SELEKTA SELEKTA 170 top2 D GB F I E P NL PL. Installation and Operating Manual Digital astronomic time switch. SELEKTA 170 top2
|
|
- Gyles Page
- 5 years ago
- Views:
Transcription
1 SELEKTA SELEKTA 170 top ,5mm - L N V~ Installation and Operating Manual Digital astronomic time switch MENU SELEKTA 170 top2 D F I E P NL PL SELEKTA 170 top2 Correct connection required for smooth zero crossing switch operation (see connection diagram)!
2 Contents Basic safety instructions 3 Display and keys/operating instructions 4 Overview of menu selection 5 Connection/installation 6 Initial start-up 7 Menu item ASTRO Astro times, complete simulation, offset, astromode, position 8 Change position 9 Menu item PROGRAM Set switching time 10 Menu item MANUAL Manual and permanent switching 11 Menu item OPTIONS PIN code 12 Operating hours counter 12 OBELISK top2 memory card 13 Technical data 14 Service address/hotline 14 2
3 Basic safety instructions WARNING Danger of death through electric shock or fire! Installation should only be carried out by a professional electrician! The device is designed for installation on DIN top hat rails (in accordance with EN 60715) Corresponds to type 1 BSTU in accordance with IEC/EN Power reserve (10 years) is reduced if memory card is inserted (in battery operation) OBELISK top2 memory card: Avoid mechanical stress or contamination caused by other storage/ transport methods Designated use The astronomic timer is used for lighting equipment (roads), external staircases, shop windows, entrances etc. For use only in closed, dry rooms Disposal Dispose of equipment in an environmentally-friendly manner 3
4 Screen display and keys Operating instructions Programmed ON times Date display Sunrise/sunset display 1. Read text lines Flashing text/symbol is a prompt Channel status ON = On OFF = Off Time display Days of the week from 1 to 7 Display of active keys with relevant function 2. Make a decision MENU Activate screen Open menu Cancel menu ESC (leave menu) Selection options are displayed Confirm selection Confirm selection YES Confirmation press NO Change/ select press 4
5 Overview of menu selection OFF 9:40 46 ASTRO PROGRAM TIME/DATE MANUAL OPTIONS ASTRO TIMES NEW TIME PERMANENT ON OPERATING HOURS METER COMPLETE SIMULATION CHECK DATE PERMANENT OFF LCD ILLUMINA- TION OFFSET CHANGE SUMMER-- WINTER MANUAL ON LANGUAGE ASTRO MODE DELETE DAY OF THE WEEK TIMER PIN POSITION COMPLETE SIMULATION DATE FORMAT FACTORY SETTING TIME FORMAT INFO 5
6 Connection/installation WARNING Warning, danger of death through electric shock! Must be installed by a professional electrician! Connect power source! Cover or shield any adjacent live components. Ensure device cannot be switched on! Check power supply is disconnected! Earth and bypass! Connect cable Strip cable by 8 mm (max. 9). Insert 45 cable in the open DuoFix screwless terminal (2 cables per terminal position possible). To open the DuoFix screwless terminal, press screwdriver downwards. DuoFix screwless terminal Spring screwless terminal NC contact Test tap 45 cable 6
7 Initial start-up Set language, country, town/city, date, time as well as summer/winter time (SO-WI) Press required key and display follows on screen (see fig). GERMAN KEEP PROGRAM LAND GERMANY STUTTGART ok ok ok ok ok ENGLISH DELETE PRO- GRAM COORDI NATES SPAIN BERLIN SPANISH ESTONIA FRANCE BREMEN DRESDEN DATE FORMAT YEAR MONTH DAY... GREAT BRITAIN... DUESSEL- DORF... TIME FORMAT HOUR MINUTE SUMMER-WIN- TER EUROPE ON 9:
8 ASTRO menu In the ASTRO menu astro times, complete simulation, offset, astromode as well as position (location) can be viewed or changed. Astro times Display of the astro times (including the offsets) for the current day Complete simulation Display of the switching behaviour with a freely selectable Start date (the holiday program is not displayed) Offset The offset (adjustment value) can be used to shift calculated astro times +/ 2 h. This enables the Astro switch-on and switch-off times to be adapted to local circumstances (e.g. mountains, high buildings etc.) or to personal requirements. Astro mode Evenings on, mornings off Switches on at sunset, switches off at sunset (Example: street lighting) Evenings off, mornings on Switches off at sunset, switches on at sunrise (Example: terrarium). Astro inactive The astro times are ineffective (timer function only). Position Location set by selecting a city or by coordinates (latitude/longitude, time zone). The OBELISK top2 memory card allows up to 10 further cities (= favourites) to be entered. 8
9 Change position E.g. enter different country, a different city. Press MENU (see fig.). ASTRO ok ASTRO TIMES COMPLETE SIMULATION OFFSET ASTRO MODE POSITION ok LAND COORDI NATES ok FRANCE SPAIN ESTONIA ok AJACCIO BAYONNE BORDEAUX GERMANY GREAT BRITAIN BREST CAEN
