TEST REPORT. Reference No... : WTS16S E V2 FCC ID... : 2AC7J-APACHEG6. Applicant... : idroid Inc.

Size: px

Start display at page:

Download "TEST REPORT. Reference No... : WTS16S E V2 FCC ID... : 2AC7J-APACHEG6. Applicant... : idroid Inc."

May Davis
5 years ago
Views:

TEST REPORT Reference No.... : WTS16S0755151-2E V2 FCC ID... : 2AC7J-APACHEG6 Applicant... : idroid Inc. Address.

.. : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced,

The report would be invalid without specific stamp of test institute and the signatures of compiler and approver.

1 TEST REPORT Reference No.... : WTS16S E V2 FCC ID... : 2AC7J-APACHEG6 Applicant... : idroid Inc. Address... : 1715 Mission Springs Dr.KATy. TEXAS USA Manufacturer... : idroid Inc. Address... : 1715 Mission Springs Dr.KATy. TEXAS USA Product Name... : Mobile Phone Model No.... : Apache G6 Brand. : idroid Standards... : FCC CFR47 Part :2015 Date of Receipt sample... : Jul. 07, 2016 Date of Test... : Jul. 09 Aug. 23, 2016 Date of Issue... : Aug. 23, 2016 Test Result... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel : Fax: Compiled by: Approved by: Zero Zhou / Test Engineer Philo Zhong / Manager Page 1 of 82

2 Reference No.: WTS16S E V2 Page 2 of 82 2 Test Summary Test Items Test Requirement Result Radiated Spurious Emissions (d) (a) (a) PASS Conducted Spurious Emissions (d) PASS Conducted Emissions (a) PASS 6dB Bandwidth (a)(2) PASS Maximum Peak Output Power (b)(3),(4) PASS Power Spectral Density (e) PASS Band Edge (d) PASS Antenna Requirement PASS Maximum Permissible Exposure (Exposure of Humans to RF Fields) (b)(1) PASS

3 Reference No.: WTS16S E V2 Page 3 of 82 3 Contents Page 1 COVER PAGE TEST SUMMARY CONTENTS REPORT REVISION HISTORY GENERAL INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T CHANNEL LIST TEST MODE TEST FACILITY EQUIPMENT USED DURING TEST EQUIPMENTS LIST DESCRIPTION OF SUPPORT UNITS MEASUREMENT UNCERTAINTY TEST EQUIPMENT CALIBRATION CONDUCTED EMISSION E.U.T. OPERATION EUT SETUP MEASUREMENT DESCRIPTION CONDUCTED EMISSION TEST RESULT RADIATED EMISSIONS EUT OPERATION TEST SETUP SPECTRUM ANALYZER SETUP TEST PROCEDURE CORRECTED AMPLITUDE & MARGIN CALCULATION SUMMARY OF TEST RESULTS CONDUCTED SPURIOUS EMISSIONS TEST PROCEDURE TEST RESULT BAND EDGE MEASUREMENT TEST PRODUCE TEST RESULT DB BANDWIDTH MEASUREMENT TEST PROCEDURE: TEST RESULT: MAXIMUM PEAK OUTPUT POWER TEST PROCEDURE: TEST RESULT: POWER SPECTRAL DENSITY TEST PROCEDURE: TEST RESULT: ANTENNA REQUIREMENT... 81

4 Reference No.: WTS16S E V2 Page 4 of RF EXPOSURE... 82

5 Reference No.: WTS16S E V2 Page 5 of 82 4 Report Revision History Report No. Report Version Description Issue Date WTS16S E NONE Original Aug. 05, 2016 WTS16S E V1 Version 1 Aug. 16, 2016 WTS16S E V2 Version 2 Aug. 23, 2016

