APPLICATION CERTIFICATION FCC Part 15C&RSS-247 On Behalf of Sunwoda Electronic Co., Ltd. Active stylus. Model No.: SPEN-HP-03

Transcription

1 Page 1 of 59 APPLICATION CERTIFICATION FCC Part 15C&RSS-247 On Behalf of Sunwoda Electronic Co., Ltd. Active stylus Model No.: SPEN-HP-03 FCC ID: 2ABWESPEN-HP-03 IC: SPENHP03 Prepared for : Sunwoda Electronic Co., Ltd. Address : No.2, Yihe Rd., Shilong Community, Shiyan Street, Baoan District, Shenzhen, China. Prepared by : Address : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China. Tel: (0755) Fax: (0755) Report No. : ATE Date of Test : Oct. 08, 2017-Oct. 17, 2017 Date of Report : Oct. 18, 2017

2 Page 2 of 59 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION Description of Device (EUT) Carrier Frequency of Channels Special Accessory and Auxiliary Equipment Description of Test Facility Measurement Uncertainty MEASURING DEVICE AND TEST EQUIPMENT OPERATION OF EUT DURING TESTING Operating Mode Configuration and peripherals TEST PROCEDURES AND RESULTS POWER LINE CONDUCTED MEASUREMENT Block Diagram of Test Setup Power Line Conducted Emission Measurement Limits Configuration of EUT on Measurement Operating Condition of EUT Test Procedure DATA SAMPLE Power Line Conducted Emission Measurement Results DB BANDWIDTH MEASUREMENT Block Diagram of Test Setup The Requirement For Section (a)(2) The Requirement for 5.2(1) EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Result MAXIMUM PEAK OUTPUT POWER Block Diagram of Test Setup The Requirement For Section (b)(3) The Requirement For Section RSS-247 section EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Result POWER SPECTRAL DENSITY MEASUREMENT Block Diagram of Test Setup The Requirement For Section (e) The Requirement For Section RSS-247 section EUT Configuration on Measurement Operating Condition of EUT Test Procedure... 23

3 Page 3 of Test Result BAND EDGE COMPLIANCE TEST Block Diagram of Test Setup The Requirement For Section (d) The Requirement For RSS-247 Section EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Result RADIATED SPURIOUS EMISSION TEST Block Diagram of Test Setup The Emission Limit Restricted bands of operation Restricted bands of operation Configuration of EUT on Measurement Operating Condition of EUT Test Procedure The Field Strength of Radiation Emission Measurement Results % OCCUPIED BANDWIDTH The Requirement for RSS-Gen Clause EUT Configuration on Measurement Operating Condition of EUT Test Procedure Measurement Result CONDUCTED SPURIOUS EMISSION COMPLIANCE TEST Block Diagram of Test Setup The Requirement For Section (d) EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Result ANTENNA REQUIREMENT The Requirement Antenna Construction... 59

4 Test Report Certification Report No.: ATE Page 4 of 59 Applicant : Sunwoda Electronic Co., Ltd. Address : No.2, Yihe Rd., Shilong Community, Shiyan Street, Baoan District, Shenzhen, China. Manufacturer : Sunwoda Electronic Co., Ltd. Address : No.2, Yihe Rd., Shilong Community, Shiyan Street, Baoan District, Shenzhen, China. Product : Active stylus Model No. : SPEN-HP-03 Trade name : hp Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart C Section ANSI C63.10: 2013 RSS-247 Issue 2 February 2017 RSS-Gen Issue 4 November 2014 The EUT was tested according to DTS test procedure of Apr 05, 2017 KDB D01 DTS Meas Guidance v04 for compliance to FCC 47CFR requirements. The device described above is tested by Shenzhen ACCURATE TECHNOLOGY CO. LTD to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart C Section and RSS-247. The measurement results are contained in this test report and Shenzhen ACCURATE TECHNOLOGY CO. LTD is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Shenzhen ACCURATE TECHNOLOGY CO. LTD. Date of Test : Oct. 08, 2017-Oct. 17, 2017 Date of Report: Oct. 18, 2017 Prepared by : ( Tim.zhang, Engineer) Approved & Authorized Signer : (Sean Liu, Manager)

