SIMPLY CLEVER. ŠkodaAuto RADIO NAVIGATION SYSTEM SatCompass

Transcription

1 SIMPLY CLEVER ŠkodaAuto RADIO NAVIGATION SYSTEM SatCompass

2 Introduction You have opted for a Škoda vehicle, which is fitted with a radio navigation system SatCompass, (designated in the following as navigation system ) - we thank you for your confidence in us. We recommend that you read this Owner's Manual attentively to enable you to become familiar with your navigation system and all that it offers as quickly as possible. Please do not hesitate to contact your Škoda Service Partner or importer should you have any further questions regarding any problems with your navigation system which may arise. Any national legal provisions which vary from the information contained in this Owner's Manual take precedence over the information contained herein. We wish you much pleasure with your navigation system and pleasant motoring at all times. Your Škoda Auto

3 2 Contents Contents Layout of this Owner's Manual (explanations) Navigation Overview of navigation basic menu Enter Enter destination - Town Enter destination - Street - Intersection Enter destination - Town centre Destination entry - Special destination Enter destination - From destination memory Enter destination - Flagged destination Route options Route guidance Destination memory Bypass a jam TOURLIST Travel guide General comments General view Radio navigation system SatCompass Important information Changing the navigation CD Functional description of the buttons Display Basic settings of the navigation system Anti-theft protection Audio Radio mode Radio mode with RDS Switch on radio mode Set and store station Retrieving the stored stations Replay recorded traffic information CD mode Glossary Description Index

4 Layout of this Owner's Manual (explanations) The Owner's Manual has been systematically designed, in order to make it easy for you to find and absorb the information you require. Chapters, table of contents and subject index The text of the booklet are divided into short sections which are combined into easy-to-read chapters. The Table of contents is arranged according to the chapters and the detailed Subject index at the end of this booklet helps you to rapidly find the information you are looking for. Brief information and instructions Each section has a Heading. This is followed by Brief information (in large italic lettering), which tells you the subject which is dealt with in this section. Most of the illustrations are accompanied by an Instruction (in large letters) which explains to you in a straightforward way the action you have to take. Work steps which have to be carried out begin with a hyphen. Special equipment Equipment which is marked * is only standard on certain vehicle model versions or only suppliable as special equipment for certain models. s All three kinds of notes (WARNING! Caution! and ), which are contained in the text, are stated at the end of the respective section. Layout of this Owner's Manual (explanations) 3 Caution A Caution! note draws your attention to the possibility of damage to your vehicle or points out general risks of an accident. A normal draws your attention in a general way to important information for the operation of your unit. WARNING The most important notes are marked with the heading WARNING!. These Warning notes draw your attention to a serious risk of accident or injury.

5 4 General comments General comments General view Fig. 1 General view A1 A2 A3 A4 Button for manual station tuning FM, AM, TIM and TMC and to select the track in the CD mode Button FM to activate the FM radio mode Button TIM (Traffic Information Memo) to quickly retrieve the stored traffic announcements CD - eject button A5 A6 A7 A8 A9 Button TMC (Traffic Message Channel) to activate the TMC radio mode Button AM to activate the AM radio mode CD-case Display - screen Button DSP for setting the display contrast

6 General comments 5 A10 Button CD to activate the CD and CD changer mode* A11 Button for manual switch over between day and night display A12 Button NAVI calls up the navigation basic menu A13 Button TELE displays the traffic reports received via TMC A14 Radio mode retrieving the stored station automatic station finding in AM waveband fast station finding (audible) TIM fast station finding in CD mode A15 Button MUTE for switching on/off the mute function of the audio sources radio, CD und CD changer* A16 Button SCAN for a brief playing (ten seconds) of all stored stations (TP,FM and AM) - in radio mode Playing all tracks on a CD one after the other A17 Button INFO displays continuous information A18 Button MIX plays the tracks on a CD in random order A19 Rotary/push knob for switching on and off (press) the navigation system, volume control (turn) A20 Button AS automatically stores the station A21 Button for storing the current vehicle position as flagged destination A22 Station selection buttons in radio mode and CD direct selection buttons in CD changer mode* A23 Delete button for deleting entries in the editing field A24 Button sound for adjusting the sound and volume distribution A25 Menu knob for selecting and confirming the menu points A26 Button for calculating an alternative route in case of traffic congestion A27 Button to exit a menu. A28 Button SET calls up the SETUP menu A29 Macro button, programmable function key Radio navigation system SatCompass Special equipment The navigation system SatCompass offers you an easy handling of the convenience equipment radio, CD player and navigation system in the vehicle. The system can be equipped with an original 6-compartment CD changer*. Navigation The navigation system is your intelligent front passenger. You can reach the desired destination quickly, easily and reliably without time-consuming map searching from the starting point of your trip. In unknown locations it saves you time by guiding you to the next filling station. You can make an intermittent stop on the road, in order e.g. to go and eat in a restaurant or to visit a sight. The system uses the data stored on the navigation CD for the calculation of the trip destination. During the guidance you will receive via different screen displays information about vehicle position; notes regarding turns (direction and distance until the turn) and the arrival time at the trip destination. Announcement of the ŠkodaAuto navigation system Under certain requirements the system must be announced, as it is equipped with a radio unit. How does the navigation system function? The current vehicle position is determined using satellites. The distance travelled is measured by the ABS. The direction of travel is determined using a gyroscope. The navigation system is provided with this information and compared with the stored data. Outside the densely populated areas it is possible that this type of locating does not permit exact position definition. In this case the locating is performed via satellites. This type of locating is referred to as Global Positioning System (GPS) - global satellite locating system.

