TEST REPORT. Reference No... : WTS14S E FCC ID... : 2ADTE-DG700. Applicant... : Shenzhen KVD Communication Equipment

Transcription

1 TEST REPORT Reference No.... : WTS14S E FCC ID... : 2ADTE-DG700 Applicant... : Shenzhen KVD Communication Equipment Address... : 13C, Block C, Shenzhen Electronic Technology Building, Shennan Middle Road, Futian District, Shenzhen, China Manufacturer... : The same as above Address... : The same as above Product Name... : Mobile Phone Model No.... : TITANS2 DG700 Brand.. : DOOGEE Standards... : FCC PART15 SUBPART B: 2014 Date of Receipt sample... : Dec. 22, 2014 Date of Test... : Dec. 23, 2014 ~ Jan.12, 2015 Date of Issue... : Jan. 17, 2015 Test Result... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel : Fax: Compiled by: Approved by: Zero Zhou / Project Engineer Philo Zhong / Manager Page 1 of 43

2 Reference No.: WTS14S E Page 2 of 43 2 Test Summary Test Items Test Requirement Result RF Output Power (a) PASS (c) Peak-to-Average Ratio (d) PASS Bandwidth PASS Spurious Emissions at Antenna Terminal (a) PASS (a) Field Strength of Spurious Radiation (a) PASS (a) Out of band emission, Band Edge (a) (a) PASS Frequency Stability PASS Maximum Permissible Exposure (SAR) PASS

3 Reference No.: WTS14S E Page 3 of 43 3 Contents Page 1 COVER PAGE TEST SUMMARY CONTENTS GENERAL INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T TEST MODE TEST FACILITY EQUIPMENT USED DURING TEST EQUIPMENTS LIST MEASUREMENT UNCERTAINTY TEST EQUIPMENT CALIBRATION RF OUTPUT POWER EUT OPERATION TEST PROCEDURE TEST RESULT PEAK-TO-AVERAGE RATIO EUT OPERATION TEST PROCEDURE TEST RESULT BANDWITH EUT OPERATION TEST PROCEDURE TEST RESULT SPURIOUS EMISSIONS AT ANTENNA TERMINALS EUT OPERATION TEST PROCEDURE TEST RESULT SPURIOUS RADIATED EMISSIONS EUT OPERATION TEST SETUP SPECTRUM ANALYZER SETUP TEST PROCEDURE SUMMARY OF TEST RESULTS BAND EDGE MEASUREMENT EUT OPERATION TEST PROCEDURE TEST RESULT FREQUENCY STABILITY EUT OPERATION TEST PROCEDURE TEST RESULT RF EXPOSURE... 43

4 Reference No.: WTS14S E Page 4 of 43 4 General Information 4.1 General Description of E.U.T. Product Name :Mobile Phone Model No. :TITANS2 DG700 Model Description : N/A GSM Band(s) : GSM 850/900/1800/1900MHz GPRS/EGPRS Class : 12 WCDMA Band(s) : FDD Band I/II/V Wi-Fi Specification : b/g/n HT20/n HT40 Bluetooth Version : Bluetooth v4.0 with BLE GPS : Support NFC Hardware Version Software Version : N/A : D28-A2-BOM2 : DOOGEE-Titans2-DG Details of E.U.T. Operation Frequency Max. RF output power : GSM/GPRS 850: 824~849MHz GSM/GPRS 900: MHz DCS 1800: MHz PCS 1900: 1850~1910MHz WCDMA Band I: MHz WCDMA Band II: MHz WCDMA Band V: 824~849MHz WiFi: b/g/n HT20: MHz n HT40: MHz Bluetooth: MHz GPS: 1.57GHz : GSM 850: 32.78dBm PCS1900: 29.73dBm WCDMA Band II: 22.41dBm WCDMA Band V: 22.55dBm WiFi: 9.44dBm Bluetooth: 3.91dBm