5 Page 5 of GENERAL INFORMATION 1.1. Description of Device (EUT) EUT : Portable Speaker Model Number : SPEN-HP-03 HVIN : BIGBUN, MP255 Trade Name : hp Bluetooth version : BT V4.2 LE Frequency Range : 2402MHz-2480MHz Number of Channels : 40 Antenna Gain : 2dBi Antenna type : Internal Antenna Power Supply : DC 5V via Type-C interface for charging DC 3.7V, 50mA via built-in Lithium Battery Modulation mode : GFSK Applicant : Sunwoda Electronic Co., Ltd. Address : No.2, Yihe Rd., Shilong Community, Shiyan Street, Baoan District, Shenzhen, China Manufacturer : Sunwoda Electronic Co., Ltd. Address : No.2, Yihe Rd., Shilong Community, Shiyan Street, Baoan District, Shenzhen, China Date of sample received : Oct. 08, 2017 Date of Test : Oct. 08, 2017-Oct. 17, 2017

6 Page 6 of Carrier Frequency of Channels Channel Frequceny Frequceny Frequceny Channe Frequceny Channel Channel (MHz) (MHz) (MHz) l (MHz)

7 Page 7 of Special Accessory and Auxiliary Equipment PC Manufacturer: LENOVO M/N: 4290-RT8 S/N: R9-FW93G 11/ Description of Test Facility EMC Lab : Recognition of accreditation by Federal Communications Commission (FCC) The Designation Number is CN1189 The Registration Number is Listed by Innovation, Science and Economic Development Canada (ISEDC) The Registration Number is 5077A-2 Accredited by China National Accreditation Service for Conformity Assessment (CNAS) The Registration Number is CNAS L3193 Accredited by American Association for Laboratory Accreditation (A2LA) The Certificate Number is Name of Firm : Site Location : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China 1.5. Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty (9kHz-30MHz) Radiated emission expanded uncertainty (30MHz-1000MHz) Radiated emission expanded uncertainty (Above 1GHz) = 3.08dB, k=2 = 4.42dB, k=2 = 4.06dB, k=2

8 Page 8 of MEASURING DEVICE AND TEST EQUIPMENT Table 1: List of Test and Measurement Equipment Kind of equipment Manufacturer Type S/N Calibrated dates Calibrated until EMI Test Receiver Rohde&Schwarz ESCS Jan. 07, 2017 Jan. 06, 2018 EMI Test Receiver Rohde&Schwarz ESPI /003 Jan. 07, 2017 Jan. 06, 2018 Spectrum Analyzer Rohde&Schwarz FSV Jan. 07, 2017 Jan. 06, 2018 Spectrum Analyzer Agilent E7405A MY Jan. 07, 2017 Jan. 06, 2018 Pre-Amplifier Rohde&Schwarz CBLU Jan. 07, 2017 Jan. 06, Loop Antenna Schwarzbeck FMZB Jan. 13, 2017 Jan. 12, 2018 Bilog Antenna Schwarzbeck VULB Jan. 13, 2017 Jan. 12, 2018 Horn Antenna Schwarzbeck BBHA9120D 9120D-655 Jan. 13, 2017 Jan. 12, 2018 Horn Antenna Schwarzbeck BBHA Jan. 13, 2017 Jan. 12, 2018 Open Switch and Rohde&Schwarz OSP Jan. 07, 2017 Jan. 06, 2018 Control Unit OSP-B LISN Rohde&Schwarz ESH3-Z Jan. 07, 2017 Jan. 06, 2018 LISN Schwarzbeck NSLK Jan. 07, 2017 Jan. 06, 2018 Highpass Filter Wainwright Instruments Band Reject Filter Wainwright Instruments WHKX3.6/18 G-10SS N/A Jan. 07, 2017 Jan. 06, 2018 WRCG2400/2 N/A Jan. 07, 2017 Jan. 06, / /11SS