10 Set switching time A timer always consists of a start time and an end time (LASTS UNTIL). (e.g. night switch-off on Monday PROGRAM NEW 23:00 05:00 hrs) ok ok FREE 56 CHECK or Press MENU (see fig.). They have 56 free memory cells available. CHANGE DELETE COMPLETE SIMULATION NIGHT SWITCH-ON HOUR MINUTE MONDAY LASTS UNTIL DAY SWITCH-ON Start time Copy switching to other days of the week. The day of the week always relates to a start time SAVE PLUS TUESDAY COPY SAVE Switching time for one day 10
11 Manual and permanent switching Manual and permanent switching can be set using the menu in MANUAL or (in the automatic screen) by key combination (see fig). Manual control Reversing the channel status to the next automatic or programmed switching. Channel C1 Activate manual switching Briefly press both keys simultaneously. Activate permanent switching Simultaneously press both keys for 2 seconds. Cancelling manual/permanent switching Press both keys simultaneously. Permanent switching As long as a permanent switching (on or off) is activated, the programmed switching times are ineffective. 11
12 PIN code The PIN code is set in OPTIONS via the menu. If you have forgotten your PIN call the Theben Hotline. OPERATING HOURS METER OPTIONS Operating hours counter LCD ILLUMINA- TION LANGUAGE The operating hours of the channel (relay) are displayed and deleted in the OPTIONS menu. If the number of operating hours exceeds the value set in the Service menu, SERVICE will appear in the display. PIN FACTORY SETTING INFO ok WITHOUT PIN WITH PIN ok ok CURRENT PIN NEW PIN Example: replace a light source after 5,000 h. Delete operating hours or increase the value set in service (e.g. to 10,000 h). 12
13 OBELISK top2 memory card Using memory card COPY OBELISK CLOCK COPY CLOCK OBELISK ok COPY PROGRAM COPY ALL DATA Insert memory card in the timer. Request saved switch timings, read to/from the time switch or start the Obelisk program. Remove OBELISK top2 memory card (No ) (optional) after programming etc. and store in cover. START OBELISK PROGRAM... Copy OBELISK CLOCK Copy program: Copies only the switching program. Copy all data: Copies the switching program and all settings (e.g. position, offset, time format etc.). Copy OBELISK CLOCK All switching programs and settings are copied to the memory card. 13
14 4 0,5mm 2 - C1/C2 1 C1 C V UC 0,5mm V UC DATA 0,5mm V UC 4 0,5mm 2 - C1/C2 1 C1 C V UC DATA 0,5mm V UC 4 0,5mm 2 - C1/C2 1 C1 C V UC 0,5mm V UC + Special voltage SELEKTA top2 24 V MENU MENU MENU The technical data and the section on the "electrical connection" of 230 V devices ~ ~ V ~ V ~+ ~+ ~ SELEKTA 170 top2 Ext MENU ~+ ~ ~+ ~ + SELEKTA 171 top2 RC ~ ~ V ~ V ~+ + Ext ~+ ~ ~+ ~ (see operating instructions) do not apply to devices with special voltage. Electrical connection + SELEKTA 171 top2 RC Ext1 MENU Ext SELEKTA172 top2 ~ ~ V ~ V ~+ SELEKTA 170 top2 24 V SELEKTA 171 top2 RC 24 V SELEKTA 172 top2 24 V SELEKTA 170 top2 ~ V ~ Technical data Permissible operating voltage: 12 V 24 V / Hz +10 % 15 %, 12 V 24 V DC +10 % 15 % Switching capacity: 16 A, 250 V~ cos ϕ = 1 Incandescent lamp load, halogen load: 1400 W at 230 V or 6 A Flashlight (EB) 230 V: 180 W Compact lamp (EB) 230 V: 7 x 7 W, 6 x 11 W, 5 x 15 W, 5 x 20 W, 4 x 23 W Fluorescent lamps, parallel-corrected 230 V: 1 x 58 W / 7 µf, 2 x 36 W (4.5 µf each), max. 12 µf Halogen metal halide lamps 230 V: 1 x 70 W (12 µf) Standby output min.: 0.2 W (SELEKTA SELEKTA 172 top2 24 V); 0.8 W (SELEKTA 171 top2 RC 24 V) Power consumption type: 0.6 W (SELEKTA 170 top2 24 V), 1.2 W (SELEKTA 171 top2 RC 24 V); 0.9 W (SELEKTA 172 top2 24 V) Mode of operation: Type 1 BSTU in accordance with EN Pollution degree: 2 Rated impulse voltage: 4 kv Protection class: II for supply with FELV and/or mains switching III for supply with SELV and switching of SELV Protection rating: IP 20 in accordance with EN Power reserve: 10 years at 20 C Ext1 Ext2 MENU 1 2 The devices are designed for switching mains and low voltage (SELV, PELV, FELV). SELEKTA172 top2 SELEKTA 172 top2 24 V Ext1 Ext2 1 2 SELEKTA172 top2 With the SELEKTA 172 top2 24 V the type of low voltage must correspond to low voltage type of the supply voltage (SELV = SELV, PELV = PELV, FELV = FELV). If the switch output is 230 V, the time switch can be operated using low function voltage but not SELV as ~ ~ V V supply ~+ voltage. ~+ Lay the control cable separately from the load power. SELEKTA 170 top2 24 V, SELEKTA 171 top2 RC 24 V The devices are approved for switching SELV and mains voltage. External outputs The external outputs are designed for operating voltage of V AC and DC and not for 230 V. Serviceadresse Theben AG Hohenbergstr Haigerloch DEUTSCHLAND Fon +49 (0) 74 74/ Fax +49 (0) 74 74/ Hotline Fon +49 (0) 74 74/ Fax +49 (0) 74 74/ hotline@theben.de Addresses, telefon numbers etc.
