FCC RADIO TEST REPORT-WIFI FCC ID:2AC6K-SP006

Transcription

1 FCC RADIO TEST REPORT-WIFI FCC ID:2AC6K-SP006 Product: IP Camera Trade Name: Sricam Model Name: SP006 SP004,SP009,SP010,SP011,SP012,SP013, SP014,SP015,SP016,SP017, SP018, SP019, Serial Model: SP020,NVS001,NVS002,DB001,DB002,DB003, SM001, SM002. Report No.: NTEK-2015NT F Prepared for Shenzhen Sricctv Technology Co., Ltd. The 2nd Floor, 9th Building, Fu Zhong Industrial Park,Fuyong Street, Bao an,,shenzhen, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao an District, Shenzhen P.R. China Tel.: Fax.: Website:

2 Page 2 of 57 Report No.: NTEK-2015NT F TEST RESULT CERTIFICATION Applicant s name... Shenzhen Sricctv Technology Co., Ltd. Address... The 2nd Floor, 9th Building, Fu Zhong Industrial Park,Fuyong Street, Bao an,,shenzhen, China Manufacture's Name... Shenzhen Sricctv Technology Co., Ltd. Address... The 2nd Floor, 9th Building, Fu Zhong Industrial Park,Fuyong Street, Bao an,,shenzhen, China Product description Product name...ip Camera Model and/or type reference... SP006 Serial Model... SP004,SP009,SP010,SP011,SP012,SP013, SP014,SP015,SP016,SP017, SP018, SP019, SP020,NVS001,NVS002,DB001,DB002,DB003, SM001, SM002 Standards... FCC Part Oct Test procedure...ansi C and KDB : June 5, 2014 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test... Date (s) of performance of tests Jun ~16 Jul Date of Issue Jul Test Result... Pass Testing Engineer : Denny Huang Technical Manager : (Brown Lu) Authorized Signatory : (Sam Chen)

3 Page 3 of 57 Report No.: NTEK-2015NT F Table of Contents Page 1. SUMMARY OF TEST RESULTS TEST FACILITY MEASUREMENT UNCERTAINTY 6 2. GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) EQUIPMENTS LIST FOR ALL TEST ITEMS EMC EMISSION TEST CONDUCTED EMISSION MEASUREMENT POWER LINE CONDUCTED EMISSION LIMITS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS RADIATED EMISSION MEASUREMENT RADIATED EMISSION LIMITS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS (BETWEEN 9KHZ 30 MHZ) TEST RESULTS (BETWEEN 30MHZ 1GHZ) TEST RESULTS (ABOVE 1000 MHZ) POWER SPECTRAL DENSITY TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS BANDWIDTH TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE 37

4 Page 4 of 57 Report No.: NTEK-2015NT F Table of Contents Page TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS PEAK OUTPUT POWER TEST APPLIED PROCEDURES / LIMIT TEST PROCEDURE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS KHZ BANDWIDTH OF FREQUENCY BAND EDGE DEVIATION FROM STANDARD TEST SETUP EUT OPERATION CONDITIONS TEST RESULTS ANTENNA REQUIREMENT STANDARD REQUIREMENT EUT ANTENNA EUT TEST PHOTO 56 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS

5 Page 5 of 57 Report No.: NTEK-2015NT F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: Standard Section FCC Part15 (15.247), Subpart C Test Item Judgment Remark Conducted Emission PASS (a)(2) 6dB Bandwidth PASS (b) Peak Output Power PASS (c) Radiated Spurious Emission PASS (d) Power Spectral Density PASS Band Edge Emission PASS Antenna Requirement PASS NOTE: (1) N/A denotes test is not applicable in this Test Report

6 Page 6 of 57 Report No.: NTEK-2015NT F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add.:1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U,where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of approximately 95 % No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1g) ±4.68dB 5 All emissions,radiated(>1g) ±4.89dB 6 Temperature ±0.5 C 7 Humidity ±2%