9 Page 9 of OPERATION OF EUT DURING TESTING 3.1. Operating Mode The mode is used: BLE Transmitting mode Low Channel: 2402MHz Middle Channel: 2440MHz High Channel: 2480MHz 3.2. Configuration and peripherals EUT Figure 1 Setup: Transmitting mode

10 Page 10 of TEST PROCEDURES AND RESULTS FCC&IC Rules Description of Test Result Section (a)(2) RSS-247 A5.2 Section (e) RSS-247 A5.2 Section (b)(3) RSS-247 A5.4 Section (d) RSS-247 A5.5 Section (d) Section RSS-247 A5.5 RSS-Gen 6.13 Section (d) RSS-Gen 6.2 6dB Bandwidth Test Power Spectral Density Test Maximum Peak Output Power Test Band Edge Compliance Test Radiated Spurious Emission Test Conducted Spurious Emission Test Compliant Compliant Compliant Compliant Compliant Compliant RSS-Gen Section % Occupied Bandwidth Compliant Section RSS-Gen Section 8.8 Section RSS-Gen 8.3 AC Power Line Conducted Emission Test Antenna Requirement Compliant Compliant

11 Page 11 of POWER LINE CONDUCTED MEASUREMENT 5.1. Block Diagram of Test Setup AC Mains Test Receiver L.I.S.N Adapter PC EUT (EUT: Active stylus) 5.2. Power Line Conducted Emission Measurement Limits Frequency Limit db( V) (MHz) Quasi-peak Level Average Level * * NOTE1: The lower limit shall apply at the transition frequencies. NOTE2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.50MHz Configuration of EUT on Measurement The following equipments are installed on Power Line Conducted Emission Measurement to meet the commission requirement and operating regulations in a manner, which tends to maximize its emission characteristics in a normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in test mode and measure it.

12 Page 12 of Test Procedure The EUT is put on the plane 0.8 m high above the ground by insulating support and is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC lines are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.10: 2013 on Conducted Emission Measurement. The bandwidth of test receiver (R & S ESCS30) is set at 9kHz. The frequency range from 150kHz to 30MHz is checked DATA SAMPLE Frequ ency (MHz) Quasi Peak Level (db v) Avera ge Level (db v) Trans ducer value (db) QuasiP eak Result (db v) Avera ge Result (db v) Quasi Peak Limit (db v) Avera ge Limit (db v) QuasiP eak Margin (db) Averag e Margin (db) X.XX Pass Transducer value = Insertion loss of LISN + Cable Loss Result = Quasi-peak Level/Average Level + Transducer value Limit = Limit stated in standard Calculation Formula: Margin = Limit Reading level value Transducer value Remark (Pass/Fail)

13 Page 13 of Power Line Conducted Emission Measurement Results PASS. The frequency range from 150kHz to 30MHz is checked. Test mode : CHARGING&BT Operation(worse case) Test Voltage: 120V/60Hz Emissions attenuated more than 20 db below the permissible value are not reported. The spectral diagrams are attached as below.

14 Page 14 of 59

15 Page 15 of 59

16 Page 16 of DB BANDWIDTH MEASUREMENT 6.1. Block Diagram of Test Setup PC EUT Test System PC (EUT: Active stylus) 6.2. The Requirement For Section (a)(2) Section (a)(2): Systems using digital modulation techniques may operate in the MHz, MHz, and MHz bands. The minimum 6 db bandwidth shall be at least 500 khz The Requirement for 5.2(1) The minimum -6 db bandwidth shall be 500 khz EUT Configuration on Measurement The equipment is installed on the emission measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit.

