RF TEST REPORT 2APNR-GW631Q LTE CPE R1805A0254-R3V1

Transcription

1 RF TEST REPORT Applicant FCC ID Product Model Report No. Gosuncn Technology Group Co.,Ltd. 2APNR-GW631Q LTE CPE WF831, WF831+, WF831A, GW631 R185A254-R3V1 Issue Date June 6, 18 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 15C (17). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Xianqing Li Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: /2/3 FAX: /2/3 8

2 TABLE OF CONTENT 1. Test Laboratory Notes of the test report Test facility Testing Location General Description of Equipment under Test Applied Standards Test Configuration Test Case Results Average Power Output Conducted dB Bandwidth Band Edge Power Spectral Density Spurious RF Conducted Emissions Radiated Emissions in the Restricted Band Radiates Emission Conducted Emission Main Test Instruments ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance A.2 Test Setup TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 2 of 77

3 Summary of measurement results Number Summary of measurements of results Clause in FCC rules Verdict 1 Maximum Average conducted output power (b)(3) PASS 2 6 db bandwidth (a)(2) PASS 3 Power spectral density (e) PASS 4 Band Edge (d) PASS 5 Spurious RF Conducted Emissions (d) PASS 6 Radiated Emissions in restricted frequency bands (d),15.5,15.9 PASS 7 Radiated Emissions (d),15.5,15.9 PASS 8 Conducted Emissions 15.7 PASS Date of Testing: November 17, 17~ November 24, 17 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 3 of 77

4 1. Test Laboratory 1.1. Notes of the test report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein.measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. This report must not be used by the client to claim product certification, approval, or endorsement by any government agencies Test facility CNAS (accreditation number: L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (Designation number: CN1179, Test Firm Registration Number: ) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 85A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: ) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 4 of 77

5 1.3. Testing Location Company: Address: City: TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai Post code: 11 Country: Contact: P. R. China Xu Kai Telephone: /2/3 Fax: /2/3-8 Website: TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 5 of 77

6 2. General Description of Equipment under Test Client Information Applicant Applicant address Manufacturer Manufacturer address Gosuncn Technology Group Co.,Ltd. 6F, 2819 KaiChuang Blvd., Science Town, Huangpu District, Guangzhou City, Guangdong, China Gosuncn Technology Group Co.,Ltd. 6F, 2819 KaiChuang Blvd., Science Town, Huangpu District, Guangzhou City, Guangdong, China General information EUT Description Model WF831, WF831+, WF831A, GW631 IMEI Hardware Version V1. Software Version Power Supply Antenna Type Antenna Connector Antenna Gain additional beamforming gain Test Mode Modulation Type Max. Conducted Power Operating Frequency Range(s) ENTEL_PER_WF831_V1..B2 AC adapter Embeded Antenna A permanently attached antenna (meet with the standard FCC Part 15.3 requirement) Antenna 1: 1.5dBi Antenna 2: 1.5dBi db 82.11b 82.11g, 82.11n(HT/HT4); 82.11b: DSSS; 82.11g/n(HT/HT4): OFDM Wi-Fi 2.4G: 22.51dBm 82.11b/g/n(HT): 2412 ~ 2462 MHz 82.11n(HT4): 2422 ~ 2452 MHz EUT Accessory Adapter Network cable Manufacturer: AQUILSTAR PRECISION INDUSTRIAL (SHENZHEN)CO., LTD Model: ASSA65A-1 Manufacturer: SHANGHAI JINGTU ELECTRONICS LTD. Model: UTP CAT5E Note: The information of the EUT is declared by the manufacturer. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 6 of 77

7 Item WF831 WF831+ WF831A GW631 Protocol Stack The same The same The same The same MMS/STK The same The same The same The same JAVA The same The same The same The same Web User Interface page The same changes changes changes HARDWARE The same The same The same The same MECHANICAL The same The same The same The same ACCESSORY The same The same The same The same Note: Customer declaration, four models are the same, except for the logo and default parameters in the Web User Interface page, which will not affect the RF characteristic according to Part 2.43 requirement. This report tested WF831. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 7 of 77