7 6 General comments Important information Warranty The same warranty terms apply for the equipment as for new vehicles. A damage in the sense of the warranty must not be the result from improper handling of the system or from unprofessional repair attempts. In addition, no external damage must be present. Replacement possibility After the expiration of the warranty, a unit in need of repair will be replaced inexpensively with a reconditioned, original unit with spare part warranty. However it is required that there is no housing damage and no unauthorised repair attempts have been made. In the case of a warranty or a replacement service, the Škoda Service Partner must be presented with the unit card with code number and serial number! The unit card can be found at the back of the operating instructions. Information on how to operate the navigation system The requirements of today's street traffic demand from the driver that he always concentrates fully when driving. The extensive and fastidious equipment details of this system offer - besides the possibilites of entertainment - also a wide range of information which will help you reach the trip destination quickly and reliably. Only if the traffic situation allows it, should you operate the navigation system with its wide range of possibilites. The volume settings must be selected in such a way that acoustic signals from the outside, such as e.g. a Martins horn from utility vehicles (police cars, ambulances and fire brigade), can be heard at any time. WARNING Please always pay full attention to the traffic situation around you! As the driver you are fully responsible for the traffic safety. Only use the functions in such a way that you always maintain the control over your vehicle in all traffic situations! Anti-theft coding After removing the unit, the anti-theft coding prevents electronically the use of the unit by an unauthorised person. If the information SAFE appears in the display after switching on the unit, it can only be operated again by entering the correct code page 15. Before using the navigation system Please observe the respective traffic regulations when driving. Street and location names can be changed. There are exceptional cases in which the names stored on the CD might not correspond to the changed names. The route calculated by the navigation system is a recommendation for reaching the trip destination. While driving please pay attention to stopping restrictions, traffic lights, one-way streets, toe change restrictions, channels and ferries. WARNING The road traffic legislation (StVO) is always applicable, also if a driving recommendation does not comply with the StVO.

8 General comments 7 Calibration after tyre change After a tyre change it may be necessary to calibrate the navigation system again. Mark and confirm the menu point TYRE CHANGE in the menu SETUP-NAVIGATION with the menu knob A25. After confirming the safety question the calibration is automatically started. An information for the calibration procedure is shown in the display. During the calibration other functions of the navigation are not possible. Care of the display Carefully handle the display because dents and scratches can occur through pressure of the finger or contact with sharp objects. The display can be cleaned with a soft cloth and finger marks can be wiped away with pure alcohol. Do not use solvent such as turpentine or petrol as they will corrode the display surface. Changing the navigation CD Description Press the CD eject button A4 to change the CD. The navigation CD is ejected. Carefully insert the new navigation CD with the inscription upwards as far as possible into the CD case until it can be drawn in automatically by the unit. Caution Only clean CDs without scratches and damages should be used, in order to guarantee a proper functioning of the navigation system. Store the non-used navigation CD in the bag provided for this. Never expose CDs to direct sun rays! Please never write or affix the CDs! Functional description of the buttons Switching the system on and off The system is switched on or off by pressing the rotary/push knob A19. The audio source or the navigation status (if the last route guidance dates back more than 30 minutes) which was active before switching the system off is activated. If the key is pulled out of the ignition lock when the system is switched on, the system switches off autmatically. You can switch on the system again by pressing the rotary/push knob A19. If the engine is switched off, the system (protection of the vehicle battery before discharging) switches off automatically after approx. one hour. This process can be repeated as often as desired. If the system is switched off and the ignition key is withdrawn, a flashing LED indicates that this is a system with an active anti-theft coding. Change the volume to the right or to the left by turning the rotary/push knob A19.