15 Technical data Nominal voltage: V~, +10 %/-15 % Frequency: Hz Gap: <3 mm Power consumption: type 4 VA Contact material: AgSnO 2 Contact: two way switch Switch output: phase-independent (zero-crossover switching) Suitable for switching SELV (Safe Extra-Low Voltage) Switching capacity: 16 A/250 V~ cos ϕ = 1 Switching capacity: 10 A/250 V~ cos ϕ = 0.6 Switching capacity min.: 10 ma/230 V AC 100 ma/12 V AC/DC Glow lamp load: 2600 W Halogen lamp load: 2600 W Fluorescent lamps (VVG low-loss series devices): uncorrected: 2300 VA Series corrected: 2300 VA parallel-corrected: 730 VA (80 µf) Lead-lag circuit (duo): 1000 VA Fluorescent lamps (EVG Electronic series devices): 650 W Mercury and sodium vapour lamps: parallel-corrected: 730 VA (80 µf) 14 Compact fluorescent tubes (EVG): 22x7 W, 18x11 W, 16x15 W, 16x20 W, 14x23 W Permissible ambient temperature: 30 C C Protection class: II in accordance appropriate installation Protection rating: IP 20 in accordance with EN Pollution degree: 2 Service address/hotline Service address Theben AG Hohenbergstr Haigerloch GERMANY Telephone +49 (0) Fax: +49 (0) Hotline Telephone +49 (0) Fax +49 (0) hotline@theben.de Addresses, telephone numbers etc.
Tempus Digital Digital Astro-Timer D GB CZ BZT28A71. Installation and Operating Manual BZT28A71
2 8mm 310366 Tempus Digital Digital Astro-Timer BZT28A71 0,5mm - 2,5mm 2 0 6 12 18 24 L N 230-240V~ 50-60Hz R 10a -30T Installation and Operating Manual MENU OK BTZ28A71 D CZ PL HR 16(10)A 250V~ 1 2 3
More informationTR TR 641 top TR 642 top TR 644 top TR 641 top2 RC TR 642 top2 RC TR 644 top2 RC
2 2 309 429 01 TR TR 641 top2 641 0 100 TR 642 top2 642 0 100 TR 644 top2 644 0 100 TR 641 top2 RC 641 0 300 TR 642 top2 RC 642 0 300 TR 644 top2 RC 644 0 300 Installation and operating instructions Digital
More information*Current connection required for smooth zerocrossing switch operation
2 2 310 317 02 LUNA LUNA 109 109 0 100, 109 0 200 110 0 100, 110 0 200 GB Assembly and operating instructions Twilight Switch Test 2 2000 LUNA 109 I:2-35 II : 35-200 III : 200-1000 min max IV:1-5klx V:
More informationRAMSES 784 HF Set 1. Bedienungsanleitung Uhrenthermostat 1. Operating Instructions Clockthermostat 14. Mode d emploi Thermostat à horloge 26
309 484 01 RAMSES 784 HF Set 1 784 9 407 784 9 417 Bedienungsanleitung Uhrenthermostat 1 Operating Instructions Clockthermostat 14 Mode d emploi Thermostat à horloge 26 Gebruiksaanwijzing Klokthermostaat
More informationE N SHT-1 SHT-1/2 SHT-3 SHT-3/2
Digital time switch E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Content Symbol, Connection... 3 Warning... Characteristics... 5 Technical parameters... 6 Versions of time switches, Load... 7 Description... 8-9 Control...
