G-240WZ-A NOKIA. Brand. Model. Report No. October 21, Issue. TA Technology. compliance. by: Kai Xu. Approved

Transcription

1 RF TEST REPORT Applicant FCC ID Brand Product Model Report No. Issue Date Alcatel-Lucent Shanghai Bell Co., Ltd. 2ADZRG2WZA NOKIA Digital Home ONU G-2WZ-A YBA16-91RF2 October 21, 16 tested the above equipment in accordance with the requirements in FCC CFR47 Part 15C (16). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documentedd in this report. Performed by: Xianqing Li Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: /2/3 FAX: /2/3-

2 Table of Contents 1 Test Laboratory Notes of the Test Report Test facility Testing Location General Description of Equipment under Test Applied Standards Test Configuration Test Mode Occupied Bandwidth Radiated Emissions Conducted Emissions... 4 Main Test Instruments ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance A.2 Test Setup Page 2 of 36 This report shall not be reproduced except in full, withoutt the written approval of

3 Summary of Measurement Results Number Summary of measurements of Clause in FCC rules results Occupied Bandwidth (a),15.249(c),15.249(d),1 Radiated Emissionss 5.9,15.5; AC Power Line Conducted Emissions 15.7; Verdict PASS PASS PASS Date of Testing: April 12, 16 ~ May 14, 16 Page 3 of 36 This report shall not be reproduced except in full, withoutt the written approval of

4 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documentedd in this report apply only to the tested sample, under the conditions and modes of operation as described herein. Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. This report must not be used by the client to claim product certification, approval, or endorsement by CNAS or any government agencies. 1.2 Test facility CNAS (accreditation number: L2264) has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (recognition number is ) has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissionss measurements. IC (recognition number is 85A) has been listed by industry Canada to perform electromagnetic emission measurement. A2LA(Certificate Number: ) has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. Page 4 of 36 This report shall not be reproduced except in full, withoutt the written approval of

5 1.3 Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China City: Shanghai Post code: 11 Country: P. R. China Contact: Xu Kai Telephone: /2/3 Fax: /2/3- Website: Page 5 of 36 This report shall not be reproduced except in full, withoutt the written approval of

6 2 General Description of Equipment under Test Client Information Applicant Applicant addresss Manufacturer Manufacturer address Alcatel-Lucent Shanghai Bell Co., Ltd #,Ningqiao Road,Pudong Jinqiao, Shanghai P.R. China Taicang T& &W Electronics Co.,Ltd Jiangnan Road 89,Ludu Town, Taicang P.R. China General informationn Model: IMEI: HW Version: SW Version: Power Supply: Antenna Type: Test Mode(s): Tested Range(s): Modulation Type: Data rate: EUT Description G-2WZ-A / PEM 1+ 3FE458FFEB38 AC adapter ExternalAntenna z-wave 8.4 MHz, 8.42 MHz, 916. MHz FSK GFSK 9.6 kbps, kbps, kbps EUT Accessory Manufacture: DONGGUAN SHILONG FUHUA ELECTRONIC CO., LTD. Adapter 1 Model : UES36-SPA1 PN: UE1529GWAD1-P Manufacture: DONGGUAN SHILONG FUHUA ELECTRONIC CO.,LTD. Adapter 2 Model : UES36-SPA1 PN: UE1523GWAD1-P Manufacture: CyberPower Systems (USA), Inc. Adapter 3 Model : DTC36U12V3-G Note: The information of the EUT is declared by the manufacturer. Please refer to the specifications or user manual for details. Page 6 of 36 This report shall not be reproduced except in full, withoutt the written approval of

7 Configurations No. Name Model/Code No. Edition Serial No. or Quantity 1 G-2WZ-A 3FE 45688AABA PEM1 3 Power adapter UES36-SPA1 1 Auxiliary Equipment No. Name 1 SmartBits 2 OLT 3 Phone 4 Computer Brand name Model ASB code Spirent SMBB Alcatel-Lucent 73 ISAM FX-4 Valid Until Port description No. Port name Number Shielded or unshielded Cable type (optic, twisted pair, etc.) Max. Cable length 1 AC power 1 2 Gigabit Ethernet 4 Unshielded Multi twisted pair 3 POTS 2 unshielded Twisted pair 4 PON 1 unshielded Optic 5 USB 2 shielded Twisted pair Page 7 of 36 This report shall not be reproduced except in full, withoutt the written approval of