9 8 General comments If the information SAFE appears in the display after switching on the unit, it can only be operated again by entering the correct code page 15. Button TIM With the navigation system there is the possibility to record traffic information over a period of 2 and/or 24 hours. Up to nine traffic reports with a total duration of maximum 4 minutes can be automatically recorded. The TP stations always record traffic reports during operation, also if the play function is aborted by pressing the button FM A2. In the case of EON stations, also the recording is aborted. If the system is switched off, the reports are only recorded if the function TIM is activated. Activate 24 hour TIM readiness If the system is switched off and the ignition key is withdrawn, hold the button TIM A3 pressed for a few seconds. Activate 2 hour TIM readiness Withdraw the ignition key when the system is switched on and the vehicle is stationary. The recording readiness is deactivated by switching the system on. The 24 hour TIM readiness leads to an increased power consumption over 24 hours. This can lead to problems with the voltage of the vehicle battery, if the vehicle is only driven on short distances. In this case the 24 hour TIM readiness should not be activated. The oldest traffic information will be overwritten if the traffic information memory is full. If a report lasts more than four minutes, the beginning of this report is overwritten. Button DSP Press the button DSP. The contrast can be set by pressing the menu knob A25. Confirm the set value by pressing the menu knob A25. Button TELE With the button TELE A13 incoming traffic reports can be displayed in the display via the TMC (Traffic Message Channel - traffic message channel). These reports are used by the navigation system for the dynamic route guidance, if this option is active page 29. The number of received traffic reports is shown below the display TMC through corresponding points. If the button TELE A13 is pressed, a text appears in the display. In the standard field - background - of the display page 9, fig. 2 the number of the indicated report and the number of stored reports is shown behind TRAFFIC INFO. To change in-between individual reports, turn the menu knob A25. The TMC function is only available if a navigation CD has been inserted. Reports are deleted after 15 minutes, if they are not received again. If there is no report, a corresponding note is displayed in the display. Button MUTE Mute the audio sources by pressing the button MUTE A15. AUDIO OFF is shown on the display. Press the button MUTE A15 again or turn the rotary/push knob A19 to switch the mute function on/off. The display contrast can be set with the button DSP A9.

10 General comments 9 Button SCAN Display All receivable stations in each band can be played for 5 seconds with the function radio scan. Select with the buttons FM A2, TMC A5 or AM A6 the band in which you wish to carry out the scan finding. Press the button SCAN A16 briefly. If you wish to select the scanned station, press again the button SCAN A16. Display If you have selected no station, the function radio scan is repeated after a frequency process. Fig. 2 Layout of the display Button INFO Press the button INFO A17 to receive more information about the current destination or the list entries, which are marked with continuation points. After pressing the button INFO A17 the current destination is shown in the standard field - foreground - of the display fig. 2 and a repetition of the last voice response of the navigation is performed if the route guidance function is active. A detailed display of the list entries shown with continuation points is given in list menus. Other list entries can be retrieved by pressing the menu knob A25. If further information is available on your navigation CD, it can be called up in the menu TRAVEL GUIDE. The functions and menus displayed on the display result from the following standard fields fig. 2: Background If the navigation is active the status of the functions radio, CD or CD changer* is displayed at the top of the display. In radio or CD mode the function of the navigation active at this moment in time is displayed. Foreground In case of active navigation, the optical driving recommendations are shown in the foreground. In radio mode the station or the frequency is shown in this standard field, in CD mode TRACK and the current track number. Status range The display appears only in audio mode. The status range serves as display of the current audio source and the traffic radio readiness.

11 10 General comments Display contents The display shows the following content: Fig. 3 Display overview A selected audio source, AB selected memory space, AC name of the selected station, AD display that the set station is a TMC station as well as the number of received traffic reports, AE arrival time, AF selected route option (here dynamic), AG distance to destination, AH direction arrow, AI distance to the next decision point, AJ name of the currently driven road. Alarm If your navigation system receives a disaster announcement, ALARM is displayed in the standard field - foreground - of the display. The display appears in the standard field - background during active route guidance. The play function of the active audio source is interrupted and the navigation system switches over to the corresponding radio station that is receiving the disaster announcement. The play function of the announcement is perfomed with the volume page 13 set for traffic information. At the end of the announcement it switches back automatically to the last active audio source. You can end the traffic information at any time by switching over to another audio source or setting another station. Telephone If your vehicle is equipped with a hands-free system*, the voice play function of the telephone is performed via the navigation system. If the telephone is activated, the audio sources are switched to mute. PHONE is displayed on the display. After the end of the conversation, the audio play function is continued. If the navigation system is switched off, it switches on automatically when activating the telephone. The display is not switched on. You can phone as before. After the end of the conversation, the navigation system automatically switches off again.