5 Reference No.: WTS14S E Page 5 of 43 Type of Modulation Antenna installation Antenna Gain Technical Data Adapter Type of Emission : GSM,GPRS: GMSK WCDMA: QPSK WiFi: CCK, OFDM Bluetooth: GFSK, Pi/4 DQPSK,8DPSK : GSM/WCDMA: internal permanent antenna WiFi/Bluetooth: internal permanent antenna : GSM 850: -4.0dBi PCS1900: -4.0dBi WCDMA Band V: -4.0dBi WiFi: -1.0dBi Bluetooth: -1.0dBi : Battery DC 3.7V 4000mAh DC 5V, 2.0A, charging from adapter (Adapter Input: V~50/60Hz, 0.15A) : Manufacture: Shenzhen KVD Communication Equipment Model No.: DG70 : GSM850: 246KGXW,PCS1900: 243KGXW WCDMA BAND V: 4M16F9W, WCDMA BAND II: 4M20F9W 4.3 Test Mode All test mode(s) and condition(s) mentioned were considered and evaluated respectively by performing full tests, the worst data were recorded and reported. Support Band Test Mode Channel Frequency Channel Number GSM 850 PCS 1900 WCDMA Band V WCDMA Band II GSM/GPRS GSM/GPRS WCDMA/HSUPA/HSDPA WCDMA/HSUPA/HSDPA Remark: All mode(s) were tested and the worst data was recorded MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz 9538

6 Reference No.: WTS14S E Page 6 of Test Facility The test facility has a test site registered with the following organizations: IC Registration No.: 7760A Waltek Services(Shenzhen) Co., Ltd. Has been registered and fully described in a report filed with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our files. Registration number 7760A, July 12, FCC Test Site 1# Registration No.: Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , April 29, FCC Test Site 2# Registration No.: Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , December 3, 2014.

7 Reference No.: WTS14S E Page 7 of 43 5 Equipment Used during Test 5.1 Equipments List RF Conducted Test Item Equipment Manufacturer Model No. Serial No EMC Analyzer (9k~26.5GHz) Spectrum Analyzer (9k-6GHz) Agilent E7405A MY Last Calibration Date Calibration Due Date Aug. 15,2014 Aug. 14,2015 R&S FSL Aug. 15,2014 Aug. 14, Humidity Chamber GF GTH P IAA Aug. 15,2014 Aug. 14, Universal Radio Communication Tester R&S CMU Apr.11,2014 Apr.10,2015 3m Semi-anechoic Chamber for Radiated Emissions Test site 1# Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 EMC Analyzer Agilent E7405A MY Sep.15,2014 Sep.14, Active Loop Antenna Beijing Dazhi ZN30900A - Sep.15,2014 Sep.14, Trilog Broadband Antenna Coaxial Cable (below 1GHz) Broad-band Horn Antenna Broad-band Horn Antenna Broadband Preamplifier Coaxial Cable (above 1GHz) Broad-band Horn Antenna Universal Radio Communication Tester SCHWARZBECK VULB Apr.19,2014 Apr.18,2015 Top TYPE16(13M) - Sep.15,2014 Sep.14,2015 SCHWARZBECK BBHA 9120 D 667 Apr.19,2014 Apr.18,2015 SCHWARZBECK BBHA 9120 D 669 Apr.19,2014 Apr.18,2015 COMPLIANCE DIRECTION Top PAP-1G Mar.17,2014 Mar.16, MHz- 25GHz EW Apr.10,2014 Apr.09,2015 SCHWARZBECK BBHA Sep.15,2014 Sep.14,2015 R&S CMU Apr.11,2014 Apr.10, Signal Generator R&S SMR Sep.15,2014 Sep.14,2015

8 Reference No.: WTS14S E Page 8 of Measurement Uncertainty Parameter Uncertainty Radio Frequency ± 1 x 10-6 RF Power RF Power Density Radiated Spurious Emissions test Conducted Spurious Emissions test 5.3 Test Equipment Calibration ± 1.0 db ± 2.2 db ± 5.03 db (Bilog antenna 30M~1000MHz) ± 5.47 db (Horn antenna 1000M~25000MHz) ± 3.64 db (AC mains 150KHz~30MHz) All the test equipments used are valid and calibrated by CEPREI Certification Body that address is No.110 Dongguan Zhuang RD. Guangzhou, P.R.China.