7 Page 7 of 57 Report No.: NTEK-2015NT F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Trade Name Model Name Serial Model Model Difference IP Camera Sricam SP006 SP004,SP009,SP010,SP011,SP012,SP013, SP014,SP015,SP016,SP017, SP018, SP019, SP020,NVS001,NVS002,DB001,DB002,DB003, SM001, SM002 All the model are the same circuit and RF module, except the model name and colour. Product Description Operation Frequency: b/g/n(20MHz): 2412~2462MHz n(40MHz):2422~2452MHz Modulation Type: IEEE b : DSSS (CCK, QPSK, DBPSK) IEEE g/n (HT20/HT40) : OFDM (64QAM, 16QAM, QPSK, BPSK) Bit Rate of Transmitter Number Of Channel Antenna Designation: Antenna Gain (dbi) b:11/5.5/2/1 Mbps g:54/48/36/24/18/12/9/6Mbps n(20MHz/40MHz):150/144.44/1 30/117/115.56/104/86.67/78/52/6.5Mb ps b/g/n20MHz:11CH n40MHz:7CH Please see Note dbi Channel List Please refer to the Note 2. Ratings Adapter Battery Connecting I/O Port(s) DC 5V Form Adapter AC 120V/60Hz Mode: Sr-608 Input: V~, 50/60Hz Output: 5.0V, 2000mA N/A Please refer to the User's Manual

8 Page 8 of 57 Report No.: NTEK-2015NT F Note: 1. For a more detailed features description, please refer to the manufacturer s specifications or the User's Manual. 2. Channel List for b/g/n(20 MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel List for n(40MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 3. Table for Filed Antenna Ant Brand Model Name Antenna Type Connector Gain (dbi) NOTE. Wifi A N/A N/A External Antenna N/A 2.0 Antenna

9 Page 9 of 57 Report No.: NTEK-2015NT F 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Description b CH1/ CH6/ CH g CH1/ CH6/ CH n20 CH1/ CH6/ CH n40 CH3/ CH6/ CH9 Link Mode For Conducted Emission Final Test Mode Mode 5 Description Link Mode Final Test Mode Mode 1 Mode 2 Mode 3 For Radiated Emission Description b CH1/ CH6/ CH g CH1/ CH6/ CH n20 CH1/ CH6/ CH11 Mode n40 CH3/ CH6/ CH 9 Mode 5 Link Mode Note: (1) The measurements are performed at the highest, middle, lowest available channels. (2) The measurements are performed at all Bit Rate of Transmitter, the worst data was reported (3) EUT configured to transmit continuously: Operated Mode for Worst Duty Cycle Test Signal Duty Cycle (x) 100% - IEEE b 100% - IEEE g 100% - IEEE n (HT20) 100% - IEEE n (HT40) Average correction factor (db)

10 Page 10 of 57 Report No.: NTEK-2015NT F 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED E-1 EUT C-1 E-2 Adapter AC Plug

11 Page 11 of 57 Report No.: NTEK-2015NT F 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Brand Model/Type No. Series No. Note E-1 IP Camera Sricam SP006 N/A EUT E-2 Adapter N/A Sr-608 N/A Item Shielded Type Ferrite Core Length Note C-1 NO NO 1.2m Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in Length column.

12 Page 12 of 57 Report No.: NTEK-2015NT F 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Item Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Calibratio n period 1 Spectrum MY Agilent E4407B Analyzer year 1* Spectrum MY Agilent E4407B Analyzer year 2 Test Receiver R&S ESPI year 3 Bilog Antenna TESEQ CBL6111D year 3* Bilog Antenna TESEQ CBL6111D year 50Ω Coaxial Anritsu MP59B year Switch 6 Spectrum 5 ADVANTEST R year Analyzer EM-AH Horn Antenna EM year 80 EM-AH-101 6* Horn Antenna EM year 80 7 Horn Ant Schwarzbeck BBHA year 7* Horn Ant Schwarzbeck BBHA year 8 Amplifier EM EM year 9 Loop Antenna ARA PLA-1030/B year 10 Power Meter R&S NRVS year 10* Power Meter R&S NRVS year 11 Power R&S URV5-Z4 Sensor year 11* Power R&S URV5-Z4 Sensor year 12 Test Cable N/A R-01 N/A year 12* Test Cable N/A R-01 N/A year 13 Test Cable N/A R-02 N/A year 13* Test Cable N/A R-02 N/A year