12 General comments 11 Basic settings of the navigation system SETUP MENU If the selection has been confirmed, the next sub-menu will be displayed. The selection marking remains on the first menu point. The menu title is shown in the standard field - background - of the display. Mark and confirm the menu point to be changed by using the menu knob A25. The setting can be carried out. Change the settings The menu point you wish to change is circled. The setting is changed by turning the menu knob A25. Confirm the changed setting by pressing the menu knob A25. Exit the menu Fig. 4 Layout of the menu Call up the SETUP MENU by pressing the button SET A28. All basic functions of your navigation system are set in the SETUP MENU fig. 4. The display contents of the menu are divided into menu title and menu points. If one menu contains more than five menu points, thus the other menu points are not within the illustrated range. Such menus are marked by arrows on the right. Other menu points are shown if the selection marking is moved before the last or second menu point of the list. After a further actuation of the menu knob A25 the selection marking remains at the point and the other menu points are displayed. If you do not wish to take over the changed setting, press the button A27. If you wish to change to the previous menu, press once again the button A27. To exit a basic menu, select another function, e.g. FM or CD. Navigation settings Selecting and confirming menu points Select and operate the menu points by using the menu knob A25. To move the selection marking upwards or downwards, turn the menu knob A25 to the right or left. The selected menu is displayed inversely. Confirm the selection by pressing the menu knob A25. Fig. 5 Navigation settings Call up the menu SETUP-NAVIGATION by selecting the menu point NAVIGATION in the SETUP MENU.

13 12 General comments SETTINGS Here you will reach a sub-menu for determining the system settings: TIME INFO - here you can select if the ARRIVAL TIME at destination or the REMAINING TRAVEL TIME to the destination should be displayed. LANGUAGE - if the route guidance should be performed without voice response, then select the option OFF. In case of deactivated voice response, the route guidance can only be performed with optical driving recommendations on the display or the instrument cluster. REMEMB. DEST. - automatically stores the last 10 destinations in the memory LAST DESTINATIONS switch on or off. DRIVING SYMBOLS - if you wish the display of optical driving recommendations only in the instrument cluster, then select the option OFF. LOCATION If no GPS reception page 5 is possible, the location can be entered here manually. TYRE CHANGE If new tyres were mounted page 7, select this menu point. Audio settings Fig. 6 Audio settings The settings for the audio mode can be carried out in the menu SETUP AUDIO fig. 6. RDS NAME Certain stations use RDS not only to transmit their name but also for advertisement. Here you can set if the name of a station called up out of the memory should be set fixed in the display FIX or if alternative news, e.g. advertisement, should be displayed VAR. RDS-REG Here you can select if the navigation system should also set RDS stations, which transmit another regional program than the currently heard one. This setting may be necessary, if the reception is so weak, that there is a risk of a program loss page 16. AUTO - when selecting this setting the change to regional related station frequencies is only performed if there is a risk of a program loss. OFF - a regional related station frequency can be set manually. No automatic change is carried out. CD-MIX This menu point can only be activated in combination with CD changer *. Set the DISC, if first all tracks of the active CD and then all tracks of another CD should be played in random order. Set the MAG (Magazine), in order to hear all tracks of the entire magazine in random order. MUSIC/SP. RDS stations have the possibility to transmit a signal which in case of text messages switches over the frequency input of your navigation system to the voice play function, to do so e.g. treble is decreased. The voice play function is clearer and can be heard better. AUTO - the frequency response of the voice play function is automatically changed when the corresponding signal is received. OFF - select, if you do not wish an automatic adaptation of the frequency response.

14 General comments 13 TA Here you can set if your navigation system should replay incoming traffic information. ON - all incoming traffic information is replayed. If TA is switched on, only TP stations can be set. OFF - Traffic information is not replayed. Volume settings If at a particular time of a traffic information or voice response the system volume is higher than TA MIN or NAV-MIN, this is also performed in the system volume. Macro button settings Fig. 8 Macro button settings Fig. 7 Volume settings VOL-ON - Setting the switch on volume of the system. TA MIN - setting the minimum volume for traffic information. NAV-MIN - setting the minimum volume for the voice response of the navigation. TELEPHONE - if your vehicle is equipped with a hands-free system*, a call is replayed via the navigation system. Here you can set the volume, with which you can hear your conversation partner. GALA - the volume of your navigation system is increased automatically with increasing speed and thus high exterior noises. Here you can set the degree of accentuation. The macro button A29 can be assigned to one of the following functions: ROUTE GUIDANCE - activates the route guidance, if a destination has already been defined. ROUTE OPTIONS - calls up the menu for selecting the route calculation. ROUTE LIST - calls up the route list during an active route guidance. LAST DESTINATIONS - shows the content of the memory - LAST DESTINATIONS - of the navigation. ALPH.DEST.MEMORY - calls up the alphabetically classified destination memory. GPS STATUS - shows the number of current GPS satellite receptions and the geographic position. TOGGLE TIME INFO - allows the switch-over between arrival time and remaining travel time.