6 Reference No.: WTS16S E V2 Page 6 of 82 5 General Information 5.1 General Description of E.U.T. Product Name :Mobile Phone Model No. : Apache G6 Model Description : N/A GSM Band(s) : GSM 850/900/1800/1900MHz GPRS Class : 12 WCDMA Band(s) : FDD Band II/V LTE Bnad(s) : N/A Wi-Fi Specification : 2.4G: b/g/n HT20 HT40 Bluetooth Version : Bluetooth v4.0 with BLE GPS : Support NFC : N/A Hardware Version : T822-W3-V Software Version Storage Location 5.2 Details of E.U.T. Operation Frequency Max. RF output power Type of Modulation Antenna installation : IDROID_APACHE_G6_V04_ _W822_1288_AW_YS : Internal Storage : GSM/GPRS 850: 824~849MHz PCS/GPRS1900: 1850~1910MHz WCDMA Band II: 1850~1910MHz WCDMA Band V: 824~849MHz WiFi: b/g/n HT20: 2412~2462MHz n HT40: 2422~2452MHz Bluetooth: 2402~2480MHz : GSM 850: 32.90dBm PCS1900:29.96dBm WCDMA Band II: 22.87dBm WCDMA Band V: 22.68dBm WiFi(2.4G): 9.33dBm Bluetooth: 0.88dBm : GSM,GPRS: GMSK WCDMA: BPSK WiFi: CCK, OFDM Bluetooth: GFSK, Pi/4 DQPSK,8DPSK : GSM/WCDMA: internal permanent antenna WiFi/Bluetooth: internal permanent antenna Antenna Gain :GSM 850: 1.3dBi

7 Reference No.: WTS16S E V2 Page 7 of 82 Technical Data Adapter 5.3 Channel List PCS1900: 1.1dBi WCDMA Band II: 1.1dBi WCDMA Band V: 1.3dBi WiFi(2.4G): 0.8dBi Bluetooth: 0.8dBi : Battery DC 3.8V, 3500mAh DC 5V, 1A, charging from adapter (Adapter Input: V~50/60Hz 0.2A) : Manufacture: idroid Inc. Model No.: Apache G6 WIFI Channel No. Frequency Channel Frequency Channel Frequency Channel (MHz) No. (MHz) No. (MHz) No Frequency (MHz) BT BLE Channel No. Frequency Channel Frequency Channel Frequency Channel (MHz) No. (MHz) No. (MHz) No Frequency (MHz)

8 Reference No.: WTS16S E V2 Page 8 of Test Mode Table 1 Tests Carried Out Under FCC part Test Items Mode Data Rate Channel TX/RX Maximum Peak Output Power Power Spectral Density 6dB Bandwidth Band Edge Transmitter Spurious Emissions b 11 Mbps 1/6/11 TX g 54 Mbps 1/6/11 TX n HT Mbps 1/6/11 TX n HT Mbps 3/6/9 TX b 11 Mbps 1/6/11 TX g 54 Mbps 1/6/11 TX n HT Mbps 1/6/11 TX n HT Mbps 3/6/9 TX b 11 Mbps 1/6/11 TX g 54 Mbps 1/6/11 TX n HT Mbps 1/6/11 TX n HT Mbps 3/6/9 TX b 11 Mbps 1/6/11 TX g 54 Mbps 1/6/11 TX n HT Mbps 1/6/11 TX n HT Mbps 3/6/9 TX b 11 Mbps 1/6/11 TX g 54 Mbps 1/6/11 TX n HT Mbps 1/6/11 TX n HT Mbps 3/6/9 TX Table 2 Tests Carried Out Under FCC part Test Items Mode Data Rate Channel TX/RX Maximum Peak Output Power BT BLE 1 Mbps 0/19/39 TX Power Spectral Density BT BLE 1 Mbps 0/19/39 TX 6dB Bandwidth BT BLE 1 Mbps 0/19/39 TX Band Edge BT BLE 1 Mbps 0/19/39 TX Transmitter Spurious Emissions BT BLE 1 Mbps 0/19/39 TX Note :Parameters set by test software during channel & power tests, the software provided by the customer was used to set the operating channels as well as the output power level. The RF output power set is the power expected by the manufacturer and is going to be fixed on the firmware of the final product.

9 Reference No.: WTS16S E V2 Page 9 of Test Facility The test facility has a test site registered with the following organizations: IC Registration No.: 7760A Waltek Services(Shenzhen) Co., Ltd. Has been registered and fully described in a report filed with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our files. Registration number 7760A, October 15, FCC Test Site 1# Registration No.: Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , April 29, FCC Test Site 2# Registration No.: Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , December 3, 2014.