13 Page 13 of 57 Report No.: NTEK-2015NT F Conduction Test equipment Item Kind of Equipment Manufactu rer Type No. Serial No. Last calibration Calibrated until Calibratio n period 1 Test Receiver R&S ESCI year 2 LISN R&S ENV year 3 LISN EMCO 3816/ year 50Ω Coaxial Anritsu MP59B year Switch 7 5 Passive Voltage R&S ESH2-Z year Probe 6 Absorbing clamp R&S MOS year 7 Test Cable N/A C01 N/A year 8 Test Cable N/A C02 N/A year 9 Test Cable N/A C03 N/A year 1 Attenuation MCE BN year

14 Page 14 of 57 Report No.: NTEK-2015NT F 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT POWER LINE CONDUCTED EMISSION Limits (Frequency Range 150KHz-30MHz) FREQUENCY (MHz) Class A (dbuv) Class B (dbuv) Quasi-peak Average Quasi-peak Average Standard * * CISPR CISPR CISPR * * FCC FCC FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Attenuation Start Frequency Stop Frequency IF Bandwidth Setting 10 db 0.15 MHz 30 MHz 9 khz

15 Page 15 of 57 Report No.: NTEK-2015NT F TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item EUT Test Photos DEVIATION FROM TEST STANDARD No deviation TEST SETUP Vertical R eference Ground Plane Test Receiver 40cm EUT LISN 80cm Horizontal Reference Ground P lane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AM N) are 80 cm from EUT and at least 80 from other units and other m etal planes EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

16 Page 16 of 57 Report No.: NTEK-2015NT F TEST RESULTS EUT: IP Camera Model Name. : SP006 Temperature: 26 Relative Humidity: 56% Pressure: 1010hPa Phase : L Test Voltage : DC 5V From adapter AC120V/60Hz Test Mode: Mode 5 Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbμv) (db) (dbμv) (dbμv) (db) Remark QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

17 Page 17 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name. : SP006 Temperature: 26 Relative Humidity: 56% Pressure: 1010hPa Phase : N Test Voltage : DC 5V From adapter AC120V/60Hz Test Mode: Mode 5 Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbμv) (db) (dbμv) (dbμv) (db) Remark QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

18 Page 18 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name. : SP006 Temperature: 26 Relative Humidity: 56% Pressure: 1010hPa Phase : L Test Voltage : DC 5V form Adapter AC 240V/60Hz Test Mode: Mode 5 Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbμv) (db) (dbμv) (dbμv) (db) Remark QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

19 Page 19 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name. : SP006 Temperature: 26 Relative Humidity: 56% Pressure: 1010hPa Phase : N Test Voltage : DC 5V form Adapter AC 240V/60Hz Test Mode: Mode 5 Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbμv) (db) (dbμv) (dbμv) (db) Remark QP AVG QP AVG QP AVG QP AVG QP AVG QP AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

20 Page 20 of 57 Report No.: NTEK-2015NT F 3.2 RADIATED EMISSION MEASUREMENT RADIATED EMISSION LIMITS (Frequency Range 9kHz-1000MHz) 20dBc in any 100 khz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on (a), then the (a) limit in the table below has to be followed. Frequencies (MHz) Field Strength (micorvolts/meter) Measurement Distance (meters) 0.009~ /F(KHz) ~ /F(KHz) ~ ~ ~ ~ Above LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) FREQUENCY (MHz) PEAK dbuv/m@at 3M AVERAGE Above Notes: (1) The limit for radiated test was performed according to FCC PART 15C. (2) The tighter limit applies at the band edges. (3) Emission level (dbuv/m)=20log Emission level (uv/m). Spectrum Parameter Attenuation Start Frequency Stop Frequency RB / VB (emission in restricted band) Setting Auto 1000 MHz 10th carrier harmonic 1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for Average Receiver Parameter Attenuation Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Setting Auto 9kHz~150kHz / RB 200Hz for QP 150kHz~30MHz / RB 9kHz for QP 30MHz~1000MHz / RB 120kHz for QP