15 14 General comments SHOW LOCATION - the route guidance is performed under the information of all directions, where the destination is located and if necessary the name of the driven road. The system time can only be changed, if no GPS Time can be received. When calling up the menu the selection marking is on the menu point ROUTE GUIDANCE. The current assignment of the macro button is marked with an arrow. Time settings Language The displays and the announcements of the navigation can be selected in the following languages: Czech German English (Imperial) - Measurements given in yards English (Metric) - Measurements given in metres Spanish French Italian Dutch Factory settings Fig. 9 Time settings The menu point GPS TIME cannot be set. It serves for the calculation of the system time for GPS reception. If the GPS TIME is available, the SYSTEM TIME cannot be set manually. TIME ZONE - here you can enter the difference of the time zone in which you are at the moment to the world standard time - UTC. DAYL. SAV. - select ON, if you are in a country, in which daylight saving applies at the time of the setting. SYSTEM TIME -select and confirm the menu point SYSTEM TIME with the menu knob A25. Now the time can be set by pressing the menu knob A25. In order to change to minutes, press once again the menu knob A25. End the setting by pressing once again the menu knob A25. Here you can reset all settings of the SETUP menus and the sound settings to the factory setting. Language setting and calibration are exempt. If you select and confirm the menu point FACTORY SETTINGS after pressing the button SET A28 you will be requested once again to confirm your selection. If you have selected and confirmed the menu point YES, the factory settings are reset (language setting and calibration are exempt). The navigation system switches off briefly and then on again. If you do not wish to reset the navigation system, select the menu point NO.

16 General comments 15 If the navigation CD is inserted there is the possibility beforehand to delete the stored destinations. If you wish to delete the stored destinations, select the menu point YES, if not, select NO. Anti-theft protection Anti-theft coding The anti-theft coding of your navigation system prevents an operation of the system after a voltage interruption, e.g. during a vehicle repair or after theft. After disconnecting the battery, after separating the navigation system from the onboard voltage of the vehicle and after a defective protection, the entry of the code is required when operating. In such cases SAFE is shown in the display after switching on. Caution This code number is affixed together with the unit number on the Unit card, which is located behind the instructions. The unit card must be disconnected and stored outside the vehicle. The code is normally stored in the instrument cluster. Through this the navigation system is automatically decoded (convenience coding). A manual entry of the code is normally not necessary. Code entry Switch on the navigation system - after the start screen with the display SAFE the request for entry of the code number is displayed after 2 seconds 1000 is shown on the display. Continue pressing the station selection button 1 A22 until the first digit of the code number is shown in the display. Insert the other digits of the code number by repetitively pressing the station selection button 2, and/or 3 or 4 A22. If the entire code number was entered, press the menu knob A25 or the button A1 or the button A14 for at least 2 seconds. Entry of an incorrect code number If inadvertently an incorrect code number was confirmed when entering, SAFE is shown again in the display. First of all flashing and then permanent. WRONG TRIES: 1 is shown on the display. Now the entire process can be repeated once again. If the code number is entered incorrectly for the second time, the navigation system will be blocked for approx. one hour. It is only possible to repeat the entry of the code number after an hour has expired and while the navigation system is switched on and the ignition key remains in the ignition lock. If once again two non-valid attempts are undertaken, the navigation system will be blocked again for an hour. The cycle - two attempts, blocked for an hour - furthermore applies. Please do not hesitate to contact your Škoda Service Partner should you have lost the unit card. The electronical lock is cancelled by entering the correct code. The order of the following operating steps must be maintained:

17 16 Audio Audio Radio mode Radio mode with RDS The function RDS is always active for the navigation system. More and more USW broadcasting companies transmit RDS information in addition to the program. E.g the station name and the traffic status of the set station belong to this information. Alternative frequency AF The function alternative frequency ensures that the best receivable frequency of the selected station is automatically and precisely set. The replay of the broadcast can be muted briefly during the search process according to the best receivable frequency. If no alternative frequency of the set station can be found and the station no longer offers a satisfactory quality, then please select another station. TMC (Traffic Message Channel) Certain radio stations transmit digital traffic announcements in addition to their programme. The announcements are received by your navigation system and used for a dynamic route guidance page 29. If a station has TMC at its disposal, TMC is shown in the standard field - status range - of the display. These stations can be stored on two memory levels TC1 and TC2. RDS regional Certain programs of the broadcasting companies are divided into regional programs at specific times. First of all the unit attempts to set only alternative frequencies of the selected station. If the quality is however so low, that there is a risk of a program loss, the navigation system accepts also frequencies, which are related to the station. As this station emits temporarily different programs and due to such a change in frequency also the programme from one of the related stations can be heard page 12. Switch on radio mode Press the button FM A2, TMC A5 or AM A6 in order to switch on the radio mode. After pressing the button the last set station, if receiveable, is selected. If FM is changed to TMC or vice versa, the set station is taken over in the selected level. Set and store station Manual station tuning Press one of the buttons A1 in order to manually tune a station. At every press the frequency changes to fixed, defined steps upwards or downward. Automatic station tuning Press one of the buttons A14 for a station finding, in a frequency range, upwards or downwards. The next or the previous station is automatically set and selected. If you hold the button A14 pressed, the station continues quickly to the next station.

