2009 ODU Point and Peak Job Aid
|
|
- Janice Wells
- 5 years ago
- Views:
Transcription
1 Summary This Job Aid covers: Preparing the Antenna for Pointing and Peaking Point Elevation Set the Skew Point Azimuth Peak Azimuth Peak Elevation Push/Pull Test This Job Aid supports all Technician audiences. Preparing the Antenna for Pointing and Peaking The following information reviews the steps necessary to prepare the satellite modem and the Ka-band antenna to support the WildBlue Point and Peak process. The Technician is required to complete this process during every WildBlue Service installation. Warning: Confirm that the modem is unplugged from the wall before beginning any preparation steps Setting "Zero" Before aligning an antenna, confirm that these items are present. These three settings represent the "zero" settings. The Elevation gauge is set to the work order elevation The Azimuth Fine-adjust cam notch is aligned with the hash mark o If not, loosen the Azimuth base plate bolts, and rotate the cam clockwise until the notch and mark are aligned. Use the ½-inch open wrench for this step The Skew is set for 90 degrees Required Tools To point and peak a 2009 ODU, an Technician needs these tools: Two COAX Test cables A Satellite Signal Level Meter (SSLM) The WildBlue Antenna Pointing Aid (APA) Two WildBlue Attenuators 10dB and 20dB An inclinometer ½-inch open wrench ½-inch ratchet and socket ViaSat, Inc. Page 1 of 8
2 Follow these steps to prepare the antenna for pointing and peaking. 1. Insert the tools in the Receive (RX) feed cable path. a. Beginning at the TRIA, place a test cable from the RX port to the From TRIA port on the APA. b. From the To Meter port on the APA, place a test cable to the LNB port on the SSLM. c. From the Sat RX port on the SSLM to the 10dB attenuator, place the installed COAX cable. Note: We recommend attaching the Attenuators with the 20 db attached directly to the modem RX connector. It makes it easier to remove the 10 db Attenuator, if necessary. 2. Set the APA to the frequency range setting (1-8) provided on the work order. Note that the filter setting may be different from carrier to carrier with in a beam, and may change over time. 3. Plug the modem AC power cord into the power outlet. 4. Confirm that the SSLM produces an audible signal, and adjust the gain appropriately ViaSat, Inc. Page 2 of 8
3 Point Elevation The following information reviews the steps to complete the point (coarse) antenna Elevation adjustment. 1. Slightly loosen the Lockdown Nuts in the Arched Slots on sides of the Elevation Bracket. Next, turn the top ½-inch Nut on the Elevation Rod away from the top of the Pivot Casting. 2. Set the marker on the Inclinometer to the Arm angle shown on the work order. Attach a magnetic Inclinometer to one of the Boom Arms. 3. Turn the Bottom Nut in the direction necessary to align the Inclinometer arrow to the Arm Angle. 4. Handtighten the top nut on the Elevation rod to the Pivot Casting. Finally, tighten the Lockdown Nuts in the Arched Slots on each side of the Elevation Bracket ViaSat, Inc. Page 3 of 8
4 Set the Skew After pointing the Elevation, the antenna is skewed using the setting found on the work order. Follow these steps to set the Skew. 1. Locate the skew setting on the work order. 2. Loosen the four bolts that hold the Antenna Back Bracket to the Skew plate Rotate the reflector dish so that the Skew pointer aligns with the Skew setting on the scale. 4. Tighten the four bolts ViaSat, Inc. Page 4 of 8
5 Point Azimuth The following information reviews the steps to complete the point (coarse) antenna Azimuth adjustment. Satellite Locations The three WildBlue Network satellites are Anik F2, WB1, and AMC- 15. Anik F2 and WB1 are located at 111 degrees, while AMC 15 is located at 105 degrees. 1. Sweep the antenna from side to side, checking the tightness of the three flange nuts on the mount canister. The antenna should move, but not too easily. Tighten or loosen the flange nuts as needed. Note: After placing the antenna on the mount tube, the Technician aligned it to the desired compass setting. 2. The direction of this procedure depends on the satellite noted on the work order or on the Support Portal Quick Flash Tab. WildBlue 1 and Anik F2: Gently pull the dish to the right about 10 degrees away from the estimated Azimuth. AMC-15: Gently pull the dish to the left about 10 degrees away from the estimated Azimuth. 3. Sweep the antenna in the opposite direction until the SSLM registers its highest tone and reading 4. Finish this step by tightening the Flange nuts, starting with the top to maintain an even pressure on the Tube canister ViaSat, Inc. Page 5 of 8
