 A208 A209 A20A A20B A20C A20D A20E A214 A215 A216 A217 A218 A219 A21A A21B A21C A21D Parameter name [Stop mode select] Min/Max range 0 ~ 3 [DC Brake 0.1 ~ 60 start frequency] [Hz] [DC Brake 0 ~ 60 wait time] [sec] [DC Brake 0 ~ 200 voltage] [%] [DC Brake time] 0 ~ 60 [sec] [DC Brake start 0 ~ 200 voltage] [%] [DC Brake start 0 ~ 60 time] [sec] [Time for 0 ~ 60 magnetizing [sec] a motor] [Jog frequency] 0 ~ 400 [Hz] [Max frequency] 40 ~ 400 [Hz] [Base frequency] 30 ~ 400 [Hz] [Start frequency] 0.1 ~ 10 [Hz] [Frequency high /low limit select] 0 ~ 1 [Frequency 0 ~ 400 high limit] [Hz] [Frequency 0.1 ~ 400 low limit] [Hz] [Torque Boost 0 ~ 1 select] [Torque boost in forward direction] 0 ~ 15 [Torque boost [%] in reverse direction] 1) Only displayed when F 4 is set to 1 (DC brake to stop). 2) If H40 is set to 3 (Sensorless vector), Max. frequency is settable up to 300Hz. 3) Only displayed when F24 (Frequency high/low limit select) is set to 1. 0 Decelerate to stop 1 DC brake to stop 2 Free run to stop 3 Power Braking stop This parameter sets DC brake start frequency. It cannot be set below F23 - [Start frequency]. When DC brake frequency is reached, the inverter holds the output for the setting time before starting DC brake. This parameter sets the amount of DC voltage applied to a motor. It is set in percent of H33 - [Motor rated current]. This parameter sets the time taken to apply DC current to a motor while motor is at a stop. This parameter sets the amount of DC voltage before a motor starts to run. It is set in percent of H33 - [Motor rated current]. DC voltage is applied to the motor for DC Brake start time before motor accelerates. This parameter applies the current to a motor for the set time before motor accelerates during Sensorless vector control. This parameter sets the frequency for Jog operation. It cannot be set above F21 - [Max frequency]. This parameter sets the highest frequency the inverter can output. It is frequency reference for Accel/Decel (See H70) Caution Any frequency cannot be set above Max frequency except Base frequency The inverter outputs its rated voltage to the motor at this frequency (see motor nameplate). The inverter starts to output its voltage at this frequency. It is the frequency low limit. This parameter sets high and low limit of run frequency. This parameter sets high limit of the run frequency. It cannot be set above F21 - [Max frequency]. This parameter sets low limit of the run frequency. It cannot be set above F25 - [Frequency high limit] and below F23 - [Start frequency]. 0 Manual torque boost 1 Auto torque boost This parameter sets the amount of torque boost applied to a motor during forward run. It is set in percent of Max output voltage. This parameter sets the amount of torque boost applied to a motor during reverse run. It is set as a percent of Max output voltage. Factory defaults Adj. during run O

28 ig5a Function List Function group 1 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run 0 {Linear} F30 F31 1) F32 F33 F34 F35 F36 F37 F38 F39 F40 F50 F51 2) F52 F53 A21E [V/F pattern] 0 ~ 2 A21F A220 A221 A222 A223 A224 A225 A226 A227 A228 A232 A233 A234 A235 [User V/F 0 ~ 400 frequency 1] [Hz] [User V/F ] 0 ~ 100 voltage 1 [%] [User V/F 0 ~ 400 frequency 2] [Hz] [User V/F 0 ~ 100 voltage 2] [%] [User V/F 0 ~ 400 frequency 3] [Hz] [User V/F 0 ~ 100 voltage 3] [%] [User V/F 0 ~ 400 frequency 4] [Hz] [User V/F 0 ~ 100 voltage 4] [%] [Output voltage 40 ~ 110 adjustment] [%] [Energy-saving 0 ~ 30 level] [%] [Electronic thermal select] 0 ~ 1 [Electronic thermal level for 1 minute] [Electronic thermal level for continuous] [Motor cooling method] 50 ~ 200 [%] 50 ~ 150 [%] 0 ~ 1 1 {Square} 2 {User V/F} It is used only when V/F pattern is set to 2(User V/F) It cannot be set