21 Page 21 of 57 Report No.: NTEK-2015NT F TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 m for below 1GHz and 1.5m for above 1GHz the ground at a 3 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. c. The height of the equipment or of the substitution antenna shall be 0.8 m for below 1GHz and 1.5m for above 1GHz; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported During the radiated emission test, the Spectrum Analyzer was set with the following configurations: Frequency Band (MHz) Function Resolution bandwidth Video Bandwidth 30 to 1000 Peak 100 khz 100 khz Above 1000 Peak 1 MHz 1 MHz Average 1 MHz 10 Hz DEVIATION FROM TEST STANDARD No deviation

22 Page 22 of 57 Report No.: NTEK-2015NT F TEST SETUP (A)Radiated Emission Test-Up Frequency Below 30MHz (B)Radiated Emission Test-Up Frequency 30MHz~1GHz

23 Page 23 of 57 Report No.: NTEK-2015NT F (C)Radiated Emission Test-Up Frequency Above 1GHz EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.

24 Page 24 of 57 Report No.: NTEK-2015NT F TEST RESULTS (BETWEEN 9KHZ 30 MHZ) EUT: IP Camera Model Name. : SP006 Temperature: 20 Relative Humidtity: 48% Pressure: 1010 hpa Test Voltage : DC 5V form Adapter AC 120V/60Hz Test Mode : TX Polarization : -- Freq. Reading Limit Margin State (MHz) (dbuv/m) (dbuv/m) (db) P/F N/A N/A NOTE: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(db); Limit line = specific limits(dbuv) + distance extrapolation factor.

25 Page 25 of 57 Report No.: NTEK-2015NT F TEST RESULTS (BETWEEN 30MHZ 1GHZ) EUT: IP Camera Model Name : SP006 Temperature: 20 Relative Humidity: 48% Pressure: 1010 hpa Test Voltage : DC 5V form Adapter AC 120V/60Hz Test Mode : TX Polar (H/V) Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbuv) (db) (dbuv/m) (dbuv/m) (db) Remark V QP V QP V QP V QP V QP V QP Remark: Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level - Limit

26 Page 26 of 57 Report No.: NTEK-2015NT F Polar (H/V) Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbuv) (db) (dbuv/m) (dbuv/m) (db) Remark H QP H QP H QP H QP H QP H QP Remark: Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level - Limit

27 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) Page 27 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 20 Relative Humidity: 48% Pressure: 1010 hpa Test Voltage : DC 5V form Adapter AC 120V/60Hz Test Mode : TX Polar (H/V) Frequency Meter Reading Factor Emission Level Limits Margin (MHz) (dbuv) (db) (dbuv/m) (dbuv/m) (db) Detector Type Low Channel (2412 MHz)-Above 1G Vertical Pk Vertical Av Vertical Pk Vertical Av Horizontal Pk Horizontal Av Horizontal Pk Horizontal Av Mid Channel (2437 MHz)-Above 1G Vertical Pk Vertical Av Vertical Pk Vertical Av Horizontal Pk Horizontal Av Horizontal Pk Horizontal Av High Channel (2462 MHz)- Above 1G Vertical Pk Vertical Av Vertical Pk Vertical Av Horizontal Pk Horizontal Av Horizontal Pk Horizontal Av Note: b mode is the worst mode.

28 Page 28 of 57 Report No.: NTEK-2015NT F 4. POWER SPECTRAL DENSITY TEST 4.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit Power Spectral Density 8 dbm (in any 3KHz) Frequency Range (MHz) Result PASS TEST PROCEDURE 1. Set analyzer center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS channel bandwidth khz Set the RBW 100 khz. 4. Set the VBW 3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level within the RBW. 10. If measured value exceeds limit, reduce RBW (no less than 3 khz) and repeat DEVIATION FROM STANDARD No deviation TEST SETUP Att EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.1 Unless otherwise a special operating condition is specified in the follows during the testing.