6 Peak Azimuth The following information reviews the steps to complete the peak (fine) antenna Azimuth adjustment. 1. Loosen the three Azimuth base plate bolts using a ½-inch ratchet. If the Cam notch and Hash mark are not aligned, turn the cam clockwise until the notch and mark are aligned. 2. Set the gain on the SSLM to Using the ½-inch open wrench, turn the Cam clockwise. Watch/listen as the Signal Meter registers the highest tone/reading. Note that reading. 4. Continue turning the Cam clockwise until the Signal Meter drops, and then returns to its highest reading/tone, as noted in 3 above. Stop. Important: Never turn the CAM backwards. This breaks the Cam and prevents correct peaking. 5. Finish this step by tightening the carriage bolts on the Azimuth base ViaSat, Inc. Page 6 of 8
7 Peak Elevation The following information reviews the steps to complete the peak (fine) antenna Elevation adjustment. 1. Slightly loosen the Lockdown Nuts in the Arched Slots on sides of the Elevation Bracket. Next, turn the top ½-inch Nut on the Elevation Rod away from the top of the Pivot Casting. 2. Set the Signal Meter to Using the ½-inch wrench on the lower nut of the Elevation rod, watch/listen as the Signal Meter registers the lowest tone/reading. Note this reading (i.e., 20.) 4. Reverse the turn on the nut, and count revolutions as the Signal Meter registers its highest tone/reading, and then comes back to reading noted in Reverse the turn on the nut again, and turn half of the revolutions from Finish this step by tightening the same bolts and nuts ViaSat, Inc. Page 7 of 8
8 Push/Pull Test The following information reviews the steps to complete the peak (fine) antenna Azimuth adjustment. Important: An Technician always uses a Push/Pull test before proceeding to Initial Modem Lock. This prevents delays in Modem Lock and Provisioning because the Push/Pull Test confirms that the antenna has aligned correctly during Point and Peak. 1. From behind the antenna, gently push and pull each side of the antenna. 2. Gently push and pull the top and the bottom of the antenna 3. The test passes when the SSLM tone and reading drops every time pressure is added to the antenna. If the tone or reading rises, the alignment is not correct. If the rise occurs when pushing or pulling on the sides of the antenna, restart at the Point Elevation step. If the rise occurs when pushing or pulling on the top or bottom of the antenna, restart at the Point Azimuth step. Note: Remember to zero the Azimuth fine-adjust Cam before beginning any azimuth steps ViaSat, Inc. Page 8 of 8
2005 ODU Point & Peak Job Aid
Summary This Job Aid covers: Preparing the Antenna for Pointing and Peaking Point Elevation Set the Skew Point Azimuth Peak Azimuth Peak Elevation Push/Pull Test This Job Aid supports all Technician audiences.
More information75cm ODU/SurfBeam 2 Point and Peak Job Aid
Summary This Job Aid covers: 75cm ODU/SurfBeam 2 Point and Peak Job Aid Preparing the Antenna for Pointing and Peaking Configure the SurfBeam 2 Modem and 75cm TRIA Point Elevation Set the Skew Point Azimuth
More information75 cm ODU (VS1300) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly Transport On Site Assembly This Job Aid supports all Technician audiences. This job aid covers the VS1200 ODU
More information75 cm ODU (VS1300 with the SurfBeam2 TRIA) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly TRIA, TRIA Bracket, and Boom Arm Assembly This Job Aid supports all Technician audiences. This job aid covers
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationQDV120 Operation and Pointing manual
QDV120 Operation and Pointing manual MPAD1 Plus OP-080316-E1 page 1 Contents Item Description Page 1.0 Health and Safety for Operators and Installation Staff 3 2.0 Transit case Reflector/Mount/BUC/LNB
More informationInstallation Guide. 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD
Installation Guide 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD Contents Introduction 1 Specifications 1 Safety Notice 2 Package Contents 2 Installation Requirements 3 Hardware Overview 3 Hardware
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More informationParadigm. Connect100 Installation Guide
Paradigm GX Connect100 Installation Guide Paradigm GX Safe Use WARNING Radiation Hazard. Transmitter power levels are sufficient to cause blindness or other serious injury to body tissue. Do not power
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationSERIES M Ku-BAND Rx / Tx ANTENNA SYSTEM
4096-432 June 15, 2011 REVISION D ASSEMBLY MANUAL SERIES 1125 1.2M Ku-BAND Rx / Tx ANTENNA SYSTEM General Dynamics 1500 PRODELIN DRIVE NEWTON, NC 28658 PRODELIN CORPORATION 4096-432 SERIES 1125 1.2M Ku-BAND
More information1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM
REVISION H April 20, 2016 ASSEMBLY MANUAL 1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 1.2
More informationSatellite Terminal. Installation Guide. Release 2.2 Ref. nr
Satellite Terminal Installation Guide Release 2.2 Ref. nr. 37628 Table of Contents Table of Contents Table of Contents... 2 1 Introduction... 3 1.1 About this Guide... 3 1.2 Material Provided in the Box...
