TEST REPORT. Reference No... : WTS17S E V1 FCC ID... : 2AC7IEKOOQ60. Applicant... : Interglobe Connection Corp

Transcription

1 TEST REPORT Reference No.... : WTS17S E V1 FCC ID... : 2AC7IEKOOQ60 Applicant... : Interglobe Connection Corp Address... : 8228 NW 30th Terrace, Doral, Florida, United States Manufacturer... : The same as above Address... : The same as above Product... : Smart Phone Model(s).... : Omega LTE Q60 Brand Name... : EKO Standards... : FCC CFR47 Part : 2016 Date of Receipt sample... : Date of Test... : to Date of Issue... : Test Result... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel : Fax: Compiled by: Approved by: Ford Wang / Project Engineer Philo Zhong / Manager Page 1 of 91

2 Reference No.: WTS17S E V1 Page 2 of 91 2 Laboratories Introduction Waltek Services Test Group Ltd. is one of the largest and the most comprehensive third party testing organizations in China, our headquarter located in Shenzhen (CNAS Registration No. L3110, A2LA Certificate Number: ) and have branches in Foshan (CNAS Registration No. L6478), Dongguan (CNAS Registration No. L9950), Zhongshan, Suzhou (CNAS Registration No. L7754), Ningbo and Hong Kong, Our test capability covered four large fields: safety test. Electronic Magnetic Compatibility(EMC), reliability and energy performance, Chemical test. Meanwhile, Waltek has got recognition as registration and accreditation laboratory from EMSD (Electrical and Mechanical Services Department), and American Energy star, FCC(The Federal Communications Commission), CPSC(Consumer Product Safety Commission), CEC(California energy efficiency), IC(Industry Canada) and ELI(Efficient Lighting Initiative). It s the strategic partner and data recognition laboratory of international authoritative organizations, such as UL, Intertek(ETL- SEMKO), CSA, TÜV Rheinland, TÜV SÜD, etc. As a professional, comprehensive, justice international test organization, we still keep the scientific and rigorous work attitude to help each client satisfy the international standards and assist their product enter into globe market smoothly. Waltek Services (Shenzhen) Co., Ltd. A. Accreditations for Conformity Assessment (International) Country/Region Accreditation Body Scope Note USA FCC ID \ DOC \ VOC 1 Canada IC ID \ VOC 2 CNAS Japan MIC-T \ MIC-R - (Registration No.: L3110) Europe EMCD \ RED - A2LA Taiwan NCC - (Certificate No.: ) Hong Kong OFCA - Australia RCM - India WPC - Thailand International Services NTC - Singapore IDA - Note: 1. FCC Designation No.: CN1201. Test Firm Registration No.: IC Canada Registration No.: 7760A B. TCBs and Notify Bodies Recognized Testing Laboratory. Recognized Testing Laboratory of Notify body number

3 Reference No.: WTS17S E V1 Page 3 of 91 TUV Rheinland Intertek Optional. TUV SUD SGS Phoenix Testlab GmbH 0700 Element Materials Technology Warwick Ltd 0891 Timco Engineering, Inc Eurofins Product Service GmbH 0681

4 Reference No.: WTS17S E V1 Page 4 of 91 3 Contents Page 1 COVER PAGE LABORATORIES INTRODUCTION CONTENTS REVISION HISTORY GENERAL INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T CHANNEL LIST TEST MODE TEST SUMMARY EQUIPMENT USED DURING TEST EQUIPMENTS LIST DESCRIPTION OF SUPPORT UNITS MEASUREMENT UNCERTAINTY TEST EQUIPMENT CALIBRATION CONDUCTED EMISSION E.U.T. OPERATION EUT SETUP MEASUREMENT DESCRIPTION CONDUCTED EMISSION TEST RESULT RADIATED EMISSIONS EUT OPERATION TEST SETUP SPECTRUM ANALYZER SETUP TEST PROCEDURE CORRECTED AMPLITUDE & MARGIN CALCULATION SUMMARY OF TEST RESULTS CONDUCTED SPURIOUS EMISSIONS TEST PROCEDURE TEST RESULT BAND EDGE MEASUREMENT TEST PRODUCE TEST RESULT DB BANDWIDTH MEASUREMENT TEST PROCEDURE: TEST RESULT: MAXIMUM PEAK OUTPUT POWER TEST PROCEDURE: TEST RESULT: POWER SPECTRAL DENSITY TEST PROCEDURE: TEST RESULT: ANTENNA REQUIREMENT RF EXPOSURE PHOTOGRAPHS OF TEST SETUP AND EUT

