FCC Part 15C Test Report FCC ID: 2ANYRCBAR-25

Transcription

1 FCC Part 15C Test Report FCC ID: 2ANYRCBAR-25 Product Name: Bluetooth Module Trademark: Model Name : Prepared For : Address : CBAR-25 PT. Eyro Digital Teknologi Jl, Amir Mahmud IX/23 Gunung Anyar, Surabaya 60294, Indonesia Prepared By : Address : Shenzhen BCTC Testing Co., Ltd. BCTC Building & 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao'an District, Shenzhen, China Test Date: Oct. 24, 2017 Oct. 30, 2017 Date of Report : Oct. 30, 2017 Report No.: BCTC-LH E FCC Report Tel: Web: Page1 of 39

2 TEST RESULT CERTIFICATION Applicant s name... : PT. Eyro Digital Teknologi Address... : Jl, Amir Mahmud IX/23 Gunung Anyar, Surabaya 60294, Indonesia Manufacture's Name... : PT. Eyro Digital Teknologi Address... : Jl, Amir Mahmud IX/23 Gunung Anyar, Surabaya 60294, Indonesia Product description Product name... : Bluetooth Module Trademark... : Model and/or type reference : CBAR-25 Standards... : FCC Part Test procedure...ansi C This device described above has been tested by BCTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of BCTC, this document may be altered or revised by BCTC, personal only, and shall be noted in the revision of the document. Prepared by(engineer): Snow Zeng Reviewer(Supervisor): Jade Yang Approved(Manager): Carson Zhang EMC Report Tel: Web: Page 2 of 39

3 Table of Contents Page 1. SUMMARY OF TEST RESULTS TEST FACILITY MEASUREMENT UNCERTAINTY 6 2. GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) EQUIPMENTS LIST FOR ALL TEST ITEMS EMC EMISSION TEST CONDUCTED EMISSION MEASUREMENT POWER LINE CONDUCTED EMISSION LIMITS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS RADIATED EMISSION MEASUREMENT RADIATED EMISSION LIMITS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS (BETWEEN 9KHZ 30 MHZ) TEST RESULTS (BETWEEN 30MHZ 1GHZ) TEST RESULTS (1GHZ~25GHZ) POWER SPECTRAL DENSITY TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS 26 EMC Report Tel: Web: Page 3 of 39

4 Table of Contents Page 5. BANDWIDTH TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS PEAK OUTPUT POWER TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS KHZ BANDWIDTH OF FREQUENCY BAND EDGE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS ANTENNA REQUIREMENT STANDARD REQUIREMENT EUT ANTENNA TEST SEUUP PHOTO EUT PHOTO 39 EMC Report Tel: Web: Page 4 of 39

5 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: Standard Section FCC Part15 (15.247), Subpart C Test Item Judgment Remark Conducted Emission N/A (a)(2) 6dB Bandwidth PASS (b) Peak Output Power PASS (c) Radiated Spurious Emission PASS (d) Power Spectral Density PASS Band Edge Emission PASS Antenna Requirement PASS NOTE: (1) N/A denotes test is not applicable in this Test Report EMC Report Tel: Web: Page 5 of 39

6 1.1 TEST FACILITY Shenzhen BCTC Testing Co., Ltd. Add. : BCTC Building & 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao'an District, Shenzhen, China FCC Registered No.: MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U,where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of approximately 95 % No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1g) ±4.68dB 5 All emissions,radiated(>1g) ±4.89dB 6 Temperature ±0.5 C 7 Humidity ±2% EMC Report Tel: Web: Page 6 of 39

7 2. GENERAL INFORMATION Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC-LH E 2.1 GENERAL DESCRIPTION OF EUT Equipment Bluetooth Module Trade Name Model Name Model Difference Product Description CBAR-25 N/A The EUT is a Bluetooth Module Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Bit Rate of Transmitter 1Mbps Number Of Channel 40 CH Antenna type: PCB antenna Antenna Gain (dbi) 0dBi Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Channel List Please refer to the Note 2. Power hardware version -- Software version -- Serial number -- Connecting I/O Port(s) DC 3V Please refer to the User's Manual Note: 1. For a more detailed features description, please refer to the manufacturer s specifications or the User's Manual. 2. Channel List Frequency (MHz) Channel ~ ~ ~ ~ Channel Frequency (MHz) Channel Frequency (MHz) EMC Report Tel: Web: Page 7 of 39