17 Page 17 of Test Procedure The transmitter output was connected to the spectrum analyzer through a low loss cable Set RBW of spectrum analyzer to 100 khz and VBW to 300 khz The 6dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6dB Test Result Channel Frequency (MHz) 6 db Bandwith (MHz) Minimum Limit(MHz) PASS/FAIL PASS PASS PASS The spectrum analyzer plots are attached as below. channel 0 Date: 9.OCT :29:24

18 Page 18 of 59 channel 19 Date: 9.OCT :30:54 channel 39 Date: 9.OCT :32:15

19 Page 19 of MAXIMUM PEAK OUTPUT POWER 7.1. Block Diagram of Test Setup PC EUT Test System PC (EUT: Active stylus) 7.2. The Requirement For Section (b)(3) Section (b)(3): For systems using digital modulation in the MHz, MHz, and MHz bands: 1 Watt The Requirement For Section RSS-247 section (4): For DTSs employing digital modulation techniques operating in the bands MHz and MHz, the maximum peak conducted output power shall not exceed 1W EUT Configuration on Measurement The equipment are installed on the emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit.

20 Page 20 of Test Procedure The transmitter output was connected to the spectrum analyzer through a low loss cable Set RBW of spectrum analyzer to 1 MHz and VBW to 3MHz Measurement the maximum peak output power Test Result Channel Frequency (MHz) Peak Power Output (dbm) Antenna gain (dbi) E.I.P.R. (dbm) Peak Power Limit (dbm) Pass / Fail PASS PASS PASS The spectrum analyzer plots are attached as below. channel 0 Date: 9.OCT :43:06

21 Page 21 of 59 channel 19 Date: 9.OCT :43:42 channel 39 Date: 9.OCT :44:27

22 Page 22 of POWER SPECTRAL DENSITY MEASUREMENT 8.1. Block Diagram of Test Setup PC EUT Test System PC (EUT: Active stylus) 8.2. The Requirement For Section (e) Section (e): For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dbm in any 3 khz band during any time interval of continuous transmission The Requirement For Section RSS-247 section 5.2 Section 5.2(2): The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater than 8dBm in any 3 khz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of Section 5.4(4), (i.e. the power spectral density shall be determined using the same method as is used to determine the conducted output power) EUT Configuration on Measurement The equipment are installed on the emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit.

23 Page 23 of Test Procedure The transmitter output was connected to the spectrum analyzer through a low loss cable Measurement Procedure PKPSD: This procedure must be used if maximum peak conducted output power was used to demonstrate compliance to the fundamental output power limit, and is optional if the maximum (average) conducted output power was used to demonstrate compliance. 1. Set analyzer center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS channel bandwidth. 3. Set the RBW to: 3 khz RBW 100 khz. 4. Set the VBW 3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level. 10. If measured value exceeds limit, reduce RBW (no less than 3kHz) and repeat Measurement the maximum power spectral density.

24 Page 24 of Test Result CHANNEL NUMBER FREQUENCY (MHz ) PSD (dbm/3khz) LIMIT (dbm/3khz) PASS/FAIL PASS PASS PASS The spectrum analyzer plots are attached as below. channel 0 Date: 9.OCT :46:52

25 Page 25 of 59 channel 19 Date: 9.OCT :46:03 channel 39 Date: 9.OCT :45:30

26 Page 26 of BAND EDGE COMPLIANCE TEST 9.1. Block Diagram of Test Setup PC EUT Test System PC (EUT: Active stylus) 9.2. The Requirement For Section (d) Section (d): In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in Section (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section (a), must also comply with the radiated emission limits specified in Section (a) The Requirement For RSS-247 Section : In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under Section 5.4(4), the attenuation required shall be 30 db instead of 20 db. Attenuation below the general field strength limits specified in RSS-Gen is not required EUT Configuration on Measurement The equipment are installed on the emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application.