5 Reference No.: WTS17S E V1 Page 5 of 91 4 Revision History Test report No. Date of Receipt sample Date of Test Date of Issue Purpose Comment Approved WTS17S E to original - Replaced WTS17S E V to Version 1 Updated Valid

6 Reference No.: WTS17S E V1 Page 6 of 91 5 General Information 5.1 General Description of E.U.T. Product: Smart Phone Model(s): Omega LTE Q60 Model Description: N/A GSM Band(s): GSM 850/900/1800/1900MHz GPRS/EGPRS Class: 12 WCDMA Band(s): FDD Band II/IV/V LTE Band(s): FDD Band 4/7 Wi-Fi Specification: 2.4G b/g/n HT20/n HT40 Bluetooth Version: Bluetooth v4.0 with BLE GPS: Support NFC: N/A Hardware Version: D6S_03_C00SEA Software Version: Highest frequency (Exclude Radio): Storage Location: Note: EKO OMEGA LTE Q60_CA_V G Internal Storage N/A 5.2 Details of E.U.T. Operation Frequency: Max. RF output power: GSM/GPRS/EDGE 850: 824~849MHz PCS/GPRS/EDGE 1900: 1850~1910MHz WCDMA Band II: 1850~1910MHz WCDMA Band V: 824~849MHz WCDMA Band IV:1710~1755MHz LTE Band 4: 1710~1755MHz LTE Band 7: MHz WiFi: b/g/n HT20: 2412~2462MHz n HT40: 2422~2452MHz Bluetooth: 2402~2480MHz GSM 850: 32.71dBm PCS1900: 29.82dBm WCDMA Band II: 22.88dBm WCDMA Band V: 22.55dBm WCDMA Band IV: 22.68dBm LTE Band 4: 21.87dBm LTE Band 7: 21.92dBm

7 Reference No.: WTS17S E V1 Page 7 of 91 Type of Modulation: Antenna installation: Antenna Gain: Ratings: Adapter: WiFi(2.4G): 9.43dBm Bluetooth: 3.06dBm GSM,GPRS: GMSK EDGE: GMSK, 8PSK WCDMA: BPSK, 16QAM LTE: QPSK, 16QAM WiFi: CCK, OFDM Bluetooth: GFSK, Pi/4 DQPSK, 8DPSK GSM/WCDMA/LTE: internal permanent antenna WiFi/Bluetooth: internal permanent antenna GSM 850: -3.5dBi PCS1900: -1.0dBi WCDMA Band II: -1.0dBi WCDMA Band V: -3.5dBi CDMA Band IV: -1.2dBi LTE Band 4: -1.2dBi LTE Band 7: 1.5dBi WiFi(2.4G): 2.0dBi Bluetooth: 2.0dBi Battery DC 3.8V, 2900mAh DC 5V, 1.0A, charging from adapter (Adapter Input: V~50/60Hz 0.15A) Manufacture: Shenzhen GuangYuanSheng Technology Co.,Ltd. Model No.:

8 Reference No.: WTS17S E V1 Page 8 of Channel List WIFI Channel No. Frequency (MHz) Channel No. Frequency (MHz) Channel No. Frequency (MHz) Channel No. Frequency (MHz) BT BLE Channel No. Frequency (MHz) Channel No. Frequency (MHz) Channel No. Frequency (MHz) Channel No. Frequency (MHz)