18 Audio 17 Store station Select the desired range and the level using the button FM A2, TMC A5 or AM A6 Set a station. Hold the station selection button A22 pressed on the station which should be stored, until the station is switched to mute. Automatically store station Select the memory level (FM, TMC or AM), in which the stations should automatically be stored. Hold the button AS A20 pressed until the automatic storing begins and A-STORE is shown in the standard field - status range - of the display. Additionally a progress display in percentage is shown in the standard field - foreground - of the display. The stations with the strongest reception are stored automatically on level 2 (FM2, TC2 or. AM2) of the set range. The order of the stored stations depends on their station code. In the current range you can select up to six stations with the strongest reception using the button AS A20. An Autostore for TMC stations can take 10 minutes, as all receiveable stations are checked for their TMC compatibility. At this time no radio mode is possible. Retrieving the stored stations Select the desired range and the level using the button FM A2, TMC A5 or AM A6 Briefly press the station selection button A22 under which you have stored the station. You can also call up the stored stations by pressing the button A14. If a stored FM station is no longer receivable and the TA function is activated in the SETUP AUDIO, TP-SEEK is shown in the display after pressing the station selection button A22, a finding is started and the radio play function is switched to mute. If no TP station is receivable, a signal tone sounds and NO TP is shown in the display In such a case the function TA switches off page 13. If a stored TMC station is no longer receivable, TMC-SEEK is shown in the display. If no TMC stations are receivable, NO TMC is shown in the display. In such a case select an FM station. If no TMC stations are received, a dynamic route guidance is not possible. Replay recorded traffic information After pressing the button TIM A3, TRACK and the number of the last recorded information is shown in the standard field - foreground - of the display. In the standard field - status range - of the display the time of the recording is shown next to the source display. If no information was recorded, NO MESSAGE is shown in the standard field - foreground - of the display. Select recorded traffic information Press one of the buttons A1 while replaying a recorded traffic information, in order to listen to the previous or the next one. Fast station finding (audible) In order to play the information faster, press one of the buttons while replaying. A14

19 18 Audio Deleting traffic information Trafffic information is automatically deleted six seconds after end of readiness. Ending TIM function Press again the button TIM A3 to end the TIM function. The TIM function is automatically ended after replaying all information. If the TIM function was called up from the menu ROUTE GUIDANCE, it can be shown again by pressing the button TIM A3. CD mode Internal CD drive Your navigation system gives you the possibility to play audio CDs in the internal drive. In addition a CD changer * can be connected. Inserting the CD Slide the CD with the written side facing up into the CD case. Insert the CD as far as possible until it can be drawn in automatically by the navigation system. After the CD was drawn in, the navigation system automatically switches over to CD play function. The play function begins, system oriented after a few seconds with the first track of the CD. TRACK and the current track number are shown in the standard field - foreground - of the display. Starting CD mode If a CD has already been inserted, press the button CD A10. The play function begins at the point where it was last interrupted. If the CD is ready to play, the play function starts from the beginning. The CD mode in the internal drive is possible if an audio CD for the navigation CD was inserted. If no navigation CD has been inserted, only a NO MAP route guidance is possible page 31. Do not make an attempt to insert the CD with force. If a CD changer * is connected, this one is selected first by pressing the button CD A10. CD functions (internal drive) Select track For selecting a track, press the right or left button A1 upwards or downwards. Fast station finding (audible) Press the right or left button A14 for a fast station finding upwards or downards. Playing all tracks on a CD (SCAN) Press the button SCAN A16. All tracks on a CD are briefly played in ascending order (10 seconds). SCAN is shown in the standard field - background - of the display. Press once again the button to interrupt this function. Listening to all tracks of a CD in the random sequence Press the button MIX A18.

20 Audio 19 Press the button MIX A18 once again to interrupt this function. Taking out the CD Press the button CD A10, the CD is driven to the initial position. Carefully remove the CD. End CD mode Select the desired range or allow the CD to eject with the button FM A2, TMC A5 or AM A6 Information on how to use a CD CD to jump Uneven road surfaces and strong vibrations may cause the CD to jump. In such cases wait with the CD mode until there is a better road surface to drive on. Formation of condensation When it is cold and after rain showers, moisture can deposit in the CD drive (condensation). This can effect the CD jump or impair the play function. In such cases wait until the moisture has dissipated. s for the care of the CDs If a CD is soiled, please never clean the CD in the direction of a circle but rather with a soft fluffly cloth from inside to outside. In case of severe layers of dirt we recommend to clean the CD with a commercially available CD cleaner. Also in this case do not clean the CD in the direction of a circle but rather from inside to outside and then let it dry off. Caution Never use liquids such as gasoline, paint thinner or disk cleaner, otherwise the surface of the CD could get damaged. Never expose CDs to direct sun rays! Please never write or affix the CD! Dirt or damage of a CD can lead to difficulties when reading the information. The difficulty in reading the error depends on the dirt or on the severity of the mechanical damage. Severe scratches cause reading errors which can make the CD jump or get stuck. All CDs must be treated carefully and always be stored in a protective case. Audio settings The treble and the bass as well as the volume distribution left/right (balance) and front/rear (fader) can be set in the sound menu. Press the button A24, to call up the sound menu. You can select the menu points to be selected one after each other with the menu knob A25. Set and confirm the new values with the menu knob A25. The setting is reset by pressing the button A27. After all settings have been carried out, exit the sound menu by pressing the button A27 or a an audio source button CD, FM, AM or TMC. The settings for treble and bass can be carried out and stored individually for each audio source, the settings for balance and fader apply to all audio sources. The fader setting is only available if loudspeakers are installed in the vehicle tailgate.