10 Reference No.: WTS16S E V2 Page 10 of 82 6 Equipment Used during Test 6.1 Equipments List Conducted Emissions at Mains Terminals Disturbance Voltage Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. EMI Test Receiver R&S ESCI Sep.15,2015 Sep.14, LISN SCHWARZBECK NSLK Sep.15,2015 Sep.14, Limiter York MTS-IMP Sep.15,2015 Sep.14, Cable LARGE RF300 - Sep.15,2015 Sep.14,2016 3m Semi-anechoic Chamber for Radiation Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 EMC Analyzer Agilent E7405A MY Sep.15,2015 Sep.14, Active Loop Antenna Trilog Broadband Antenna Coaxial Cable (below 1GHz) Broad-band Horn Antenna Broad-band Horn Antenna Broadband Preamplifier Coaxial Cable (above 1GHz) Broad-band Horn Antenna Universal Radio Communication Tester Beijing Dazhi ZN30900A - Sep.15,2015 Sep.14,2016 SCHWARZBECK VULB Apr.18,2016 Apr.17,2017 Top TYPE16(13M) - Sep.15,2015 Sep.14,2016 SCHWARZBECK BBHA 9120 D 667 Apr.18,2016 Apr.17,2017 SCHWARZBECK BBHA 9120 D 669 Apr.18,2016 Apr.17,2017 COMPLIANCE DIRECTION PAP-1G Mar.17,2016 Mar.16,2017 Top 1000MHz-25GHz EW Apr.09,2016 Apr.08,2017 SCHWARZBECK BBHA Sep.15,2015 Sep.14,2016 R&S CMU Apr.10,2016 Apr.09, Signal Generator R&S SMR Sep.15,2015 Sep.14,2016 RF Conducted Testing Item Equipment Manufacturer Model No. Serial No EMC Analyzer (9k~26.5GHz) Spectrum Analyzer (9k-6GHz) Last Calibration Date Calibration Due Date Agilent E7405A MY Sep.15,2015 Sep.14,2016 R&S FSL Sep.15,2015 Sep.14, Humidity Chamber GF GTH P IAA Sep.15,2015 Sep.14,2016

11 Reference No.: WTS16S E V2 Page 11 of Description of Support Units Equipment Manufacturer Model No. Series No. / / / / 6.3 Measurement Uncertainty Parameter Uncertainty Radio Frequency ± 1 x 10-6 RF Power RF Power Density Radiated Spurious Emissions test Conducted Spurious Emissions test 6.4 Test Equipment Calibration ± 1.0 db ± 2.2 db ± 5.03 db (30M~1000MHz) ± 5.47 db (1000M~25000MHz) ± 3.64 db (AC mains 150KHz~30MHz) All the test equipments used are valid and calibrated by CEPREI Certification Body that address is No.110 Dongguan Zhuang RD. Guangzhou, P.R.China.

12 Reference No.: WTS16S E V2 Page 12 of 82 7 Conducted Emission Test Requirement: FCC CFR 47 Part 15 Section Test Method: ANSI C63.10:2013 Test Result: PASS Frequency Range: 150kHz to 30MHz Class/Severity: Class B Limit: db V between 0.15MHz & 0.5MHz 56 db V between 0.5MHz & 5MHz 60 db V between 5MHz & 30MHz Detector: Peak for pre-scan (9kHz Resolution Bandwidth) 7.1 E.U.T. Operation Operating Environment : Temperature: Humidity: Atmospheric Pressure: 21.5 C 51.9 % RH 101.2kPa EUT Operation : The test was performed in WIFI link mode, the worst data were shown in the report. 7.2 EUT Setup The conducted emission tests were performed using the setup accordance with the ANSI C m 0.8m EUT Receiver PC System 0.8m LISN :50 Terminator 7.3 Measurement Description The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within 6dB of the average limit line.