8 3. Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: Test standards FCC CFR47 Part 15C (17) Radio Frequency Devices ANSI C63. (13) KDB D1 DTS Meas Guidance v4 KDB D1 Multiple Transmitter Output v2r1 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 8 of 77

9 4. Test Configuration Test Mode The EUT has been associated with peripherals and configuration operated in a manner tended to maximize its emission characteristics in a typical application. The radiated emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (Z axis) and the worst case was recorded. In order to find the worst case condition, Pre-tests are needed at the presence of different data rate. Preliminary tests have been done on all the configuration for confirming worst case. Data rate below means worst-case rate of each test item. The test software is used securecrt Worst-case data rates are shown as following table. Band Data Rate Antenna 1 Antenna 2 MIMO 82.11b 11 Mbps 11 Mbps / 82.11g 54Mbps 54 Mbps / 82.11n HT / / MCS n HT4 / / MCS7 The worst case Antenna mode for each of the following tests for Wi-Fi: Test Cases Antenna 1 Antenna 2 MIMO Average Power Output Conducted 82.11b/g 82.11b/g 82.11n HT 82.11n HT4 6dB Bandwidth -- Ο -- Band Edge -- Ο -- Power Spectral Density 82.11b/g 82.11b/g 82.11n HT 82.11n HT4 Spurious RF Conducted Emissions Ο Ο 82.11n HT 82.11n HT4 Radiates Emission in the Restricted Band -- Ο -- Radiates Emission b/g 82.11n HT 82.11n HT4 Conducted Emission b/g 82.11n HT 82.11n HT4 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 9 of 77

10 5. Test Case Results 5.1. Average Power Output Conducted Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Methods of Measurement During the process of the testing, The EUT was connected to Spectrum Analyzer with a known loss. The EUT is max power transmission with proper modulation. The Average detector is used. We use Maximum Average Conducted Output Power Level Method in KDB D1/KDB D1 for this test. The conducted Power is measured at each antenna port. The measured results at the various antenna ports are then summed mathematically. Test Setup Limits Rule Part (b) (3) specifies that " For systems using digital modulation in the MHz, MHz: 1 Watt. Average Output Power 1W (3dBm) Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U=.44 db. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page of 77

11 Test Results Packet Type Single Antenna Power Index Antenna 1 Antenna 2 CH1 CH6 CH11 CH1 CH6 CH b g Packet Type MIMO Antenna Power Index Antenna 1 Antenna 2 CH1 CH6 CH11 CH1 CH6 CH n HT Packet Type CH3 CH6 CH9 CH3 CH6 CH n HT Band T on (ms) T (on+off) (ms) Duty cycle Duty cycle correction Factor 82.11b NA 82.11g n HT n HT Note: when Duty cycle>.98, Duty cycle correction Factor not required. SISO Antenna 1 Network Standards 82.11b 82.11g Carrier frequency Read Value (MHz) (dbm) Average Output Limit Conclusion Power(dBm) (dbm) PASS PASS PASS PASS PASS PASS Note:Output Power=Read Value+Duty cycle correction factor TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 11 of 77

12 SISO Antenna 2 Network Standards 82.11b 82.11g Carrier frequency Read Value (MHz) (dbm) Average Output Limit Conclusion Power(dBm) (dbm) PASS PASS PASS PASS PASS PASS Note:Output Power=Read Value+Duty cycle correction factor MIMO Antenna 1 Antenna 2 Total Power Carrier Network Average Average Average frequency Read Read Standards Output Output Output (MHz) Value Value Power Power Power (dbm) (dbm) (dbm) (mw) (dbm) (mw) (mw) (dbm) 82.11n HT 82.11n HT4 Limit (dbm) Conclusion PASS PASS PASS PASS PASS PASS Note: 1. Output Power=Read Value+Duty cycle correction factor 2. For Total Power, according to KDB D1 Multiple Transmitter Output v2r1 1), The Total Power =log( (Power antenna1 in dbm/) + (Power antenna2 in dbm/) ). 3. The manufacturer declared the transmitter output signals is CDD mode. And N ss =1. According to KDB D1 Multiple Transmitter Output v2r1 2)f)(i): If all antennas have the same gain, Directional gain = G ANT + Array Gain, For power measurements on IEEE devices, Array Gain = db (i.e., no array gain) for N ANT 4; Array Gain = db (i.e., no array gain) for channel widths 4 MHz for any N ANT ; Array Gain = 5 log(n ANT /N SS ) db or 3 db, whichever is less, for -MHz channel widths with N ANT 5. So directional gain = G ANT + Array Gain =1.5+=1.5 dbi<6dbi. So the power limt is 3dBm TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 12 of 77