9 Reference No.: WTS14S E Page 9 of 43 6 RF OUTPUT POWER Test Requirement: Test Method: Test Mode: FCC Part , (a), (c) ANSI C63.4:2003, TIA/EIA-603-D:2010 Transmitting 6.1 EUT Operation Operating Environment : Temperature: 22.5 C Humidity: 52.1 % RH Atmospheric Pressure: 101.2kPa 6.2 Test Procedure Conducted method: The RF output of the transmitter was connected to the wireless test set and the spectrum analyzer through sufficient attenuation. EUT Universal Radio Communication Radiated method: 1. The setup of EUT is according with per TIA/EIA Standard 603D:2010 and ANSI C measurement procedure. 2. The measurement antenna was placed at a distance of 3 meters from the EUT. During the tests, the antenna height and polarization as well as EUT azimuth were varied in order to identify the maximum level of emissions from the EUT. The test was performed by placing the EUT on 3-orthogonal axis. 3. The frequency range up to tenth harmonic of the fundamental frequency was investigated. 4. Remove the EUT and replace it with substitution antenna. A signal generator was connected to the substitution antenna by a non-radiating cable. The absolute levels of the spurious emissions were measured by the substitution.

10 Reference No.: WTS14S E Page 10 of Test Result Test Mode GSM 850 Conducted Power Cellular Band (Part 22H) Channel Frequency Peak Output Limit (MHz) Power(dBm) (dbm) Test Mode GPRS Channel Frequency Peak Output Power(dBm) Limit(dBm) (MHz) Slot 1 Slot 2 Slot 3 Slot Test Mode WCDMA Band V Channel Frequency Peak Output Power(dBm) Limit (MHz) RMC12.2k HSDPA1 HSDPA2 HSDPA3 HSDPA4 (dbm) Test Mode WCDMA Band V Channel Frequency Peak Output Power(dBm) Limit (MHz) HSUPA1 HSUPA2 HSUPA3 HSUPA4 HSUPA5 (dbm) Cellular Band (Part 24E) Test Mode PCS 1900 Channel Frequency Peak Output Limit (MHz) Power(dBm) (dbm)

11 Reference No.: WTS14S E Page 11 of 43 Test Mode GPRS Channel Frequency Peak Output Power(dBm) Limit(dBm) (MHz) Slot 1 Slot 2 Slot 3 Slot Test Mode WCDMA Band II Channel Frequency Peak Output Power(dBm) Limit (MHz) RMC12.2k HSDPA1 HSDPA2 HSDPA3 HSDPA4 (dbm) Test Mode WCDMA Band II Channel Frequency Peak Output Power(dBm) Limit (MHz) HSUPA1 HSUPA2 HSUPA3 HSUPA4 HSUPA5 (dbm)

12 Reference No.: WTS14S E Page 12 of 43 Frequency Receiver Reading Radiated Power(Measured at max. conducted power channel) ERP and EIRP Cellular Band (Part 22H) Turn table Angle RX Antenna Height Polar SG Level Substituted Cable Antenna Gain Absolute Level Part 22H Part 24E Limit Margin (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) GSM 850 Channel H V GPRS Channel H V Part 22H Turn RX Antenna Substituted Receiver Absolute Part 24E Frequency table Reading SG Antenn Level Margi Angle Height Polar Cable Limit Level a Gain n (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) WCDMA Band V Channel H V WCDMA Band V HSDPA Channel H V WCDMA Band V HSUPA Channel H V Remark: The test is without amplifier.