9 Reference No.: WTS17S E V1 Page 9 of Test Mode Table 1 Tests Carried Out Under FCC part Test Items Mode Data Rate Channel TX/RX b 1 Mbps 1/6/11 TX Maximum Peak Output Power g 6 Mbps 1/6/11 TX n HT20 MCS0 1/6/11 TX n HT40 MCS0 3/6/9 TX b 1 Mbps 1/6/11 TX Power Spectral Density g 6 Mbps 1/6/11 TX n HT20 MCS0 1/6/11 TX n HT40 MCS0 3/6/9 TX b 1 Mbps 1/6/11 TX 6dB Bandwidth g 6 Mbps 1/6/11 TX n HT20 MCS0 1/6/11 TX n HT40 MCS0 3/6/9 TX b 1 Mbps 1/6/11 TX Band Edge g 6 Mbps 1/6/11 TX n HT20 MCS0 1/6/11 TX n HT40 MCS0 3/6/9 TX b 1 Mbps 1/6/11 TX Transmitter Spurious Emissions g 6 Mbps 1/6/11 TX n HT20 MCS0 1/6/11 TX n HT40 MCS0 3/6/9 TX Table 2 Tests Carried Out Under FCC part Test Items Mode Data Rate Channel TX/RX Maximum Peak Output Power BT BLE 1 Mbps 0/19/39 TX Power Spectral Density BT BLE 1 Mbps 0/19/39 TX 6dB Bandwidth BT BLE 1 Mbps 0/19/39 TX Band Edge BT BLE 1 Mbps 0/19/39 TX Transmitter Spurious Emissions BT BLE 1 Mbps 0/19/39 TX Note :Parameters set by test software during channel & power tests, the software provided by the customer was used to set the operating channels as well as the output power level. The RF output power set is the power expected by the manufacturer and is going to be fixed on the firmware of the final product.

10 Reference No.: WTS17S E V1 Page 10 of 91 6 Test Summary Test Items Test Requirement Result Radiated Spurious Emissions (d) (a) (a) PASS Conducted Spurious Emissions (d) PASS Conducted Emissions (a) PASS 6dB Bandwidth (a)(2) PASS Maximum Peak Output Power (b)(3),(4) PASS Power Spectral Density (e) PASS Band Edge (d) PASS Antenna Requirement PASS Maximum Permissible Exposure (Exposure of Humans to RF Fields) (b)(1) PASS

11 Reference No.: WTS17S E V1 Page 11 of 91 7 Equipment Used during Test 7.1 Equipments List Conducted Emissions Test Site 1# Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. EMI Test Receiver R&S ESCI LISN R&S ENV Cable Top TYPE16(3.5M) Conducted Emissions Test Site 2# Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. EMI Test Receiver R&S ESCI LISN SCHWARZBECK NSLK Limiter York MTS-IMP Cable LARGE RF m Semi-anechoic Chamber for Radiation Emissions Test site 1# Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 Spectrum Analyzer R&S FSP Active Loop Antenna Beijing Dazhi ZN30900A Trilog Broadband Antenna SCHWARZBECK VULB Coaxial Cable (below 1GHz) Top TYPE16(13M) Broad-band Horn Antenna SCHWARZBECK BBHA 9120 D Broad-band Horn Antenna SCHWARZBECK BBHA Broadband COMPLIANCE Preamplifier DIRECTION PAP-1G Coaxial Cable (above 1GHz) Top 1GHz-25GHz EW m Semi-anechoic Chamber for Radiation Emissions Test site 2# Item Equipment Manufacturer Model No. Serial No Last Calibration Date Calibration Due Date 1 Test Receiver R&S ESCI Trilog Broadband Antenna SCHWARZBECK VULB Amplifier Compliance pirection PAP systems inc 4 Cable HUBER+SUHNER CBL