More informationMESA-HPX. Assembly and Installation Manual. w/appendix A for Prodelin Antenna. 901-Manual-MESA-HPX
MESA-HPX Assembly and Installation Manual w/appendix A for Prodelin Antenna 901-Manual-MESA-HPX Rev 30 March 2011 2 INDEX Installation Cautions 4 Installation Pole Height Orientation of the Mount on the
More informationC-COM Satellite Systems Inc. Page 1 of 39
Page 1 of 39 inetvu Fly-75V & Fly-98G/H/V & Fly-981 User Manual The inetvu brand and logo are registered trademarks of C-COM Satellite Systems, Inc. Copyright 2006 C-COM Satellite Systems, Inc. 1-877-iNetVu6
More informationABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationRotary Fixture M/V/X CLASS LASER SYSTEMS. Installation and Operation Instructions
Rotary Fixture M/V/X CLASS LASER SYSTEMS Installation and Operation Instructions 02/01/2000 Introduction The Rotary Fixture controls in the Printer Driver are used along with the optional Rotary Fixture
More information1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More informationInstalling the Hughes BGAN Remote Antenna
Installing the Hughes BGAN Remote Antenna Product description BGAN Remote Antenna The Hughes BGAN Remote Antenna (HNS Part No. 9501286-0001) is designed to be permanently installed with the Basic Fixed
More informationInstallation Instructions
Installation Instructions For 0.2m Ultra-high Performance Antenna Model ADxxG-0-T2 Before Installation, please read these instructions carefully. This instruction guide is for the installation of 8 inch
More informationMEC Auto-Mate Assembly Manual. For MEC 9000G/GN and 8567 Grabber Series
MEC Auto-Mate Assembly Manual For MEC 9000G/GN and 8567 Grabber Series Thank you We really appreciate your support of our product line. But our commitment to you hardly ends here. We won't be satisfied
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationPolaris XP Doors (P144202) Installation Instructions
Polaris XP4 000 Doors (P440) Installation Instructions WARNING Pro Armor Door and Net are designed to work together to replace your original equipment nets and/or door. Install both the Pro Armor Door
More informationPole Mount Installation Guide
Pole Mount Installation Guide (No Fine Adjustment) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More information.74m Ka-Band Antenna Installation Guide Model: AN8-074P
.74m Ka-Band Antenna Installation Guide Model: AN8-074P 1037749-0001 Revision B September 12, 2008 Revision record Revision Date of issue Scope A March 26, 2008 Production Release B September 12, 2008
More informationReferencing 0,0 position
Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how
More informationRemarks: Before Installation, please read the instruction carefully.