above F21 - [Max frequency]. The value of voltage is set in percent of H70 - [Motor rated voltage]. The values of the lower-numbered parameters cannot be set above those of higher-numbered. This parameter adjusts the amount of output voltage. The set value is the percentage of input voltage. This parameter decreases output voltage according to load status. This parameter is activated when the motor is overheated (timeinverse). This parameter sets max current capable of flowing to the motor continuously for 1 minute. The set value is the percentage of H33 - [Motor rated current]. It cannot be set below F52 - [Electronic thermal level for continuous]. This parameter sets the amount of current to keep the motor running continuously. It cannot be set higher than F51 - [Electronic thermal level for 1 minute]. Standard motor having cooling fan directly connected to 0 the shaft 1 A motor using a separate motor to power a cooling fan F54 F55 A236 A237 1) Set F30 to 2(User V/F) to display this parameter. 2) Set F50 to 1 to display this parameter. [Overload 30 ~ 150 warning level] [%] [Overload 0 ~ 30 warning time] [Sec] This parameter sets the amount of current to issue an alarm signal at a relay or multi-function output terminal (see I54, I55). The set value is the percentage of H33- [Motor rated current]. This parameter issues an alarm signal when the current greater than F54- [Overload warning level] flows to the motor for F55- [Overload warning time]

29 Compact & Powerful Inverter ig5a Function group 1 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run F56 F57 F58 F59 F60 F61 1) F63 F64 2) F65 F66 F70 A238 A239 A23A A23B A23C A23D A23F A240 A241 A242 A246 [Overload trip select] 0 ~ 1 [Overload 30 ~ 200 trip level] [%] [Overload 0 ~ 60 trip time] [Sec] [Stall prevention select] 0 ~ 7 [Stall prevention 30 ~ 200 level] [%] [When Stall prevention during deceleration, voltage limit select [Save up/down frequency select] [Save up/down frequency] [Up-down mode select] 0~1 0 ~ 1 0~2 [Up-down step 0~400 frequency] [Hz] [Draw run mode select] 0~3 This parameter turns off the inverter output when motor is overloaded. This parameter sets the amount of overload current. The value is the percentage of H33- [Motor rated current]. This parameter turns off the inverter output when the F57- [Overload trip level] of current flows to the motor for F58- [Overload trip time]. This parameter stops accelerating during acceleration, decelerating during constant speed run and stops decelerating during deceleration. During Decel During constant run During Accel Bit 2 Bit 1 Bit This parameter sets the amount of current to activate stall prevention function during Accel, Constant or Decel run. The set value is the percentage of the H33- [Motor rated current]. In Stall prevention run during deceleration, if you want to limit output voltage, select 1 This parameter decides whether to save the specified frequency during up/down operation. When 1 is selected, the up/down frequency is saved in F64. If Save up/down frequency is selected at F63, this parameter saves the frequency before the inverter stops or decelerated. We can select up-down mode among three thing 0 Increases goal frequency as a standard of Max. frequency/min. frequency 1 Increases as many as step frequency according to edge input 2 Available to combine 1 and 2 In case of choosing F65 as a 1 or 2, it means increase or decrease of frequency according to up-down input 0 Inverter doesn t run as a draw mode 1 V1(0~10V) input draw run 2 I(0~20mA) input draw run 3 V1(-10~10V) input draw run F71 A247 [Draw rate] 0~100[%] Sets rate of draw ) It is indicated when setting bit 2 of F59 as 1 2) Set F63 to 1 to display this parameter. 29