13 Reference No.: WTS16S E V2 Page 13 of Conducted Emission Test Result An initial pre-scan was performed on the live and neutral lines. Worst Mode: WIFI mode Live line:

14 Reference No.: WTS16S E V2 Page 14 of 82 Neutral line:

15 Reference No.: WTS16S E V2 Page 15 of 82 Worst Mode: BLE mode Live line:

16 Reference No.: WTS16S E V2 Page 16 of 82 Neutral line:

17 Reference No.: WTS16S E V2 Page 17 of 82 8 Radiated Emissions Test Requirement: FCC CFR47 Part 15 Section & Test Method: ANSI C63.10:2013 Test Result: PASS Measurement Distance: 3m Limit: Field Strength Field Strength Limit at 3m Measurement Dist Frequency Distance (MHz) uv/m uv/m dbuv/m (m) ~ /F(kHz) * 2400/F(kHz) 20log (2400/F(kHz)) ~ /F(kHz) * 24000/F(kHz) 20log (24000/F(kHz)) ~ * 30 20log (30) ~ log (100) 88 ~ log (150) 216 ~ log (200) Above log (500) 8.1 EUT Operation Operating Environment : Temperature: Humidity: Atmospheric Pressure: 23.5 C 52.1 % RH 101.2kPa EUT Operation : The test was performed in WIFI link mode, the test data were shown in the report.

18 Reference No.: WTS16S E V2 Page 18 of Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the ANSI C The test setup for emission measurement below 30MHz. Semi-anechoic 3m Chamber Turn Table From 0 to 360 EUT 3m 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network The test setup for emission measurement from 30 MHz to 1 GHz. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network

19 Reference No.: WTS16S E V2 Page 19 of 82 The test setup for emission measurement above 1 GHz. Anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network 8.3 Spectrum Analyzer Setup Below 30MHz Sweep Speed... Auto IF Bandwidth... 10kHz Video Bandwidth... 10kHz Resolution Bandwidth... 10kHz 30MHz ~ 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth kHz Video Bandwidth kHz Above 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth... 1MHz Video Bandwidth... 3MHz Detector... Ave. Resolution Bandwidth... 1MHz Video Bandwidth... 10Hz

20 Reference No.: WTS16S E V2 Page 20 of Test Procedure 1. The EUT is placed on a turntable, which is 0.8m(30M-1GHz) 1.5m(above 1GHz) above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The radiation measurements are performed in X,Y and Z axis positioning(x denotes lying on the table, Y denotes side stand and Z denotes vertical stand),the worst condition was tested putting the eut in X axis,so the worst data were shown as follow. 8. A 2.4GHz high pass filter is used druing radiated emissions above 1GHz measurement. 8.5 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Antenna Factor + Cable Factor - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the maximum limit for Class B. The equation for margin calculation is as follows: Margin = Corr. Ampl. Limit

21 Reference No.: WTS16S E V2 Page 21 of Summary of Test Results Wifi: Test Frequency: 9KHz~30MHz Remark: only the worst data (802.11n HT40 mode) were reported Frequency Measurement results Detector PK/QP Correct factor db/m Extrapolatio n factor db Measurement results (calculated) Limits Margi n db (MHz) Measurement results Detector Correct factor Extrapolatio n factor Measurement results (calculated) Limits Margi n QP QP QP

22 Reference No.: WTS16S E V2 Page 22 of 82 Test Frequency : 30MHz ~ 1GHz Remark: only the worst data (802.11n HT40 mode) were reported 11n HT40: Low Channel Horizontal 11n HT40: Low Channel Vertical

23 Reference No.: WTS16S E V2 Page 23 of 82 11n HT40: Middle Channel Horizontal 11n HT40: Middle Channel Vertical

24 Reference No.: WTS16S E V2 Page 24 of 82 11n HT40: High Channel Horizontal 11n HT40: High Channel Vertical

25 Reference No.: WTS16S E V2 Page 25 of 82 Test Frequency : Above 1GHzRemark: only the worst data (802.11n HT40 mode) were reported 11n HT40: Low Channel Horizontal 11n HT40: Low Channel Vertical

26 Reference No.: WTS16S E V2 Page 26 of 82 11n HT40: Middle Channel Horizontal 11n HT40: Middle Channel Vertical

27 Reference No.: WTS16S E V2 Page 27 of 82 11n HT40: High Channel - Horizontal 11n HT40: High Channel - Vertical

28 Reference No.: WTS16S E V2 Page 28 of 82 9 Conducted Spurious Emissions Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r04 January 7, 2016 Test Result: PASS Limit: In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in Section (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section (a), must also comply with the radiated emission limits specified in Section (a) (see Section (c)). 9.1 Test Procedure 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum; 2. Set the spectrum analyzer: RBW = 100kHz, VBW = 300kHz, Sweep = auto Detector function = peak, Trace = max hold

Reference No.: WTS16S0755151-2E V2 Page 29 of 82 9.