12 Reference No.: WTS17S E V1 Page 12 of 91 RF Conducted Testing Item Equipment Manufacturer Model No. Serial No EMC Analyzer (9k~26.5GHz) Spectrum Analyzer (9k-6GHz) Signal Analyzer (9k~26.5GHz) 7.2 Description of Support Units Last Calibration Date Calibration Due Date Agilent E7405A MY R&S FSL Agilent N9010A MY Equipment Manufacturer Model No. Series No. / / / / 7.3 Measurement Uncertainty Parameter Uncertainty Conducted Emission ± 3.64 db(ac mains 150KHz~30MHz) Radiated Spurious Emissions ± 5.08 db (Bilog antenna 30M~1000MHz) ± 5.47 db (Horn antenna 1000M~25000MHz) Radio Frequency ± 1 x 10-7 Hz RF Power ± 0.42 db RF Power Density ± 0.7dB Conducted Spurious Emissions ± 2.76 db (9kHz~26500MHz) Confidence interval:95%. Confidence factor:k=2 7.4 Test Equipment Calibration All the test equipments used are valid and calibrated by CEPREI Certification Body that address is No.110 Dongguan Zhuang RD. Guangzhou, P.R.China.

13 Reference No.: WTS17S E V1 Page 13 of 91 8 Conducted Emission Test Requirement: FCC CFR 47 Part 15 Section Test Method: ANSI C63.10:2013 Test Result: PASS Frequency Range: 150kHz to 30MHz Class/Severity: Class B Limit (dbμv) Limit: Frequency (MHz) Quasi-peak Average 0.15 to to 56* 56 to 46* 0.5 to to E.U.T. Operation Operating Environment : Temperature: Humidity: Atmospheric Pressure: 21.5 C 51.9 % RH 101.2kPa EUT Operation : The test was performed in TX transmitting mode, the worst data were shown in the report. 8.2 EUT Setup The conducted emission tests were performed using the setup accordance with the ANSI C m 0.8m EUT Receiver PC System 0.8m LISN :50 Terminator 8.3 Measurement Description The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within 6dB of the average limit line.

14 Reference No.: WTS17S E V1 Page 14 of Conducted Emission Test Result An initial pre-scan was performed on the live and neutral lines. Worst Mode: WIFI mode ( b mode low channel ) Live line:

15 Reference No.: WTS17S E V1 Page 15 of 91 Neutral line:

16 Reference No.: WTS17S E V1 Page 16 of 91 Worst Mode: BLE mode (low channel ) Live line:

17 Reference No.: WTS17S E V1 Page 17 of 91 Neutral line:

18 Reference No.: WTS17S E V1 Page 18 of 91 9 Radiated Emissions Test Requirement: FCC CFR47 Part 15 Section & Test Method: ANSI C63.10:2013 Test Result: PASS Measurement Distance: 3m Limit: Frequency Field Strength Field Strength Limit at 3m Measurement Dist (MHz) uv/m Distance (m) uv/m dbuv/m ~ /F(kHz) * 2400/F(kHz) 20log (2400/F(kHz)) ~ /F(kHz) * 24000/F(kHz) 20log (24000/F(kHz)) ~ * 30 20log (30) ~ log (100) 88 ~ log (150) 216 ~ log (200) Above log (500) 9.1 EUT Operation Operating Environment : Temperature: Humidity: Atmospheric Pressure: 23.5 C 52.1 % RH 101.2kPa EUT Operation : The test was performed in TX transmitting mode, the test data were shown in the report.