21 20 Navigation Navigation Overview of navigation basic menu Call up navigation basic menu SHOW LOCATION - display location determination, North and if necessary the name of the driven road DEST. MEMORY - store, edit or delete destinations in the destination memory TOURLIST page 35 TRAVEL GUIDE - Provide travel information (e.g. overnight price for hotels) to destinations page 35 GPS STATUS - shows the number of current GPS satellite receptions and the geographic position. Press the button NAVI A12. Fig. 10 Navigation basic menu If still no destination is entered, the selection marking is on the menu point SHOW LOCATION. If a destination has already been entered, the selection marking is on the menu point ROUTE GUIDANCE fig. 10. Select and confirm the menu points with the menu knob A25. You can return from the sub-menus, lists and types of display to the navigation basic menu by pressing the button NAVI A12. If you press the button NAVI A12 during an active route guidance, you can change between the route guidance and the navigation basic menu. Unavailable menu points are marked with a lock. In the navigation basic menu the following menus can be called up: ROUTE GUIDANCE page 31 STOP GUIDANCE page 32 ENTER DESTINATION - carry out via entry of destination address or from the destination memory page 21 ROUTE OPTIONS - select the dynamic route guidance or display the route list page 29 ROUTE LIST - calculate or display the route list page 30

22 Navigation 21 Enter Overview Call up the destination entry menu directly in the navigation basic menu. Enter destination - Town Select a town as destination You can first of all enter the desired town and then determine the destination with the menu point TOWN Fig. 11 Enter destination Fig. 12 Town as destination You can select via the menu points between the following possibilities of the destination entry: DEST. FROM MEMORY SPECIAL DESTINATION FLAG DEST. TOWN STREET TOWN CENTRE Select the menu point TOWN from fig. 12 in the destination entry menu with the menu knob A25. If you confirm the menu point TOWN, first of all you can enter the desired village and then determine the destination in the sub-menu ADDRESS ENTRY, to do so use one of the menu points STREET, TOWN CENTRE or CLOSE TO ADDRESS.

23 22 Navigation Editor Carry out with the editor all entries of names and numbers, which are required for the navigation. Entering a town name Fig. 14 Entering a town name Fig. 13 Editing menu Destination entry of e.g. town and street names Entry of a short name when storing a destination in the destination memory Entry of a short name for a flagged destination The editing menu consists of: a register with letters, characters and digits A, the control field AB, the editing field with standard names or the cursor AC, the area with a list entry (editing list) AD, the magnifying glass AE, here the currently marked letter is enlarged. Enter the initial letters of the name of the desired village in the editing field AC. With each new letter the next suitable entry is called up from the list and shown in the editing list AD. You have the possibility to quickly select the desired village without entering the complete name. To do so mark and confirm the desired characters with the menu knob A25. The character is entered into the editing field. Simultaneously the cursor jumps to a point towards the right. The next suitable entry is shown in the editing list AD. In case of an incorrect entry, you can delete the entered character with the button A23. Only names stored on the CD can be entered. Characters are faded out and indicated accordingly in the register A.

24 Navigation 23 Call up list The desired town is selected as destination with the aid of a list. You have two possibilities to call up the list via the editing menu. Press the menu knob A25 more than two seconds or mark and confirm the control field with the menu knob A25. Enter destination - Street - Intersection Select a street as destination Select street names from the list Select and confirm the desired entry with the menu knob A25. Scroll the list: by turning the menu knob A25 first move the selection marking onto the arrow and then over the first or last entry. Scroll line by line by moving the selection marking onto the arrow and then press the menu knob A25. With the button INFO A17 you can completely display a shortened list entry with... Determine the destination exactly The sub-menu ADDRESS ENTRY is displayed, if the destination town is determined. In this sub-menu you can determine your destination: STREET - allows the selection of a street and an intersection stated below, TOWN CENTRE - allows the selection of a town centre of the selected village, CLOSE TO ADDRESS - allows the selection of a destination close to the last entered destination. The selection is performed via columns, e.g. motorway connection point or shopping centre. The requirement is that the corresponding data is available on the navigation CD. Fig. 15 Select street as destination Mark and confirm the menu point STREET in the menu ENTER DESTINATION or in the following menu ADDRESS ENTRY with the menu knob A25. Enter the street name in the editing menu: Enter the street names in the editing field. Then call up the list by pressing on the menu knob A25 or mark and confirm the control field with the menu knob A25. Select street name from the list To do so mark and confirm the desired entry with the menu knob A25. The street sub-menu is called up.