29 Reference No.: WTS16S E V2 Page 29 of Test Result b Low Channel Fundamental Middle Channel Fundamental

30 Reference No.: WTS16S E V2 Page 30 of 82 High Channel Fundamental g Low Channel Fundamental

31 Reference No.: WTS16S E V2 Page 31 of 82 Middle Channel Fundamental High Channel Fundamental

32 Reference No.: WTS16S E V2 Page 32 of n HT20 Low Channel Fundamental Middle Channel Fundamental

33 Reference No.: WTS16S E V2 Page 33 of 82 High Channel Fundamental n HT40 Low Channel Fundamental

34 Reference No.: WTS16S E V2 Page 34 of 82 Middle Channel Fundamental High Channel Fundamental

35 Reference No.: WTS16S E V2 Page 35 of 82 BLE Low Channel Fundamental Middle Channel Fundamental

36 Reference No.: WTS16S E V2 Page 36 of 82 High Channel Fundamental

37 Reference No.: WTS16S E V2 Page 37 of Band Edge Measurement Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r04 January 7, 2016 Test Limit: Regulation (d),in any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in (a), must also comply with the radiated emission limits specified in (a) (see (c)). Test Mode: Transmitting 10.1 Test Produce 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. 3. Set RBW to 100 khz and VBW of spectrum analyzer to 300 khz with a convenient frequency span including 100 khz bandwidth from band edge. 4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. 5. Repeat above procedures until all measured frequencies were complete.

Reference No.: WTS16S0755151-2E V2 Page 38 of 82 10.

38 Reference No.: WTS16S E V2 Page 38 of Test Result Test result plots shown as follows: TX 11b: Band edge-left side TX 11b: Band edge-right side

39 Reference No.: WTS16S E V2 Page 39 of 82 TX 11g: Band edge-left side TX 11g: Band edge-right side

40 Reference No.: WTS16S E V2 Page 40 of 82 TX 11n HT20: Band edge-left side TX 11n HT20: Band edge-right side

41 Reference No.: WTS16S E V2 Page 41 of 82 TX 11n HT40: Band edge-left side TX 11n HT40: Band edge-right side

42 Reference No.: WTS16S E V2 Page 42 of 82 BLE: Band edge-left side BLE: Band edge-right side

43 Reference No.: WTS16S E V2 Page 43 of 82 TX 11b: Band edge-left side Horizontal TX 11b: Band edge-left side Vertical

44 Reference No.: WTS16S E V2 Page 44 of 82 TX 11b: Band edge-right side Horizontal TX 11b: Band edge-right side Vertical

45 Reference No.: WTS16S E V2 Page 45 of 82 TX 11g: Band edge-left side Horizontal TX 11g: Band edge-left side Vertical

46 Reference No.: WTS16S E V2 Page 46 of 82 TX 11g: Band edge-right side Horizontal TX 11g: Band edge-right side Vertical

47 Reference No.: WTS16S E V2 Page 47 of 82 TX 11n HT20: Band edge-left side Horizontal TX 11n HT20: Band edge-left side Vertical

48 Reference No.: WTS16S E V2 Page 48 of 82 TX 11n HT20: Band edge-right side Horizontal TX 11n HT20: Band edge-right side Vertical

49 Reference No.: WTS16S E V2 Page 49 of 82 TX 11n HT40: Band edge-left side Horizontal TX 11n HT40: Band edge-left side Vertical

50 Reference No.: WTS16S E V2 Page 50 of 82 TX 11n HT40: Band edge-right side Horizontal TX 11n HT40: Band edge-right side Vertical