8 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Mode 1 Mode 2 Mode 3 Mode 4 Description CH01 CH20 CH40 Link Mode For Radiated Emission Final Test Mode Mode 1 Mode 2 Description CH01 CH20 Mode 3 CH40 Note: (1) The measurements are performed at the highest, middle, lowest available channels. (2) For all test, used new battery. (3) The client provide 6 pcs fix frequency sample. EMC Report Tel: Web: Page 8 of 39

9 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED Radiated Spurious Emission Test E-1 EUT 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note E-1 Bluetooth Module N/A CBAR-25 N/A EUT Item Shielded Type Ferrite Core Length Note Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in Length column. EMC Report Tel: Web: Page 9 of 39

10 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation test, Band-edge test and 6db bandwidth test equipment Item Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until 1 Spectrum Analyzer Agilent E4407B MY (9kHz-26.5GHz) 2 Test Receiver (9kHz-7GHz) R&S ESPI Bilog Antenna VULB VULB91 R&S (30MHz-1GHz) Horn Antenna (1GHz-18GHz) SCHWARZBECK BBHA9120D Horn Antenna SCHWARZBECK (14GHz-40GHz) BBHA Amplifier (9KHz-6GHz) SCHWARZBECK BBV Amplifier (1GHz-18GHz) SCHWARZBECK BBV Amplifier SCHWARZBECK (18GHz-40GHz) BBV Loop Antenna (9KHz-30MHz) SCHWARZBECK FMZB1519B RF cables1 (9kHz-1GHz) R&S R203 R20X RF cables2 (1GHz-40GHz) R&S R204 R21X Antenna connector Florida RF Labs N/A RF 01# Power Metter ANRITSU ML2487A 6K Power Sensor (AV) Signal Analyzer 9kHz-26.5GHz Test Receiver 20kHz-40GHz D.C. Power Supply Conduction Test equipment ANRITSU ML2491A Agilent N9010A MY R&S ESU LongWei PS-305D Item Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until 1 Test Receiver R&S ESCI K ha LISN SCHWARZBECK NSLK LISN R&S NSLK RF cables R&S R204 R20X Attenuator R&S ESH3-Z EMC Report Tel: Web: Page 10 of 39

11 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT POWER LINE CONDUCTED EMISSION Limits (Frequency Range 150KHz-30MHz) FREQUENCY (MHz) Quasi-peak Limit (dbuv) Average Standard * * FCC FCC FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Attenuation Start Frequency Stop Frequency IF Bandwidth Setting 10 db 0.15 MHz 30 MHz 9 khz EMC Report Tel: Web: Page 11 of 39

12 3.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item EUT Test Photos DEVIATION FROM TEST STANDARD No deviation TEST SETUP V e r t ic a l R e f e r e n c e G r o u n d P la n e T e s t R e c e i v e r 4 0 c m E U T L IS N 8 0 c m N o t e : 1.S u p p o r t u n its w e r e c o n n e c t e d t o s e c o n d L I S N. 2.B o t h o f L IS N s ( A M N ) a r e 8 0 c m f r o m E U T a n d a t l e a s t 8 0 f r o m o t h e r u n its a n d o t h e r m e ta l p l a n e s H o r i z o n ta l R e f e r e n c e G r o u n d P l a n e EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data TEST RESULTS The EUT's power provide by battery, no requriments for this item. EMC Report Tel: Web: Page 12 of 39

13 3.2 RADIATED EMISSION MEASUREMENT RADIATED EMISSION LIMITS (Frequency Range 9kHz-1000MHz) In case the emission fall within the restricted band specified on (a), then the (a) limit in the table below has to be followed. Frequencies (MHz) Field Strength (micorvolts/meter) Measurement Distance (meters) 0.009~ /F(KHz) ~ /F(KHz) ~ ~ ~ ~ Above LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) FREQUENCY (MHz) PEAK Limit (dbuv/m) (at 3M) AVERAGE Above Notes: (1) The limit for radiated test was performed according to FCC PART 15C. (2) The tighter limit applies at the band edges. (3) Emission level (dbuv/m)=20log Emission level (uv/m). Spectrum Parameter Attenuation Start Frequency Stop Frequency RB / VB (emission in restricted band) Setting Auto 1000 MHz 25GHz 1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for Average Receiver Parameter Attenuation Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Setting Auto 9kHz~150kHz / RB 200Hz for QP 150kHz~30MHz / RB 9kHz for QP 30MHz~1000MHz / RB 120kHz for QP EMC Report Tel: Web: Page 13 of 39