13 SISO Antenna b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: 11 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 13 of 77

14 SISO Antenna b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: 11 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 14 of 77

15 MIMO Antenna n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No. 9 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 15 of 77

16 MIMO Antenna n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No. 9 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 16 of 77

17 5.2. 6dB Bandwidth Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator and a known loss cable. RBW is set to khz; VBW is set to 3 khz on spectrum analyzer. Test Setup Limits Rule Part (a) (2) specifies that Systems using digital modulation techniques may operate in the MHz, MHz bands. The minimum 6 db bandwidth shall be at least 5 khz. minimum 6 db bandwidth 5 khz Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 936 Hz. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 17 of 77

18 Test Results: Network Standards Carrier frequency (MHz) 99% bandwidth (MHz) Minimum 6 db bandwidth (MHz) Limit (khz) Conclusion PASS 82.11b PASS PASS PASS 82.11g PASS PASS 82.11n HT 82.11n HT PASS PASS PASS PASS PASS PASS TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 18 of 77

19 82.11b, Carrier frequency (MHz): g, Carrier frequency (MHz): b, Carrier frequency (MHz): g, Carrier frequency (MHz): b, Carrier frequency (MHz): g, Carrier frequency (MHz):2462 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 19 of 77

20 82.11n(HT), Carrier frequency (MHz): n(HT4), Carrier frequency (MHz): n(HT), Carrier frequency (MHz): n(HT4), Carrier frequency (MHz): n(HT), Carrier frequency (MHz): n(HT4), Carrier frequency (MHz):2452 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page of 77

21 5.3. Band Edge Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator and a known loss cable the band edge of the lowest and highest channels were measured. The peak detector is used and RBW is set to khz and VBW is set to 3 khz on spectrum analyzer. Spectrum analyzer plots are included on the following pages. Test Setup Limits Rule Part (d) specifies that In any khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least db below that in the khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = Frequency 2GHz-3GHz Uncertainty 1.47 db TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 21 of 77

22 Test Results: PASS 82.11b, Channel No.: b, Channel No.: g, Channel No.: g, Channel No.: n(HT), Channel No.: n(HT), Channel No.: n(HT4), Channel No.: n(HT4), Channel No.: 9 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 22 of 77

23 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 23 of 77

24 5.4. Power Spectral Density Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator and a known loss cable. RBW is set to 3 khz and VBW is set to khz for Wi-Fi 2.4G on spectrum analyzer. Set the span to 1.5 times the DTS channel bandwidth. Sweep time = auto couple. Trace mode = max hold. The Average power spectral density is recorded. The conducted Power is measured at each antenna port. The measured results at the various antenna ports are then summed mathematically. Test setup Limits Rule Part (e) specifies that For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dbm in any 3 khz band during any time interval of continuous transmission. Limits 8 dbm / 3kHz Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U=.75dB. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 24 of 77

25 Test Results: SISO Antenna 1 Network Standards Channel Number Read Value (dbm / 3kHz) Power Spectral Density (dbm / 3kHz) Limit (dbm / 3kHz) Conclusion PASS 82.11b PASS PASS PASS 82.11g PASS PASS Note: Power Spectral Density =Read Value+Duty cycle correction factor SISO Antenna 2 Network Standards Channel Number Read Value (dbm / 3kHz) Power Spectral Density (dbm / 3kHz) Limit (dbm / 3kHz) Conclusion PASS 82.11b PASS PASS PASS 82.11g PASS PASS Note: Power Spectral Density =Read Value+Duty cycle correction factor TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 25 of 77