More informationSentry Digital Timers
Sentry Digital Timers 0733s S4 Contents 1. Safety precautions 2. General rmation 3. DIN rail Installation 4. Display Layout. Programming 6. Technical Data 7. Guarantee 2 Safety precautions The connection
More informationDIN Rail Time & Twilight Switches
DIN Rail & Switches guard Limited, Victory Park, 00 Edgware Road, London NW ND. www.timeguard.com The New Generation of Analogue & Multi-Channel TR top Switches Section Overview Section Overview switches
More informationOPERATING INSTRUCTIONS Digital weekly time switch
OPERATING INSTRUCTIONS Digital weekly time switch 1 Explanation of display and control buttons One-channel timer A B Two-channel timer 1.1 Control buttons i Set time and day of the week e Manual switching
More information4TCD1. Digital 7-Day Programmable Timer. Installation Instructions. Tel Fax Schneider Electric (Australia) Pty Ltd
Digital 7-Day Programmable Timer 4TCD1 Schneider Electric (Australia) Pty Ltd Contact us: clipsal.com/feedback National Customer Care Enquiries: Tel 1300 2025 25 Fax 1300 2025 56 Installation Instructions
More informationTR 612 S. Bedienungsanleitung (Seite 2 19) Operating Instructions (pag ) Mode d emploi (page 38 55) Bruksanvisning (S.
310 415 TR 612 S Bedienungsanleitung (Seite 2 19) Operating Instructions (pag. 20 37) Mode d emploi (page 38 55) Bruksanvisning (S. 56 73) 2-Channel Time Switch EIB 8 GB 7 9 10 6 1 2 11 5 4 3 2 1 1 2 3
More informationTime switches 16 A NEON SЕRIES. Heating and cooling. Shop displays. Lighting for parks. Streetlights and car park lighting.
Heating and cooling NEON Shop displays Lighting for parks SЕRES Streetlights and car park lighting School bells FNDER reserves the right to alter characteristics at any time without notice. FNDER assumes
More informationtheben 4-/8-/12-Channel Switch Module Switch Actuator Modular with Basic Device RMG 4 - EIB and Additional Device RME 4 EIB
4-/8-/12-Channel Switch Module Switch Actuator Modular with Basic Device RMG 4 - EIB and Additional Device RME 4 EIB page 1 of 45 Table of Content... 1 1 Operational Characteristics... 2 2 Technische Daten...
More information16-Channel Yearly Time Switch TR 648 S DCF
16-Channel Yearly Time Switch TR 648 S DCF Illustration 1 : TR 648 S DCF TR 648 S DCF EIB 648 9 201 DCF 77 Antenna 907 0 271 Obelisk 2.0 Programming set 907 0 305 Obelisk 2.1 Software 931 0 961 Page 1
More information12 Series - Time switches 16 A. Features
12 12 Series - Time switches 16 A Features Mechanical time switches - Daily time setting * - Weekly time setting ** Type 12.01-1 Pole 16 A CO (SPDT) 35.8 mm width Type 12.11-1 Pole 16 A NO (SPST-NO) 17.6
More informationKNX manual High-performance switch actuators RM 4 H FIX1 RM 8 H FIX2
KNX manual High-performance switch actuators RM 4 H FIX1 RM 8 H FIX2 4940212 4940217 2018-10-17 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The FIX2 RM 8 H application programme
More informationOverview per day of the programmed switching times 5 = Friday. Channel statuses / OFF
310 785 01 TR 611 top TERMINA 1-channel 7 day timer According to version Preprogrammed with the current time and summer/ winter norm time Safety Information The connection and installation of electrical
More informationRadio bus system Radio-universal dimming actuator, 1-gang. 1 Safety instructions. 2 Device components. Order-No. : Operating instructions
Order-No. : 1135 00 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure to observe the instructions may cause damage
More informationISOMETER IRDH575. Approvals
Insulation monitoring device for unearthed AC, DC and AC/DC systems (IT systems) with control and display function for EDS insulation fault location systems IRDH575_D00089_02_D_XXEN/09.2018 Insulation
More informationMechanical daily time switch. 35 mm rail (EN 60715) mount
SERES SERES Mechanical time switches - Daily time setting* - Weekly time setting**.01.11.31 Type.01 --Daily --1 CO 16 A --35.8 mm wide --35 mm rail mount Type.11 --Daily --1 O 16 A --17.5 mm wide --35
More informationStyle 5 Style 7. INDEP. QUARTZ MIN.-1/2 MIN. Synchro radio INSTALLATION AND OPERATING INSTRUCTIONS. Réf.: I
Style 5 Style 7 INDEP. QUARTZ MIN.-1/2 MIN. Synchro radio INSTALLATION AND OPERATING INSTRUCTIONS B.P. 1 49340 TRÉMENTINES FRANCE Tél. : 02 41 71 72 00 Fax : 02 41 71 72 01 www.bodet.com Réf.: 605808 I
More informationInstruction manual. art Installation manual
Instruction manual art. 01521 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 4 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL FEATURES AND
More informationModular Devices - Indicators and Push Buttons
Modular Devices - Indicators and Push Buttons The new range of indicator lights and push buttons replaces and expands upon the whole SV range and is composed of the following three families Indicator Lights