27 Page 27 of Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2480MHz TX frequency to transmit Test Procedure Conducted Band Edge: The transmitter output was connected to the spectrum analyzer via a low loss cable Set RBW of spectrum analyzer to 100 khz and VBW to 300 khz Radiate Band Edge: The EUT is placed on a turntable, which is 0.1m above the ground plane and worked at highest radiated power The turntable was rotated for 360 degrees to determine the position of maximum emission level EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: RBW=1MHz, VBW=1MHz The band edges was measured and recorded Test Result Pass Channel Frequency Delta peak to band emission Limit(dBc) 0 2.4GHz GHz

28 Page 28 of 59 channel 0 Date: 9.OCT :36:19 channel 39 Date: 9.OCT :37:34

29 Radiated Band Edge Result Report No.: ATE Page 29 of 59

30 Page 30 of 59

31 Page 31 of 59

32 Page 32 of 59 Note: 1. Emissions attenuated more than 20 db below the permissible value are not reported. 2. The field strength is calculated by adding the antenna factor, high pass filter loss(if used) and cable loss, and subtracting the amplifier gain(if any)from the measured reading. The basic equation calculation is as follows: Result = Reading + Corrected Factor

33 Page 33 of RADIATED SPURIOUS EMISSION TEST 10.1.Block Diagram of Test Setup Block diagram of connection between the EUT and peripherals EUT Figure 1 Setup: Transmitting mode Semi-Anechoic Chamber Test Setup Diagram

34 (C) Radiated Emission Test Set-Up, Frequency above 1GHz Report No.: ATE Page 34 of 59 3 METERS EUT Cable 1.5 METER GROUND PLANE 10.2.The Emission Limit Measurement Limits According to RSS-Gen Section Table 5

35 Page 35 of Restricted bands of operation RSS-Gen Section Table 3: Restricted Frequency Bands (a) Unwanted emissions falling into restricted bands of Table 1 shall comply with the limits specified in RSS-Gen. (b) For licence-exempt transmitters employing pulsed operation for which an average power limit is specified, a peak power limit also applies. Unless otherwise specified, the peak power limit is 20 db above the average power limit. The average power measurement of the fundamental shall be performed according to the method described in RSS-Gen Section 4.5. The methodology described in Section 4.5 is also applicable to unwanted emission measurements provided that they exhibit similar pulse characteristics as the fundamental.

36 Page 36 of Restricted bands of operation FCC Part Restricted bands of operation (c) Except as shown in paragraph (d) of this section, Only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz ( 2 ) 1 Until February 1, 1999, this restricted band shall be Above 38.6 (d) Except as provided in paragraphs (d) and (e), the field strength of emission appearing within these frequency bands shall not exceed the limits shown in Section At frequencies equal to or less than 1000MHz, Compliance with the limits in Section shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000MHz, compliance with the emission limits in Section shall be demonstrated based on the average value of the measured emissions. The provisions in Section apply to these measurements Configuration of EUT on Measurement The equipment are installed on Radiated Emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application.

37 Page 37 of Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit Test Procedure The EUT and its simulators are placed on a turntable, which is 0.8 meter high above ground(below 1GHz). The EUT and its simulators are placed on a turntable, which is 1.5 meter high above ground(above 1GHz). The turntable can rotate 360 degrees to determine the position of the maximum emission level. EUT is set 3.0 meters away from the receiving antenna, which is mounted on an antenna tower. The antenna can be moved up and down between 1.0 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bi-log antenna) is used as receiving antenna. Both horizontal and vertical polarizations of the antenna are set on measurement. In order to find the maximum emission levels, all of the EUT location must be manipulated according to ANSI C63.10:2013 on radiated emission measurement. The EUT was tested in 3 orthogonal planes. The bandwidth of test receiver is set at 9 khz in below 30MHz. and set at 120 khz in MHz, and 1MHz in above 1000MHz. The frequency range from 9 khz to 25GHz is checked. The final measurement in band 9-90 khz, khz and above 1000MHz is performed with Average detector. Except those frequency bands mention above, the final measurement for frequencies below 1000MHz is performed with Quasi Peak detector. The field strength is calculated by adding the antenna factor, and cable loss, and subtracting the amplifier gain from the measured reading. The basic equation calculation is as follows: Result = Reading + Corrected Factor Where Corrected Factor = Antenna Factor + Cable Loss Amplifier Gain 10.8.The Field Strength of Radiation Emission Measurement Results PASS. Note: 1. Emissions attenuated more than 20 db below the permissible value are not reported. 2. *: Denotes restricted band of operation.