26 MIMO FCC RF Test Report Antenna 1 Antenna 2 Total PSD Read Network Channel Value Standards Number (dbm / Power Spectral Density (dbm / (mw/ Read Value (dbm / Power Spectral Density (dbm / (mw/ Power Spectral Density (mw/ (dbm / Limit (dbm / 3kHz) Conclusion 3kHz) 3kHz) 3kHz) 3kHz) 3kHz) 3kHz) 3kHz) 3kHz) 82.11n HT 82.11n HT PASS PASS PASS PASS PASS PASS Note: 1. Power Spectral Density =Read Value+Duty cycle correction factor 2. For Total PSD, according to KDB D1 Multiple Transmitter Output v2r1 2)a),the power spectral density=log( (PSD antenna1 in dbm/) + (PSD antenna2 in dbm/) ) 3. The manufacturer declared the transmitter output signals is CDD mode. And N ss =1. According to KDB D1 Multiple Transmitter Output v2r1 2)f)(i): If all antennas have the same gain, Directional gain = G ANT + Array Gain, For power spectral density (PSD) measurements on all devices, Array Gain = log(n ANT /N SS ) db=3.1. So directional gain = G ANT + Array Gain = =4.51 dbi<6dbi. So the power limt is 8dBm. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 26 of 77

27 SISO Antenna b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: 11 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 27 of 77

28 SISO Antenna b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: b, Channel No.: g, Channel No.: 11 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 28 of 77

29 MIMO Antenna n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No. 9 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 29 of 77

30 MIMO Antenna n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No n(HT), Channel No n(HT4), Channel No. 9 TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 3 of 77

31 5.5. Spurious RF Conducted Emissions Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Method of Measurement The EUT was connected to the spectrum analyzer with a known loss. The spectrum analyzer scans from 3MHz to the th harmonic of the carrier. The peak detector is used. Set RBW tokhz and VBW to 3 khz, Sweep is set to ATUO. The test is in transmitting mode. Test setup Limits Rule Part (d) pacifies that In any khz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least db below that in the khz bandwidth within the band that contains the highest level of the desired power. Antenna 1 Network Standards Carrier frequency (MHz) Reference value (dbm) Limit b g n HT n HT TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 31 of 77

32 Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = Frequency khz-2ghz 2GHz-26GHz Uncertainty.684 db 1.47 db TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 32 of 77

33 Test Results: Antenna 1 was selected as the worst case. Antenna 1 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz Frequency in GHz 82.11b CH1 3MHz to 18GHz 82.11b CH1 18GHz to 26.5GHz 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz Frequency in GHz 82.11b CH6 3MHz to 18GHz 82.11b CH6 18GHz to 26.5GHz - 1FCC WIFI CSE - - 1FCC WIFI CSE - -3 Level in dbm Level in dbm Frequency in GHz Frequency in GHz 82.11b CH11 3MHz to 18GHz 82.11b CH11 18GHz to 26.5GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 33 of 77

34 1FCC WIFI CSE 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11g CH1 3MHz to 18GHz Frequency in GHz 82.11g CH1 18GHz to 26.5GHz 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11g CH6 3MHz to 18GHz Frequency in GHz 82.11g CH6 18GHz to 26.5GHz 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11g CH11 3MHz to 18GHz Frequency in GHz 82.11g CH11 18GHz to 26.5GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 34 of 77

35 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11n (HT) CH1 3MHz to 18GHz Frequency in GHz 82.11n (HT) CH1 18GHz to 26.5GHz 1FCC WIFI CSE 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11n (HT) CH6 3MHz to 18GHz Frequency in GHz 82.11n (HT) CH6 18GHz to 26.5GHz 1FCC WIFI CSE - 1FCC WIFI CSE Level in dbm Level in dbm Frequency in GHz 82.11n (HT) CH11 3MHz to 18GHz Frequency in GHz 82.11n (HT) CH11 18GHz to 26.5GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 35 of 77