29 Page 29 of 57 Report No.: NTEK-2015NT F TEST RESULTS EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1015 hpa Test Voltage : AC 120V/60Hz Test Mode : TX b Mode /CH01, CH06, CH11 Frequency Power Density (dbm) Limit (dbm) Result 2412 MHz PASS 2437 MHz PASS 2462 MHz PASS TX CH01

30 Page 30 of 57 Report No.: NTEK-2015NT F TX CH06 TX CH11

31 Page 31 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1015 hpa Test Voltage : AC 120V/60Hz Test Mode : TX g Mode /CH01, CH06, CH11 Frequency Power Density (dbm) Limit (dbm) Result 2412 MHz PASS 2437 MHz PASS 2462 MHz PASS TX CH01

32 Page 32 of 57 Report No.: NTEK-2015NT F TX CH06 TX CH11

33 Page 33 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1015 hpa Test Voltage : AC 120V/60Hz Test Mode : TX n Mode (20MHz)/CH01, CH06, CH11 Frequency Power Density (dbm) Limit (dbm) Result 2412 MHz PASS 2437 MHz PASS 2462 MHz PASS TX CH01

34 Page 34 of 57 Report No.: NTEK-2015NT F TX CH06 TX CH11

35 Page 35 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1015 hpa Test Voltage : AC 120V/60Hz Test Mode : TX n Mode (40MHz)/CH03, CH06, CH09 Frequency Power Density (dbm) Limit (dbm) Result 2422 MHz PASS 2437 MHz PASS 2452 MHz PASS TX CH03

36 Page 36 of 57 Report No.: NTEK-2015NT F TX CH06 TX CH09

37 Page 37 of 57 Report No.: NTEK-2015NT F 5. BANDWIDTH TEST 5.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit Frequency Range (MHz) Result (a)(2) Bandwidth >= 500KHz (6dB bandwidth) PASS TEST PROCEDURE 1. Set RBW = 100 khz. 2. Set the video bandwidth (VBW) 3 x RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower) that are attenuated by 6 db relative to the maximum level measured in the fundamental emission. TEST SETUP EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.

38 Page 38 of 57 Report No.: NTEK-2015NT F TEST RESULTS EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1012 hpa Test Voltage : AC 120V/60Hz Test Mode : TX b Mode /CH01, CH06, CH11 Channel Frequency (MHz) 6dB bandwidth (MHz) Limit (khz) Result Low Pass Middle Pass High Pass TX CH 01

39 Page 39 of 57 Report No.: NTEK-2015NT F TX CH 06 TX CH 11

40 Page 40 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 60% DC 5V form Adapter Pressure: 1012 hpa Test Voltage : AC 120V/60Hz Test Mode : TX g Mode /CH01, CH06, CH11 Channel Frequency (MHz) 6dB bandwidth (MHz) Limit (khz) Result Low Pass Middle Pass High Pass TX CH 01

41 Page 41 of 57 Report No.: NTEK-2015NT F TX CH 06 TX CH 11

42 Page 42 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1012 hpa Test Voltage : AC 120V/60Hz Test Mode : TX n Mode(20M) /CH01, CH06, CH11 Channel Frequency (MHz) 6dB bandwidth (MHz) Limit (khz) Result Low Pass Middle Pass High Pass TX CH 01

43 Page 43 of 57 Report No.: NTEK-2015NT F TX CH 06 TX CH 11

44 Page 44 of 57 Report No.: NTEK-2015NT F EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1012 hpa Test Voltage : AC 120V/60Hz Test Mode : TX n Mode(40M) /CH03, CH06, CH09 Channel Frequency (MHz) 6dB bandwidth (MHz) Limit (khz) Result Low Pass Middle Pass High Pass TX CH 03

45 Page 45 of 57 Report No.: NTEK-2015NT F TX CH 06 TX CH 09

46 Page 46 of 57 Report No.: NTEK-2015NT F 6. PEAK OUTPUT POWER TEST 6.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247), Subpart C Section Test Item Limit (b)(3) Peak Output Power Frequency Range (MHz) Result 1 watt or 30dBm PASS TEST PROCEDURE a. The EUT was directly connected to the Power meter DEVIATION FROM STANDARD No deviation TEST SETUP Att EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.