30 cm antenna Z24A30T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.3m ultra-high performance microwave antenna. Installation,
More information.98m Ka-Band Antenna Installation Guide Model: AN8-098R
.98m Ka-Band Antenna Installation Guide Model: AN8-098R 1037752-0001 Revision A June 17, 2008 Revision record Revision Date of issue Scope A June 17, 2008 Production Release Copyright 2008 Hughes Network
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationElectric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
More informationAPES HD-7700 Version Operator s Training Manual
APES-14-77 HD-7700 Version Operator s Training Manual Issue A1 09/03 P/N 900599 Performance Design Inc. 2350 East Braniff St. Boise Idaho 83716 This manual contains very important safety information and
More information2.4 Meter 4 Piece C-Band Rx/Tx Antenna Feed System
4096-354 Revision B July 14, 2009 ASSEMBLY MANUAL 2.4 Meter 4 Piece C-Band Rx/Tx Antenna Feed System General Dynamics 1500 PRODELIN DRIVE NEWTON, NC 28658 2.4 Meter C-Band Rx/Tx Antenna Feed System B Revised
More informationTL4100 Top 5 Build Tips
TL4100 Top 5 Build Tips 1: Top Plate When assembling the top plate, align the top of the top plate brackets with the top of the rods. This can be done by placing a hard flat object (such as a ruler) on
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationPERSONAL RECORD KEEPING
2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain
More information1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM
August 21, 1997 Revision D ASSEMBLY MANUAL 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM PRODELIN CORPORATION 1700 NE CABLE DRIVE CONOVER, NC 28613-0368 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM D
More informationNewHeights Presidente Reception Assembly Instructions Warranty: raproducts.com/warranty
NewHeights Presidente Reception Assembly Instructions Warranty: raproducts.com/warranty Failure to comply with or observe all assembly, safety, and operation instructions and warnings regarding use of
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationTHIS SHOULD TWEAK YOUR IMAGINATION
10-27-05 THIS SHOULD TWEAK YOUR IMAGINATION SPECIFICATIONS FOR SINGLE ANTENNA MODEL NUMBER... 432EME-12 FREQUENCY... 430-436 MHz GAIN... 14.4 dbd FRONT TO BACK... 23 db VSWR... 1.2:1 TYPICAL BEAMWIDTH...
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationS-85SCH
4411-4423-4432-4443-4452 5511-5523-5532-5554 44S-85SCH Service Manual 104 73 14-26 2014-02-24 CONTENTS 1. Names of principal parts...2 2. Removing methods of external parts 2-1 Sewing table...3 2-2 Face
More information3 GHz Carrier Backhaul Radio. Model: AF-3X. Tel: +44 (0) Fax: +44 (0) LINK GPS MGMT DATA DATA
LINK GPS MGMT DATA DATA MGMT GPS LINK 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you
More informationCrank-up Satellite TV System Satellite Antenna with Lift and Rotation Unit - Manual
Crank-up Satellite TV System Satellite Antenna with Lift and Rotation Unit - Manual Distributed in the U.K. by: 1. Contents: www.camos-multimedia.com Quantity Description 1 Antenna Selfsat HD 10 1 Lift
More informationHQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1
HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included
More informationHN System. Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074P
HN System Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074P 1037087-0001 Revision B October 19, 2006 Copyright 2006 Hughes Network Systems, LLC All rights reserved. This publication
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationHughes. Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074S
Hughes Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074S 1036469-0001 Revision D March 31, 2006 Copyright 2005, 2006 Hughes Network Systems, LLC All rights reserved. This publication
More information0.98 m Ka-Band Antenna Installation Guide
0.98 m Ka-Band Antenna Installation Guide Model: AN8-098-G 1040579-0001 Revision A.04 April 30, 2015 11717 Exploration Lane, Germantown, MD 20876 Phone (301) 428-5500 Fax (301) 428-1868/2830 Copyright
More informationKU-BAND FEED INSTALLATION OMT INTERFACE
Revision D April 22, 2016 Assembly Manual KU-BAND FEED INSTALLATION OMT INTERFACE General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com KU-BAND
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationEasy Step by Step Manual
Easy Step by Step Manual Teletower Mini XL Wall-Floor installation The tower packages #1-#2-#3 Open Base Package #1 for the main tower parts. Here you see the three tower tubes (H-Head, M-Middle, F-Feed)
More information.98M Ku-BAND Rx/Tx ANTENNA SYSTEM
Revision C January 2, 2002 ASSEMBLY MANUAL ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 ANTENNA SYSTEM C Revised Series text B Revised Address 1/2/02 RAH A Revise and Update
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationSubZero Plow System SEVERE INJURY, DEATH, OR EQUIPMENT DAMAGE MAY RESULT IF SAFETY INSTRUCTIONS ARE NOT FOLLOWED.
1 SubZero Plow System Check out our instructional video online at www.rockymountainatvmc.com/videos or on our Youtube channel under: RockyMountainATVMC Safety Instructions For your safety and the safety
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationReplacing the build plate clamps
Repair manual Replacing the build plate clamps Instructions The build plate clamps hold the glass plate in place on the heated bed. There are two fixed in place at the back of the heated bed and two at
More informationCONTENTS Preparation Functions and Indications Operation
CONTENTS Features 3 Preparation Parts of the detector 4 Assembling the detector 4 Adjusting the search coil 6 Installing the batteries 6 Using the headphones 7 Functions and Indications Parts of the control
More informationPERSONAL RECORD KEEPING
Q47e/Q47ce 2 Q 4 7 e / Q 4 7 c e A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING IMPORTANT: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make
More informationQ-Zone Hoop-Frame. Assembly Instructions. Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8
Q-Zone Hoop-Frame Assembly Instructions Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8 Table of Contents Table of Contents... i Warranty... ii Parts List Box 1...iii Box 2...