36 - 1FCC WIFI CSE - - 1FCC WIFI CSE - -3 Level in dbm Level in dbm Frequency in GHz Frequency in GHz 82.11n (HT4) CH3 3MHz to 18GHz 82.11n (HT4) CH3 18GHz to 26.5GHz - 1FCC WIFI CSE - - 1FCC WIFI CSE - -3 Level in dbm Level in dbm Frequency in GHz 82.11n (HT4) CH6 3MHz to 18GHz Frequency in GHz 82.11n (HT4) CH6 18GHz to 26.5GHz - 1FCC WIFI CSE - - 1FCC WIFI CSE - -3 Level in dbm Level in dbm Frequency in GHz 82.11n (HT4) CH9 3MHz to 18GHz Frequency in GHz 82.11n (HT4) CH9 18GHz to 26.5GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 36 of 77

37 5.6. Radiated Emissions in the Restricted Band Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Method of Measurement The Equipment Under Test (EUT) was set up on a non-conductive table in the semi-anechoic chamber. The test was performed at the distance of 3 m between the EUT and the receiving antenna. The turntable shall be rotated from to 36 degrees for detecting the maximum of radiated spurious signal level. The measurements shall be repeated with orthogonal polarization of the test antenna..the data of cable loss and antenna factor has been calibrated in full testing frequency range before the testing. Sweep the Restricted Band and the emissions less than db below the permissible value are reported. This method refer to KDB The procedure for peak unwanted emissions measurements above MHz is as follows: I) Peak emission levels are measured by setting the instrument as follows: 1) RBW = 1 MHz. 2) VBW [3 RBW] 3) Detector = peak. 4) Sweep time = auto. 5) Trace mode = max hold. 6) Allow sweeps to continue until the trace stabilizes. Note that if the transmission is not continuous, then the time required for the trace to stabilize will increase by a factor of approximately 1 / D, where D is the duty cycle. II) Average emission levels are measured by setting the instrument as follows: a) RBW = 1 MHz. b) VBW [3 RBW]. c) Detector = RMS (power averaging), if [span / (# of points in sweep)] RBW / 2. Satisfying this condition can require increasing the number of points in the sweep or reducing the span. If the condition is not satisfied, then the detector mode shall be set to peak. d) Averaging type = power (i.e., rms) (As an alternative, the detector and averaging type may be set for linear voltage averaging. Some instruments require linear display mode to use linear voltage averaging. Log or db averaging shall not be used.) e) Sweep time = auto. f) Perform a trace average of at least traces if the transmission is continuous. If the transmission is not continuous, then the number of traces shall be increased by a factor of 1 / D, where D is the duty cycle. For example, with 5% duty cycle, at least traces shall be averaged. (If a specific emission is demonstrated to be continuous i.e., % duty cycle then rather than turning ON and OFF with the transmit cycle, at least traces shall be averaged.) g) If tests are performed with the EUT transmitting at a duty cycle less than 98%, then a correction TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 37 of 77

38 factor shall be added to the measurement results prior to comparing with the emission limit, to compute the emission level that would have been measured had the test been performed at % duty cycle. The correction factor is computed as follows: 1) If power averaging (rms) mode was used in the preceding step e), then the correction factor is [ log (1 / D)], where D is the duty cycle. For example, if the transmit duty cycle was 5%, then 3 db shall be added to the measured emission levels. 2) If linear voltage averaging mode was used in the preceding step e), then the correction factor is [ log (1 / D)], where D is the duty cycle. For example, if the transmit duty cycle was 5%, then 6 db shall be added to the measured emission levels. 3) If a specific emission is demonstrated to be continuous (% duty cycle) rather than turning ON and OFF with the transmit cycle, then no duty cycle correction is required for that emission. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (Z axis) and the antenna is vertical. The test is in transmitting mode. Test setup Note: Area side: 2.4mX3.6m Limits Spurious Radiated Emissions are permitted in any of the frequency bands listed below: TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 38 of 77