13 Reference No.: WTS14S E Page 13 of 43 Frequency Receiver Reading Turn table Angle Cellular Band (Part 24E) RX Antenna Height Polar SG Level Substituted Cable Antenna Gain Absolute Level Part 22H Part 24E Limit Margin (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) PCS 1900 Channel H V GPRS Channel H V Frequency Receiver Reading Turn table Angle RX Antenna Height Polar SG Level Substituted Cable Antenna Gain Absolute Level Part 22H Part 24E Limit Margin (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) WCDMA Band II Channel H V WCDMA Band II HSDPA Channel H V WCDMA Band II HSUPA Channel H V Remark: The test is without amplifier.

14 Reference No.: WTS14S E Page 14 of 43 7 Peak-to-Average Ratio Test Requirement: Test Method: Test Mode: (d) N/A Transmitting 7.1 EUT Operation Operating Environment : Temperature: 22.5 C Humidity: 52.3% RH Atmospheric Pressure: 101.2kPa 7.2 Test Procedure 1. The EUT was connected to spectrum analyzer and system simulator via a power divider. 2. Set EUT to transmit at maximum output power. 3. When the duty cycle is less than 98%, then signal gating will be implemented on the spectrum analyzer by triggering from the system simulator. 4. Set the CCDF (Complementary Cumulative Distribution Function) option of the spectrum analyzer. Record the maximum PAPR level associated with a probability of 0.1%. EUT RF Combiner Spectrum Analyzer Universal Radio Communication

15 Reference No.: WTS14S E Page 15 of Test Result Cellular Band (Part 24E) Mode PCS 1900 WCDMA Band II Channel Frequency (MHz) Peak-to- Average Ratio (db) Test Plots (Part 24E) PCS1900 Middle Channel

16 Reference No.: WTS14S E Page 16 of 43 WCDMA Band II Middle Channel

17 Reference No.: WTS14S E Page 17 of 43 8 Bandwith Test Requirement: FCC Part ,22.917,22.905, Test Method: ANSI C63.4:2003, TIA/EIA-603-D:2010 Test Mode: Transmitting 8.1 EUT Operation Operating Environment : Temperature: 22.5 C Humidity: 52.3% RH Atmospheric Pressure: 101.2kPa 8.2 Test Procedure The RF output of the transmitter was connected to the wireless test set and the spectrum analyzer through sufficient attenuation. The resolution bandwidth of the spectrum analyzer was set at 3 khz (Cellular /PCS) and the 26 db & 99%bandwidth was recorded. EUT RF Combiner Spectrum Analyzer Universal Radio Communication

18 Reference No.: WTS14S E Page 18 of Test Result Cellular Band (Part 22H) Test Mode Channel Frequency (MHz) 99% Occupied Bandwidth(kHz) 26 db Emission Bandwidth(kHz) GSM GPRS Test Mode Channel Frequency (MHz) 99% Occupied Bandwidth(MHz) 26 db Emission Bandwidth(MHz) RMC12.2k WCDMA HSDPA(16QAM) Band V HSUPA(BPSK) Cellular Band (Part 24E) Test Mode Channel Frequency (MHz) 99% Occupied Bandwidth(kHz) 26 db Emission Bandwidth(kHz) PCS GPRS Test Mode Channel Frequency (MHz) 99% Occupied Bandwidth(MHz) 26 db Emission Bandwidth(MHz) RMC12.2k WCDMA HSDPA(16QAM) Band II HSUPA(BPSK)