19 Reference No.: WTS17S E V1 Page 19 of Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the ANSI C The test setup for emission measurement below 30MHz. Semi-anechoic 3m Chamber Turn Table From 0 to 360 EUT 3m 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network The test setup for emission measurement from 30 MHz to 1 GHz. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network

20 Reference No.: WTS17S E V1 Page 20 of 91 The test setup for emission measurement above 1 GHz. Anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 EUT 3m bore sight antenna 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network 9.3 Spectrum Analyzer Setup Below 30MHz Sweep Speed... Auto IF Bandwidth... 10kHz Video Bandwidth... 10kHz Resolution Bandwidth... 10kHz 30MHz ~ 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth kHz Video Bandwidth kHz Above 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth... 1MHz Video Bandwidth... 3MHz Detector... Ave. Resolution Bandwidth... 1MHz Video Bandwidth... 10Hz

21 Reference No.: WTS17S E V1 Page 21 of Test Procedure 1. The EUT is placed on a turntable, which is 0.8m above ground plane for below 1GHz and 1.5m for above 1GHz. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The radiation measurements are performed in X,Y and Z axis positioning(x denotes lying on the table, Y denotes side stand and Z denotes vertical stand),the worst condition was tested putting the eut in Z axis,so the worst data were shown as follow. 8. A 2.4GHz high pass filter is used druing radiated emissions above 1GHz measurement. 9.5 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Antenna Factor + Cable Factor - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the maximum limit for Class B. The equation for margin calculation is as follows: Margin = Corr. Ampl. Limit

22 Reference No.: WTS17S E V1 Page 22 of Summary of Test Results Wifi: Test Frequency: 9KHz~30MHz Remark: only the worst data (802.11b/g/n Low channel mode) were recorded. Frequency Measurement results Detector PK/QP Correct factor db/m Extrapolatio n factor db Measurement results (calculated) Limits Margin db (MHz) Measurement results Detector Correct factor Extrapolatio n factor Measurement results (calculated) Limits Margin b QP QP QP g QP QP QP n(HT20) QP QP QP n(HT40) QP QP QP

23 Reference No.: WTS17S E V1 Page 23 of 91 Test Frequency : 30MHz ~ 18GHz Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11b: Low Channel 2412MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

24 Reference No.: WTS17S E V1 Page 24 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11b: Middle Channel 2437MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

25 Reference No.: WTS17S E V1 Page 25 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11b: High Channel 2462MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

26 Reference No.: WTS17S E V1 Page 26 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11g: Low Channel 2412MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

27 Reference No.: WTS17S E V1 Page 27 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11g: Middle Channel 2437MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

28 Reference No.: WTS17S E V1 Page 28 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11g: High Channel 2462MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

29 Reference No.: WTS17S E V1 Page 29 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n20: Low Channel 2412MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

30 Reference No.: WTS17S E V1 Page 30 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n20: Middle Channel 2437MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

31 Reference No.: WTS17S E V1 Page 31 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n20: High Channel 2462MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

32 Reference No.: WTS17S E V1 Page 32 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n40: Low Channel 2422MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

33 Reference No.: WTS17S E V1 Page 33 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n40: Middle Channel 2437MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

34 Reference No.: WTS17S E V1 Page 34 of 91 Frequency Receiver Reading Detector Turn table Angle FCC Part RX Antenna Corrected /209/205 Corrected Factor Height Polar Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) 11n40: High Channel 2452MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V Test Frequency: 18GHz~25GHz The measurements were more than 20 db below the limit and not reported.

35 Reference No.: WTS17S E V1 Page 35 of 91 BT BLE: Test Frequency: 9KHz~26MHz Remark: only the worst data (GFSK modulation Low channel mode) were recorded. Frequency Measurement results Detector PK/QP Correct factor db/m Extrapolatio n factor db Measurement results (calculated) Limits Margi n db (MHz) Measurement results Detector Correct factor Extrapolatio n factor Measurement results (calculated) Limits Margi n QP QP QP Test Frequency : 26MHz ~ 30MHz The measurements were more than 20 db below the limit and not reported. Test Frequency : 30MHz ~ 18GHz Frequency Receiver Reading Detector Turn table Angle RX Antenna Height Polar Corrected Factor Corrected Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) GFSK Low Channel 2402MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

