VFD - D700 Series Specifications. The latest low-cost variable speed control solution for centrifugal pumps.

Transcription

1 VFD - D700 Series Specifications The latest low-cost variable speed control solution for centrifugal pumps. Built-in PID Control to maintain pressure, flow, measured value, and much more 125% overload protection for 130 seconds, 150% overload protection for 60 seconds, 200% overload protection for 3 seconds, Available in single-phase 115V supply power up to 1HP Available in single-phase 240V supply power up to 3HP Available in three-phase 240V and 480V supply power up to 10HP Internal power supply: 24VDC up to 100mA General-purpose Magnetic Flux Vector Control for improved starting torque and smooth low speed motor operation frequency range of 0.2 to 400Hz Standard RS485 serial communications supporting Modbus RTU Password protected for Read & Write Supports remote I/O function via network Delivers rated current at 50 C and 14.5kHz carrier frequency with minimal de-rating 0 to 10V analog output Standard 5-year warranty D700 Selection & Dimensions Amps HP Model Number Dimensions in inches (mm) Height Width Depth Weight Lbs (kg) Stock 1-Phase 100~120VAC / 3-Phase VAC 0.8 1/8 FR-D710W-008-NA 5.0 (128) 2.7 (68) 3.2 (81) 1.1 (0.5) S 1.4 1/4 FR-D710W-014-NA 5.0 (128) 2.7 (68) 4.4 (113) 1.3 (0.6) S 2.5 1/2 FR-D710W-025-NA 5.0 (128) 2.7 (68) 5.6 (143) 2.0 (0.9) S FR-D710W-042-NA 5.0 (128) 6.7 (170) 5.9 (150) 3.8 (1.7) S

2 Amps HP Model Number Dimensions in inches (mm) Height Width Depth Weight Lbs (kg) Stock 1-Phase 200~240VAC / 3-Phase VAC 0.8 1/8 FR-D720S-008-NA 5.0 (128) 2.7 (68) 3.2 (81) 1.1 (0.5) S 1.4 1/4 FR-D720S-014-NA 5.0 (128) 2.7 (68) 3.2 (81) 1.3 (0.6) S 2.5 1/2 FR-D720S-025-NA 5.0 (128) 2.7 (68) 5.6 (143) 2.0 (0.9) S FR-D720S-042-NA 5.0 (128) 2.7 (68) 6.5 (163) 2.5 (1.1) S FR-D720S-070-NA 5.0 (128) 4.3 (108) 6.2 (156) 3.3 (1.5) S 10 3 FR-D720S-100-NA 5.9 (150) 5.5 (140) 5.7 (145) 4.2 (1.9) S 3-Phase 200~240VAC & 0.8 1/8 FR-D NA 5.0 (128) 2.7 (68) 3.2 (81) 1.1 (0.5) S 1.4 1/4 FR-D NA 5.0 (128) 2.7 (68) 3.2 (81) 1.1 (0.5) S 2.5 1/2 FR-D NA 5.0 (128) 2.7 (68) 4.4 (113) 1.8 (0.8) S FR-D NA 5.0 (128) 2.7 (68) 5.2 (133) 2.2 (1.0) S FR-D NA 5.0 (128) 4.3 (108) 5.3 (136) 3.1 (1.4) S 10 3 FR-D NA 5.0 (128) 4.3 (108) 5.3 (136) 3.1 (1.4) S FR-D NA 5.0 (128) 6.7 (170) 5.6 (143) 3.8 (1.7) S /2 FR-D NA 5.9 (150) 8.7 (220) 6.1 (155) 7.5 (3.4) S FR-D NA 5.9 (150) 8.7 (220) 6.1 (155) 7.5 (3.4) S 3-Phase 380~480VAC & 1.2 1/2 FR-D NA 5.0 (128) 4.3 (108) 5.1 (130) 2.7 (1.2) S FR-D NA 5.0 (128) 4.3 (108) 5.1 (130) 2.7 (1.2) S FR-D NA 5.0 (128) 4.3 (108) 5.4 (136) 2.9 (1.3) S 5 3 FR-D NA 5.0 (128) 4.3 (108) 6.2 (156) 3.1 (1.4) S 8 5 FR-D NA 5.0 (128) 4.3 (108) 6.6 (166) 3.3 (1.5) S /2 FR-D NA 5.9 (150) 8.7 (220) 6.1 (155) 6.9 (3.1) S FR-D NA 5.9 (150) 8.7 (220) 6.1 (155) 6.9 (3.1) S