More informationKNX manual 1-channel flush-mounted switch actuator SU 1
KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product
More informationisolr275 / AGH-LR Digital Ground Fault Monitor / Ground Detector For Low-Resistance Ungrounded (Floating) AC/DC Systems
T M 1 isolr275 / AGH-LR Digital Ground Fault Monitor / Ground Detector For Low-Resistance Ungrounded (Floating) AC/DC Systems Technical Bulletin NAE1012110 / 12.2011 isolr275 / AGH-LR Ground Fault Monitor
More information2 pole (1 NO + 1 NC) 1 NO + 1 NC 2 NO + 2 NC, 3 NO + 1 NC 4 NO + 2 NC Rated current / Max. peak current Rated load AC1
Features 7S.12...5110 7S.14...0220/0310 7S.16..0420 Relay module with forcibly guided contacts 7S.12 with 2 pole (1NO + 1 NC) 7S.14 with 4 pole (2 NO + 2 NC and 3 NO + 1 NC) 7S.16 with 6 pole (4 NO + 2
More informationModular step relays 16 A
Automation for blinds, grilles and shutters Lighting control in corridors (for hotels, offices and hospitals) Bedroom light control Living room light control SЕRIES FINDER reserves the right to alter characteristics
More information24HR/7 DAY YEARLY 4 CHANNEL INSTALLATION & OPERATING (4 MODULE) 16A. DIGITAL TIMESWITCH Cat. No TR644S INSTRUCTIONS
24HR/7 DAY YEARLY 4 CHANNEL (4 MODULE) 16A DIGITAL TIMESWITCH Cat. No TR644S INSTALLATION & OERATING INSTRUCTIONS 1.0 Description (page 64) 2.0 Features (page 64) 3.0 Application / Installation (page 65)
More informationOperating Manual MU2000K
ZIEHL industrie elektronik GmbH + Co KG Daimlerstr.13, 74523 Schwäbisch Hall, Germany + 49 791 504-0, info@ziehl.de, www.ziehl.de Temperature Relays and MINIKA Mains Monitoring Digital Panelmeters MINIPAN
More informationThis data sheet is only valid in association with the IL SYS INST UM E user manual.
Inline counter terminal, version for extreme conditions, 1 counter input, 1 control input, 1 output, 24 V DC, 500 ma Data sheet 106148_en_03 PHOENIX CONTACT 2015-11-04 1 Description The terminal is designed
More informationPower supply CP-E 48/5.0 Primary switch mode power supply Data sheet
2CDC 271 028 F0008 OUTPUT L+, L+, L-, L-: terminals - output Features Rated output voltage 48 V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output current 5 A Rated
More informationPower supply CP-E 24/0.75
2CDC 271 016 F0t06 a OUTPUT L+, L : terminals output b INPUT L, N, PE: terminals input c LOW: red LED output voltage too low d OK: green LED output voltage OK e OUTPUT Adjust: rotary potentiometer output
More informationPower supply CP-E 24/2.5
2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment
More informationPower supply CP-E 24/2.5
2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment
More informationPower supply CP-E 24/20.0
2CDC 271 027 F0008 a OUTPUT L+, L+, L, L-: terminals output b INPUT L, N, PE: terminals input c 13-14: terminals - signalling contact d OUTPUT OK: green LED output voltage OK e OUTPUT LOW: red LED output
More informationPower supply CP-E 12/10.0 Primary switch mode power supply Data sheet
2CDC 271 024 F0008 OUTPUT L+, L+, L-, L-: terminals - output INPUT L, N, PE: terminals - input OUTPUT OK: green LED - output voltage OK OUTPUT LOW: red LED - output voltage too low OUTPUT Adjust: potentiometer
More informationEIB/KNX Switch Actuators. User manual
EIB/KNX Switch Actuators User manual IT KNT 004 IT KNT 012 Tel.: +34943627988 E-mail: knx@dinuy.com Web: www.dinuy.com Contents 1. Introduction --------------------------------------------------------------------------------------------------------------
More informationRadiocontrol F. Floor Heating Controller Radio control system for floor heating
Radiocontrol F Floor Heating Controller Radio control system for floor heating IMI HEIMEIER / Floor Heating Control / Radiocontrol F Radiocontrol F The Radiocontrol F radio control system for controlling
More informationStep relays 10 A SЕRIES. Lighting control in corridors (for hotels, offices and hospitals) Bedroom light control. Living room light control
Lighting control in corridors (for hotels, offices and hospitals) Bedroom light control Living room light control SЕRIES FINDER reserves the right to alter characteristics at any time without notice. FINDER
More informationTime Switches. Because we have a Responsibility
TIME SWITCHES Time Switches On 8th August 1958, a young entrepreneur manufactured, India's first indigenously developed, sheet steel enclosed rewirable switch at Jalandhar in Punjab, marking the birth
More informationPower supply CP-T 48/20.0 Primary switch mode power supply
Data sheet Power supply CP-T 48/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
More informationLDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications.
LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications. Its compact size, high efficiency, excellent reliability together with easy
More informationDipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str Grünberg Tel.: Fax:
Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str. 65 35305 Grünberg Tel.: 06401 807-0 Fax: 06401 807-259 Insulation fault locator Insulation fault locator for DC IT systems with high system leakage capacitances
More informationPower supply CP-D 24/1.3
2CDC 271 027 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 24 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 1.3 A Rated output power
More informationPower supply CP-T 48/5.0 Primary switch mode power supply
Data sheet Power supply CP-T 48/5.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
More informationPower supply CP-T 24/20.0 Primary switch mode power supply
Data sheet Power supply CP-T 24/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
More informationISOSCAN EDS460-DG. Insulation fault locator for DC IT systems with high system leakage capacitances
ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances _D00108_00_D_XXEN/05.2015 ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances
More informationRadio Touch Order no.: 2880 xx. Operation and installation instructions. 1 Safety instructions. 2 Structure of the device (Figure 1) Radio Touch
Radio Touch Order no.: 2880 xx Operation and installation instructions 1 Safety instructions Electrical equipment must only be installed and assembled by a qualified electrician in accordance with the
More information2 Pole CO, 8 A Plug-in 2 CO (DPDT) 1 CO (SPDT) 8/15 16/25* 250/ /400 2,000 4, /0.5/ /0.5/ (5/5) 300 (10/5)
46 Series - Relays for railway applications 8-16 A 46 SERIES Features Plug-in power relays: 8 A, 2 pole 16 A, 1 pole Complies with EN 45545-2:2013 (protection against fire of materials), EN 61373 (resistance
More information10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units
BETA Switching Transformers, Bells and Socket Outlets /2 Product overview /3 4AC3 0, 4AC3 1 bell transformers /5 4AC3 4... 4AC3 transformers for permanent loads /8 4AC2 4 power supply units / 7LQ2 2 bells
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Order No. : 2126 00 Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationType: EASY719 AC RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC. Description
Type: EASY719 AC RC Article No.: 274115 Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC Description 12 digital inputs 6 relay outputs LCD display Operating buttons Screw terminals
More informationSwitching and control professionals electronic switching relays, control relays and coupling relays
12 Switching and control professionals electronic switching relays, control relays and coupling relays 12 Electronic switching relays, control relays and coupling relays Selection table switching relays,
More informationRadio receiver E17 2-channel, 27 MHz, 40MHz, or 433 MHz, 2 relay outputs. Operating voltage: 230 V/AC or 12 V or 24 V AC/DC available.
Fig.: 230 V version Radio receiver E17 2-channel, 27 MHz, 40MHz, or 433 MHz, 2 relay outputs. Operating voltage: 230 V/AC or 12 V or 24 V AC/DC available. Installation, connection and programming instructions
More informationQUINT-PS-24DC/24DC/10
QUINT-PS-24/24/10 QUINT - converter, primary switched mode, input: 24 V, output: 24 V /10 A INTERFACE Data Sheet PHOENIX CONTACT - 02/2006 Description The QUINT - converter 24 V/10 A converts the voltage
More informationElectronic timer CT-AWS Impulse-OFF with 1 c/o contact Data sheet
2CDC 251 121 F0004 1 5 2 4 3 6 Characteristics Single-function impulse-off timer One device includes 10 time ranges, from 0.05 s to 300 h, for the adjustment of the pulse time Remote potentiometer connection
More informationPower supply CP-D 12/2.1
2CDC 271 025 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 12 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 2.1 A Rated output power
More informationK-BUS Switch Actuator
K-BUS Switch Actuator User manual-ver. 2 KA/R0416.1 KA/R0816.1 KA/R1216.1 Contents Contents... 2 1. Introduction... 3 1.1 Product and function overview... 3 2. Technical Properties... 3 3. Commissioning...
More information"Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting
Smart "Compact" range with display CD12 Smart Part number 88974043 "Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting Type Input
More informationPower supply CP-T 24/10.0 Primary switch mode power supply
Data sheet Power supply CP-T 24/10.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
More informationPower supply CP-T 24/40.0 Primary switch mode power supply
Data sheet Power supply CP-T 24/40.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
More informationOperating Instructions PROFITEST H+E TECH. Diagnostics Unit for Electric Charging Stations (Type 2 Connector Socket and Plug) /3.
Diagnostics Unit for Electric Charging Stations (Type 2 Connector Socket and Plug) 3-349-878-03 1/3.16 Opening the Instrument / Repairs The instrument may only be opened by authorized, trained personnel
More informationLOW VOLTAGE CONVERTER WITH THREE POINT GALVANIC INSULATION
EN K09LV LOW VOLTAGE CONVERTER WITH THREE POINT GALVANIC INSULATION General Description The K09LV instrument is a three points galvanic insulator, with input on high sensitivity voltage, and active output.
More informationElectronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact The CT-TGD.12 is an electronic time relay with the function pulse generator. It is from the CT-D range. With their MDRC profile
More informationElectronic impulse switches the silent revolution
12 Electronic impulse switches the silent revolution 12 Electronic impulse switches Selection table electronic impulse switches 12-2 Impulse switch ES12DX 12-3 Impulse switch ES12-200 12-4 Impulse switch
More informationMicro Contactors. Micro Contactor Relays 10. Micro Contactors 11. Micro Contactors With Solder Pins 12. Coil voltages 12. Micro Reversing Contactor 13
Micro Contactor Relays 10 Micro Contactors 11 Micro Contactors With Solder Pins 12 Coil voltages 12 Micro Reversing Contactor 13 Technical Data 14 Dimensions 18 D946E 9 Micro Contactor Relays 4-pole AC
More informationPIR6WT-1Z interface - time relays
1 9-functions electronic time relays compliance with standard PN-EN 612-1 Time relay PIR6WT-1Z consists of: - universal socket with electronic PI6WT-1Z with screw terminals, - changeover relay RM699V,
More informationMoeller Electric Corporation
EMR4-I Current Monitoring Relays 02/0053 EMR4-I1-2-A EMR4-I15-2-A EMR4-I15-2-B Mechanical lifespan operations x10 6 30 30 30 24-h cycle, 55 C, 93 % relative humidty, 96 h Ambient temperature min./max.
More informationOperating instructions Electronic level sensor LK / / 2008
Operating instructions Electronic level sensor LK31 UK 704046 / 00 01 / 2008 Contents Safety instructions...2 Menu structure...3 Controls and indicating elements...4 Function and features...5 Functional
More informationDeltaSol AX HE * * Differential temperature controller Manual for the specialised craftsman
DeltaSol X HE Differtial temperature controller Manual for the specialised craftsman Installation Operation Functions and options Troubleshooting *110633* 110633 Thank you for buying this RESOL product.
More informationPower supply CP-D 24/4.2 Primary switch mode power supply
Data sheet Power supply CP-D 24/4.2 Primary switch mode power supply The CP-D range of modular power supply units in MDRC design (modular DIN rail components) is ideally suited for installation in distribution
More informationEY-EM 527: Remote I/O module, ecolink527
Product data sheet 94.078 EY-EM 527: Remote I/O module, ecolink527 How energy efficiency is improved Regulation, control, monitoring and optimisation of operational systems, e.g. room automation or HVAC
More informationSINEAX B 811 Power Pack with additional Functions
SINEA B 8 for intelligent and conventional s, in housing S7 for rail and wall mounting 002 II () G Application The power supply unit SINEA B 8 (Figure ) provides the DC power supply for s and transfers
More information62 Series - Power relays 16 A. Features / /
6 Series - Power relays 6 A Features 6. / 6.3 6.-0300 / 6.3-0300 Printed circuit mount 6 A Power relay & 3 Pole changeover contacts or NO ( 3 mm contact gap) AC coils & DC coils Reinforced insulation between
More informationJUMO Wtrans Receiver with Wireless Data Transmission
Data Sheet 902931 Page 1/10 JUMO Wtrans Receiver with Wireless Data Transmission k For measuring temperature, pressure, potentiometer, and voltage. k Interface RS485 with Modbus protocol k Wireless measured
More informationAHC-XP. Dewpoint-guided Power Controller for Glass and Handrail Heaters. Front view. Characteristics
Dewpoint-guided Power Controller for Glass and Handrail Heaters Front view Characteristics Dew point-guided power controller for cost-optimized operation of glass and handrail heaters Digital display of
More informationPortable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an
EDS309 Portable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an equipment for insulation fault location EDS309x_D00012_00_D_XXEN/05.2015
More informationType: EASY719 DA RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC. Description
Type: EASY719 DA RC Article.: 274117 Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
More informationC4000. inline control. Photometric Converter. Real-time photometric converter. Factory zero for scattered light sensors
C4000 Photometric Converter inline control Real-time photometric converter Factory zero for scattered light sensors Simultaneous operation of up to four inline sensors Process control functions via Remote
More informationENCORE 300 SERIES INSTALLATION AND OPERATING INSTRUCTIONS
ENCORE 300 SERIES INSTALLATION AND OPERATING INSTRUCTIONS Copyright 2002-2006 PRI Ltd. 9600-3004-2 Issue C Information contained within this document is subject to change without notice and does not represent
More information3.5 mm contact pin pitch 1 Pole 12 A PCB direct or via socket
41 Series - Low profile PCB relays 8-12 - 16 A Features 41.31 41.52 41.61 1 & 2 Pole - Low profile (15.7 mm height) 41.31-1 Pole 12 A (3.5 mm pin pitch) 41.52-2 Pole 8 A (5 mm pin pitch) 41.61-1 Pole 16
More informationEMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description.