36 Reference No.: WTS17S E V1 Page 36 of 91 Frequency Receiver Reading Detector Turn table Angle RX Antenna Height Polar Corrected Factor Corrected Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) GFSK Middle Channel 2440MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V

37 Reference No.: WTS17S E V1 Page 37 of 91 Frequency Receiver Reading Detector Turn table Angle RX Antenna Height Polar Corrected Factor Corrected Amplitude Limit Margin (MHz) (dbμv) (PK/QP/Ave) Degree (m) (H/V) (db) (dbμv/m) (dbμv/m) (db) GFSK High Channel 2480MHz QP H QP V PK V Ave V PK H Ave H PK V Ave V PK H Ave H PK V Ave V Test Frequency: 18GHz~25GHz The measurements were more than 20 db below the limit and not reported.

38 Reference No.: WTS17S E V1 Page 38 of Conducted Spurious Emissions Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r05 April 8, 2016 Test Result: PASS Limit: In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in Section (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section (a), must also comply with the radiated emission limits specified in Section (a) (see Section (c)) Test Procedure 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum; 2. Set the spectrum analyzer: Blow 30MHz: RBW = 100kHz, VBW = 300kHz, Sweep = auto Detector function = peak, Trace = max hold Above 30MHz: RBW =100kHz, VBW = 300kHz, Sweep = auto Detector function = peak, Trace = max hold

39 Reference No.: WTS17S E V1 Page 39 of Test Result 9KHz 30MHz b Low Channel Middle Channel

40 Reference No.: WTS17S E V1 Page 40 of 91 High Channel g Low Channel

41 Reference No.: WTS17S E V1 Page 41 of 91 Middle Channel High Channel

42 Reference No.: WTS17S E V1 Page 42 of n HT20 Low Channel Middle Channel

43 Reference No.: WTS17S E V1 Page 43 of 91 High Channel n HT40 Low Channel

44 Reference No.: WTS17S E V1 Page 44 of 91 Middle Channel High Channel

45 Reference No.: WTS17S E V1 Page 45 of 91 BLE Low Channel Middle Channel

46 Reference No.: WTS17S E V1 Page 46 of 91 High Channel

47 Reference No.: WTS17S E V1 Page 47 of 91 Above 30MHz b Low Channel Fundamental Middle Channel Fundamental

48 Reference No.: WTS17S E V1 Page 48 of 91 High Channel Fundamental g Low Channel Fundamental

49 Reference No.: WTS17S E V1 Page 49 of 91 Middle Channel Fundamental High Channel Fundamental

50 Reference No.: WTS17S E V1 Page 50 of n HT20 Low Channel Fundamental Middle Channel Fundamental

51 Reference No.: WTS17S E V1 Page 51 of 91 Fundamental High Channel n HT40 Low Channel Fundamental

52 Reference No.: WTS17S E V1 Page 52 of 91 Middle Channel Fundamental High Channel Fundamental

53 Reference No.: WTS17S E V1 Page 53 of 91 BLE Low Channel Fundamental Middle Channel Fundamental

54 Reference No.: WTS17S E V1 Page 54 of 91 High Channel Fundamental

55 Reference No.: WTS17S E V1 Page 55 of Band Edge Measurement Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r05 April 8, 2016 Test Limit: Regulation (d),in any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in (a), must also comply with the radiated emission limits specified in (a) (see (c)). Test Mode: Transmitting 11.1 Test Produce 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. 3. Set RBW to 100 khz and VBW of spectrum analyzer to 300 khz with a convenient frequency span including 100 khz bandwidth from band edge. 4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. 5. Repeat above procedures until all measured frequencies were complete.