25 24 Navigation Scroll the list: by turning the menu knob A25 first move the selection marking onto the arrow and then beyond the first or last entry. If the selected street name exists several times in a town, then a sub-menu is called up, from which the desired entry can be selected. In order to facilitate the search for long (consisting of several words) street names, these can be stored in some versions with different writing - full text search. If the menu point HOUSE NUMBER cannot be marked, data for this house number does not exist on the navigation CD. Enter destination - Town centre Select town centre (part of the town) as destination Enter intersection as destination Fig. 17 Select town centre as destination Fig. 16 Select intersection as destination The destination address can be precisely determined in the street sub-menu: INTERSECTION - calls up the editing menu/the list for selecting an intersection, HOUSE NUMBER - calls up the editing menu/the list for selecting a house number, CONTINUE - the menu ends and the navigation basic menu is called up. If the destination entry is concluded, you can start the ROUTE GUIDANCE page 31. For large towns you can enter the town centre of part of a town as destination using the menu point TOWN CENTRE. For small towns and villages this menu field is used for the entry of the town centre, as it is only possible to restrictively enter the destination via the menu field STREET. Select menu point TOWN CENTRE Mark and confirm the menu point TOWN CENTRE in the destination entry menu with the menu knob A25. Then a list (with maximum 20 entries) or the editing menu (with more than 20 entries) is called up.

26 Navigation 25 Selecting town centre Enter the name of the desired town centre in the editing field or confirm an existing entry. Select a list. Mark and confirm the desired town centre in the list with the menu knob A25. Then the navigation basic menu is called up. Change to ROUTE GUIDANCE page 31. For large towns also parts of the town are displayed in the list. If the selected town name (or name for part of the town) exists several times, then a sub-menu is called up, from which the desired entry can be selected. Destination entry - Special destination Enter special destinations Select menu field SPECIAL DESTINATION Mark and confirm the menu point SPECIAL DESTINATION in the destination entry menu. Special destinations are: CLOSE TO ADDRESS - Destinations close to the selected destination address (e. g. Car parks, Filling stations, Škoda Service Partner etc.) SUPREAREGIONAL DESTINATIONS - Destinations which have not been assigned to any specific village (e.g. border crossings, airports etc.), CLOSE TO LOCATION - Destinations close to the vehicle position. This type of special destination is suitable e.g. for the search of the next filling station or a Škoda Service Partner. The destination entry is made via columns which are stored in alphabetical order. Partially different columns as a selection are offered for the individual SPECIAL DESTINATION. Columns are e.g.: Exhibition regions, Motorway service, Car park/multi-storey car park, Škoda Service Partner. Columns, to which there is no data, are not shown. After selecting the column you can determine the desired address via the editing menu and the list. Fig. 18 Enter special destinations In case of more than 20 entries for one column, first of all the editing menu is called up. Enter here the desired name or its initial letter and then call up the list.

27 26 Navigation Enter destination - From destination memory Sort destinations in memory Store destination in the destination memory Select menu point STORE DESTINATION Confirm the menu point STORE DESTINATION. Then the editing menu is called up for the entry of a short name. Enter short name Enter the short name into the editing menu (e. g. AT HOME ). Press the menu knob A25 more than two seconds or mark and confirm the control field with the menu knob A25. A destination must first of all be stored in the destination memory, so that it can be used for a later destination entry. First of all a destination is stored in the alphabetical destination memory. Here the destination entries are alphabetically classified according to the short name (if you have given them a name); town name, street name, intersection etc... house number are stored. The destinations can be shown either in the order of their entry or alphabetically. A memory LAST DESTINATIONS is available for the destination entry from the destination memory. The last 10 destinations of the route guidance are stored here automatically. You can assign a short name (e.g. first name) to a destination. This makes it easier for you to later on fetch out the destination entry from the destination memory. If the destination memory can no longer take any other destinations, DESTI- NATION MEMORY IS ASSIGNED is displayed. Then you must delete one or several destinations. Fig. 19 Edit destinations in memory If you wish to use certain destinations frequently, it may be advantageous to store them according to classified criteria. Confirm the menu point SORT DESTINATIONS in the menu DESTINATION MEMORY. A list displays the destinations to be sorted. Mark and confirm a destination to be moved with the menu knob A25. Move the marked destination to the desired position by turning the menu knob A25. Confirm the new position with the menu knob A25.