19 Reference No.: WTS14S E Page 19 of 43 Test Plots Cellular Band (Part 22H) GSM 850 GPRS

20 Reference No.: WTS14S E Page 20 of 43 WCDMA band V RMC12.2k HSDPA

21 Reference No.: WTS14S E Page 21 of 43 HSUPA Cellular Band (Part 24E) PCS 1900

22 Reference No.: WTS14S E Page 22 of 43 GPRS WCDMA band II RMC12.2k

23 Reference No.: WTS14S E Page 23 of 43 HSDPA HSUPA

24 Reference No.: WTS14S E Page 24 of 43 9 SPURIOUS EMISSIONS AT ANTENNA TERMINALS Test Requirement: Test Method: Test Mode: FCC Part ,22.917(a),24.238(a) ANSI C63.4:2003, TIA/EIA-603-D:2010 Transmitting 9.1 EUT Operation Operating Environment : Temperature: 23.5 C Humidity: 52.1 % RH Atmospheric Pressure: 101.3kPa 9.2 Test Procedure The RF output of the transceiver was connected to a spectrum analyzer and simulator through appropriate attenuation. The resolution bandwidth of the spectrum analyzer was set at 1MHz. Sufficient scans were taken to show any out of band emissions up to 10th harmonics. EUT RF Combiner Spectrum Analyzer Universal Radio Communication Tester

25 Reference No.: WTS14S E Page 25 of Test Result Remark: only the worst data were recorded. Cellular Band (Part 22H) GSM MHz-1GHz Above 1GHz

26 Reference No.: WTS14S E Page 26 of 43 WCDMA band V 30MHz-1GHz Above 1GHz

27 Reference No.: WTS14S E Page 27 of 43 Cellular Band (Part 24E) PCS MHz-1GHz Above 1GHz

28 Reference No.: WTS14S E Page 28 of 43 WCDMA band II 30MHz-1GHz Above 1GHz

29 Reference No.: WTS14S E Page 29 of SPURIOUS RADIATED EMISSIONS Test Requirement: FCC Part ,22.917, Test Method: Test Mode: ANSI C63.4:2003, TIA/EIA-603-D:2010 Transmitting 10.1 EUT Operation Operating Environment : Temperature: 23.5 C Humidity: Atmospheric Pressure: 52.1 % RH 101.2kPa 10.2 Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the ANSI C63.4: The test setup for emission measurement from 30 MHz to 1 GHz. Anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network

30 Reference No.: WTS14S E Page 30 of 43 The test setup for emission measurement above 1 GHz. Anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 1.5m Turn Table Absorbers PC System Spectrum Analyzer AMP Combining Network 10.3 Spectrum Analyzer Setup 30MHz ~ 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth kHz Video Bandwidth kHz Above 1GHz Sweep Speed... Auto Detector... PK Resolution Bandwidth... 1MHz Video Bandwidth... 3MHz Detector... Ave. Resolution Bandwidth... 1MHz Video Bandwidth... 10Hz

31 Reference No.: WTS14S E Page 31 of Test Procedure 1. The EUT is placed on a turntable, which is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. The spectrum was investigated from 30MHz up to the tenth harmonic of the highest fundamental frequency. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. The radiation measurements are tested under 3-axes(X,Y,Z) position(x denotes lying on the table, Y denotes side stand and Z denotes vertical stand), After pre-test, It was found that the worse radiation emission was get at the X position. So the data shown was the X position only. 7. Remove the EUT and replace it with substitution antenna. A signal generator was connected to the substitution antenna by a non-radiating cable. The absolute levels of the spurious emissions were measured by the substitution. Spurious emissions in db = 10 lg (TXpwr in Watts/0.001) the absolute level Spurious attenuation limit in db = Log10 (power out in Watts) 8. Repeat above procedures until the measurements for all frequencies are completed.

32 Reference No.: WTS14S E Page 32 of Summary of Test Results Remark: Test performed from 30MHz to 10 th harmonics with low/middle/high channels, only the worst data were recorded. Frequency Receiver Reading Turn table Angle RX Antenna Height Cellular Band (Part 22H) Polar SG Level Substituted Cable Antenna Gain Absolute Level Limit Result Margin (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) GSM 850 Channel H V H V H V WCDMA Band V Channel H V H V H V

33 Reference No.: WTS14S E Page 33 of 43 Frequency Receiver Reading Turn table Angle RX Antenna Height Cellular Band (Part 24E) Polar SG Level Substituted Cable Antenna Gain Absolute Level Limit Result Margin (MHz) (dbμv) Degree (m) (H/V) (dbm) (db) (db) (dbm) (dbm) (db) PCS 1900 Channel H V H V H V WCDMA Band II Channel H V H V H V Note: 1) The test is with an amplifier. 2) Absolute Level = SG Level - Cable loss + Antenna Gain 3) Margin = Limit- Absolute Level