30 ig5a Function List Function group 2 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run H 0 A300 [Jump code] 0~95 Sets the code number to jump. 1 O H 1 A301 [Fault history 1] - non - H 2 A302 [Fault history 2] - Stores information on the types of faults, the frequency, the non - H 3 A303 [Fault history 3] - current and the Accel/Decel condition at the time of fault. The non - H 4 A304 [Fault history 4] - latest fault is automatically stored in the H 1- [Fault history 1]. non - H 5 A305 [Fault history 5] - non - H 6 A306 [Reset fault history] 0~1 Clears the fault history saved in H O When run frequency is issued, motor starts to accelerate after H 7 A307 [Dwell frequency] 0.1~400 [Hz] dwell frequency is applied to the motor during H8- [Dwell time]. [Dwell frequency] can be set within the range of F21- [Max 5.0 frequency] and F23- [Start frequency]. H 8 A308 [Dwell time] 0~10 [sec] Sets the time for dwell operation. 0. H10 A30A [Skip frequency 0 ~ 1 select] H11 1) A30B [Skip frequency low limit 1] H12 A30C [Skip frequency high limit 1] H13 A30D [Skip frequency low limit 2] 0.1~400 H14 A30E [Skip frequency [Hz] high limit 2] H15 A30F [Skip frequency low limit 3] H16 A310 [Skip frequency high limit 3] H17 A311 [S-Curve accel/ 1~100 decel start side] [%] H18 A312 [S-Curve accel/ 1~100 decel end side] [%] [Input/output H19 A313 phase loss 0 ~ 3 protection select] H20 A314 [Power On Start select] 0 ~ 1 [Restart after H21 A315 fault reset 0 ~1 selection] 1) only displayed when H10 is set to 1. # H17, H18 are used when F2, F3 are set to 1 (S-curve) Sets the frequency range to skip to prevent undesirable resonance and vibration on the structure of the machine. Run frequency cannot be set within the range of H11 thru H16. The frequency values of the low numbered parameters cannot be set above those of the high numbered ones. Settable within the range of F21 and F23. Set the speed reference value to form a curve at the start during accel/decel. If it is set higher, linear zone gets smaller. Set the speed reference value to form a curve at the end during accel/decel. If it is set higher, linear zone gets smaller. 0 Disabled 1 Output phase protection Input phase Input/output phase 2 3 protection protection This parameter is activated when drv is set to 1 or 2 (Run/Stop via Control terminal). Motor starts acceleration after AC power is applied while FX or RX terminal is ON. This parameter is activated when drv is set to 1 or 2 (Run/Stop via Control terminal). Motor accelerates after the fault condition is reset while the FX or RX terminal is ON O 0 O 0 O 30

31 Compact & Powerful Inverter ig5a Function group 2 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run This parameter is active to prevent any possible fault when the 0 O inverter outputs its voltage to the running motor. 1. H20-2. Restart 3. Operation 4. Normal [Power after instant after fault accel On start] power failure H20-2. Restart 3. Operation 4. Normal [Power after instant after fault accel H22 1) A316 [Speed Search Select] 0 ~ 15 On start] power failure Bit 3 Bit 2 Bit 1 Bit H23 A317 [Current level during Speed search] 80~200 [%] This parameter limits the amount of current during speed search. The set value is the percentage of the H33- [Motor rated current]. 100 O H24 A318 [P gain during Speed search] 0~9999 It is the Proportional gain used for Speed Search PI controller. 100 O H25 A319 [I gain during speed search] 0~9999 It is the Integral gain used for Speed search PI controller. 200 O This parameter sets the number of restart tries after a fault H26 A31A [Number of Auto Restart try] 0 ~10 occurs. Auto Restart is deactivated if the fault outnumbers the restart tries. This function is active when [drv] is set to 1 or 2 {Run/Stop via control terminal}. Deactivated during active 0 O protection function (OHT, LVT, EXT, HWT etc.). H27 A31B [Auto Restart 0~60 time] [sec] This parameter sets the time between restart tries. 1.0 O H30 A31E [Motor type select] 0.2~ kW ~ ~ kW 7.5 2) H31 A31F [Number of motor poles] 2 ~ 12 This setting is displayed via rpm in drive group. 4 1) Normal acceleration has first priority. Even though #4 is selected along with other bits, Inverter performs Speed search #4. 2) H30 is preset based on inverter rating. 31