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationAssembly Manual for the 1.2m Quick-Deploy Antenna System
704 North Clark Street Albion, MI 49224 USA Phone +1 517 680 0125 Fax +1 517 680 0133 www.challengercommunications.com Challenger Communications Assembly Manual for the 1.2m Quick-Deploy Antenna System
More informationINSTRUCTION. Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W V7002-1S W8103-1S. No Third edition : March 2001
INSTRUCTION Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W8042-1 V7002-1S W8103-1S Third edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's V.W
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationDiode Pointer Quick Start Guide
Important Note: Read all Danger, Warning, Caution terms, symbols, and instructions located on our website. The diode pointer provides a safety measure by enabling operators to monitor the location of the
More informationRemarks: Before Installation, please read the instruction carefully.
60 cm antenna Z24A60T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.6m ultra-high performance microwave antenna. Installation,
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More information.74m Ka-Band Antenna Installation Guide Model: AN8-074P
.74m Ka-Band Antenna Installation Guide Model: AN8-074P 1037749-0001 Revision A March 26, 2008 Revision record Revision Date of issue Scope A March 26, 2008 Production Release Copyright 2008 Hughes Network
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationInstruction Manual. Quick Setup
Instruction Manual Quick Setup Make sure the Carryout G2 antenna is in a location with a clear view of the southern sky. Connect the provided coaxial cable from the primary receiver to the MAIN port on
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationSELFSAT-H10D. What is SELFSAT-H10D? Warning!!! Safety Instructions
SELFSAT-H0D What is SELFSAT-H0D? SELFSAT-H0D is a Horn Array Type Satellite Antenna with Dual Linear Polarization, it can receive signal from major Satellites and would replace a normal former Parabolic
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationInstalling the 3 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing the 3 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Route Cable into Box...5
More informationInstallation Guide. Hiltron Motorized Antenna Mount HMAM
HMAM_Install_A.doc Page 1 of 20 Installation Guide for Hiltron Motorized Antenna Mount HMAM HMAM_Install_A.doc Page 2 of 20 Table of Contents 1 Overview...3 2 Unpacking and Inspection...3 3 Contents of
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationMOTOR REPLACEMENT : STEP BY STEP.
(D) REPLACEMENT : STEP BY STEP. (V) Adjustment screw (Allen key 3/16 ) (E) (U) (I) Tightening screw (Allen key 5/32 ) Blocking screw (H) (Allen key 5/32 ) (G) (Y) (T) (ZZ) (Z) (K) (X) (L) (S) (W) (R) (Q)
More informationTorqueMaster Replacement Spring
TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton
More informationCNC Router Parts. Standard Rack & Pinion Drive Assembly Instructions
CNC Router Parts Standard Rack & Pinion Drive Tools List The following tools will be used for assembly and installation of the Standard Rack & Pinion Drive: Imperial Allen Wrench Set - 3/32", 5/32", 3/16",
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationDISH SETUP INSTRUCTIONS 3 FOOT DISH
DISH SETUP INSTRUCTIONS 3 FOOT DISH 1. The satellite dish will look like this when completed. 2. First, select a roomy working location and lay out all your parts and pieces for easy identification. Don
More informationMODEL H-9 HEAVY DUTY BENCH-TYPE UNDERCUTTER INSTRUCTIONS
MODEL H-9 HEAVY DUTY BENCH-TYPE UNDERCUTTER INSTRUCTIONS CAPACITY: Between centers - 32" long x 12" diameter. Between roller V- supports - 35" long x 17" diameter. Maximum armature weight - 200 lbs. SAW
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More information.98m Ka-Band Antenna Installation Guide Model: AN8-098P
.98m Ka-Band Antenna Installation Guide Model: AN8-098P 1037750-0001 Revision A January 30, 2009 Revision record Revision Date of issue Scope A January 30, 2009 Initial release Copyright 2009 Hughes Network
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationFD 2002IL AutoSeal System
FD 2002IL AutoSeal System 4/2017 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 1 SETUP 2 Sealer Alignment Base Setup 2 Sealer Setup 2-4 Printer Alignment Base
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain
ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance
More information