47 Page 47 of 57 Report No.: NTEK-2015NT F TEST RESULTS EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 60% Pressure: 1012 hpa Test Voltage : DC 5V form Adapter AC 120V/60Hz Test Mode : TX b/g/n(20m/40m) Mode Test Channe Frequency TX b Mode Maximum Peak Maximum Peak Conducted Output Conducted Output Power(PK) Power(AV) LIMIT (MHz) (dbm) (dbm) dbm CH CH CH TX g Mode CH CH CH TX n(20) Mode CH CH CH TX n(40) Mode CH CH CH

48 Page 48 of 57 Report No.: NTEK-2015NT F KHZ BANDWIDTH OF FREQUENCY BAND EDGE APPLICABLE STANDARD In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in (a), must also comply with the radiated emission limits specified in (a) (see (c)). TEST PROCEDURE a) Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. b) Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. c) Set RBW to 100 khz and VBW of spectrum analyzer to 300 khz with a convenient frequency span including 100 khz bandwidth from band edge. d) Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. e) Repeat above procedures until all measured frequencies were complete. 7.1 DEVIATION FROM STANDARD No deviation. 7.2 TEST SETUP Att 7.3 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.

49 Page 49 of 57 Report No.: NTEK-2015NT F 7.4 TEST RESULTS EUT: IP Camera Model Name : SP006 Temperature: 25 Relative Humidity: 56% DC 5V form Adapter Pressure: 1012 hpa Test Voltage : AC 120V/60Hz Frequency Band MHz Delta Peak to band emission (dbc) >Limit (dbc) Result b mode g mode n-HT20 mode n-HT40 mode Pass 20 Pass 20 Pass 20 Pass 20 Pass 20 Pass 20 Pass 20 Pass

50 Page 50 of 57 Report No.: NTEK-2015NT F Radiated band edge: Frequency Meter Reading Factor Emission Level Limits Margin Detector (MHz) (dbμv) (db) (dbμv/m) (dbμv/m) (db) Type b Comment peak Vertical peak Horizontal peak Vertical peak Horizontal g peak Vertical peak Horizontal peak Vertical peak Horizontal n(20) peak Vertical peak Horizontal peak Vertical peak Horizontal n(40) peak Vertical peak Horizontal peak Vertical peak Horizontal Note: Test method to see chapter 3.2. When PK value is lower than the Average value limit, average not record.

51 Page 51 of 57 Report No.: NTEK-2015NT F b: Band Edge, Right Side b: Band Edge, Left Side

52 Page 52 of 57 Report No.: NTEK-2015NT F g: Band Edge, Right Side g: Band Edge, Left Side

53 Page 53 of 57 Report No.: NTEK-2015NT F n-HT20: Band Edge, Right Side n-HT20: Band Edge, Left Side

54 Page 54 of 57 Report No.: NTEK-2015NT F n-HT40: Band Edge, Right Side n-HT40: Band Edge, Left Side

55 Page 55 of 57 Report No.: NTEK-2015NT F 8. ANTENNA REQUIREMENT 8.1 STANDARD REQUIREMENT requirement: For intentional device, according to : an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 8.2 EUT ANTENNA The EUT antenna is unique connector antenna(r-sma), detailed in the External photos, It comply with the standard requirement.

56 Page 56 of 57 Report No.: NTEK-2015NT F 9. EUT TEST PHOTO Radiated Measurement Photos

57 Page 57 of 57 Report No.: NTEK-2015NT F CONDUCTED EMISSION Photos