38 Page 38 of 59 FCC PART15C(9K-30MHz)(Worse case data) X(Antenna Polarization) Y(Antenna Polarization) Z(Antenna Polarization)

39 Page 39 of 59 FCC PART15C(30MHz-1000MHz)

40 Page 40 of 59

41 Page 41 of 59 FCC PART15C(1GHz-18GHz)

42 Page 42 of 59

43 Page 43 of 59

44 Page 44 of 59

45 Page 45 of 59

46 Page 46 of 59

47 Page 47 of 59 FCC PART15C(18GHz-26.5GHz)

48 Page 48 of 59

49 Page 49 of 59

50 Page 50 of 59

51 Page 51 of 59

52 Page 52 of 59

53 Page 53 of % OCCUPIED BANDWIDTH 11.1.The Requirement for RSS-Gen Clause When an occupied bandwidth value is not specified in the applicable RSS, the transmitted signal bandwidth to be reported is to be its 99% emission bandwidth, as calculated or measured EUT Configuration on Measurement The following equipment is installed on the emission measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit Test Procedure The transmitter output was connected to the spectrum analyzer through a low loss cable Set RBW of spectrum analyzer to 30 khz and VBW to 100 khz Set SPA Meas function, Select Occupied Bandwidth function, Select 99% Power Bandwidth. The frequency of the upper and lower markers indicating the edges of the transmitters 99% Power emission bandwidth shall be recorded to automate by SPA.

54 Page 54 of Measurement Result The EUT does meet the RSS-Gen requirement. Frequency (MHz) 99% Occupied Bandwidth (MHz) The spectrum analyzer plots are attached as below. Low Channel 2402MHz Date: 17.OCT :23:18

55 Middle Channel 2440MHz Report No.: ATE Page 55 of 59 Date: 17.OCT :24:17 High Channel 2480MHz Date: 17.OCT :24:46

56 Page 56 of CONDUCTED SPURIOUS EMISSION COMPLIANCE TEST 12.1.Block Diagram of Test Setup EUT Low Loss Cable Spectrum Analyzer (EUT: Active stylus) 12.2.The Requirement For Section (d) Section (d): In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in Section (a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section (a), must also comply with the radiated emission limits specified in Section (a) EUT Configuration on Measurement The equipment is installed on the emission measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipment Let the EUT work in TX modes measure it. The transmit frequency are MHz. We select 2402MHz, 2440MHz, and 2480MHz TX frequency to transmit.

57 Page 57 of Test Procedure The transmitter output was connected to the spectrum analyzer via a low loss cable Set RBW of spectrum analyzer to 100kHz and VBW to 300kHz The Conducted Spurious Emission was measured and recorded Test Result Pass. The spectrum analyzer plots are attached as below. Low Channel 2402MHz Date: 9.OCT :41:38

58 Page 58 of 59 Middle Channel 2440MHz Date: 9.OCT :40:22 High Channel 2480MHz Date: 9.OCT :39:29

59 Page 59 of ANTENNA REQUIREMENT 13.1.The Requirement According to Section , an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. According to Section RSS GEN 8.3, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device 13.2.Antenna Construction Device is equipped with permanent attached antenna, which isn t displaced by other antenna. The Antenna gain of EUT is 2dBi. Therefore, the equipment complies with the antenna requirement of FCC part 15C Section and RSS GEN 8.3.