32 ig5a Function List Function group 2 LED display Address for communication Parameter name Min/Max range Factory defaults Adj. during run H32 A320 [Rated slip 0 ~ 10 frequency] [Hz] rpm p fs = fr -[ 120 ] Where, fs = Rated slip frequency fr = Rated frequency rpm = Motor nameplate RPM p = Number of Motor poles ) H33 H34 H36 H37 H39 H40 H41 H42 H44 H45 2) H46 H47 H48 H49 A321 A322 A324 [Motor rated 0.5~150 current] 1) H32 ~ H36 factory default values are set based on OTIS-LG motor. 2) Set H40 to 3 (Sensorless vector control) to display this parameter. [A] [No Load Motor 0.1~ 50 Current] [Motor efficiency] [A] 50~100 [%] A325 [Load inertia rate] 0 ~ 2 A327 A328 [Carrier frequency select] [Control mode select] 1 ~ 15 [khz] 0 ~ 3 A329 [Auto tuning] 0 ~ 1 A32A A32C A32D A32E A32F A330 [Stator resistance 0 ~ 28 (Rs)] [Ϊ] [Leakage 0~ inductance (Lσ)] [Sensorless P gain] [Sensorless I gain] [Sensorless 100~220 [mh] 0~ torque limit] [%] PWM mode select 0~1 A331 PID select 0~1 Enter motor rated current on the nameplate. Enter the current value detected when the motor is rotating in rated rpm after the load connected to the motor shaft is removed. Enter the 50% of the rated current value when it is difficult to measure H34 - [No Load Motor Current]. Enter the motor efficiency (see motor nameplate). Select one of the following according to motor inertia. 0 Less than 10 times 1 About 10 times 2 More than 10 times This parameter affects the audible sound of the motor, noise emission from the inverter, inverter temp, and leakage current. If the set value is higher, the inverter sound is quieter but the noise from the inverter and leakage current will become greater. 0 {Volts/frequency Control} 1 {Slip compensation control} 3 {Sensorless vector control} If this parameter is set to 1, it automatically measures parameters of the H42 and H44. This is the value of the motor stator resistance. This is leakage inductance of the stator and rotor of the motor. P gain for Sensorless control I gain for Sensorless control Limits output torque in sensorless mode. If you want to limit a inverter leakage current, select 2 phase PWM mode. It has more noise in comparison to Normal PWM mode. 0 Normal PWM mode 1 2 phase PWM mode Selects whether using PID control or not O O 100 O

33 Compact & Powerful Inverter ig5a Function group 2 LED display H50 1) H51 H52 H53 H54 H55 H56 H57 H58 H60 H61 2) H62 H63 H64 H65 H66 H67 H70 Address for communication Parameter name Min/Max range A332 [PID F/B select] 0 ~ 1 A333 A334 A335 A336 A337 A338 A339 A33A A33C [P gain for PID] 0~ [%] [Integral time 0.1~32.0 for PID [sec] [Differential time 0 ~ 30.0 for PID (D gain)] [PID control mode select] [PID output frequency high limit] [PID output frequency low limit] [PID standard value select] PID control unit select [Self-diagnostic select] [sec] 0~1 0.1 ~ 400 [Hz] 0.1 ~ 400 [Hz] 0~4 0~1 0 ~ 3 A33D [Sleep delay time] 0~2000[s] A33E [Sleep frequency] 0~400[Hz] A33F [Wake up level] 0~100[%] A340 [KEB drive select] 0~1 A341 [KEB action 110~140 start level] [%] A342 [KEB action 110~145 stop level] [%] A343 [KEB action gain] 1~20000 [Frequency A346 Reference for 0 ~ 1 Accel/Decel] 0 Terminal I input (0 ~ 20 ma) 1 Terminal V1 input (0 ~ 10 V) This parameter sets the gains for the PID controller. Selects PID control mode 0 Normal PID control 1 Process PID control This parameter limits the amount of the output frequency through the PID control. The value is settable within the range of F21? [Max frequency] and F23 - [Start frequency]. Selects PID standard value. Standard value is indicated in ref of Drive group. 