51 Reference No.: WTS16S E V2 Page 51 of 82 BLE: Band edge-left side Horizontal BLE: Band edge-left side Vertical

52 Reference No.: WTS16S E V2 Page 52 of 82 BLE: Band edge-right side Horizontal BLE: Band edge-right side Vertical

53 Reference No.: WTS16S E V2 Page 53 of db Bandwidth Measurement Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r04 January 7, Test Procedure: 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum; 2. Set the spectrum analyzer: RBW = 100kHz, VBW = 300kHz 11.2 Test Result: Operation mode TX 11b TX 11g TX 11n HT20 TX 11n HT40 BLE Bandwidth (MHz) Channel 1 Channel 6 Channel Channel 1 Channel 6 Channel Channel 1 Channel 6 Channel Channel 3 Channel 6 Channel Channel 0 Channel 19 Channel

54 Reference No.: WTS16S E V2 Page 54 of 82 Test result plot as follows: Mode: TX 11b channel 1 Mode: TX 11b channel 6

55 Reference No.: WTS16S E V2 Page 55 of 82 Mode: TX 11b channel 11 Mode: TX 11g channel 1

56 Reference No.: WTS16S E V2 Page 56 of 82 Mode: TX 11g channel 6 Mode: TX 11g channel 11

57 Reference No.: WTS16S E V2 Page 57 of 82 Mode: TX 11n HT20 channel 1 Mode: TX 11n HT20 channel 6

58 Reference No.: WTS16S E V2 Page 58 of 82 Mode: TX 11n HT20 channel 11 Mode: TX 11n HT40 channel 3

59 Reference No.: WTS16S E V2 Page 59 of 82 Mode: TX 11n HT40 channel 6 Mode: TX 11n HT40 channel 9

60 Reference No.: WTS16S E V2 Page 60 of 82 BLE: channel 0 BLE: channel 19

61 Reference No.: WTS16S E V2 Page 61 of 82 BLE: channel 39

62 Reference No.: WTS16S E V2 Page 62 of Maximum Peak Output Power Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r04 January 7, Test Procedure: KDB D01 DTS Meas Guidance v03r04 January 7, 2016 section (For BLE) This procedure shall be used when the measurement instrument has available a resolution bandwidth that is greater than the DTS bandwidth. a)set the RBW DTS bandwidth. b)set VBW 3 RBW. c)set span 3 x RBW d)sweep time = auto couple. e)detector = peak. f)trace mode = max hold. g)allow trace to fully stabilize. h)use peak marker function to determine the peak amplitude level. section (For WIFI) This procedure may be used when the maximum available RBW of the measurement instrument is less than the DTS bandwidth. a)set the RBW = 1 MHz. b)set the VBW 3 RBW c)set the span 1.5 x DTS bandwidth. d)detector = peak. e)sweep time = auto couple. f)trace mode = max hold. g)allow trace to fully stabilize. h)use the instrument s band/channel power measurement function with the band limits set equal to the DTS bandwidth edges (for some instruments, this may require a manual override to select peak detector). If the instrument does not have a band power function, sum the spectrum levels (in linear power units) at intervals equal to the RBW extending across the DTS bandwidth.

63 Reference No.: WTS16S E V2 Page 63 of Test Result: Test mode :TX 11b Maximum Peak Output Power (dbm) 2412MHz 2437MHz 2462MHz Limit: 1W/30dBm Test mode :TX 11g Maximum Peak Output Power (dbm) 2412MHz 2437MHz 2462MHz Limit: 1W/30dBm Test mode :TX 11n HT20 Maximum Peak Output Power (dbm) 2412MHz 2437MHz 2462MHz Limit: 1W/30dBm Test mode :TX 11n HT40 Maximum Peak Output Power (dbm) 2422MHz 2437MHz 2452MHz Limit: 1W/30dBm BLE Maximum Peak Output Power (dbm) 2402MHz 2440MHz 2480MHz Limit: 1W/30dBm