34 Reference No.: WTS14S E Page 34 of Band Edge Measurement Test Requirement: Test Method: Test Mode: FCC Part ,22.917(a),24.238(a) ANSI C63.4:2003, TIA/EIA-603-D:2010 Transmitting 11.1 EUT Operation Operating Environment : Temperature: 23.5 C Humidity: 52.3 % RH Atmospheric Pressure: 101.3kPa 11.2 Test Procedure The RF output of the transmitter was connected to the input of the spectrum analyzer through sufficient attenuation. According to FCC Part (a), the power of any emissions outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least log(p) db. According to FCC Part (a), the power of any emissions outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least log(p) db. The center of the spectrum analyzer was set to block edge frequency EUT Attenuator Spectrum Analyzer Universal Radio Communication Tester

35 Reference No.: WTS14S E Page 35 of Test Result Cellular Band (Part 22H) Test Mode Frequency(MHz) Emission(dBm) Limit(dBm) GSM Test Mode Frequency(MHz) Emission(dBm) Limit(dBm) WCDMA Band V Cellular Band (Part 24E) Test Mode Frequency(MHz) Emission(dBm) Limit(dBm) PCS Test Mode Frequency(MHz) Emission(dBm) Limit(dBm) WCDMA Band II

36 Reference No.: WTS14S E Page 36 of 43 Test plots Cellular Band (Part 22H) GSM 850 band edge-left side GSM 850 band edge-right side

37 Reference No.: WTS14S E Page 37 of 43 WCDMA band V band edge-left side WCDMA band V band edge-right side

38 Reference No.: WTS14S E Page 38 of 43 Cellular Band (Part 24E) PCS 1900 band edge-left side PCS 1900 band edge-right side

39 Reference No.: WTS14S E Page 39 of 43 WCDMA band II band edge-left side WCDMA band II band edge-right side

40 Reference No.: WTS14S E Page 40 of FREQUENCY STABILITY Test Requirement: FCC Part ,22.355, Test Method: ANSI C63.4:2003, TIA/EIA-603-D:2010 Test Mode: Transmitting 12.1 EUT Operation Operating Environment : Temperature: 22.9 C Humidity: 52.0 % RH Atmospheric Pressure: 101.3kPa 12.2 Test Procedure Frequency Stability vs. Temperature: The equipment under test was connected to an external DC power supply and the RF output was connected to communication test set via feed-through attenuators. The EUT was placed inside the temperature chamber. The DC leads and RF output cable exited the chamber through an opening made for the purpose. After the temperature stabilized for approximately 20 minutes, the frequency output was recorded from the communication test set. Frequency Stability vs. Voltage: For hand carried, battery powered equipment; reduce primary supply voltage to the battery operating end point which shall be specified by the manufacturer. Humidity Chamber EUT Attenuator Universal Radio Communication Tester

41 Reference No.: WTS14S E Page 41 of Test Result Temperature ( ) 50 Power Supply (VDC) Cellular Band (Part 22H) GSM 850 Test Frequency:836.6MHz Frequency Error (Hz) Frequency Error (ppm) Limit (ppm) Temperature ( ) 50 WCDMA Band V Test Frequency:836.6MHz Power Supply (VDC) Frequency Error (Hz) Frequency Error (ppm) Limit (ppm)

42 Reference No.: WTS14S E Page 42 of 43 Temperature ( ) 50 PCS Band (Part 24E) PCS 1900 Test Frequency:1880.0MHz Power Supply (VDC) Frequency Error (Hz) Frequency Error (ppm) Limit (ppm) Temperature ( ) 50 WCDMA Band II Test Frequency:1880.0MHz Power Supply (VDC) Frequency Error (Hz) Frequency Error (ppm) Limit (ppm)

43 Reference No.: WTS14S E Page 43 of RF Exposure Please refer to SAR test report: STR H. ====== End of Report ======