8 2.1 Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: Test standards FCC CFR47 Part 15C (16) Radio Devices ANSI C63. (13) Page 8 of 36 This report shall not be reproduced except in full, withoutt the written approval of

9 3 Test Configuration 3.1 Test Mode The EUT has been associated with peripherals and configuration maximize its emission characteristics in a typical application. operated in a manner tended to The radiated emission was measured in the following position: EUT stand-up position (X axis) and the position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down worst case was recorded. Page 9 of 36 This report shall not be reproduced except in full, withoutt the written approval of

10 3.2 Occupied Bandwidth Ambient condition Temperature 23 C ~25 C Relative humidity 45%~% % Pressure 1.5kPa Method of Measurement Tests are performed in accordance with ANSI C The db and 99% bandwidth of the fundamental frequency remain inside the band of operation of MHz.The EUT was connected to the spectrum analyzer and z-wave test set via a power splitter with a known loss. The occupied bandwidth is measured using spectrum analyzer. RBW is set to khz and VBW is set to khz on spectrum analyzer. Test Setup Limits No specific occupied bandwidth requirements in part (c). Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2. U= 1.19 db Page of 36 This report shall not be reproduced except in full, withoutt the written approval of

11 Test Results Mode Rate (kbit) db Bandwidth(kHz) 99% Bandwidth( (khz) z-wave Carrier frequency : 8.4 (9.6kbit) Carrier frequency : 8.4 (kbit) Carrier frequency : 916 Page 11 of 36 This report shall not be reproduced except in full, withoutt the written approval of

12 3.3 Radiated Emissions Ambient condition Temperature 23 C ~25 C Method of Measurement Relative humidity 45%~% % Pressure 1.5kPa The test set-up was made in accordance to the general provisions of ANSI C The Equipment Under Test (EUT) was set up on a non-conductive table in the semi-anechoic chamber. The test was performed at the distance of 3 m between the EUT and the receiving antenna. The radiated emissions measurements were made in a typical installation configuration. Sweep the whole frequency band through the range from 9 khz to the th harmonic of the carrier, and the emissions less than db below the permissiblee value are reported. During the test, below MHz, the center of the loop shall be 1 meters; above MHz, the height of receive antenna shall be moved from 1 to 4 meters, and the antennaa shall be performed under horizontal and vertical polarization. The turntable shall be rotated from to 3 degrees for detecting the maximum of radiated spurious signal level. The measurements shall be repeated with orthogonal polarization of the test antenna. The data of cable loss and antenna factor has been calibrated in full testing frequency range before the testing. Set the spectrum analyzer in the following: Below 1GHz (detector: Peak and Quasi-Peak) RBW=kHz / VBW=kHz / Sweep=AUTO Above 1GHz(detector: Peak): (a) PEAK: RBW=1MHz VBW=3MHz/ Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=3MHz / Sweep=AUTO The radiated emission was measured in the following position: EUT stand-up position (Z axis) and the position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up worst case was recorded. Then this mode was measured in the following mode: EUT with cradle and EUT without cradle. The worst emission was found in EUT with cradle mode and the worst case was recorded. The test is in transmitting mode. Page 12 of 36 This report shall not be reproduced except in full, withoutt the written approval of

13 Test setup 9KHz~~~ MHz MHz~~ ~~ 1GHz Above 1GHz Page 13 of 36 This report shall not be reproduced except in full, without the written approval of

14 Limits Limit in restricted band(part 15.9) of emission Above9- Field strength(uv/m) /F(kHz) /F(kHz) 1 Field strength( dbuv/m) / / / Limit in radiated emission measurement (Part 15.9) of emission Field Above 74 (peak) 54(average) Limit in radiated emission measurement (Part ) of emission Field strength of ( millivolts/meter) MHz fundamental MHzharmonics 94 Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = KHz-MHz MHz-MHz MHz-1GHz Above 1GHz Uncertainty 3.55 db 4.19 db 3.63 db 3.68 db Page 14 of 36 This report shall not be reproduced except in full, withoutt the written approval of

15 Test Results: Fundamental Field Strength 8.4MHz 8.42MHz in MHz in MHz 916MHz in MHz Page 15 of 36 This report shall not be reproduced except in full, withoutt the written approval of