39 Limit in restricted band Frequency of emission (MHz) Field strength(uv/m) Field strength Above (b) There is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to db above the maximum permitted average limit. Peak Limit=74 dbuv/m Average Limit=54 dbuv/m Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96, U= 3.55 db. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 39 of 77

40 Test Results: PASS Band T on (ms) T (on+off) (ms) Duty cycle Duty cycle correction Factor 82.11b NA 82.11g n HT n HT Note: when Duty cycle>.98, Duty cycle correction Factor not required. Antenna b-Channel 1 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V b-Channel 11 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V g-Channel 1 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V g-Channel 11 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 4 of 77

41 MIMO 82.11n HT -Channel 1 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V n HT-Channel 11 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V n HT4 -Channel 3 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V n HT4-Channel 9 Duty cycle conclusion Frequency Peak Average Height Azimuth Margin Limit Polarization correction value (MHz) (cm) (deg) Factor V V TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 41 of 77

42 5.7. Radiates Emission Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 2.5kPa Method of Measurement The test set-up was made in accordance to the general provisions of ANSI C The Equipment Under Test (EUT) was set up on a non-conductive table in the semi-anechoic chamber. The test was performed at the distance of 3 m between the EUT and the receiving antenna. The radiated emissions measurements were made in a typical installation configuration. Sweep the whole frequency band through the range from 9 khz to the th harmonic of the carrier, and the emissions less than db below the permissible value are reported. During the test, below 3MHz, the center of the loop shall be 1 meters; above 3MHz, the height of receive antenna shall be moved from 1 to 4 meters, and the antenna shall be performed under horizontal and vertical polarization. The turntable shall be rotated from to 36 degrees for detecting the maximum of radiated spurious signal level. The measurements shall be repeated with orthogonal polarization of the test antenna. The data of cable loss and antenna factor has been calibrated in full testing frequency range before the testing. Set the spectrum analyzer in the following: Below 1GHz (detector: Peak and Quasi-Peak) RBW= khz / VBW=3 khz / Sweep=AUTO Above 1GHz (detector: Peak): (a) PEAK: RBW=1MHz / VBW=3MHz/ Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=3MHz / Sweep=AUTO The radiated emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (Z axis) and the worst case was recorded. The test is in transmitting mode. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 42 of 77

43 Test setup 9KHz ~ 3MHz FCC RF Test Report 3MHz ~ 1GHz Above 1GHz Note: Area side:2.4mx3.6m TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 43 of 77

44 Limits Rule Part (d) specifies that In addition, radiated emissions which fall in the restricted bands, as defined in 15.5(a), must also comply with the radiated emission limits specified in 15.9(a) (see 15.5(c)). Limit in restricted band Frequency of emission (MHz) Field strength(uv/m) Field strength /F(kHz) / /F(kHz) / / Above (b) There is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to db above the maximum permitted average limit. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = Frequency 9KHz-3MHz 3MHz-MHz MHz-1GHz Above 1GHz Uncertainty 3.55 db 4.19 db 3.63 db 3.68 db TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 44 of 77

45 Test result Sweep from 9 khz to 3MHz, and the emissions more than db below the permissible value are not reported. The following graphs display the maximum values of horizontal and vertical by software. For above 1GHz, Blue trace uses the peak detection, Green trace uses the average detection. After the pre test, Antenna 2 was selected as the worst antenna. During the test, the Radiates Emission from 3MHz to 1GHz was performed in all modes with all channels, 82.11b, Channel 11 are selected as the worst condition. The test data of the worst-case condition was recorded in this report. Continuous TX mode: RE.3-1GHz QP Class B 8 7 Level in dbμv/ FCC Part 15(Class B) RE QP 3M M G Frequency in Hz Radiates Emission from 3MHz to 1GHz Reading Correct Frequency Quasi-Peak Height Polarizat Azimuth Margin Limit value Factor (MHz) (cm) ion (deg) V V V H H H Remark: 1. Quasi-Peak = Reading value + Correction factor 2. Correction Factor = Antenna factor+ Insertion loss(cable loss+amplifier gain) 3. Margin = Limit Quasi-Peak TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 45 of 77