56 Reference No.: WTS17S E V1 Page 56 of Test Result Test result plots shown as follows: TX 11b: Band edge-left side TX 11b: Band edge-right side

57 Reference No.: WTS17S E V1 Page 57 of 91 TX 11g: Band edge-left side TX 11g: Band edge-right side

58 Reference No.: WTS17S E V1 Page 58 of 91 TX 11n HT20: Band edge-left side TX 11n HT20: Band edge-right side

59 Reference No.: WTS17S E V1 Page 59 of 91 TX 11n HT40: Band edge-left side TX 11n HT40: Band edge-right side

60 Reference No.: WTS17S E V1 Page 60 of 91 BLE: Band edge-left side BLE: Band edge-right side

61 Reference No.: WTS17S E V1 Page 61 of db Bandwidth Measurement Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r05 April 8, Test Procedure: 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum; 2. Set the spectrum analyzer: RBW = 100kHz, VBW = 300kHz 12.2 Test Result: Operation mode Test Channel 6dB Bandwidth (MHz) 99% Bandwidth(MHz) Limit (khz) Channel TX 11b TX 11g TX 11n HT20 TX 11n HT40 BLE Channel Channel Channel Channel Channel Channel Channel Channel Channel Channel Channel Channel Channel Channel

62 Reference No.: WTS17S E V1 Page 62 of 91 Test result plot: Mode: TX 11b channel 1 Mode: TX 11b channel 6

63 Reference No.: WTS17S E V1 Page 63 of 91 Mode: TX 11b channel 11 Mode: TX 11g channel 1

64 Reference No.: WTS17S E V1 Page 64 of 91 Mode: TX 11g channel 6 Mode: TX 11g channel 11

65 Reference No.: WTS17S E V1 Page 65 of 91 Mode: TX 11n HT20 channel 1 Mode: TX 11n HT20 channel 6

66 Reference No.: WTS17S E V1 Page 66 of 91 Mode: TX 11n HT20 channel 11 Mode: TX 11n HT40 channel 3

67 Reference No.: WTS17S E V1 Page 67 of 91 Mode: TX 11n HT40 channel 6 Mode: TX 11n HT40 channel 9

68 Reference No.: WTS17S E V1 Page 68 of 91 BLE: channel 0 BLE: channel 19

69 Reference No.: WTS17S E V1 Page 69 of 91 BLE: channel 39

70 Reference No.: WTS17S E V1 Page 70 of Maximum Peak Output Power Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r05 April 8, Test Procedure: KDB D01 DTS Meas Guidance v03r05 April 8, 2016 section (For BLE) This procedure shall be used when the measurement instrument has available a resolution bandwidth that is greater than the DTS bandwidth. a)set the RBW DTS bandwidth. b)set VBW 3 RBW. c)set span 3 x RBW d)sweep time = auto couple. e)detector = peak. f)trace mode = max hold. g)allow trace to fully stabilize. h)use peak marker function to determine the peak amplitude level. section (For WIFI) This procedure may be used when the maximum available RBW of the measurement instrument is less than the DTS bandwidth. a)set the RBW = 1 MHz. b)set the VBW 3 RBW c)set the span 1.5 x DTS bandwidth. d)detector = peak. e)sweep time = auto couple. f)trace mode = max hold. g)allow trace to fully stabilize. h)use the instrument s band/channel power measurement function with the band limits set equal to the DTS bandwidth edges (for some instruments, this may require a manual override to select peak detector). If the instrument does not have a band power function, sum the spectrum levels (in linear power units) at intervals equal to the RBW extending across the DTS bandwidth.