16 Band edge 8.4MHz 8.42MHz 1.78 MHz 31.2 dbμv/ MHz 32.2 dbμv/ in MHz in MHz 916MHz MHz dbμv/ in MHz Page 16 of 36 This report shall not be reproduced except in full, withoutt the written approval of

17 8.4MHz FCCC RE 9K-KHz AV RE FCC Part15C 9kHz-MHz 9k k k k in Hz Radiated Emission 9K-KHz Average Reading value Height (cm) Azimuth (deg) Correct Factor Margin Limit FCC RE K-1KHz QP RE FCC Part15C 9kHz-MHz in khz Radiated Emission K-1KHz Page 17 of 36 This report shall not be reproduced except in full, withoutt the written approval of

18 FCC RE 1K-4KHz AV RE FCC Part15C 9kHz-MHz 1k 4k in Hz Average Radiated Emission 1KHz-4KHzz Reading value Height Azimuth Correct (cm) (deg) Factor Margin Limit FCC RE 4K-MHz QP RE FCC Part15C 9kHz-MHz 4k 1M 2M 3M 4M 5M 6 8 M M M in Hz Radiated Emission 4K-MHz Quasi-Peak Reading value Height Polariza (cm) tion Azimuth Correct (deg) Factor V Margin Limit Page 18 of 36 This report shall not be reproduced except in full, withoutt the written approval of

19 FCC RE.3-1GHz QP Class B FCC Part 15 RE QP(Class C) M M 1G in Hz Note: The signal beyond the limit is carrier. Radiated Emission M-1GHz Quasi-Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V V V V H V Remark: 1. Quasi-Peak = Reading value + Correction factor 2. Correction Factor = Antenna factor+ Insertion loss(cable loss+ +amplifier gain) 3. Margin = Limit Quasi-Peak Page 19 of 36 This report shall not be reproduced except in full, withoutt the written approval of

20 FCC RE PK FCC RE AV 1G 2G 3G 4G 5G G in Hz Radiated Emission 1G-GHz Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit H H V H V V Average Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V H V H V V Page of 36 This report shall not be reproduced except in full, withoutt the written approval of

21 8.42MHz FCCC RE 9K-KHz AV RE FCC Part15C 9kHz-MHz 9k k k k in Hz Radiated Emission 9kHz khz Average Reading value Height (cm) Azimuth (deg) Correct Factor Margin Limit Page 21 of 36 This report shall not be reproduced except in full, withoutt the written approval of

22 FCC RE K-1KHz QP RE FCC Part15C 9kHz-MHz in khz Radiated Emission khz 1kHz FCC RE 1K-4KHz AV RE FCC Part15C 9kHz-MHz 1k 4k in Hz Radiated Emission 1kHz 4kHz Average Reading value Height (cm) Azimuth (deg) Correct Factor Margin Limit Page 22 of 36 This report shall not be reproduced except in full, withoutt the written approval of

23 FCC RE 4K-MHz QP RE FCC Part15C 9kHz-MHz 4k 1M 2M 3M 4M 5M 6 8 M M M in Hz Radiated Emission 4K-MHz Quasi-Peak Reading value Height (cm) Azimuth (deg) Correct Factor Margin Limit Page 23 of 36 This report shall not be reproduced except in full, withoutt the written approval of

24 RE.3-1GHz QP Class B FCC Part 15 RE QP(Class C) M M 1G in Hz Note: The signal beyond the limit is carrier. Radiated Emission M-1GHz Quasi-Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V V V H H H Remark: 1. Quasi-Peak = Reading value + Correction factor 2. Correction Factor = Antenna factor+ Insertion loss(cable loss+ +amplifier gain) 3. Margin = Limit Quasi-Peak Page 24 of 36 This report shall not be reproduced except in full, withoutt the written approval of

25 FCC RE PK FCC RE AV 1G 2G 3G 4G 5G G in Hz Radiated Emission 1G-GHz Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit H H V H V H Average Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V H V H V H RE 3G-18GHz PK+AV Class B Page 25 of 36 This report shall not be reproduced except in full, withoutt the written approval of

26 916MHz FCCC RE 9K-KHz AV RE FCC Part15C 9kHz-MHz 9k k k k in Hz Radiated Emission 9kHz khz Average Reading value Height (cm) Azimuth (deg) Correct Factor Margin Limit FCC RE K-1KHz QP RE FCC Part15C 9kHz-MHz in khz Radiated Emission khz 1kHz Page 26 of 36 This report shall not be reproduced except in full, withoutt the written approval of