64 Reference No.: WTS16S E V2 Page 64 of 82 Mode: TX 11b channel 1 Mode: TX 11b channel 6

65 Reference No.: WTS16S E V2 Page 65 of 82 Mode: TX 11b channel 11 Mode :TX 11g channel 1

66 Reference No.: WTS16S E V2 Page 66 of 82 Mode :TX 11g channel 6 Mode :TX 11g channel 11

67 Reference No.: WTS16S E V2 Page 67 of 82 Mode: TX 11n HT20 channel 1 Mode: TX 11n HT20 channel 6

68 Reference No.: WTS16S E V2 Page 68 of 82 Mode: TX 11n HT20 channel 11 Mode: TX 11n HT40 channel 1

69 Reference No.: WTS16S E V2 Page 69 of 82 Mode: TX 11n HT40 channel 6 Mode: TX 11n HT40 channel 11

70 Reference No.: WTS16S E V2 Page 70 of 82 BLE: channel 0 BLE: channel 19

71 Reference No.: WTS16S E V2 Page 71 of 82 BLE: channel 39

72 Reference No.: WTS16S E V2 Page 72 of Power Spectral density Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r04 January 7, Test Procedure: KDB D01 DTS Meas Guidance v03r04 January 7, 2016 section Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum. 2. Set the spectrum analyzer: RBW = 3kHz. VBW = 10kHz, Span = 1.5 times the DTS channel bandwidth(6 db bandwidth). Sweep = auto; Detector Function = Peak. Trace = Max hold. 3. Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. The limit is specified in one of the subparagraphs of this Section Submit this plot Test Result: Test mode :TX 11b Power Spectral (dbm per 3kHz) 2412MHz 2437MHz 2462MHz Limit: 8dBm per 3kHz Test mode :TX 11g Power Spectral (dbm per 3kHz) 2412MHz 2437MHz 2462MHz Limit: 8dBm per 3kHz Test mode :TX 11n HT20 Power Spectral (dbm per 3kHz) 2412MHz 2437MHz 2462MHz Limit: 8dBm per 3kHz Test mode :TX 11n HT40 Power Spectral (dbm per 3kHz) 2422MHz 2437MHz 2452MHz Limit: 8dBm per 3kHz

73 Reference No.: WTS16S E V2 Page 73 of 82 BLE Power Spectral (dbm per 3kHz) 2402MHz 2440MHz 2480MHz Limit: 8dBm per 3kHz Mode: TX 11b channel 1

74 Reference No.: WTS16S E V2 Page 74 of 82 Mode: TX 11b channel 6 Mode: TX 11b channel 11

75 Reference No.: WTS16S E V2 Page 75 of 82 Mode :TX 11g channel 1 Mode :TX 11g channel 6

76 Reference No.: WTS16S E V2 Page 76 of 82 Mode :TX 11g channel 11 Mode: TX 11n HT20 channel 1

77 Reference No.: WTS16S E V2 Page 77 of 82 Mode: TX 11n HT20 channel 6 Mode: TX 11n HT20 channel 11

78 Reference No.: WTS16S E V2 Page 78 of 82 Mode: TX 11n HT40 channel 3 Mode: TX 11n HT40 channel 6

79 Reference No.: WTS16S E V2 Page 79 of 82 Mode: TX 11n HT40 channel 9 BLE: channel 0

80 Reference No.: WTS16S E V2 Page 80 of 82 BLE: channel 19 BLE: channel 39

81 Reference No.: WTS16S E V2 Page 81 of Antenna Requirement According to the FCC Part 15 Paragraph , an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. This product has an integrated antenna fulfill the requirement of this section.

82 Reference No.: WTS16S E V2 Page 82 of RF Exposure Remark: refer to SAR test report: WTS16S E ======End of Report======

TEST REPORT. Reference No... : WTS16S E FCC ID... : SJ8-UDR777HD. Applicant... : RDI Technology Shenzhen Co., Ltd.

TEST REPORT. Reference No... : WTS16S E FCC ID... : SJ8-UDR777HD. Applicant... : RDI Technology Shenzhen Co., Ltd. TEST REPORT Reference No.... : WTS16S0449305E FCC ID... : SJ8-UDR777HD Applicant... : RDI Technology Shenzhen Co., Ltd. Address... : Building C1, Xintang Industrial Park East Baishixia, Fuyong, Baoan,