3 D700 Series General Specifications Control Method Frequency Range Soft-PWM control/high carrier frequency PWM control (V/F control, general-purpose magnetic flux vector control, optimum excitation control can be selected) 0.2 to 400Hz Frequency Setting Resolution Analog Digital 0.06Hz/60Hz (terminal2, 4: 0 to 10V/10bit) 0.12Hz/60Hz (terminal2, 4: 0 to 5V/9bit) 0.06Hz/60Hz (terminal4: 4 to 20mA/10bit) 0.01Hz Control Specifications Frequency Accuracy Voltage/Frequency Characteristics Starting Torque Analog Digital Within ±1% of the max. output frequency (25 C ±10 C) Within 0.01% of the set output frequency Base frequency can be set from 0 to 400Hz Constant torque/variable torque pattern can be selected 150% or more (at 1Hz) when general-purpose magnetic flux vector control and slip compensation is set Torque Boost Acceleration/Deceleration Time Setting DC Injection Brake Stall Prevention Operation Level Manual torque boost 0.1 to 3600s (acceleration and deceleration can be set individually), linear or S-pattern acceleration/deceleration mode can be selected. Operation frequency (0 to 120Hz), operation time (0 to 10s), operation voltage (0 to 30%) variable Operation current level can be set (0 to 200% adjustable), whether to use the function or not can be selected Operation Specifications Frequency Setting Signal Start Signal Signal Analog Digital Two points Terminal 2: 0 to 10V, 0 to 5V can be selected Terminal 4: 0 to 10V, 0 to 5V, 4 to 20mA can be selected Entered from operation panel and parameter unit. Frequency setting increments is selectable Forward and reverse rotation or start signal automatic self-holding input (3-wire input) can be selected. Five points You can select from among multi-speed selection, remote setting, second function selection, terminal 4 input selection, JOG operation selection, PID control valid terminal, external thermal input, PUexternal operation switchover, V/F switchover, output stop, start

4 self-holding selection, traverse function selection, forward rotation, reverse rotation command, inverter reset, PU-NET operation switchover, external-net operation switchover, command source switchover, inverter operation enable signal, and PU operation external interlock Operational Functions Maximum/minimum frequency setting, frequency jump operation, external thermal relay input selection, automatic restart after instantaneous power failure operation, forward/reverse rotation prevention, remote setting, second function, multi-speed operation, regeneration avoidance, slip compensation, operation mode selection, offline auto tuning function, PID control, computer link operation (RS-485), optimum excitation control, power failure stop, speed smoothing control, Modbus-RTU Signal Points Open Collector Relay One point One point Signal Operating Status For Meter Points Pulse You can select from among inverter operation, up-to-frequency, overload alarm, output frequency detection, regenerative brake prealarm, electronic thermal relay function pre-alarm, inverter operation ready, output current detection, zero current detection, PID lower limit, PID upper limit, PID forward/reverse rotation output, brake opening request, fan alarm*2, heatsink overheat prealarm, deceleration at an instantaneous power failure, PID control activated, PID output interruption, during retry, life alarm, current average value monitor, remote output, alarm output, fault output, fault output 3, and maintenance timer alarm MAX 2.4kHz: one point For Meter You can select from among output frequency, motor current (steady), output voltage, frequency setting, converter output voltage, regenerative brake duty, electronic thermal relay function load factor, output current peak value, converter output voltage peak value, reference voltage output, motor load factor, PID set point, PID measured value, output power, PID deviation, motor thermal load factor, inverter thermal load factor, pulse train output (1440 pulses/full scale) Indication Operation Panel Parameter Unit (FR- PU07) Operating Status You can select from among output frequency, motor current (steady), output voltage, frequency setting, cumulative energization time, actual operation time, converter output voltage, regenerative brake duty, electronic thermal relay function load factor, output current peak value, converter output voltage peak value, motor load factor, PID set point, PID measured value, PID deviation, inverter I/O terminal monitor, output power, cumulative power, motor thermal load factor, and inverter thermal load factor, PTC thermistor resistance

5 Additional Display By The Parameter Unit (FR- PU04/FR- PU07) Only Fault Definition Operating Status Fault Definition Interactive Guidance Fault definition is displayed when the fault occurs and the past 8 fault definitions (output voltage/current/frequency/cumulative energization time right before the fault occurs) are stored Not used voltage/current/frequency/cumulative energization time immediately before the fault occurs Function (help) for operation guide Protective & Warning Function Ambient Temperature Protective functions Overcurrent during acceleration, overcurrent during constant speed, overcurrent during deceleration, overvoltage during acceleration, overvoltage during constant speed, overvoltage during deceleration, inverter protection thermal operation, motor protection thermal operation, heatsink overheat, input phase failure (*4 *5), output side earth (ground) fault overcurrent at start (*4), output phase failure, external thermal relay operation (*4), PTC thermistor operation (*4), parameter error, PU disconnection, retry count excess (*4), CPU fault, brake transistor alarm, inrush resistance overheat, analog input error, stall prevention operation, output current detection value exceeded Warning functions Fan alarm (*2), overcurrent stall prevention, overvoltage stall prevention, PU stop, parameter write error, regenerative brake prealarm (*4), electronic thermal relay function pre-alarm, maintenance output (*4), undervoltage, operation panel lock, password locked, inverter reset -10 C to +50 C (14 F to 122 F) (non-freezing), -10 C to +40 C (14 F to 104 F) for totally-enclosed structure feature (*3) Environment Ambient Humidity Storage Temperature (*1) Atmosphere 90%RH maximum (non-condensing) -20 C to +65 C (-4 F to 149 F) Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt etc.) Altitude/Vibration Maximum 1000m ( feet) above sea level, 5.9m/s 2 or less Notes: *1. Temperatures applicable for a short time, e.g. in transit. *2. As the 0.75K or less is not provided with the cooling fan, this alarm does not function. *3. When using the inverters at the ambient temperature of 40 C (104 F) or less, the inverters can be installed closely attached (0cm clearance). *4. This protective function does not function in the initial status. *5. This protective function is available with the three-phase power input specification model only.

6 Terminal Connection Diagram Three Phase 200V power input Three Phase 400V power input Single Phase 115V power input Single Phase 200V power input