27 FCC RE 1K-4KHz AV RE FCC Part15C 9kHz-MHz 1k 4k in Hz Quasi-Peak Radiated Emission 1kHz 4kHz Reading Correct Height Azimuth value Factor (cm) (deg) Margin Limit FCC RE 4K-MHz QP RE FCC Part15C 9kHz-MHz 4k 1M 2M 3M 4M 5M 6 8 M M M in Hz Radiated Emission 4K-MHz Quasi-Peak Reading value Azimuth (deg) Correct Factor Margin Limit Page 27 of 36 This report shall not be reproduced except in full, withoutt the written approval of

28 RE.3-1GHz QP Class B FCC Part 15 RE QP(Class C) M M 1G in Hz Note: The signal beyond the limit is carrier. Radiated Emission M-1GHz Quasi-Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V V V H H H Remark: 1. Quasi-Peak = Reading value + Correction factor 2. Correction Factor = Antenna factor+ Insertion loss(cable loss+ +amplifier gain) 3. Margin = Limit Quasi-Peak Page 28 of 36 This report shall not be reproduced except in full, withoutt the written approval of

29 FCC RE PK FCC RE AV 1G 2G 3G 4G 5G G in Hz Radiated Emission 1G-GHz Peak Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit H H V V V V Average Reading value Height (cm) Polarization Azimuth (deg) Correct Factor Margin Limit V H H H V V Page 29 of 36 This report shall not be reproduced except in full, withoutt the written approval of

30 3.4 Conducted Emissionss Ambient condition Temperature 23 C ~25 C Relative humidity 45%~% % Pressure 1.5kPa Method of Measurement The EUT is placed on a non-metallic table of cm height above the horizontal metal reference ground plane. During the test, the EUT was operating in its typical mode. The test method is according to ANSI C Connect the AC power line of the EUT to the L.I.S.N. Use EMI receiver to detect the average and Quasi-peak value. RBW is set to 9 khz, VBW is set to khz.the measurement result should include both L line and N line. The test is in transmitting mode. Test Setup Note: AC Power source is used to change the voltage from 2V/Hz to 1V/Hz. Limits Quasi-peak Conducted Limits(dBμV) Average to * 56 to 46 * 46 *: D Decreases with the logarithm of the frequency. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2. U= 1.19 db Page of 36 This report shall not be reproduced except in full, withoutt the written approval of

31 Test Results: 8.4MHz L N 8.42MHz L N Page 31 of 36 This report shall not be reproduced except in full, without the written approval of

32 916MHz L N Page 32 of 36 This report shall not be reproduced except in full, without the written approval of

33 4 Main Test Instruments Name EMI Test Receiver EMI Test Receiver Loop Antenna Spectrum Analyzer Spectrum Analyzer Horn Antenna BT Base Station Simulator Loop Antenna EMI Test Receiver LISN EMI Test Receiver TRILOG Broadband Antenna Double Ridged Waveguide Horn Antenna Power Splitter Spectrum Analyzer Spectrum Analyzer Standard Gain Horn RF Cable Type Manufacturerr ESCS R&S ESCI R&S FMZB1519 FSV R&S NA Agilent HF7 R&S CBT R&S FMZB1519 SCHWARZBEC K ESCS R&S ENV216 R&S ESCI R&S Serial Calibration Number Date SHX-GF FSV NA 31-9 SMA 15cm Hua Xiang R&S Agilent ETS-Lindgrenn Agilent MY NA MY SCHWARZBEC K VULB 9163 Schwarzbeck HF7 R&S Expiration Time NA *****END OF REPORT ***** Page 33 of 36 This report shall not be reproduced except in full, withoutt the written approval of

34 ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance a: EUT Picture 1 EUT Page 34 of 36 This report shall not be reproduced except in full, withoutt the written approval of

35 A.2 Test Setup Below 1GHz Above 1GHz Picture 2 Radiated Emission Test Setup Page 35 of 36 This report shall not be reproduced except in full, withoutt the written approval of

36 Picture 3 Conducted Emission Test Setup Page 36 of 36 This report shall not be reproduced except in full, withoutt the written approval of