0 Loader digital setting 1 1 Loader digital setting 2 2 V1 terminal setting 2: 0~10V 3 I terminal setting: 0~20mA 4 Setting as a RS-485 communication Selects a unit of the standard value or feedback amount. 0 Frequency[Hz] 1 Percentage[%] 0 Self-diagnostic disabled 1 IGBT fault/ground fault 2 Output phase short & open/ Ground fault 3 Ground fault (This setting is unable when more than 11kW) Sets a sleep delay time in PID drive. Sets a sleep frequency when executing a sleep function in PID control drive. You can t set more than Max. frequency(f21) Sets a wake up level in PID control drive. Sets KEB drive. Sets KEB action start level according to level. Sets KEB action stop level according to level. Sets KEB action gain. 0 Based on Max freq (F21) 1 Based on Delta freq. 1) Set H49 to 1 (PID control) to display this parameter. 2) Set H49 as a 1 3): it is indicated when setting H64(KEB drive select) as a 1 (KEB does not operate when cut power after loading ting input (about 10%). Factory defaults Adj. during run O 1.0 O 0.0 O O 0.50 O O 35.0 O

34 ig5a Function List Function group 2 LED display H71 H72 H73 H74 H75 H76 H77 1) H78 H79 Address for communication A347 A348 A349 A34A Parameter name [Accel/Decel time scale] [Power on display] [Monitoring item select] Min/Max range 0 ~ 2 0 ~ 15 0 ~ 2 [Gain for Motor 1 ~ 1000 rpm display] [%] [DB resistor A34B operating rate 0 ~ 1 A34C A34D A34E limit select] [DB resistor 0 ~ 30 operating rate] [%] [Cooling fan control] [Operating method select when cooling fan malfunctions] 0 ~ 1 0 ~ 1 A34F [S/W version] 0 ~ ) Exception: Since SV004iG5A-2/SV004iG5A-4 is Natural convection type, this code is hidden. 0 Settable unit: 0.01 second. 1 Settable unit: 0.1 second. 2 Settable unit: 1 second. This parameter selects the parameter to be displayed on the keypad when the input power is first applied. 0 Frequency command 1 Accel time 2 Decel time 3 Drive mode 4 Frequency mode 5 Multi-Step frequency 1 6 Multi-Step frequency 2 7 Multi-Step frequency 3 8 Output current 9 Motor rpm 10 Inverter DC link voltage 11 User display select (H73) 12 Fault display 13 Direction of motor rotation select 14 Output current 2 15 Motor rpm 2 16 Inverter DC link voltage 2 17 User display select 2 One of the following can be monitored via vol - [User display select]. 0 Output voltage [V] 1 Output power [kw] 2 Torque [kgf m] This parameter is used to change the motor rotating speed (r/min) to mechanical speed (m/mi) and display it. 0 Unlimited 1 Use DB resistor for the H76 set time. Set the percent of DB resistor operating rate to be activated during one sequence of operation. 0 Always ON Keeps ON when its temp is higher than inverter protection 1 limit temp. Activated only during operation when its temp is below that of inverter protection limit. 0 Continuous operation when cooling fan malfunctions. 1 Operation stopped when cooling fan malfunctions. This parameter displays the inverter software version. Factory defaults Adj. during run 1 O 0 O 0 O 100 O 1 O 10 O 0 O 0 O 1. 34