46 82.11b CH1 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 46 of 77

47 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V H V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V H H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 47 of 77

48 82.11b CH6 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 48 of 77

49 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V H V V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V H V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 49 of 77

50 82.11b CH11 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 5 of 77

51 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 51 of 77

52 82.11g CH1 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 52 of 77

53 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V H V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 53 of 77

54 82.11g CH6 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 54 of 77

55 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V H V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V H V H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 55 of 77

56 82.11g CH11 FCC RF Test Report RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 56 of 77

57 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V V V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 57 of 77

58 82.11n (HT) CH1 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 58 of 77

59 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V H V H V V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V H V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 59 of 77

60 82.11n (HT) CH6 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 6 of 77

61 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V H V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V H V V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 61 of 77

62 82.11n (HT) CH11 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 62 of 77

63 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V H H H H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V H V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 63 of 77

64 82.11n (HT4) CH3 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 64 of 77

65 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V H V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 65 of 77

66 82.11n (HT4) CH6 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 66 of 77

67 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V V V Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 67 of 77

68 82.11n (HT4) CH9 RE 1G-3GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz RE 3-18GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) 3G 5G G 18G Frequency in Hz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 68 of 77

69 BELL_RE GHz PK+AV 9 Level in dbμv/ FCC RE PK(Class B) FCC RE AV(Class B) Frequency in GHz Radiates Emission from 18GHz to 26.5GHz Frequency (MHz) Peak Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit V V V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Frequency (MHz) Average Height (cm) Polarization Azimuth (deg) Reading value Correct Factor Margin Limit H V V V V H Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 69 of 77

70 5.8. Conducted Emission Ambient condition Temperature Relative humidity Pressure 23 C ~25 C 45%~5% 1.5kPa Methods of Measurement The EUT is placed on a non-metallic table of 8cm height above the horizontal metal reference ground plane. During the test, the EUT was operating in its typical mode. The test method is according to ANSI C Connect the AC power line of the EUT to the L.I.S.N. Use EMI receiver to detect the average and Quasi-peak value. RBW is set to 9 khz, VBW is set to 3kHz. The measurement result should include both L line and N line. The test is in transmitting mode. Test Setup Note: AC Power source is used to change the voltage 1V/6Hz. Limits Frequency (MHz) Quasi-peak Conducted Limits(dBμV) Average to 56 * 56 to 46 * *: Decreases with the logarithm of the frequency. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96, U= 2.69 db. TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 7 of 77

71 Test Results: Following plots, Blue trace uses the peak detection and Green trace uses the average detection. During the test, the Conducted Emission was performed in all modes with all channels, 82.11b, Channel 11 are selected as the worst condition. The test data of the worst-case condition was recorded in this report. L Line TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 71 of 77

72 N Line TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 72 of 77

73 6. Main Test Instruments Name Manufacturer Type Serial Calibration Expiration Number Date Date Spectrum Analyzer R&S FSV EMI Test Receiver R&S ESCI TRILOG Broadband Antenna Schwarzbeck VULB Double Ridged Waveguide Horn R&S HF Antenna Loop Antenna SCHWARZBECK FMZB Standard Gain Horn ETS-Lindgren EMI Test Receiver R&S ESCS LISN R&S ENV Power Sensor Keysight U21XA MY Spectrum Analyzer Agilent N9A MY RF Cable Agilent SMA 15cm Software (CE) Software (RE/RSE) ROHDE&SCHW ARZ ROHDE&SCHW ARZ EMC / / EMC / / *****END OF REPORT ***** TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 73 of 77

74 ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance a: EUT TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 74 of 77

75 b: Adapter c: Network cable Picture 1 EUT and Accessory TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 75 of 77

76 A.2 Test Setup 3M Hz-1GHz Above 1GHz Picture 2 Radiated Emission Test Setup TA Technology (Shanghai) Co., Ltd. TA-MB-4-5R Page 76 of 77