Electronic monitoring relay for voltage monitoring in three-phase networks INTERFACE Data sheet 102110_en_03 1 Description PHOENIX CONTACT - 09/2009 Features Increasingly higher demands are being placed
More informationEY-EM 522, 523: Remote I/O module, ecolink522, 523
Product data sheet 94.077 EY-EM 522, 523: Remote I/O module, ecolink522, 523 How energy efficiency is improved Regulation, control, monitoring and optimisation of operational systems, e.g. room automation
More informationLevel Switch NRS 2-50 NRS Original Installation Instructions English
Level Switch NRS 2-50 NRS 2-51 EN English Original Installation Instructions 819179-03 1 Contents Important Notes Page Usage for the intended purpose...4 Function...4 Safety note...4 Directives and Standards
More informationIMPULSE SWITCH, REMOTE SWITCH
W REMOTE SWITCH STELLA W SCHRACK INFO Low switching noise Energy saving function 0.5 30 minutes High switching capacity, 80 A start-up peak LED display LQ540000 W APPLICATIONS 220 The ideal solution for
More informationWLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING
WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (a water meter with pulse output proportional
More informationElectronic timer CT-EBE Flasher starting with OFF, 1 c/o (SPDT) contact
Data sheet Electronic timer CT-EBE Flasher starting with OFF, 1 c/o (SPDT) contact The CT-EBE is an electronic time relay with the function flasher starting with OFF. It is from the CT-E range. The CT-E
More information27/04/2015
Modular Carril DIN 35 mm HIL Part number 84871120 Control of AC and DC currents Automatic recognition of AC/DC Measurement ranges from 2 ma to 10 A Choice between over and undercurrent True RMS measurement
More informationSEN TRONIC AG. Millenium 3 Essential. Essential range: powerful but cost effective. Part numbers. Accessories
Millenium Essential Essential range: powerful but cost effective Industrial temperature range (0 C +55 C) Analog inputs 00 DC, Potentiometer (00 ma/pt00 with converters) Display versions: Green LCD with
More informationMeasuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC
2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from
More informationCAMTO. Arc detecting relay. system. January Revised August D D1200
NEW ARC DETECTING SYSTEM FROM Based on our experience with arc protection since 1962, has developed a new. The units are built into boxes that all fit on a 35 mm DIN-rail. All front plates are dimensioned
More informationLow profile safety relay with forcibly guided double contacts FEATURES. Relay height, 14.5mm. 4a2b
Low profile safety relay with forcibly guided double contacts SFN4D RELAY 3.3 33.0 FEATURES Relay complies with EN 020, Type B. Polarized magnet system with snap action function Tolerance ±0.3 mm Weight
More informationInstallation / Monitoring Technique
Installation / Monitoring Technique VARIMETER RCM Residual Current Monitor, Type B for AC and DC Systems IP 5883 0249633 IP 5883 ND 5018/035 ND 5018/030 According to IEC/EN 62 020, VDE 0663 For AC and
More information02/11/2015
Smart "Compact" range with display CD20 Smart Part number 88974053 Highly visible blue LCD with 4 lines of 18 characters and configurable backlighting Allow the use of the entire library of specific functions
More informationEMD-FL-C-10. Current Monitoring Relay. Data Sheet. Functions. Structure 08/2004
Current Monitoring Relay Data Sheet 08/2004 Functions Structure Current monitoring of direct and alternating current in 1-phase networks with settable threshold values, starting override and response delay
More informationKeysight U1461A Insulation Multimeter/ U1453A Insulation Tester
Keysight U46A Insulation Multimeter/ U453A Insulation Tester Quick Start Guide Standard Accessories Included In Your Purchase Standard Accessories Included In Your Purchase The following accessories are
More informationTransformers, Power Supply Units and Socket Outlets
Transformers, Power Supply Units and Socket Outlets /2 Introduction /3 4AC3 bell transformers /4 4AC3 safety transformers /5 4AC2 power supply units /6 5TE6 REG socket outlets For further technical product
More informationCustom "Compact" range with display CD20 Custom Part number
Custom "Compact" range with display CD20 Custom Part number 88974051 "Modular" versions designed for Custom application-specific functions (Custom functions) LCD with 4 lines of 18 characters and configurable
More information13 SERIES. Electronic step relays A
13 Electronic step relays 10-16 A 13 13.81 - Electronic step relay - Rail mount - 1 Pole 13.91 - Electronic step relay and timing step relay Switch box mount - 1 Pole Fixed time (10 minutes) timing function
More informationThe power in relays and timers since Catalogue
The power in relays and timers since 1954 2012 Catalogue PCB relays Industrial relays Relay interface modules Sockets and accessories Timers Monitoring relays Energy meters Surge protection devices Industrial
More informationseries dimmer actuators, DMG 2 S, Upgrade Module DME 2 S and Booster DMB 2
series dimmer actuators, DMG 2 S, Upgrade Module DME 2 S and Booster DMB 2 DMG 2 S 4910270 DME 2 S 4910271 DMB 2 4910272 Version: Jan-11 (Subject to change) Page 1 of 59 Contents 1 FUNCTIONAL CHARACTERISTICS...
More information