35 Compact & Powerful Inverter ig5a Function group 2 LED display H81 1) H82 H83 H84 H85 H86 H87 H88 H89 H90 H91 2) H92 H93 H94 H95 Address for communication A351 A352 A353 A354 A355 A356 A347 A358 A359 A35A Parameter name [2 nd motor Min/Max range Accel time] 0 ~ 6000 [2 nd motor [sec] Decel time] [2 nd motor 30 ~ 400 base frequency] [2 nd motor V/F pattern] [2 nd motor forward [Hz] 0 ~ 2 torque boost] 0 ~ 15 [2 nd motor reverse [%] torque boost] [2 nd motor stall 30~150 prevention level] [%] [2 nd motor Electronic thermal level for 1 min] [2 nd motor 50~200 [%] Electronic 50~150 thermal level for [%] continuous] [2 nd motor 0.1~100 rated current] 1) It is indicated when choosing I17~I24 as a 12 (2nd motor select). 2) H91,H92 parameters are displayed when Remote option is installed. [A] A35B [Parameter read] 0 ~ 1 A35C [Parameter write] 0 ~ 1 A35D A35E [Parameter initialize] [Password register] 0 ~ 5 0 ~ FFFF A35F [Parameter lock] 0 ~ FFFF This parameter actives when the selected terminal is ON after I17-I24 is set to 12 {2 nd motor select}. Copy the parameters from inverter and save them into remote loader. Copy the parameters from remote loader and save them into inverter. This parameter is used to initialize parameters back to the factory default value. 0 - All parameter groups are initialized to factory default 1 value. 2 Only Drive group is initialized. 3 Only Function group 1 is initialized. 4 Only Function group 2 is initialized. 5 Only I/O group is initialized. Password for H95-[Parameter lock]. Set as Hexa value. This parameter is able to lock or unlock parameters by typing password registered in H94. UL (Unlock) Parameter change enable L (Lock) Parameter change disable Factory defaults Adj. during run 5.0 O 10.0 O O 100 O O 0 O 35

36 ig5a Function List Input/output group LED display I 0 I 2 I 3 I 4 I 5 I 6 I 7 I 8 I 9 I10 I11 I12 I13 I14 I15 I16 I17 I18 I19 I20 Address for communication Parameter name Min/Max range A400 [Jump code] 0 ~ 87 A402 [NV input 0 ~ -10 Min voltage] [V] A403 [Frequency 0 ~ 400 corresponding to I 2] [Hz] A404 [NV input 0 ~ -10 Max voltage] [V] A405 [Frequency 0 ~ 400 corresponding to I 4] [Hz] A406 [Filter time constant 0 ~ 9999 for V1 input] A407 [V1 input Min 0 ~ 10 voltage] [V] A408 [Frequency 0 ~ 400 corresponding to I 7] [Hz] A409 [V1 input Max 0 ~ 10 voltage] [V] A40A [Frequency 0 ~ 400 corresponding to I 9] [Hz] A40B [Filter time constant for I input] 0 ~ 9999 A40C [I input Min 0 ~ 20 current] [ma] A40D [Frequency 0 ~ 400 corresponding to I 12] [Hz] A40E [I input Max 0 ~ 20 current] [ma] A40F [Frequency 0 ~ 400 corresponding to I 14] [Hz] [Criteria for A410 Analog Input 0 ~ 2 Signal loss] [Multi-function A411 input terminal P1 define] [Multi-function A412 input terminal P2 define] [Multi-function 0 ~ 27 A413 input terminal P3 define] [Multi-function A414 input terminal P4 define] * See Chapter 14 Troubleshooting and maintenance ± for External trip A/B contact. * Each multi-function input terminal must be set differently. Sets the code number to jump. Sets the minimum voltage of the NV (-10V~0V) input. Sets the inverter output minimum frequency at minimum voltage of the NV input. Sets the maximum voltage of the NV input. Sets the inverter output maximum frequency at maximum voltage of the NV input. Adjusts the responsiveness of V1 input (0 ~ +10V). Sets the minimum voltage of the V1 input. Sets the inverter output minimum frequency at minimum voltage of the V1 input. Sets the maximum voltage of the V1 input. Sets the inverter output maximum frequency at maximum voltage of the V1 input. Sets the input section s internal filter constant for I input. Sets the minimum current of I input. Sets the inverter output minimum frequency at minimum current of I input. Sets the Maximum current of I input. Sets the inverter output maximum frequency at maximum current of I input. 0 Disabled 1 activated below half of set value. 2 activated below set value. 0 Forward run command 1 Reverse run command 2 Emergency Stop Trip 3 Reset when a fault occurs {RST} 4 Jog operation command 5 Multi-Step freq - Low 6 Multi-Step freq - Mid 7 Multi-Step freq - High Factory defaults Adj. during run 1 O 0.00 O 0.00 O 10.0 O O 10 O 0 O 0.00 O 10 O O 10 O 4.00 O 0.00 O O O 0 O 0 O 1 O 2 O 3 O 36