14 3.2.2 TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported DEVIATION FROM TEST STANDARD No deviation TEST SETUP (A)Radiated Emission Test-Up Frequency Below 30MHz Semi-anechoic 3m Chamber Turn Table From 0 to 360 EUT 3m 0.8m Turn Table PC System Spectrum AMP Combining Analyzer Network EMC Report Tel: Web: Page 14 of 39

15 (B)Radiated Emission Test-Up Frequency 30MHz~1GHz Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network (C)Radiated Emission Test-Up Frequency Above 1GHz Aechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. EMC Report Tel: Web: Page 15 of 39

16 3.2.6 TEST RESULTS (BETWEEN 9KHZ 30 MHZ) Temperature: 20 Relative Humidtity: 48% Pressure: 1010 hpa Test Voltage : DC 3.0V Test Mode : Mode 4 Polarization : -- Freq. Reading Limit Margin State (MHz) (dbuv/m) (dbuv/m) (db) P/F PASS PASS NOTE: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(db); Limit line = specific limits(dbuv) + distance extrapolation factor. EMC Report Tel: Web: Page 16 of 39

17 3.2.7 TEST RESULTS (BETWEEN 30MHZ 1GHZ) Temperature: 26 Relative Humidity: 54% Pressure: 1010 hpa Polarization : Horizontal Test Voltage : DC 3.0V Test Mode : Mode 4 Remark: Factor = Antenna Factor + Cable Loss Pre-amplifier. EMC Report Tel: Web: Page 17 of 39

18 Temperature: 26 Relative Humidity: 54% Pressure: 1010 hpa Polarization : Vertical Test Voltage : DC 3.0V Test Mode : Mode 4 Remark: Factor = Antenna Factor + Cable Loss Pre-amplifier. EMC Report Tel: Web: Page 18 of 39

19 3.2.8 TEST RESULTS (1GHZ~25GHZ) Polar (H/V) Frequency Meter Reading Pre- amplifier Cable Loss Antenna Factor Emission Level Limits Margin Detector Type (MHz) (dbuv) (db) (db) (db/m) (dbuv/m) (dbuv/m) (db) operation frequency:2402 V PK V AV V PK V AV V PK H PK H AV H PK H AV H PK operation frequency:2440 V PK V AV V PK V AV V PK H PK H AV H PK H AV H PK operation frequency:2480 V PK V AV V PK V AV V PK H PK H AV H PK H AV H PK Remark: 1. Emission Level = Meter Reading + Antenna Factor + Cable Loss Pre-amplifier, Margin= Emission Level - Limit 2. If peak below the average limit, the average emission was no test. 3. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. EMC Report Tel: Web: Page 19 of 39

20 For conducted 2402MHz 2440MHz 2480MHz EMC Report Tel: Web: Page 20 of 39

21 3.3 RADIATED BAND EMISSION MEASUREMENT TEST REQUIREMENT: FCC Part15 C Section and LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) FREQUENCY (MHz) PEAK Limit (dbuv/m) (at 3M) AVERAGE Above Notes: (1) The limit for radiated test was performed according to FCC PART 15C. (2) The tighter limit applies at the band edges. (3) Emission level (dbuv/m)=20log Emission level (uv/m). Spectrum Parameter Attenuation Start Frequency Setting Auto 2300MHz Stop Frequency 2520 RB / VB (emission in restricted band) 1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for Average TEST PROCEDURE Above 1GHz test procedure as below: a. 1. The EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. g. Test the EUT in the lowest channel,the Highest channel Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported EMC Report Tel: Web: Page 21 of 39

22 3.3.3 DEVIATION FROM TEST STANDARD No deviation TEST SETUP Radiated Emission Test-Up Frequency Above 1GHz Aechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing. The plot only show the Horizontal's average data. EMC Report Tel: Web: Page 22 of 39

23 3.3.6 TEST RESULT Polar (H/V) Meter Pre- Cable Antenna Emission Frequency Reading amplifier Loss Factor evel Limits Margin Detector (MHz) (dbuv) (db) (db) (db/m) (dbuv/m) (dbuv/m (db) operation frequency:2402 Type V PK V AV V PK V AV H PK H AV H PK H AV Remark: 1. Emission Level = Meter Reading + Factor, Margin= Emission Level - Limit 2. If peak below the average limit, the average emission was no test. 3. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. EMC Report Tel: Web: Page 23 of 39

24 Polar (H/V) Meter Pre- Cable Antenna Emission Frequency Reading amplifier Loss Factor Level Limits Margin Detector (MHz) (dbuv) (db) (db) (db/m) (dbuv/m) (dbuv/m) (db) operation frequency:2480 Type V PK V AV V PK V AV H PK H AV H PK H AV Remark: 1. Emission Level = Meter Reading + Factor, Margin= Emission Level - Limit 2. If peak below the average limit, the average emission was no test. 3. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. EMC Report Tel: Web: Page 24 of 39