71 Reference No.: WTS17S E V1 Page 71 of Test Result: Operation mode TX 11b TX 11g TX 11n HT20 TX 11n HT40 BLE Channel Frequency Maximum Peak Output (MHz) Power (dbm) Limit Low W/30dBm Middle W/30dBm High W/30dBm Low W/30dBm Middle W/30dBm High W/30dBm Low W/30dBm Middle W/30dBm High W/30dBm Low W/30dBm Middle W/30dBm High W/30dBm Low W/30dBm Middle W/30dBm High W/30dBm

72 Reference No.: WTS17S E V1 Page 72 of 91 Test Plot Mode: TX 11b channel 1 Mode: TX 11b channel 6

73 Reference No.: WTS17S E V1 Page 73 of 91 Mode: TX 11b channel 11 Mode :TX 11g channel 1

74 Reference No.: WTS17S E V1 Page 74 of 91 Mode :TX 11g channel 6 Mode :TX 11g channel 11

75 Reference No.: WTS17S E V1 Page 75 of 91 Mode: TX 11n HT20 channel 1 Mode: TX 11n HT20 channel 6

76 Reference No.: WTS17S E V1 Page 76 of 91 Mode: TX 11n HT20 channel 11 Mode: TX 11n HT40 channel 3

77 Reference No.: WTS17S E V1 Page 77 of 91 Mode: TX 11n HT40 channel 6 Mode: TX 11n HT40 channel 9

78 Reference No.: WTS17S E V1 Page 78 of 91 BLE: channel 0 BLE: channel 19

79 Reference No.: WTS17S E V1 Page 79 of 91 BLE: channel 39

80 Reference No.: WTS17S E V1 Page 80 of Power Spectral density Test Requirement: FCC CFR47 Part 15 Section Test Method: KDB D01 DTS Meas Guidance v03r05 April 8, Test Procedure: KDB D01 DTS Meas Guidance v03r05 April 8, 2016 section Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum. 2. Set the spectrum analyzer: RBW = 3kHz. VBW = 10kHz, Span = 1.5 times the DTS channel bandwidth(6 db bandwidth). Sweep = auto; Detector Function = Peak. Trace = Max hold. 3. Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. The limit is specified in one of the subparagraphs of this Section Submit this plot Test Result: Operation mode TX 11b TX 11g TX 11n HT20 TX 11n HT40 BLE Channel Frequency Power Spectral (MHz) (dbm per 3kHz) Limit Low dBm per 3kHz Middle dBm per 3kHz High dBm per 3kHz Low dBm per 3kHz Middle dBm per 3kHz High dBm per 3kHz Low dBm per 3kHz Middle dBm per 3kHz High dBm per 3kHz Low dBm per 3kHz Middle dBm per 3kHz High dBm per 3kHz Low dBm per 3kHz Middle dBm per 3kHz High dBm per 3kHz

81 Reference No.: WTS17S E V1 Page 81 of 91 Test Plot Mode: TX 11b channel 1 Mode: TX 11b channel 6

82 Reference No.: WTS17S E V1 Page 82 of 91 Mode: TX 11b channel 11 Mode :TX 11g channel 1

83 Reference No.: WTS17S E V1 Page 83 of 91 Mode :TX 11g channel 6 Mode :TX 11g channel 11

84 Reference No.: WTS17S E V1 Page 84 of 91 Mode: TX 11n HT20 channel 1 Mode: TX 11n HT20 channel 6

85 Reference No.: WTS17S E V1 Page 85 of 91 Mode: TX 11n HT20 channel 11 Mode: TX 11n HT40 channel 3

86 Reference No.: WTS17S E V1 Page 86 of 91 Mode: TX 11n HT40 channel 6 Mode: TX 11n HT40 channel 9

87 Reference No.: WTS17S E V1 Page 87 of 91 BLE: channel 0 BLE: channel 19

88 Reference No.: WTS17S E V1 Page 88 of 91 BLE: channel 39

89 Reference No.: WTS17S E V1 Page 89 of Antenna Requirement According to the FCC Part 15 Paragraph , an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. This product has an integrated antenna fulfill the requirement of this section.

90 Reference No.: WTS17S E V1 Page 90 of RF Exposure Remark: refer to SAR test report: WTS17S E.

91 Reference No.: WTS17S E V1 Page 91 of Photographs of test setup and EUT. Note: Please refer to appendix: WTS17S E_Photo. ======End of Report======