25 4. POWER SPECTRAL DENSITY TEST 4.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit Power Spectral Density 8 dbm (in any 3KHz) Frequency Range (MHz) Result PASS TEST PROCEDURE 1. Set analyzer center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS bandwidth. 3. Set the RBW to: 3 khz RBW 100 khz. 4. Set the VBW 3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level within the RBW. 10. If measured value exceeds limit, reduce RBW (no less than 3 khz) and repeat DEVIATION FROM STANDARD No deviation TEST SETUP EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.1 Unless otherwise a special operating condition is specified in the follows during the testing. EMC Report Tel: Web: Page 25 of 39

26 4.1.5 TEST RESULTS Temperature: 25 Relative Humidity: 60% Pressure: 1015 hpa Test Voltage : DC 3.0V Test Mode : TX Mode /CH01, CH20, CH40 Frequency Power Density (dbm) Limit (dbm) Result 2402 MHz <8 PASS 2440 MHz <8 PASS 2480 MHz <8 PASS TX CH01 EMC Report Tel: Web: Page 26 of 39

27 TX CH20 TX CH40 EMC Report Tel: Web: Page 27 of 39

28 5. BANDWIDTH TEST 5.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit Frequency Range (MHz) Result (a)(2) Bandwidth >= 500KHz (6dB bandwidth) PASS TEST PROCEDURE 1. Set RBW = 100 khz. 2. Set the video bandwidth (VBW) 3 x RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 db relative to the maximum level measured in the fundamental emission DEVIATION FROM STANDARD No deviation TEST SETUP EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. EMC Report Tel: Web: Page 28 of 39

29 5.1.5 TEST RESULTS Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC-LH E Temperature: 25 Relative Humidity: 60% Pressure: 1012 hpa Test Voltage : DC 3.0V Test Mode : TX Mode /CH01, CH20, CH40 Channel Frequency (MHz) 6dB bandwidth (KHz) Limit (khz) Result Low >500 Pass Middle >500 Pass High >500 Pass TX CH 01 EMC Report Tel: Web: Page 29 of 39

30 TX CH 20 TX CH 40 EMC Report Tel: Web: Page 30 of 39

31 6. PEAK OUTPUT POWER TEST 6.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit (b)(3) Peak Output Power Frequency Range (MHz) Result 1 watt or 30dBm PASS TEST PROCEDURE a. The EUT was directly connected to the Power meter DEVIATION FROM STANDARD No deviation TEST SETUP EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. EMC Report Tel: Web: Page 31 of 39

32 6.1.5 TEST RESULTS Temperature: 25 Relative Humidity: 60% Pressure: 1012 hpa Test Voltage : DC 3.0V Test Mode : TX Mode Test Channe TX Mode Maximum Conducted Output Frequency Power(PK) LIMIT (MHz) (dbm) dbm CH CH CH EMC Report Tel: Web: Page 32 of 39

33 7. BAND EDGE APPLICABLE STANDARD In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in (a), must also comply with the radiated emission limits specified in (a) (see (c)). TEST PROCEDURE a) Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. b) Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. c) Set RBW to 100 khz and VBW of spectrum analyzer to 300 khz with a convenient frequency span including 100 khz bandwidth from band edge. d) Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. e) Repeat above procedures until all measured frequencies were complete. EMC Report Tel: Web: Page 33 of 39

34 7.1 DEVIATION FROM STANDARD No deviation. 7.2 TEST SETUP 7.3 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. EMC Report Tel: Web: Page 34 of 39

35 7.4 TEST RESULTS Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC-LH E Temperature: 25 Relative Humidity: 60% Pressure: 1012 hpa Test Voltage : DC 3.0V Band Edge, Left Side Band Edge, Right Side EMC Report Tel: Web: Page 35 of 39

36 8. ANTENNA REQUIREMENT 8.1 STANDARD REQUIREMENT requirement: For intentional device, according to : an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 8.2 EUT ANTENNA The EUT antenna is PCB antenna,. It comply with the standard requirement. EMC Report Tel: Web: Page 36 of 39

37 9. TEST SEUUP PHOTO Radiated Emission Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC-LH E EMC Report Tel: Web: Page 37 of 39

38 EMC Report Tel: Web: Page 38 of 39

39 10. EUT PHOTO Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC-LH E END OF REPORT EMC Report Tel: Web: Page 39 of 39